Noctua NH-U9DX i4 Instruction Manual
Installation Manual
Dear customer,
Our DX line of coolers has become a default choice in high performance quiet cooling solutions for Intel Xeon CPUs and the latest i4 revision supports LGA2011 (both Square and Narrow ILM), LGA1356 and LGA1366 based Xeon platforms. Each Noctua product is double checked for flawless operation by our quality control team before it leaves the factory and I’m confident that you will be able to sense some of the research, attention and care we’ve put into making this product. Enjoy your NH-U9DX i4!
Yours sincerely,
Roland Mossig, Noctua CEO
This manual will guide you through the installation process of the SecuFirm2TM mounting system step by step. Prior to installing the cooler, please verify that the cooler is fully compatible with your motherboard. Should you encounter any difficulties, please check the FAQs on our website (www.noctua.at/faqs) and don’t hesitate to contact our support team at [email protected]. Noctua cannot be held responsible for any damage or losses caused by compatibility issues.
Warranty, Support and FAQs
Even with high-grade products and strict quality control, the possibility of defects cannot be eliminated entirely. Therefore, we aim at providing the highest possible level of reliability and convenience by offering a warranty period of 6 years and direct, fast and straightforward RMA service.
Should you encounter any problems with your Noctua cooler, please don’t hesitate to contact our support team (support@ noctua.at).
LGA2011
There are two different types of ILM (Independent Loading Mechanism) for Intel’s LGA2011 based Xeon CPUs: Square-ILM with 80x80mm hole spacing and Narrow-ILM with 56x94mm hole spacing.
Square ILM
If your mainboard uses a Square-ILM, please continue as described below. If your mainboard uses a Narrow-ILM, please refer to section LGA2011 Narrow-ILM.
LGA 2011 Square-ILM
Applying thermal paste
If there are residual traces of thermal paste or thermal pads on your CPU, please clean them off first. Then press a small drop (4-5mm diameter) of NT-H1 onto the centre of the heatspreader.
Caution:
Applying too much thermal paste will lower heat conductivity and cooling performance!
Fastening the heatsink to the CPU
Caution: Please first take off the fan as well as the protection cover at the bottom side of the heatsink.
Then put the heatsink onto the CPU and tighten the four springloaded screws until they stop using the supplied screwdriver.
Caution
Tighten the screws until they stop.
Attaching the fans
Re-attach the fans to the heatsink using the steel clips:
Please make sure that both fans are aligned in the same direction.
Connect the fans to the mainboard’s CPU fan header. Note that you can use the supplied y-cable (NA-YC1) to connect both fans to one CPU header.
Depending on your CPU and the temperature inside the case, you may interconnect the supplied NA-RC7 Low-Noise Adapters (L.N.A.) in order to further reduce the fans’ operating noise.
Caution:
Please use one adaptor per fan when running two fans with adaptors. Never use one adaptor for two fans by putting it before the y-cable.
Caution:
When using the L.N.A.s, check the temperature of your CPU using appropriate software (e.g. the respective applications of your mainboard manufacturer), in order to evade automatic throttling of the CPU due to the increased temperature. If the cooling performance is insufficient, please increase case ventilation or remove the L.N.A.s.
LGA2011 Narrow-ILM
Required mounting parts:
NM-XFB4 Standard Mounting Bar
NM-XFB5 90° Mounting Bar
The LGA2011 Narrow-ILM uses a different hole spacing than Square-ILM, so please replace the pre-installed Square-ILM mounting brackets (NM-XFB3) with Narrow-ILM brackets (NM-XFB4 or NM-XFB5) as described below.
This manual will guide you through the installation process step by step using the NM-XFB5 bracket as an example. Please note that the installation procedure is identical for NM-XFB5 and NM-XFB4.
First choose the appropriate set of Narrow-ILM mounting brackets according to the desired orientation of the cooler:
NM-XF4
NM-XFB5
Unscrew the preinstalled LGA2011 Square-ILM mounting brackets
(NM-XFB3) and take them off the heatsink.
Then remove the plastic lock-rings, springs and screws from the Square-ILM mounting brackets and put them into the Narrow-ILM mounting brackets.
After you’ve fixed the springs and screws to the appropriate Narrow-ILM fastening brackets, please screw the brackets to the heatsink:
NM-XFB4
NM-XFB5
LGA1356/1366
Required mounting parts:
NM-XBT2 Screws (black)
LGA1356/1366 uses a different thread than the pre-installed screws for LGA2011 (NM-XBT1), so please change the screws as described below.
Remove the plastic lock-rings, springs and screws (NM-XBT1) from the mounting brackets.
- NM-XBT1 (silver)
Then use the springs and the lock-rings to fix the black
LGA1356/1366 screws (NM-XBT2) to the mounting brackets. - NM-XBT2 (black)
After you’ve fixed the springs and screws to the mounting brackets, please proceed with the steps described in section LGA2011 Square-ILM.
]]>
www.noctua.at
sound-optimised premium components
Designed in Austria, Noctua’s premium cooling components are internationally renowned for their superb quietness, exceptional performance, and thoroughgoing quality. Having received more than 1000 awards and recommendations from leading hardware websites and magazines, Noctua’s fans and heatsinks are chosen by more than a hundred thousand satisfied customers around the globe. [email protected] | www.noctua.at
Dear customer,
Congratulations on choosing the Noctua NF-A8. Our fans are renowned for their impeccable quality and outstanding longevity and like all Noctua fans, the NF-A8 features an MTBF rating of more than 150.000 hours that’s backed up with our 6 years manufacturer’s warranty. Each Noctua fan is double checked for flawless operation by our quality control team before it leaves the factory and I’m confident that you will be able to sense some of the research, attention and care we’ve put into making this product.
Enjoy your NF-A8!
Yours sincerely,
Roland Mossig, Noctua CEO
This document includes some instructions for installing, running, and cleaning your NF-A8. Should you have any further questions, our support team ([email protected]) will be glad to assist you at any time.
Please also have a look at the regularly updated FAQs on our website: http://www.noctua.at/faqs
This document is also available in other languages at the following URL: http://www.noctua.at/manuals
http://mobile.noctua.at/manuals/fan/NF-A8_PWM/index.php
Scan this code to display multi-lingual manuals on your mobile phone:
NF-A8 PWM | User Manual
Installation
When installing the NF-A8 on a heatsink, radiator or other devices that use a custom mechanism for fan installation (fan clips, proprietary screws, etc.) please use this mechanism for installation.
When installing the NF-A8 as a case fan, you can either use proprietary clip systems (if your case features a clip system for fan installation) or the supplied mounting screws and silicone anti-vibration mounts. In order to install the fan using the silicone mounts, please first pull the silicone mounts through the mounting holes of the case. Then put the fan onto the silicone mounts and pull them through the mounting holes of the fan:
If necessary, you can easily remove the NF-A8’s integrated anti-vibration pads:
Connection
The NF-A8 comes with a 4-pin PWM fan connector for fully automatic speed control via your mainboard’s 4-pin PWM fan headers. Please note that the fan can also be connected to your mainboard’s 3-pin fan headers though. When connected to 3-pin fan headers, the NF-A8 will run at full speed (unless the mainboard supports voltage based speed control).
If you’re using multiple NF-A8 fans, you can use the supplied y-cable (NA-YC1) to connect several fans to one PWM fan header. This way, your mainboard will set all the connected fans to run at the same speed. The NF-A8 features a short 20cm primary cable in order to help you minimise cable clutter in typical applications. If you need a longer cable, please add the supplied 30cm extension (NA-EC1).
The NF-A8 comes with a Low-Noise Adaptor (NA-RC7) that allows you to reduce the fan speed from 2200 to 1750rpm. You can either use the adaptor to set the fan to a fixed speed of 1750rpm (if speed control is deactivated) or to cap the maximum speed to 1750rpm during PWM speed control.
Cleaning and Maintenance
Fans inside computer cases tend to accumulate dust over longer periods of usage. In order to maintain maximum performance, please clean your fans regularly using a duster, slightly moist tissue or canned air. Please be careful not to use too much force in order to prevent any damage to the fan. Please don’t use a vacuum cleaner as this may apply excessive force to the fan.
In order to ensure flawless operation over many years of usage, the NF-A8’s premium grade SSO2 bearing is fully sealed to prevent the entering of fine dust particles. Please note that the fan is not designed to be taken apart by the user. Removing the impeller from the frame will break the sealing of the bearing and results in a loss of warranty.
Warranty and Support
Even with high-grade products and strict quality control, the possibility of defects cannot be eliminated entirely. Therefore, we aim at providing the highest possible level of reliability and convenience by offering a warranty period of 6 years and direct, fast and straightforward RMA service.
Should you encounter any problems with your NF-A8, please don’t hesitate to contact our support team ([email protected]).
]]>