INDUCTION COOKTOP
OPERATING & INSTALLATION
MANUAL FOR MODEL ILD9E

OPEN 24/7
ILVE ACCESSORIES ONLINE SHOP

For a wide range of cofee machines and other genuine ILVE accessories at the click of a button shop.ilve.com.au

Congratulations,

you are now the proud owner of an ILVE cooking appliance.
Thank you for purchasing ILVE and welcome to the exciting world of cooking the ILVE way.
This instruction manual has been specially created to inform you of the full range of features your ILVE appliance has to offer and serves as an introduction to the wonderful benefits of ILVE’s dynamic cooking systems.
We present detailed information on each of the advanced cooking systems built into ILVE appliances. Once you have read this section you will be able to choose the most appropriate settings for your appliance when cooking different types of food.
We ask you to read the instructions in this booklet very carefully as this will allow you to get the best results from using your appliance.
KEEP THE DOCUMENTATION OF THIS PRODUCT FOR FUTURE REFERENCE.

SAFETY

Precautions before using

• Unpack all the materials.
• The installation and connecting of the appliance have to be done by approved specialists. The manufacturer can not be responsible for damage caused by building-in or connecting errors.
• To be used, the appliance must be well-equipped and installed in a kitchen unit and an adapted and approved work surface.
• This domestic appliance is exclusively for the cooking of food, to the exclusion of any other domestic, commercial or industrial use.
•  Remove all labels and self-adhesives from the ceramic glass.
• Do not change or alter the appliance.
• The cooking plate can not be used as freestanding or as a working surface.
• The appliance must be grounded and connected conforming to local standards.
• Do not use any extension cable to connect it.
• The appliance can not be used above a dishwasher or a tumble-dryer: steam may damage the electronic appliances.
• The appliance is not intended to be operated by means of an external timer or separate remote control system.

Using the appliance

• Switch the heating zones off after using.
• Keep an eye on the cooking using grease or oils: that may quickly ignite.
• WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in a fire.
• Be careful not to burn yourself while or after using the appliance.
• Make sure no cable of any fixed or moving appliance contacts with the glass or the hot saucepan.
• Magnetic objects (credit cards, floppy disks, calculators) should not be placed near to the engaged appliance.
• Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot.
• In general, do not place any metallic object except heating containers on the glass surface. In case of untimely engaging or residual heat, this one may heat, melt or even burn.
• Never cover the appliance with a cloth or a protection sheet. This is supposed to become very hot and catch fire.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.

Precautions not to damage the appliance

• Raw pan bottoms or damaged saucepans (not enameled cast iron pots,) may damage the ceramic glass.
• Sand or other abrasive materials may damage ceramic glass.
• Avoid dropping objects, even little ones, on the vitro ceramic.
• Do not hit the edges of the glass with saucepans.
• Make sure that the ventilation of the appliance works according to the manufacturer’s instructions.
• Do not put or leave empty saucepans on the vitro ceramic hobs.
• Sugar, synthetic materials or aluminum sheets must not contact the heating zones. These may cause breaks or other alterations of the Vitro ceramic glass by cooling:  switch on the appliance and take them immediately out of the hot heating zone (be careful: do not burn yourself).
• WARNING: Danger of fire: do not store items on the cooking surface.
• Never place any hot container over the control panel.
• If a drawer is situated under the embedded appliance, make sure the space between the content of the drawer and the inferior part of the appliance is large enough (2 cm).  This is essential to guaranty correct ventilation.
• Never put any inflammable object (ex. sprays) into the drawer situated under the vitro ceramic hob. The eventual cutlery drawers must be resistant to heat.

Precautions in case of appliance failure

• If a defect is noticed, switch on the appliance and turn off the electrical supply.
• If the ceramic glass is cracked or fissured, you must unplug the appliance and contact the after-sales service.
• Repairing has to be done by specialists. Do not open the appliance by yourself.
• WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of electric shock.
• If the supply cord is damaged, it must be replaced by a cable special set available by the manufacturer or his after-sale service.

Other protections

• Note sure that the container pan is always centered on the cooking zone. The bottom of the pan must have to cover as much as possible the cooking zone.
• For the users of pacemakers, the magnetic field could influence its operating. We recommend getting information to the retailer or of the doctor.
• Do not to use aluminum or synthetic material containers: they could melt on still hot cooking zones.
• NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.

THE USE OF EITHER A POOR QUALITY POT OR ANY INDUCTION ADAPTOR PLATE FOR NON-MAGNETIC COOKWARE RESULTS IN A WARRANTY  BREACH. IN THIS CASE, THE MANUFACTURER CANNOT BE HELD RESPONSIBLE FOR ANY DAMAGE CAUSED TO THE HOB AND/OR ITS  ENVIRONMENT.

DESCRIPTION OF THE APPLIANCE

Technical characteristics

* The given power may change according to the dimensions and material of the pan.

Control panel

USE OF THE APPLIANCE

Display

Ventilation

The cooling system operates continuously. He starts when turning on the hob and speeds up when the hob is used intensively. The cooling fan reduces its speed and stops automatically when the electronic circuit is cooled enough.

STARTING-UP AND APPLIANCE MANAGEMENT

Before the first use

Clean your hob with a damp cloth, and then dry the surface thoroughly. Do not use detergent which risks causing blue-tinted colour on the glass surface.

Induction principle

An induction coil is located under each heating zone. When it is engaged, it produces a variable electromagnetic field which produces inductive currents in the ferromagnetic bottom plate of the pan. The result is a heating-up of the pan located on the heating zone.
Of course, the pan has to be adapted:

• All ferromagnetic pans are recommended (please verify it thanks to a little magnet): cast iron and steel pans, enameled pans, stainless-steel pans with ferromagnetic bottoms…
• Are excluded: cupper, pure stainless steel, aluminum, glass, wood, ceramic, stoneware,… The induction heating zone adapts automatically the size of the pan. With a too-small diameter, the pan doesn’t work. This diameter is varying in the function of the heating zone diameter.
  If the pan is not adapted to the induction hob the display will show [ U ].

Sensitive touch

Your ceramic hob is equipped with electronic controls with sensitive touch keys. When your finger presses the key, the corresponding command is activated. This activation is validated by a control light, a letter or a number in the display and/or a “beep” sound.
In the case of general use press only one key at the same time.

Starting-up

You must first switch on the hob, then the heating zone:

• Start-up/ switch off the hob :

• Start-up/ switch off a heating zone :

If no action is made within 20 seconds the electronics return in the waiting position.

Pan detection

The pan detection ensures perfect safety. The induction doesn’t work:

• If there is no pan on the heating zone or if this pan is not adapted to the induction. In this case it is impossible to increase the power and the display shows [ U ]. This symbol disappears when a pan is put on the heating zone.
•  If the pan is removed from the heating zone the operation is stopped. The display shows [ U ]. The symbol [ U ] disappears when the pan is put back to the heating zone. The cooking continues with the power level set before.
  After use, switch the heating element off: don’t let the pan detection [ U ] active.

Residual heat indication

After the switch-off of a heating zone or the complete stop of the hob, the heating zones are still hot and indicates [ H ] on the display.
The symbol [ H ] disappears when the heating zones may be touched without danger. As far as the residual heat indicators are on light, don’t touch the heating zones and don’t put any heat-sensitive objects on them.  There are risks of burn and fire.

Booster function
The Booster function [ P ] and the Double Booster [ ] add a boost of power to the selected
heating zone.
If this function is activated the heating zones work for 5 minutes with ultra high power.
The booster is foreseen for example to heat up rapidly big quantities of water, like nuddles cooking.

• Startup / Stop the booster function :

• Startup / Stop the double booster function:

Action	Control panel	Display
Zone selection Increase power Start up the booster Start up the Double Booste Stop the Double Booster	Press key [ O ] Press key [ + ] Press key [ + ] Press key [ + ] Press key [ – ]	[ 0 ] [ 1 ] to [ 9 ] [ P ] during 5 min[and P ] [ 0 ] to [ P ]

• Power management:

When it comes to the power, the cooking zones are running by pairs and cannot exceed an overall maximum of power. If the selected heating levels for both zones exceed the maximum available amount of power, the power management function is automatically reducing the power from one of these zones. The display of this zone is first blinking;  the level is then automatically reduced to the highest suitable position.

Note: if the two left cooking zones are used at the maximal power level, the middle cooking zone is unusable.

Timer
The timer is able to be used simultaneously with all heating zones and this with different time settings (from 0 to 99 minutes) for each heating zone.

• Setting and modification of the cooking time :

After a few seconds, the control light stops blinking.
The time is confirmed and the cooking starts until the time reaches [ 00 ].

• To stop the cooking time :

• Automatic stop at the end of the cooking time :
As soon as the selected cooking time is finished the timer displays blinking [ 00 ] and a sound rings.
To stop the sound and the blinking it is enough to press any key.

Control panel locking

To avoid modifying a set of cooking zones, in particular within the framework of cleaning
the control panel can be locked (with the exception to the On/Off key [I]).

• Locking :

• Unlocking :

In the 5 seconds after start :

Automatic cooking

All the cooking zones are equipped with an automatic cooking device. The cooking zone starts at full power for a certain time and then reduces automatically its power to the pre-selected level.

• Start-up :

• Switching off the automatic cooking :

Bridge

This function allows using 2 cooking zones at the same time with the same features as a single cooking zone. Booster function isn’t allowed.

Pause function

This function breaks all the hob’s cooking activity and allows restarting with the same settings.

• Startup/stop the pause function :

Recall Function

After switching off the hob ( I), it is possible to recall the last settings.

•  cooking stages of all cooking zones (power)
• minutes and seconds of programmed cooking zone-related timers
• Keep warm function
  The recall procedure is following:
• Press the key [I]
• Then press the key [ II ] within 6 seconds
  The precedent settings are activated.

Keep Warm

This function allows to reach and maintain automatically a temperature of 70°C.
This will avoid liquids overflowing and fast-burning at the bottom of the pan.

• To engage, to start the function « Keep warm » :

This function can be started independently on all the heating zones.
When the pan leaves the cooking zone of the “Keep warm” function remains active for approximately 10 minutes.
The maximum duration of keeping warm is 2 hours.

My Function

After having set the cooking level and timer value for the zone, it is possible to memorize the settings on the same zone.

• cooking stages of the cooking zone (power)
• minutes and seconds of programmed cooking zone-related timer
• Keep warm function
• Automatic cooking function

• To register a memory program for a cooking zone:

If no memorizing is made within timer validation the electronics return in cooking position.

Cooking zone runs with cooking level and timer value registered in the memory program.

COOKING ADVICE

Pan quality
Adapted materials: steel, enameled steel, cast iron, ferromagnetic stainless steel, aluminum with the ferromagnetic bottom.
Not adapted materials: aluminum and stainless steel without ferromagnetic bottom, copper, brass, glass, ceramic, porcelain.
The manufacturers specify if their products are compatible with induction.
To check if pans are compatibles :

• Put a little water in a pan placed on an induction heating zone set at level [ 9 ]. This water must heat in a few seconds.
• A magnet sticks on the bottom of the pan.
  Certain pans can make noise when they are placed in an induction cooking zone. This noise doesn’t mean any failure on the appliance and doesn’t influence the cooking operating.

Pan dimension

The cooking zones are, until a certain limit, automatically adapted to the diameter of the pan.
However, the bottom of this pan must have a minimum of diameter according to the corresponding cooking zone.
To obtain the best efficiency of your hob, please place the pan well in the center of the cooking zone.

Examples of cooking power setting

(the values below are indicative)

MAINTENANCE AND CLEANING

Switch off the appliance before cleaning.
Do not clean the hob if the glass is too hot because they are risk of burn.

• Remove light marks with a damp cloth with washing up liquid diluted in a little water. Then rinse with cold water and dry the surface thoroughly.
• Highly corrosive or abrasive detergents and cleaning equipment likely to cause scratches must be absolutely avoided.
• Do not ever use any steam-cleaner or pressure washer. Do not use any object that may scratch the ceramic glass.
• Ensure that the pan is dry and clean. Ensure that there are no grains of dust on your ceramic hob or on the pan. Sliding rough saucepans will scratch the surface.
• Spillages of sugar, jam, jelly, etc. must be removed immediately. You will thus prevent the surface being damaged.

WHAT TO DO IN CASE OF A PROBLEM

When the symbol [ E 4 ] appears :

I) The hob must be reconfigured according to the following procedure :
Before you start the procedure :
– Make sure that there is no more pot on the hob.
– Use a pan adapted to induction.
– Disconnect the appliance from the electrical network by removing the fuse or turning the circuit breaker off.
– Reconnect the table to the electrical network.
– It is necessary to start the procedure within 2 minutes after the connection of the hob to the electrical network.
– Do not press the [ 0/I ] key.

II) Cancellation of the existing configuration :
1) Press the key B and hold down.
2) With your other hand, press key A during 2s.
Released the key A.
A “bip” sound.
A double “bip” means an error occurred.
If so, start again from item 1).
3) Press the key C, always with your finger on the key B.
A “bip” sound if manipulation is succeeded, if it
isn’t so, start again from item 1).
4) Remove your fingers from the touch control, then press again on key A during few
seconds, until blinking [ E ] symbols appear.
5) Wait until [ E ] symbols stop blinking.
6) After few seconds, [ E ] are automatically transformed in [ C ]. The existing setup has been canceled.

III) How to reconfigure the hob?
1) Take a ferromagnetic pot with a minimum diameter of 16 cm.
2) Select a cooking zone by pushing on the corresponding key.
3) Place the pot on the area to be set.
4) Wait until the [ C ] display becomes a [ – ]. The selected cooking zone is configured.
5) Follow the same procedure for each cooking zone with a [ C ] display.
6) All the cooking zones are configured once all the displays are turned off.
Please use the same pot for the whole procedure.
Never put several pots together on the zones during the setup process.
– If [ E 4 ] displaying remains, please call customer care.
The hob or the cooking zone doesn’t startup:

• The hob is badly connected on the electrical network.
• The protection fuse cut-off.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.

The control panel displays [ U ] :

• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.

Continuous ventilation after cutting off the hob :

• This is not a failure, the fan continuous to protect the electronic device.
• The fan cooling stops automatically.

One or all cooking zone cut-off :

• The safety system functioned.
• You forgot to cut off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level and breaking Automatic overheating
• The cooling can be insufficient. It is recommended to open the kitchen furniture back wall on the width of the cut out of the hob and plane the front cross member of kitchen furniture on the whole width of the cut out to allow an air passage under the worktop.

The control panel displays [ L ] :

• Refer to the chapter control panel locking page.

The control panel displays [ ] or [ Er03 ] :

• An object or liquid covers the control keys. The symbol disappears as soon as the released or cleaned.

The control panel displays [ E2 ] or [ EH ] :

• The hob is overheated, let it cool and then turn it on again.

The control panel displays [ E3 ] :

• The pan is not adapted, change the pan.

The control panel displays [ E5 ] :

• Defective network. Control the voltage of the electrical network.

The control panel displays [ E6 ] :

• Defective network. Control the frequency of the electrical network.

The control panel displays [ E8 ] :

• The air inlet of the ventilator is obstructed, release it.

If one of the symbols above persists, call the SAV.

ENVIRONMENT PRESERVATION

• The materials of packing are ecological and recyclable.
• Electronic appliances are composed of recyclable, and sometimes harmful materials for the environment, but necessary to the good running and the safety of the appliance.

• Don’t throw your appliance with the household refuses
• Get in touch with the waste collection center of your commune that is adapted to the recycling of household appliances.

INSTALLATION INSTRUCTIONS

The installation comes under the exclusive responsibility of specialists.
The installer is held to respect the legislation and the standards enforce in his home country.
How to stick the gasket:
The gasket supplied with the hob avoids all infiltration of liquids in the cabinet.
His installation has to be done carefully, in conformity of the following drawing.

Stick the gasket (2) two millimeters from the external edge of the glass,  after removing the protection sheet (3).

Fitting – installing:

The cut out sizes are:

• Ensure that there is a distance of 50 mm between the hob and the wall or sides.
• The hobs are classified as “Y” class for heat protection. Ideally, the hob should be installed with plenty of space on either side. There may be a wall at the rear and tall units or an all at one side. On the other side, however, no unit or divider must stand higher than the hob.
• The piece of furniture or the support in which the hob is to be fitted, as well as the edges of furniture, the laminate coatings and the glue used to fix them, must be able to resist temperatures of up to 100 °C.
• The mural rods of the edge must be heat-resisting.
• Not to install the hob to the top of a not ventilated oven or a dishwasher.
• To guarantee under the bottom of the hob casing a space of 20 mm to ensure a good air circulation of the electronic device.
• If a drawer is placed under the work, avoid putting into this drawer flammable objects (for example sprays) or not heat-resistant objects.
• Materials that are often used to make worktops expand on contact with water. To protect the cutout edge, apply a coat of varnish or special sealant. Particular care must be given to applying the adhesive joint supplied with the hob to prevent any leakage into the supporting furniture. This gasket guarantees a correct seal when used in conjunction with smooth work top surfaces.
•  The safety gap between the hob and the cooker hood placed above must respect the indications of the hood manufacturer. In case of absence of instructions respect a distance minimum of 650 mm.
• The connection cord should be subjected, after building, with no mechanical constraint, such for example of the fact of the drawer.
• WARNING: Use only hob guards designed by the manufacturer of the cooking appliance or indicated by the manufacturer of the appliance in the instructions for use as suitable or hob guards incorporated in the appliance. The use of inappropriate guards can cause accidents.

• A separation panel at least 20mm from the bottom of the cooktop must be included during installation to prevent access to the underside of the appliance. This panel can be made of any non-combustible rigid material. If the hob is going to be installed on the top of an oven, precautions must be taken to guarantee an installation in accordance with current accident prevention standards. Pay particular attention to the position of the electric cable: he must not touch any hot parts of the oven.

ELECTRICAL CONNECTION

• The installation of this appliance and the connection to the electrical network should be entrusted only to an electrician perfectly to the fact of the normative regulations and which respects them scrupulously.
• Protection against the parts under tension must be ensured after the building-in.
• The data of connection necessary are on the stickers place on the hob casing near the connection box.
• The connection to the main must be made using an earthed plug or via an omnipolar circuit-breaking device with a contact opening of at least 3 mm.
• The electrical circuit must be separated from the network by adapted devices, for example: circuit breakers, fuses or contactors.
•  If the appliance is not fitted with an accessible plug, disconnecting means must be incorporated in the fixed installation, in accordance with the installation regulations.
• The inlet hose must be positioned so that it does not touch any of the hot parts of the honor even.

Caution!
This appliance has only to be connected to a network 230 V~ 50/60 Hz.
Connect always the earth wire.
Respect the connection diagram.
The connection box is located underneath at the back of the hob casing. To open the cover use a medium screwdriver. Place it in the slits and open the cover.

* calculated with the simultaneous factor following the standard EN 60 335-2-6

Connection of the hob
Setting up the configurations:
For the various kinds of connection, use the brass bridges which are in the box next to the terminal
Monophase 230V~1P+N
Put a bridge between terminals 1 and 2.
Attach the earth to the terminate “earth”, the neutral N to terminal 4, the Phase L to one of the terminals 1 or 2.
Biphase 400V~2P+N
Attach the earth to the terminate “earth”, the neutral N to terminal 4, the Phase L1 to terminals 1 and the Phase L2 to terminal 2.

Caution!

Frequent loosening and screwing of the screws on the connection box risks damaging the efficiency of the tightness once screwed. It is therefore advisable to keep screwing and unscrewing to a minimum. Ensure that the cables are correctly inserted and tightly screwed down.

We cannot be held responsible for any incident resulting from the incorrect connection or   which could arise from the use of an appliance that has not been earthed or has been
equipped with a faulty earth connection.

WARRANTY CARD

Eurolinx Pty Limited A.B.N. 50 001 473 347 trading as ILVE (“ILVE”) Office:
48-50 Moore Street, Leichhardt N.S.W 2040 Post:
Locked Bag 3000, Annandale, N.S.W 2038 P: 1300 856 411
WARRANTY REGISTRATION
Your ongoing satisfaction with your ILVE product is important to us. We ask that you complete the
enclosed Warranty Registration Card and return  it to us so that we have a record of the ILVE product purchased by you, Alternatively, you can   now register your warranty  online at http://support.eurolinx.com.au/ 
PRIVACY
ILVE resp ects your privacy and is committed to handling your personal information in accordance with the National Privacy Principles and the Privacy Act 1988 (Cth). A copy of the ILVE Privacy Policy is available at www.ilve.com.au. ILVE will not disclose any personal information set out in the Warranty Registration  Card (“Personal  Information”) without your consent unless required by: 1. law; 2. any ILVE related company; 3. any service provider which provides services to ILVE or assists ILVE in providing services (including repair and warranty services) to customers. Our purpose in collecting the Personal Information is to keep a record of the ILVE product purchased y you, in order to provide better warranty service to you in the unlikely event that there is a problem with your ILVE product. ILVE may contact you at anyone or ore of the addresses, email addresses or telephone numbers set out in the Warranty Registration Card. Please contact ILVE on 1300 694 583 should you not wish to be contacted by I’VE.

WARRANTY

• Warranty ILVE warrants that each ILVE product will remain, for a period of twenty-four (24) months computed from the date of purchase f the ILVE product, free from defects arising in the manufacture of the ILVE product (“Warranty”). Except for consumer guarantees set out in the Competition and Consumer ct 2010 (Cth) (“Act”), ILVE does not make any further warranties or representations in relation to ILVE products.
• What is not covered by the Warranty.
  The Warranty does not apply if an ILVE product is defective by a factor other than a defect arising in the manufacture of the ILVE product, including  but not limited to:
  (a) damage through misuse (including failure to maintain, service or use with proper care), neglect, accident or ordinary wear and tear  (including deterioration of parts and  accessories and glass breakage);
  (b) use for purpose for which the ILVE product was not sold or designed;
  (c) use or installation which is not in accordance  with any specified instructions for use or installation;
  (d) use or operation after a defect has occurred or been discovered;
  (e) damage through freight, transportation or handling in transit (other than when ILVE is responsible);
  (f) damage through exposure to chemicals, dust, residues, excessive voltage, heat, atmospheric  conditions or other forces or environmental factors outside the control or ILVE;
  (g) repair, modification or tampering by the purchaser or any person other than ILVE, an employee of ILVE or an authorized ILVE service contractor*;
  (h) use of parts, components or accessories which have not been supplied or specifically approved by ILVE.
  (i) damage to surface coatings caused by cleaning or maintenance using products not recommended in the ILVE product handbook provided to the purchaser upon purchase of the ILVE product;
  (j) damage to the base of an electric oven due to items having been placed on the base of the oven cavity or covering the base, such as aluminium foil (this impedes the transfer  of heat from the element to the oven cavity and can result in irreparable damage); or
  (k) damages, dents or other cosmetic imperfections not afecting the performance of the ILVE in respect of an ILVE product purchased as a “factory second” or from display
  The Warranty does not extend to light globes used in ILVE products.
• Domestic Use
  Each ILVE product is made for domestic use. This Warranty may not extend to ILVE products used for commercial purposes.
• Time for Claim under the Warranty
  You must make any claim under this Warranty within twenty-eight (28) days after the occurrence of an event that gives rise to a claim pursuant to the Warranty, by booking a  service call on the telephone number below. Continued over…
• Proof of Purchase
  Customers must retain proof of purchase in order to be eligible to make a warranty claim in respect of an ILVE product.
•  Claiming under the Warranty
  Customers will bear the cost of claiming under this Warranty unless ILVE determines the expenses are reasonable, in which case the customer must claim those expenses by providing written evidence of each expense to ILVE at the address on the Warranty Registration Card.
•  Statutory Rights
  (a) These terms and conditions do not afect your statutory rights.
  (b) The limitations on the Warranty set out in this document do not exclude or limit the application of the consumer guarantees set out in the Act or any other equivalent or  corresponding legislation in the relevant jurisdiction where to do so would:
  (i) contravene the law of the relevant jurisdiction;or
  (ii) cause any part of the Warranty to be void.
  (c) ILVE excludes indirect or consequential loss of any kind (including, without limitation, loss of use of the ILVE product) and (other than expressly provided for in these  terms and conditions) subject to all terms, conditions and warranties implied by custom, the general law, the Act or other statute.
  (d) The liability of ILVE to you for a breach of any express or non-excludable implied term, condition or warranty is limited at the option of ILVE to:
• (i) replacing or repairing the defective part of the ILVE product;
  (ii) paying the cost of replacing or repairing the defective part of the ILVE product;
  (iii) replacing the ILVE product; or
  (iv) paying the cost of replacing the ILVE product.
  (e) Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and  the failure does not amount to a major failure.
  8. Defects
  Any part of an ILVE product deemed to be defective and replaced by ILVE is the property of ILVE. ILVE reserves the right to inspect and test ILVE products in order to determine the extent of any defect and the validity of a claim under the Warranty.
  *For your closest ILVE authorized service agent go to https://support.eurolinx.com.au/#/map/retailers
  All warranty service calls must be booked through ILVE’s Customer Care Centre on [email protected] or 1300 85 64 11 option 101012018

Warranty Card tear-off

WARRANTY REGISTRATION CARD
01032017
Please complete and send to ILVE at REPLY PAID 83617
LEICHHARDT NSW 2040

Australia National Telephone Number 1300 MYILVE (694 583) New Zealand Telephone Number 0508 458 369 ILVE showrooms are open Tuesday – Friday: 9 am-5pm and Saturdays 10 am-4 pm. Closed on Monday & Sunday

ilve.com.au

INDUCTION COOKTOP
OPERATING & INSTALLATION
MANUAL FOR MODEL ILD6E

OPEN 24/7
ILVE ACCESSORIES ONLINE SHOP

For a wide range of cofee machines and other genuine ILVE accessories at the click of a button shop.ilve.com.au

Congratulations,

you are now the proud owner of an ILVE cooking appliance.
Thank you for purchasing ILVE and welcome to the exciting world of cooking the ILVE way.
This instruction manual has been specially created to inform you of the full range of features your ILVE appliance has to offer and serves as an introduction to the wonderful benefits of ILVE’s dynamic cooking systems.
We present detailed information on each of the advanced cooking systems built into ILVE appliances. Once you have read this section you will be able to choose the most appropriate settings for your appliance when cooking different types of food.
We ask you to read the instructions in this booklet very carefully as this will allow you to get the best results from using your appliance. KEEP THE DOCUMENTATION OF THIS PRODUCT FOR FUTURE REFERENCE.

SAFETY

Precautions before using

• Unpack all the materials.
• The installation and connecting of the appliance have to be done by approved specialists. The manufacturer can not be responsible for damage caused by building-in or connecting errors.
• To be used, the appliance must be well-equipped and installed in a kitchen unit and an adapted and approved work surface.
• This domestic appliance is exclusively for the cooking of food, to the exclusion of any other domestic, commercial or industrial use.
• Remove all labels and self-adhesives from the ceramic glass.
•  Do not change or alter the appliance.
• The cooking plate can not be used as a freestanding or as a working surface.
• The appliance must be grounded and connected conforming to local standards.
• Do not use any extension cable to connect it.
• The appliance can not be used above a dishwasher or a tumble dryer: steam may damage the electronic appliances.
• The appliance is not intended to be operated by means of an external timer or separate remote control system.

Using the appliance

• Switch the heating zones off after using.
• Keep an eye on the cooking using grease or oils: that may quickly ignite.
• WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in a fire.
• Be careful not to burn yourself while or after using the appliance.
• Make sure no cable of any fixed or moving appliance contacts with the glass or the hot saucepan.
• Magnetic objects (credit cards, floppy disks, calculators) should not be placed near to the engaged appliance.
• Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot.
• Do not place any metallic object except heating containers. In case of untimely engaging or residual heat, this one may heat, melt or even burn.
• Never cover the appliance with a cloth or a protection sheet. This is supposed to become very hot and catch fire.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.

Precautions not to damage the appliance

• Raw pan bottoms or damaged saucepans (not enameled cast iron pots,) may damage the ceramic glass.
• Sand or other abrasive materials may damage ceramic glass.
• Avoid dropping objects, even little ones, on the vitroceramic.
• Do not hit the edges of the glass with saucepans.
• Make sure that the ventilation of the appliance works according to the manufacturer’s instructions.
• Do not put or leave empty saucepans on the vitroceramic hobs.
• Sugar, synthetic materials or aluminum sheets must not contact with the heating zones. These may cause breaks or other alterations of the vitroceramic glass by cooling: switch on the appliance and take them immediately out of the hot heating zone (be careful: do not burn yourself).
• WARNING: Danger of fire: do not store items on the cooking surface.
• Never place any hot container over the control panel.
• If a drawer is situated under the embedded appliance, make sure the space between the content of the drawer and the inferior part of the appliance is large enough (2 cm). This is essential to guaranty correct ventilation.
• Never put any inflammable object (ex. sprays) into the drawer situated under the vitroceramic hob. The eventual cutlery drawers must be resistant to heat.

Precautions in case of appliance failure

• If a defect is noticed, switch on the appliance and turn off the electrical supply.
• If the ceramic glass is cracked or fissured, you must unplug the appliance and contact the after-sales service.
• Repairing has to be done by specialists. Do not open the appliance by yourself.
• WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of electric shock.
• f the supply cord is damaged, it must be replaced by a cable or special set available by the manufacturer or his after-sale service.

Other protections

• Note sure that the container pan is always centered on the cooking zone. The bottom of the pan must have to cover as much as possible the cooking zone.
• For the users of pacemakers, the magnetic field could influence its operating. We recommend getting information to the retailer or of the doctor.
• Do not use aluminum or synthetic material containers: they could melt on still-hot cooking zones.
• NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.

THE USE OF EITHER A POOR QUALITY POT OR ANY INDUCTION ADAPTOR PLATE FOR NON-MAGNETIC COOKWARE RESULTS IN A WARRANTY BREACH.
IN THIS CASE, THE MANUFACTURER CANNOT BE HELD RESPONSIBLE FOR ANY DAMAGE CAUSED TO THE HOB AND/OR ITS ENVIRONMENT. 

DESCRIPTION OF THE APPLIANCE

Technical characteristics

* The given power may change according to the dimensions and material of the pan.

Control panel

USE OF THE APPLIANCE

Display 0 1…9 U A E H P L U II

Designation Zero Power level Pan detection Heat accelerator Error message Residual heat Booster Double Booster Locking Keep warm Pause Bridge

Function The heating zone is activated. Selection of the cooking level. No pan or inadequate pan. Automatic cooking. Electronic failure. The heating zone is hot. The boosted power is activated. The double boosted power is activated. Control panel locking. Maintain automatically of 70°C. The hob is in pause. 2 cooking zones are combined.

Ventilation

The cooling system is fully automatic. The cooling fan starts with a low speed when the calories brought out by the electronic system reach a certain level. The ventilation starts his high speed when the hob is intensively used. The cooling fan reduces his speed and stops automatically when the electronic circuit is cooled enough.

STARTING-UP AND APPLIANCE MANAGEMENT

Before the first use

Clean your hob with a damp cloth, and then dry the surface thoroughly. Do not use detergent which risks causing blue-tinted colour on the glass surface.

Induction principle

An induction coil is located under each heating zone. When it is engaged, it produces a variable electromagnetic field which produces inductive currents in the ferromagnetic bottom plate of the pan. The result is a heating-up of the pan located on the heating zone.
Of course the pan has to be adapted:

• All ferromagnetic pans are recommended (please verify it thanks to a little magnet): cast iron
  and steel pans, enameled pans, stainless-steel pans with ferromagnetic bottoms…
• Are excluded: cupper, pure stainless-steel, aluminum, glass, wood, ceramic, stoneware,…
  The induction heating zone adapts automatically to the size of the pan. With a too-small diameter, the pan doesn’t work. This diameter is varying in the function of the heating zone diameter.
  If the pan is not adapted to the induction hob the display will show [ U ].

Sensitive touch

Your ceramic hob is equipped with electronic controls with sensitive touch keys. When your finger presses the key, the corresponding command is activated. This activation is validated by a control light, a letter or a number in the display, and/or a “beep” sound.

In the case of general use press only one key at the same time.

Power selection zone “SLIDER” and timer setting zone
To select the power with the slider, slide your finger on the “SLIDER” zone. You can already have a direct access if you put your finger directly on the chosen level.

Starting-up

• Startup/switch off the hob:

Action	Control panel	Display
To start	press key [ ]	4 x [ 0 ] are blinking
To stop	press key [ ]	nothing or [ H ]

• Startup / switch off a heating zone:

If no action is made within 20 seconds the electronics return in the waiting position.

Pan detection

The pan detection ensures perfect safety. The induction doesn’t work:

• If there is no pan on the heating zone or if this pan is not adapted to the induction. In this case, it is impossible to increase the power and the display shows [ U ]. This symbol disappears when a pan is put on the heating zone.
• If the pan is removed from the heating zone the operation is stopped. The display shows [ U ].
  The symbol [ U ] disappears when the pan is put back to the heating zone. The cooking continues with the power level set before.

Residual heat indication

After the switch-off of a heating zone or the complete stop of the hob, the heating zones are still hot and indicates [ H ] on the display.
The symbol [ H ] disappears when the heating zones may be touched without danger.
As far as the residual heat indicators are on light, don’t touch the heating zones and don’t put any heat-sensitive objects on them. There are risks of burn and fire.

Booster function

The Booster function [ P ] and the Double Booster [ ] add a boost of power to the selected heating zone.
If this function is activated the heating zones work for 10 minutes with ultra-high power.
The booster is foreseen for example to heat up rapidly big quantities of water, like noodles cooking.

• Start up / Stop the booster function:

• Start up / Stop the double booster function:

Action	Control panel	Display Zone
Startup the booster Startup the Double Booster Stop the Double Booster	press key [ P ] Press 2 times the key [ P ] slide on the “SLIDER“ or press on [ P ]	[ P ] [ and P ] [ P ] to [ 0 ] [ 9 ]

• Power management:
  The hole cooking hob is equipped by a maximum of power. When the booster function is activated,and not to exceed the maximum power, the electronic system orders to reduce automatically the power level of another heating zone. The display is blinking on [ 9 ] during a few seconds and then shows the maximum of power allowed :

Heating zone selected
[ P ] is displayed
The other heating zone: (example: power level 9) [ 9 ] goes to [ 6 ] or [ 8 ] depending on the type of zone

Timer
The timer is able to be used simultaneously with all 3 heating zones and this with different time settings (from 0 to 99 minutes) for each heating zone.

• Setting and modification of the cooking time :

Example for 16 minutes at power 7 :

• To stop the cooking time:

Example for 13 minutes at power 7 :

• Automatic stop at the end of the cooking time:
  As soon as the selected cooking time is finished the timer displays blinking [ 00 ] and a sound rings. To stop the sound and the blinking it is enough to press the key [ 00 ].
• Egg timer function :

Example for 29 minutes :

Action	Control panel	Display
Activate the hob Select« Timer » Set the units Valid the units Set the tens Valid the tens	press display [ ] press display [ CL ] slide on the “SLIDER“ to [ 9 ] press display [ 09 ] slide on the “SLIDER“ to [ 2 ] press display [ 29 ]	zone control lights are on [ 00 ] [ 0 fixed ] [ 9 blinking ] [ 0 blinking ] [ 9 fixed ] [ 2 blinkings] [ 9 fixed ] [ 29 ]

After a few seconds, the control light stops blinking.
As soon as the selected cooking time is finished the timer displays blinking [ 00 ] and a sound rings.
To stop the sound and the blinking it is enough to press the display [ 00 ]. The hob switches off.

Automatic cooking
All the cooking zones are equipped with an automatic “go and stop” cooking device. The cooking zone starts at full power during a certain time, then reduces automatically its power on the preselected level.

• Start-up :

• Switching off the automatic cooking :

Pause function

This function brakes all the hob’s cooking activity and allows restarting with the same settings.

• Startup/stop the pause function :

Recall Function

After switching off the hob ( ), it is possible to recall the last settings.

• cooking stages of all cooking zones (power)
• minutes and seconds of programmed cooking zone-related timers
• Heat up function

The recall procedure is following:

• Press the key [ ]
• Then press the key [ II ] within 6 seconds

The precedent settings are activated.

Bridge Function
This function allows using of the 2 cooking zones at the same time with the same features as a single cooking zone. Booster function isn’t allowed.

Action	Control panel	Display
Activate the hob	Press display [ ]	[ 0 ] or [ H ] on the 4 displays
Activate the bridge	Press on the 2 cooking zones	[ 0 ] appears on the front zone
Increase bridge	Slide on the “SLIDER “ [ 1 to 9 ] or display [ U ]	[ ∏ ] on the rear zone. [ 1 to 9 ] or [ U ]
Stop the bridge	Press on the 2 cooking zones	[ 0 ] or [ H ] on the 2 zones

“Keep warm” Function
This function allows to reach and maintain automatically a temperature of 70°C.This will avoid liquids overflowing and fast-burning at the bottom of the pan.

• To engage, to start the function « Keep warm » :

Control panel locking

To avoid modifying a setting of cooking zones, in particular during of cleaning the control panel can
be locked (with exception to the On/Off key [ ].

• Locking :

Action	Control panel	Display
Start Hob locking	press on key [ ] press simultaneously [ P ] and [ 0 ]from the front right zone display re-press on display [ 0 ]	[ 0 ] or [ H ] on the displays no modification [ L ] on the displays

• Unlocking :

Action	Control panel	Display
Start	press on key [ ]	[ L ] on the displays

In the 5 seconds after start :

Action	Control panel	Display
Start In the 5 seconds after start : Unlocking the hob	press on key [ ] press simultaneously [ P ] and [[ L ] from the front right zone display press on key [ P ]	[ L ] on the displays [ 0 ] or [ H ] on the displays no light on the displays

COOKING ADVICE

Pan quality

Adapted materials: steel, enameled steel, cast iron, ferromagnetic stainless-steel, aluminum with the ferromagnetic bottom.
Not adapted materials: aluminum and stainless steel without ferromagnetic bottom, copper, brass, glass, ceramic, porcelain.
The manufacturers specify if their products are compatible with induction.
To check if pans are compatibles :

• Put a little water in a pan placed on an induction heating zone set at level [ 9 ]. This water must heat in a few seconds.
• A magnet sticks on the bottom of the pan.
  Certain pans can make noise when they are placed on an induction cooking zone. This noise doesn’t mean any failure on the appliance and doesn’t influence the cooking operating.

Pan dimension

The cooking zones are, until a certain limit, automatically adapted to the diameter of the pan.
However, the bottom of this pan must have a minimum of diameter according to the corresponding cooking zone.
To obtain the best efficiency of your hob, please place the pan well in the center of the cooking zone.

Examples of cooking power setting

(the values below are indicative)

MAINTENANCE AND CLEANING

Switch off the appliance before cleaning.
Do not clean the hob if the glass is too hot because they are at risk of burn.

• Remove light marks with a damp cloth with washing up liquid diluted in a little water. Then rinse with cold water and dry the surface thoroughly.
• Highly corrosive or abrasive detergents and cleaning equipment likely to cause scratches must be absolutely avoided.
• Do not ever use any steam-cleaner or pressure washer.
• Do not use any object that may scratch the ceramic glass.
• Ensure that the pan is dry and clean. Ensure that there are no grains of dust on your ceramic hob or on the pan. Sliding rough saucepans will scratch the surface.
• Spillages of sugar, jam, jelly, etc. must be removed immediately. You will thus prevent the surface being damaged.

WHAT TO DO IN CASE OF A PROBLEM

The hob or the cooking zone doesn’t start up:

• The hob is badly connected on the electrical network.• The protection fuse cut-off.
• The looking function is activated.
• The sensitive keys are covered of grease or water.
• An object is put on a key.

The control panel displays [ U ]:

• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
  The control panel displays [ E ] :
• Call the After-sales Service.
  The control panel displays [ L ] :
• Refer to the chapter control panel locking page.
  One or all cooking zone cut-off :
  
• The safety system functioned.
• You forgot to cut off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level and breaking Automatic overheating
  Continuous ventilation after cutting off the hob :
• This is not a failure, the fan continuous to protect the electronic device.
• The fan cooling stops automatically.
  The automatic cooking system doesn’t start up:
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
  The control panel displays [ U ] :
• Refer to the chapter “Keep warm“.
  The control panel displays [ II ]:
• Refer to the chapter “Pause “.
  The control panel displays [ ∏ ]:
• Refer to the chapter “Bridge“.

When the symbol [ E 4 ] appears :

• The table must be reconfigured. Please implement the following steps :
  I) Important : before you start, make sure there is no more pot on the hob
  II) Disconnect the appliance from the grid by removing the fuse or turning the circuit breaker off
  III) Reconnect the table to the grid
  IV) Procedure :
  * take a pot with a ferromagnetic bottom and a minimum diameter of 16 cm
  * start the procedure within 2 minutes after reconnecting the hob to the grid
  * don’t use the [ ] touch
  V) First step: cancel the existing configuration
  1) Press the touch n°2 and hold down
  2) The symbol [ – ] will appear on each display
  3) With your other hand, press successively and quickly (less than 2s) on each [ – ] display.
  Begin from the front right side and turn contrary clockwise, as described in the picture (from a to d).
  A double “beep” means an error occurred. If so, start again from item 1).
  4) Remove your fingers from the touch control, then push again on touch 1 for few seconds, until blinking [ E ] symbols appear.
  5) Wait until [ E ] symbols stop blinking.
  6) After few seconds, [ E ] is automatically transformed in [ C ]. The existing setup has been canceled.
  
  VI) Second step : new setup
  1) Take a ferromagnetical pot with a minimum diameter of 16 cm
  2) Select a cooking zone by pushing on the corresponding [ C ] display
  3) Place the pot on the area to be set
  4) Wait until the [ C ] display becomes a [ – ]. The selected cooking zone is now configured.
  5) Follow the same procedure for each cooking zone with a [ C ] display.
  6) All the cooking zones are configured once all the displays are turned off.
  Please use the same pot for the whole procedure.
  Never put several pots together on the zones during the setup process.
• If [ E 4 ] displaying remains, please call the customer care
  The control panel displays [ ] or [ Er03 ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or cleaned.
  The control panel displays [ E2 ] or [ EH ] :
• The hob is overheated, let it cool and then turn it on again.
  The control panel displays [ E3 ] :
• The pan is not adapted, change the pan.
  The control panel displays [ E6 ] :
• Defective network. Control the frequency and voltage of the electrical network.
  The control panel displays [ E8 ] :
• The air inlet of the ventilator is obstructed, release it.
  The control panel displays [ E C ] :
  Configuration error. Set the table again, referring to the chapter “The [E 4] appears.”If one of the symbols above persists, call the SAV.

ENVIRONMENT PRESERVATION

• The materials of packing are ecological and recyclable.
• Electronic appliances are composed of recyclable, and sometimes harmful materials for the environment, but necessary to the good running and the safety of the appliance.
  
• Don’t throw your appliance with the household refuse
• Get in touch with the waste collection center of your commune that is adapted to the recycling of household appliances.

INSTALLATION INSTRUCTIONS

The installation comes under the exclusive responsibility of specialists.
The installer is held to respect the legislation and the standards enforce in his home country.
How to stick the gasket:
The gasket supplied with the hob avoids all infiltration of liquids in the cabinet.
His installation has to be done carefully, in conformity of the following drawing.

Stick the gasket (2) two millimeters from the external edge of the glass, after removing the protection sheet (3).

Fitting – installing:

• The cut out sizes are:

• Ensure that there is a distance of 50 mm between the hob and the wall or sides.
• The hobs are classified as “Y” class for heat protection. Ideally, the hob should be installed with plenty of space on either side. There may be a wall at the rear and tall units or a wall at one side. On the other side, however, no unit or divider must stand higher than the hob.
• The piece of furniture or the support in which the hob is to be fitted, as well as the edges of furniture, the laminate coatings, and the glue used to fix them, must be able to resist temperatures of up to 100 °C.
• The mural rods of the edge must be heat-resisting.
• Not to install the hob to the top of a not ventilated oven or a dishwasher.
• To guarantee under the bottom of the hob casing a space of 20 mm to ensure a good air circulation of the electronic device.
• If a drawer is placed under the work, avoid putting into this drawer flammable objects (for example sprays) or not heat-resistant objects.
• Materials that are often used to make worktops expand on contact with water. To protect the cutout edge, apply a coat of varnish or special sealant. Particular care must be given to applying the adhesive joint supplied with the hob to prevent any leakage into the supporting furniture. This gasket guarantees a correct seal when used in conjunction with smooth work top surfaces.
• The safety gap between the hob and the cooker hood placed above must respect the indications of the hood manufacturer. In case of absence of instructions respect a distance minimum of 7650 mm.
• The connection cord should be subjected, after building, with no mechanical constraint, such for example of the fact of the drawer.
• WARNING: Use only hob guards designed by the manufacturer of the cooking appliance or indicated by the manufacturer of the appliance in the instructions for use as suitable or hob guards incorporated in the appliance. The use of inappropriate guards can cause accidents.
• A separation panel at least 20mm from the bottom of the cooktop must be included during installation to prevent access to the underside of the appliance. This panel can be made of any non-combustible rigid material. If the hob is going to be installed on the top of an oven, precautions must be taken to guarantee an installation in accordance with current accident prevention standards. Pay particular attention to the position of the electric cable: he must not touch any hot parts of the oven.

ELECTRICAL CONNECTION

• The installation of this appliance and the connection to the electrical network should be entrusted only to an electrician perfectly to the fact of the normative regulations and which respects them scrupulously.
• Protection against the parts under tension must be ensured after the building-in.
• The data of connection necessary are on the stickers place on the hob casing near the connection box.
• The connection to the main must be made using an earthed plug or via an omnipolar circuit-breaking device with a contact opening of at least 3 mm.
• The electrical circuit must be separated from the network by adapted devices, for example circuit breakers, fuses or contactors.

Caution!
This appliance has only to be connected to a network 230 V~ 50/60 Hz.
Connect always the earth wire.
Respect the connection diagram.
The connection box is located underneath at the back of the hob casing. To open the cover use a medium screwdriver. Place it in the slits and open the cover.

Connection of the hob
Setting up the configurations:
For the various kinds of connection, use the brass bridges which are in the box next to the terminal

Monophase 230V~1P+N
Put a bridge between terminals 1 and 2.
Attach the earth to the terminate “earth”, the neutral N to terminal 4, the Phase L to one of the terminals 1 or 2.
Biphase 400V~2P+N
Attach the earth to the terminate “earth”, the neutral N to terminal 4, the Phase L1 to terminals 1 and
the Phase L2 to the terminal 2.

Caution! Frequent loosening and screwing of the screws on the connection box risks damaging the efficiency of the tightness once screwed. It is therefore advisable to keep screwing and unscrewing to a minimum.
Ensure that the cables are correctly inserted and tightly screwed down.

We cannot be held responsible for any incident resulting from the incorrect connection or which could arise from the use of an appliance that has not been earthed or has been equipped with a faulty earth connection. 

WARRANTY CARD

Eurolinx Pty Limited A.B.N. 50 001 473 347 trading as ILVE (“ILVE”)
Office:
48-50 Moore Street, Leichhardt N.S.W 2040
Post:
Locked Bag 3000, Annandale, N.S.W 2038
P: 1300 856 411

WARRANTY REGISTRATION
Your ongoing satisfaction with your ILVE product is important to us. We ask that you complete the enclosed Warranty Registration Card and return it to us so that we have a record of the ILVE  product purchased by you, Alternatively, you can now register your warranty online at http://support.eurolinx.com.au/

PRIVACY
ILVE respects your privacy and is committed to handling your personal information in accordance with the National Privacy Principles and the Privacy Act 1988 (Cth). A copy of the ILVE Privacy Policy is available at www.ilve.com.au. ILVE will not disclose any personal information set out in the Warranty Registration Card (“Personal Information”) without your consent unless required by:

1.  law;
2. any ILVE related company;
3.  any service provider which provides services to ILVE or assists ILVE in providing services (including repair and warranty services) to customers. Our purpose in collecting the Personal Information is to keep a record of the ILVE product purchased by you, in order to provide better warranty service to you in the unlikely event that there is a problem with your ILVE product. ILVE may contact you at any one or more of the addresses, email addresses or telephone numbers set out in the Warranty Registration Card. Please contact ILVE on 1300 694 583 should you not wish to be contacted by I’VE.

WARRANTY

1.  Warranty
   ILVE warrants that each ILVE product will remain, for a period of twenty four (24) months computed from the date of purchase of the ILVE product, free from defects arising in the manufacture of the ILVE product (“Warranty”).
   Except for consumer guarantees set out in the Competition and Consumer Act 2010 (Cth) (“Act”), ILVE does not make any further warranties or representations in relation to ILVE products.
2.  What is not covered by the Warranty.
   The Warranty does not apply if an ILVE product is defective by a factor other than a defect arising in the manufacture of the ILVE product, including but not limited to:
   (a) damage through misuse (including failure to maintain, service or use with proper care), neglect, accident or ordinary wear and tear (including deterioration of parts and accessories and glass breakage);
   (b) use for the purpose for which the ILVE product was not sold or designed;
   (c) use or installation which is not in accordance with any specified instructions for use or installation;
   (d) use or operation after a defect has occurred or been discovered;
   (e) damage through freight, transportation or handling in transit (other than when ILVE is responsible);
   (f) damage through exposure to chemicals, dust, residues, excessive voltage, heat, atmospheric conditions or other forces or environmental factors outside the control or ILVE;
   (g) repair, modification or tampering by the purchaser or any person other than ILVE, an an employee of ILVE or an authorized ILVE service contractor*;
   (h) use of parts, components or accessories which have not been supplied or specifically approved by ILVE.
   (i) damage to surface coatings caused by cleaning or maintenance using products not recommended in the ILVE product handbook provided to the purchaser upon purchase of the ILVE product;
   (j) damage to the base of an electric oven due to items having been placed on the base of the oven the cavity or covering the base, such as aluminum foil (this impedes the transfer of heat from the element to the oven cavity and can result in irreparable damage); or
   (k) damages, dents or other cosmetic imperfections not affecting the performance of the ILVE in respect of an ILVE product purchased as a “factory second” or from the display The Warranty does not extend to light globes used in ILVE products.
3. Domestic Use
   Each ILVE product is made for domestic use. This Warranty may not extend to ILVE products used for commercial purposes.
4. Time for Claim under the Warranty
   You must make any claim under this Warranty within twenty-eight (28) days after the occurrence of an event which gives rise to a claim pursuant to the Warranty, by booking a service call on the telephone number below.
   Continued over…

   WARRANTY CARD CONTINUED

5. Proof of Purchase
   Customers must retain proof of purchase in order to be eligible to make a warranty claim in respect of an ILVE product.
6.  Claiming under the Warranty
   Customers will bear the cost of claiming under this Warranty unless ILVE determines the expenses are reasonable, in which case the customer must claim those expenses by providing written evidence of each expense to ILVE at the address on the Warranty Registration Card.
7. Statutory Rights
   (a) These terms and conditions do not afect your statutory rights.
   (b) The limitations on the Warranty set out in this document do not exclude or limit the application of the consumer guarantees set out in the Act or any other equivalent or corresponding legislation in the relevant jurisdiction where to do so would:
   (i) contravene the law of the relevant jurisdiction;  or
   (ii) cause any part of the Warranty to be void.
   (c) ILVE excludes indirect or consequential loss of any kind (including, without limitation, loss of use of the ILVE product) and (other than expressly provided for in these terms and conditions) subject to all terms, conditions and warranties implied by custom, the general law, the Act or other statute.
   (d) The liability of ILVE to you for a breach of any express or non-excludable implied term, condition or warranty is limited at the option of ILVE to:
   (i) replacing or repairing the defective part of the ILVE product;
   (ii) paying the cost of replacing or repairing the defective part of the ILVE product;
   (iii) replacing the ILVE product; or
   (iv) paying the cost of replacing the ILVE product.
   (e) Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
   You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
8. Defects
   Any part of an ILVE product deemed to be defective and replaced by ILVE is the property of ILVE. ILVE reserves the right to inspect and test ILVE products in order to determine the extent of any defect and the validity of a claim under the Warranty.
   *For your closest ILVE authorized service agent go to https://support.eurolinx.com.au/#/map/retailers
   All warranty service calls must be booked through ILVE’s Customer Care Centre on [email protected] or
   1300 85 64 11 option 1

Warranty Card tear off

WARRANTY REGISTRATION CARD
01032017

Please complete and send to ILVE at: REPLY PAID 83617
LEICHHARDT NSW 2040

Australia National Telephone Number 1300 MYILVE (694 583) New Zealand Telephone Number 0508 458 369 ILVE showrooms are open Tuesday – Friday: 9am-5pm and Saturdays 10 am-4 pm. Closed on Monday & Sunday

NSW & ACT (Head Ofice)
48-50 Moore Street
Leichhardt
F 02 8569 4699

VIC & SA
1211 Toorak Road
Camberwell
F 03 9809 2155

QLD
1/42 Cavendish Road
Coorparoo
F 07 3397 0850

WA & NT
Unit 10/55 Howe Street
Osborne Park
F 08 9201 9188

TAS (Crisp Ikin)
3 Pear Avenue
Derwent Park, 7009
P 03 6272 7386

New Zealand
PO Box 11.160
Sockburn Christchurch
F 03 344 5906

http://ilve.com.au
01012018

ILVE Built-In Electric Oven User Guidea

Introductions

ILVE’s new 900 Series large cavity ovens are the culmination of 2 years of research and development to bring Australian homes a oven that has the technology, sophistication and appearance that embodies the ILVE brand whilst having many functional advantages over its competitors.  Technology is at the forefront offering a new feature we call ‘CHEF-assist’. A colour,TFT touch screen with smart control panel available in 11 different languages, over 35 preset recipe modes and up to 100 saved ‘personalized’ recipes enable you to cook any dish for the entire family, perfectly. To make cooking even more enjoyable the latest range also offers automatic cooking times, weight presets and has the brilliant function of allowing you to change the thermostat from Degrees Celsius to Fahrenheit, making recipe temperature conversions and control easier than ever before. The new size of the cooking cavity provides more cooking space and maximizes the full internal size of the oven. Our new ULTRA-Clean light grey, nickel-free enamel interior reduces the toxicity of materials in contact with foods and is  easy to clean. Another new feature is the S-MOVE soft-closing door allows you to gently close the oven door with a simple push, preventing door impact; without using your hands, which are free to perform other tasks. Standard in the oven are Telescopic racks that are totally removable making the use of the ovens baking trays and general cooking in the oven easy and effortless. The Full size inner door glass provides a panoramic view from the outside of the oven door of what is inside the oven, its full width also enables easy cleaning with no crevices for food scraps and residue to get trapped.

ULTRA-Clean smooth grey cavity and Twin Fan Oven Cavity

900TCPGV with black Handle

S-move soft & gentle closing door hinges

Preset Cooking & Smart Touch Control Panel

• Twin fan heating providing even heat distribution with reduced hot spots and consistent heat
• PANA-View full-glass oven door and inner glass
• S-Move soft and gentle closing door hinges
• 11 different language settings
• Time (12h or 24h) and date setting
• Touch control TFT display with brightness adjustment
• Dark / black tinted glass on door exterior
• Pre programmable timer with 3 beeper level options
• Accurate digital thermostat control: 0°C-250°C
• Option for °C or °F setting
• Closed door grilling

SAFETY

• Cool touch BIO-Safe triple glazed glass door

FUNCTIONS

• Select 14 specialised manual expert modes
• CHEF-Assist with over 35 preset recipes with automatic cookingtime a nd weight preset for a variety of family meals
• Save up to 100 of your favoured most used recipes

CLEANING

• Select 14 specialised manual expert modes
• CHEF-Assist with over 35 preset recipes with automatic cooking time and weight preset for a variety of family meals
• Save up to 100 of your favoured most used recipes

CLEANING

• ULTRA-Clean smooth grey cavity
• Catalytic self cleaning liners
• Removable oven door and inner door glass

CAPACITY & INTERIOR

• Extra large 102 litre oven capacity
• 5 cooking levels

ACCESSORIES

• Standard with 1 x set of telescopic runners – with 75% extraction
• 2 x oven racks and 1 x grill pan (baking dish) set

For installation specifications, please consult with ILVE. For optimum installation, we recommend using the actual product as the best guide.

Follow us on:

Facebook.com/ILVEappliances 

 instagram.com/ILVE_appliances
youtube.com/ILVEappliances
BLOG livewithilvo.com

DISCLAIMER
Eurolinx PTY LTD, trading as ILVE Appliances, is continually seeking ways to improve the design specifications, aesthetics and production techniques of its products. As a result alterations to our products and designs take place continually. Whilst every effort is made to produce information and literature that is up to date, this brochure should not be regarded as an infallible guide to the current specifications, nor does it constitute an offer for the sale of any particular product. Product dimensions indicated in our literature is indicative only. Actual product only should be used to define dimension cutouts. Distributors, and retailers are not agents of ILVE Appliances and are not authorized to bind ILVE Appliances by any express or implied undertaking or representation.

Canopy Range Hood
IVG901/X1

Pictured: IVG901/X1 – 90cm Canopy Hood
ILVE’s range hoods are designed to stealthily keep your kitchen fresher and cleaner. ILVE range hoods craftily stand above the rest. Their powerful fan removes cooking odours, smoke and vapour from the kitchen, while extremely fine filters trap all grime. In-built LED Lights produce a natural brightness,  illuminating your cooking area while the streamlined electronic control panel ensures whisper-quiet air extraction is at your fingertips. Either as a visual focal point or discreetly integrated, it is easy to see that  ILVE range hoods are built to extract!

Model IVG901/X1

• 900 mm wide
• AS430 stainless steel
• 800m3/hr*
• 67 dBA (maximum)
• 3 speeds
• electronic push-button control
• blue indicator light
• 2 x LED lights
• 3 x 5-layer aluminium filters
• ducted only
• 50mm duct outlet**
• 220–240V/50Hz
• input power: 286W
• maximum motor power: 280W
• supplied with: 2 x 350mm flues & 2 x 500mm flues
• supplied with cord & plug

* Above Model
Type: Canopy Hood
Model: IVG901/ X1
Size: 90cm
Power standard: 10 Amp plug
Ducting size: 150mm

*Range Hood extraction rate m3/h reading is measured at: 1m duct up, 1 x 90°C bend & 1m vertical duct
**Using the conversion back to 125mm may affect performance

Australia National Telephone Number 1300 MYILVE (694 583) New Zealand Telephone Number 0508 458 369 ILVE showrooms are open Tuesday – Friday from 9am-5pm and Saturdays 10am-4pm. CLOSED Monday & Sunday

ilve.com.au

NSW & ACT (Head Office)
48-50 Moore Street
Leichhardt
F 02 8569 4699

DISCLAIMER
Eurolinx PTY LTD, trading as ILVE Appliances, is continually seeking ways to improve the design specifications, aesthetics and production techniques of its products. As a result alterations to our products and designs take place continually. Whilst every effort is made to produce information and literature that is up to date, this brochure should not be regarded as an infallible guide to the current specifications, nor does it constitute an offer for the sale of any particular product. Product dimensions indicated in our literature is indicative only. Actual products only should be used to define dimension cutouts. Distributors and retailers are not agents of ILVE Appliances and are not authorized to bind ILVE Appliances by any express or implied undertaking or representation.