Rise and Shine Alarm Clock

Thank you for your purchase of this quality LCD Alarm Clock with LED backlight. Please read the instruction carefully and keep it in a safe place for future use.

1. SNOOZE key
2. ALARM ON/OFF switch
3. RESET hole
4. FUNCTION switch
5. oC/oF key
6. UP key
7. MODE key
8. DOWN key
9. BATTERY COMPARTMENT
10. BATTERY COVER

At first, open the BATTERY COVER (10) and insert 2 x ‘AAA’ size batteries into the BATTERY COMPARTMENT (9) as the polarity indicated, then close the BATTERY COVER (10).
Note: Do not mix new and old batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium) batteries.

FUNCTIONS

• Time and Calendar (including display of Month, Date and Day of the Week)
• Normal Alarm & Snooze Alarm
• Temperature (in selectable oC/oF format)

TIME AND CALENDAR SET

• Move the FUNCTION switch (4) to T.SET (TIME SET), hour part is blinking; press UP (6) or DOWN key (8) to set the hour. (Be careful to set AM or PM correctly. When the PM time is set under 12-hour mode, a ‘PM’ mark will be on display.)
• Press MODE key (7), minute part is blinking; press UP (6) or DOWN key (8) to set the minute.
• Press MODE key (7), year part is blinking; press UP (6) or DOWN key (8) to set the year (from 2002-2099).
• Press MODE key (7), month part is blinking; press UP (6) or DOWN key (8) to set the month.
• Press MODE key (7), date part is blinking; press UP (6) or DOWN key (8) to set the date.
• Move the FUNCTION switch (4) to NORMAL, the time and calendar settings are finished.

ALARM SET

• Move the FUNCTION switch (4) to AL.SET (ALARM SET), hour part is blinking; press UP (6) or DOWN key (8) to set the alarm hour. (Be careful to set AM or PM correctly.)
• Press MODE key (7), minute part is blinking; press UP (6) or DOWN key (8) to set the alarm minute.
• Press MODE key (7) again, the snooze interval minute is blinking; here you can set snooze interval from 1 to 60 minutes by pressing UP (6) or DOWN key (8). You can ignore this step; the default snooze interval is 1 minute.
• Move the FUNCTION switch (4) to NORMAL, the alarm setting is finished.

TURN THE NORMAL ALARM OR SNOOZE ALARM ON/OFF

• Normal Alarm:
  Move the ALARM ON/OFF switch (2) to AL.ON (ALARM ON), the clock will alarm lasting 1 minute only once when the set alarm time is up. (Press any key to stop alarm sound.)
• Snooze Alarm:
  Move the ALARM ON/OFF switch (2) to SNZ.ON (SNOOZE ON), the alarm sound will start when the set alarm time is up;
  a) Press SNOOZE key (1), the clock will stop alarm temporarily; the alarm sound will start again after the snooze interval ends. After doing so three times repeatedly, the snooze alarm function will stop working.
  b) If no button is pressed manually the alarm will last for 1 minute per every snooze interval (three times in total). After that, the snooze alarm function stops working.
  c) Press any key except of SNOOZE key (1), the snooze alarm function will stop working.
• Alarm off:
  Move the ALARM ON/OFF switch (2) to AL.OFF, the normal alarm or snooze alarm function will stop working.

TEMPERATURE DISPLAY

• Under normal state, press oC/oF key (5) to select Celsius or Fahrenheit on temperature display.

12/24 HOUR MODE

• Under normal state, press DOWN key (8) to select 12/24 hour mode.

RESET

• If the clock is dead (the display doesn’t work) during setting, please use a slim but blunt object (like ball pen pointer, toothpick etc.) to press RESET hole (3), then the clock will return to the initial mode.

BACKLIGHT

• Press SNOOZE key (1) on the top of the clock at any time, the backlight will be lightened.

MAINTENANCE

• The batteries should be replaced if the display screen or alarm becomes dysfunctional or weak.
• Please use a soft cloth or a paper towel to clean the clock.
• Do not use any corrosive cleanser or chemical solutions on the clock.

Thank you for your purchase!

IMPORTANT SAFETY INSTRUCTIONS:

• Please read all instructions carefully before assembling this bed.
• For your safety, assembly by two or more adults is strongly recommended.
• Keep these instructions for future use.
• Use only vendor-supplied hardware to assembly this item. Using unauthorized hardware could jeopardize the structural integrity of the item.

PRE- ASSEMBLY:

• Remove all parts and hardware from the box. Place them on a carpeted or scratch-free work surface, as this will avoid damaging parts. The shipping box provides an ideal work surface.
• To avoid accidentally discarding small parts or hardware, please do not dispose of any contents until assembly is complete.
• Two people are recommended for your safety and ease of assembly.
• Prior to starting this assembly, use the parts and hardware lists to identify and separate each of the pieces included.
• The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
• Note: Do not fully tighten any of the bolts until all parts are in place. Failure to follow these instructions may cause the bolts to misalign during assembly.
• Please use caution if using power tools to aid in assembly. Power tools can damage the hardware or split the wood.

PARTS INCLUDED:

(A) Headboard Panel – 1 x
(B) Footboard – 1 x
(C) Side Rail – 2 x
(D) Slat Roll – 1 x
(E) Left Headboard Post – 1 x
(F) Right Headboard Post – 1 x
(G) Stretcher – 1 x
(H) Bun feet – 4 x
(I) Finial – 4 x
(J) Support Rail – 1 x
(K) Support Leg – 3 x

HARDWARE INCLUDED:

TOOLS REQUIRED (NOT INCLUDED):

ASSEMBLY INSTRUCTION STEPS:

1. Put all furniture parts on a soft, scratch free surface such as a carpet or rug.
2. Attach the Headboard Panel (A) to the Left Headboard Post (E) and secure with 2 sets of: Bolt (L), Lock Washer (N), Half Moon Washer (P), and 2 Wooden Dowels 8x30mm (R), as seen in the illustration below.
3. Attach Stretcher (G) to the Left Headboard Post (E) and secure with 1 set of: Bolt (M), Lock Washer (N), Flat Washer (O), and 2 Wooden Dowels (R), as seen in the illustration below.
4. Tighten all bolts with Allen Key (Q).

5. Repeat steps # 2 – #4 to assemble the Right Headboard Post (F) to Headboard (A), as seen in the illustration below.

6. Thread the 4 Bun Feet (H) into the pre-fixed insert nuts found under the Headboard and Footboard Posts (A&B) in a clock-wise direction until tight, as seen in the illustration below.

7. Determine the desired location of bed and then hold the assembled Headboard (A) in a vertical position- tilted slightly forward.
8. Attach each Side Rail (C) to the Headboard (A) by inserting the hook (pre-attached at the ends of the Side Rail) into the corresponding slots of the Left & Right Headboard Post (E&F).
9. Push down firmly on the top of the Side Rails (C) until they sit themselves over the pins, inside the Post slots, as shown in the illustration below. Be sure the small ledge on each Side Rail (C) is facing inward.
10. Repeat steps #8 and #9 to assemble the Footboard (B), as seen in the illustration below.
There are two levels for the Side Rails (C). If you plan to use a trundle, please use the higher setting.

11. Place the Slats Roll (D) onto the opening, in-between the Side Rails (C), as seen below. Make sure the ends of the slats rest upon the small ledge inside of the Side rails (C).

12. Thread the 3 Support Legs (K) into the pre-drilled holes on the Support Rail (J), as seen in the illustration below.

13. Attach this assembled Support Rail (J) with Support Legs (K) to the underside of Slat Roll (D), as seen in the illustration below. NOTE: There are 3 possible positions for Support Rail (J). The center positions are used when not using trundle. If using a trundle, please follow steps #13 – #15 to assemble the Support Rail (J) and Support Leg (K) to the pre-drilled holes on the opposite side of the bed to where you desire the trundle to be used. This provides enough room for the trundle to not hit the Support Leg (K). See the 2 illustrations below.
14. Connect the 1st slat to the Support Rail (J) and secure with 1 set of: Bolt (M), Lock Washer (M), and Flat Washer (O) through the pre-drilled hole of the 1st slat and into the metal inserts located on the Support Rail (J).
15. Tighten with Allen Key (Q).
16. Repeat at the other end, as seen below.

17. Secure each Slat to the Side Rail (C) using 32 Round Head Screws (S) through the hole at the end of each slat and into the mattress support on the Side Rails (C), as seen in the illustration below.
18. To keep the whole bed level, adjust the levelers underneath each Support Leg (K), as seen in the illustration below.
19. Periodically tighten all connections.

20. Attach the 4 Finials (I) on top of each leg of the Headboard (A) and Footboard (B), as seen below.

CARE INSTRUCTIONS:

• Dust often using a clean, soft, dry, and lint-free cloth.
• Blot spills immediately and wipe with a clean, damp cloth.
• We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered finish.
• Hardware may loosen over time. Periodically check to make sure all connections are tight.
  Re-tighten if necessary.

SOPHIE QUEEN BED Manual Optimized

SOPHIE QUEEN BED Manual Original

References

• User Manual

PRE-ASSEMBLY:

• For your safety and ease, assembly by two adults is recommended.
• Please read all instructions before beginning assembly. The illustrations provided allow for easier assembly when
  used in conjunction with the assembly instructions.
• Remove all parts and hardware from box and lay out on a carpeted or scratch-free work surface. The shipping
  box provides and ideal work surface. Do not dispose of any contents until assembly is completed to avoid
  accidentally discarding small parts or hardware.
• Use the parts and hardware lists to identify and separate each of the pieces included prior to starting assembly.
• Note: DO not fully tighten the bolts until all parts are in place. Failure to follow these instructions may cause the
  bolts to misalign during assembly.
• Do not use power drill as it may cause cracking.

HARDWARE LIST

ASSEMBLY INSTRUCTIONS:

1. Slide a Spring Washer (D10) and a Flat Washer (D11) onto each Long/Short Bolts (D8 & D9).
2. Attach Support Rail (D6) to bottom of the Center Shelf (D2). Insert (4) Long Bolts (D) with washers from
   Support Rail (D6) into bottom of the Center Shelf (D2) by using Allen Key (D7). Note: Wooden cleat on the
   Support Rail (D6) is close to surface of Center Shelf (D2) after assembly.

3. Place Side Panel (D4) on a soft, scratch-free surface with bottom wooden blocks facing up. Attach (3) Shelf
(D1), Center Shelf (D2) and Bottom Shelf (D3) to Side Panel (D4) in sequence as shown below. Insert (2)
Shorts Bolts (D9) with washers from wooden cleat of each shelf into Side Panel (D4). Note: Wide apron of
Center Shelf (D2) and apron of Bottom Shelf (D3) face the edge without cut-out on bottom.

4. Place Cork Panel (D5) onto the assembled piece. Secure each shelf to Cork Panel (D5) by inserting (2) Short
Bolts (D9) with washers. Note: Cut-Out corner of the Side Panel and Corkboard Panel face each other.
Place the assembled bookcase in upright position. Check alignments and tighten all connecting bolts.

5. Assembly of Bookcase component completes.

CARE INSTRUCTIONS:

• Dust with a clean, soft cloth.
• Avoid the use of chemicals and harsh cleaning agents.

Sleep & Study Loft Bed – Bookcase Manual Optimized

Sleep & Study Loft Bed – Bookcase Manual Original

References

• User Manual

Emma Chandelier
Assembly and Installation Instructions
Country of Destination: US/CN UK/EU/AUS Middle East
CAUTION:

• BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
  Important Safety Instructions:
• These instructions are provided for your safety. It is very important that they are read carefully and completely before beginning the assembly and installation of this lighting fixture.
• We strongly recommend that a professional electrician install all direct wire fixtures.
• THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODES BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
• The lighting fixture is meant for indoor use. It must be connected only to 3-wire, single-phase electrical supply systems (provided with Ground wire or equivalent protection system).
• For your safety, it is strongly recommended that two people install the lighting fixture.
• This fixture has been rated for up to four (4) 40-watt maximum Type B standard (candelabra) incandescent light bulbs (not included) or four (4) 9-watt compact fluorescent light bulbs (not included). To avoid the risk of fire, do not exceed the recommended lamp wattage.
• Use with approved PBteen Shades only, having a minimum opening diameter of 3-1/2 inches and a minimum lamp-to-shade spacing of 2 inches.
• The lighting fixture is meant for indoor use, DRY LOCATIONS ONLY.
• Save these instructions.
  WARNING:
• To reduce the risk of fire, electrical shock or personal injury, always turn off and unplug the light fixture and allow it to cool prior to replacing the light bulb.
• Do not touch bulb when fixture is turned on. Do not look directly at lit bulb.
• Keep flammable materials away from lit bulb.
• This lighting fixture contains lead, a chemical know to the State of California to cause cancer, birth defects and other reproductive harm. Wash hands after installing, handling, cleaning or otherwise touching this light fixture.
  Pre-assembly:
• Remove all parts and hardware from box along with any plastic protective packaging.
• Do not discard any contents until after assembly is complete to avoid accidentally discarding small parts or hardware.
• For your safety, it is strongly recommended that two people install the lighting fixture.

Parts Included: Hardware Enclosed:
(1) Mounting Plate (D)            (3) Plastic Wire Nut Connectors (A)
(1) Threaded Tube (E)             (1) Green Ground Screw (B)
(1) Canopy (F)                          (2) Mounting Screws (C)
(1) Hanging Loop (G)              (4) Big Metal Balls (O)
(1) Canopy Nut (H)                  (1) Big Metal Ball (P)
(1) Lock Washer (I)                   (1) Small Metal Ball (Q)
(1) Hex Nut (J)
(2) Closable Link with Screw Cap (K/K1)
(1) Chain (L)
(1) Fixture Loop (M)
(4) Sockets (N)

TOOLS REQUIRED (not included): Ladder, Phillips Head & Flat Blade Screwdrivers, Wire Cutter/Stripper, Pliers &
Electrical Tape.

To Adjust the Suspension Length of the Fixture:

1. Note: The adjustment or shortening of the lighting fixture’s suspension length is only needed if the factory set chain
   length is not appropriate for your installation. We recommend that you adjust the chain to the proper desired length
   before cutting the electrical cord.
2. Determine the lighting fixture suspension length from the ceiling for the product installation, allowing the extra cord
   length for the outlet junction box wire connections as noted below.
3. Pull out the fixtures 2 wire power cord and bare ground wire woven through the Chain (L).
4. The chain length may be shortened from either end, if desired, by using pliers to separate a link along a split-line
   formed in each link. Use two pairs of pliers to gently pry the link apart so that a space is created large enough for the
   link to be removed from the remaining chain. Use a cloth or folded piece of paper between the pliers and the link to
   protect the finish of the link during bending. For longer lengths of chain to be removed, select the desired link from
   either end to open and remove the length of chain. Once the chain is at the desired length, reattach the chain (if it
   isn’t already) to the two Closable Links with Screw Caps (K) at each end of the chain. Secure each link by tightening
   the Closable Link Screw Cap (K1) (See Fig. 2). One Closable Link with Screw Cap (K) must be attached to both the
   Chain (L) and Fixture Loop (M) at the top of the Pendants Body and the other Closable Link with Screw Cap (K)
   must be securely attached to the other end of the Chain (L) and Hanging Loop (G).
5. Re-weave the fixtures 2 wire power cord and bare ground wire through every other loop to the top of Chain (L).
6. If needed, (depending upon final fixture hanging position from the ceiling), cut off the extra power cord length on the
   2 wire cord and bare ground wire. Make sure when cutting the power cord and bare ground wire to cut them so that
   they all are at least 6 inches (152.4 mm) long within the outlet junction box (J-box). Prepare the cut power cord wires
   using the following steps. Use wire strippers to prepare the ends of the two wires so that there is about 1/2 inch of
   exposed wire for the Plastic Wire Nut Connectors (A).

Assembly & Installation Instructions:

1. SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER!
2. Carefully unpack all fixture parts and hardware and lay them out on a clear workspace.
3. Unscrew the Closable Link Screw Cap (K1) from the lower Closable Link (K), and insert the bottom loop of Chain (L)
   and Fixture Loop (M) into the Closable Link (K). Tighten the Closable Link Screw Cap (K1) as shown in Fig. 2.
   4. If needed, weave the fixtures 2 wire power cord and bare ground wire through every other loop to the top of Chain
   (L).
4. Slip Canopy Nut (H) first and then position Canopy (F) over the upper end of Chain (L).
5. Unscrew the Closable Link Screw Cap (K1) from the upper Closable Link (K), and insert the top loop of Chain (L)
   and Hanging Loop (G) into the Closable Link (K). Tighten the Closable Link Screw Cap (K1) as shown in Fig. 2.
6. If the parts are not already preassembled, attach the Threaded Tube (E) into the threaded bore of the Hanging Loop
   (G) and rotate the Threaded Tube (E) clockwise until it is tightly engaged within the Hanging Loop (G). If the
   Threaded Tube (E) is not yet secured to the Mounting Plate (D), do so now so that a portion of the Threaded Tube (E)
   extends beyond the Mounting Plate (D).
7. Position the Lock Washer (I) first and then the Hex Nut (J) onto the extended upper portion of the Threaded Tube (E).
   Make sure the length of the Threaded Tube (E) is longer on the bottom end, as shown in Fig. 1. Tighten the Hex Nut
   (J) until tight using a hex wrench or a pair of pliers so that the Hanging Loop (G) is now firmly secured to the middle
   of the Mounting Plate (D).
8. Feed the fixtures 2 wire power cord and bare ground wire through to the Hanging Loop (G) and the Threaded Tube
   (E).
9. If needed, (depending upon final fixture hanging position from the ceiling), cut off the extra power cord length on the
   2 wire cord and bare ground wire. Make sure when cutting the power cord and bare ground wire to cut them so that
   they all are at least 6 inches (152.4 mm) long within the outlet junction box (J-box). Prepare the cut power cord wires
   using the following steps. Use wire strippers to prepare the ends of the two wires so that there is about 1/2 inch of
   exposed wire for the Plastic Wire Nut Connectors (A).
10. Gently pull existing wire down from the ceiling junction box and allow wires to hang. The HOT or LIVE wire is usually
    black. The NEUTRAL wire is usually white. Check to see if there is a ground wire that is usually green or green with
    a yellow stripe or exposed copper metal wire. If needed, use a pair of wire strippers to remove about 1/2 inch of
    insulation from each wire.
11. Carefully inspect the fixtures wires. The NEUTRAL FIXTURE WIRE has FINE LONGITUDINAL RIDGES running
    along its length. The HOT FIXTURE WIRE is SMOOTH and the BARE COPPER WIRE is the GROUND WIRE. If
    you have any doubt and cannot identify the power-supply wires with confidence, then we recommend that you ask
    an electrician and that you not continue with the installation.
12. With the help of another person to hold the weight of the fixture, attach the GROUND WIRE from the fixture to the
    GROUND JUNCTION BOX WIRE from the ceiling outlet junction box (J-box) (usually green insulation or bare wire).
    Fasten each together with a Plastic Wire Nut Connector (A) by twisting the connector in a clockwise direction and
    wrap the connection with electrical tape. Be sure that no wire strands are exposed. If your outlet junction box DOES
    NOT have a GROUND WIRE, be sure to insert the Green Ground Screw (B) into the Mounting Plate (D), marked as
    “GND”, facing downward and wrap the fixture’s bare ground wire around the Green Ground Screw (B). Tighten
    screw to clamp ground wire between ground screw head and Mounting Plate (D). IT IS IMPERATIVE THAT THE
    JUNCTION BOX IN YOUR HOME BE PROPERLY GROUNDED!
13. Connect the NEUTRAL FIXTURE WIRE to the NEUTRAL JUNCTION BOX WIRE (usually white insulation). Fasten
    each together with a Plastic Wire Nut Connector (A) by twisting the connector in a clockwise direction and wrap the
    connection with electrical tape.
14. Be sure that no wire strands are exposed.
15. Connect the HOT FIXTURE WIRE to the HOT JUNCTION BOX WIRE (usually black insulation). Fasten each together with a Plastic Wire Nut Connector (A) by twisting the connector in a clockwise direction and wrap the connection with electrical tape. Be sure that no wire strands are exposed. DO NOT REVERSE THE HOT ANDNEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
16. Check the wiring connections and if all looks good, gently tuck the wire connections neatly into the ceiling junction box.
17. Attach the Mounting Plate (D) to the ceiling outlet box using the 2 J-box Mounting Screws (C). Align the slots of the Mounting Plate (D) with the two threaded holes located on the J-Box. Use a screwdriver to tighten each screw until the Mounting Plate (D) is firmly secured to the J-Box.
18. Slide the Canopy (F) upward along the Chain (L) so that the central opening of the Canopy (F) is received and centered by the threaded portion of the Hanging Loop (G). A section of the threads on Hanging Loop (G) should be exposed below the Canopy (F). The Hanging Loop (G) should be hanging below the Canopy (F) and the upper rim of the Canopy (F) should be pressing gently against the ceiling surface, covering the junction box. While holding the Canopy (F) firmly in place, position the Canopy Nut (H) against the Hanging Loop (G) and rotate the nut clockwise to engage it with the threaded portion of the Hanging Loop (G) until secure. Do not over tighten this nut. Finger tight should be sufficient to hold the Canopy (F) firmly in place.
19. Attach each hook of the 4 Big Metal Balls (O) onto each loop at the bottom of each metal arm until secure (See diagram)
20. Attach the hook of the Big Metal Ball (P) onto the loop at the bottom of the light fixture until secure (See diagram)
21. Attach the hook of the Small Metal Ball (Q) onto the bottom loop of the Big Metal Ball (P) until secure (See diagram).
22. Insert four (4) 40-watt maximum Type B standard (candelabra) incandescent light bulbs (not included) or four (4) 9-watt compact fluorescent light bulbs (not included) into the Sockets (N). DO NOT EXCEED THE SPECIFIED WATTAGE.
23. Restore power to junction box and test fixture.
24. Assembly and Installation is complete.

Care instructions:

• Wipe clean with a soft, dry cloth or static duster.
• Always avoid the use of harsh chemicals or abrasive cleaners as they may cause damage to the fixture’s finish

Thank you for your purchase
Stores | catalog | www.pbteen.com
USA 1.866.472.4001

Emma Chandelier Manual Optimized

Emma Chandelier Manual Original

References

• User Manual

Important Safety Instructions:

• Please read all instructions carefully before assembling.
• For your safety, assembly by two or more adults is strongly recommended.
• DO NOT use your ball until you have read and understood this instruction/information in full. Keep these
  instructions for future use.
• Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the structural
  integrity of the item.
• Make sure the ball is at room temperature before proceeding. WARNING: Do not inflate when the
  temperature is lower than 65°F (18°C) or greater than 90°F (32°C).
• Never over-inflate your ball. The maximum diameter is 65 centimeters (approximately 26 inches). Over inflation
  of the ball may compromise its integrity and performance.
• The ball is NOT a toy and should be kept out of reach of children.
• Avoid exposing ball to rough, sharp or abrasive surfaces, DO NOT kick or hit the ball.
• Avoid exposing the ball to excessive sunlight or heat, such as heaters, lamps, fireplaces, etc.
• We DO NOT recommend the ball as a fitness ball. DO NOT take the ball out of the fabric cushion.

Pre-assembly:

• Remove all parts and hardware from the box and lay out on a clear carpeted or scratch-free work surface, as
  this will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
• Do not dispose of any packaging or contents of the shipping carton until assembly is completed to avoid
  accidentally discarding small parts or hardware.
• Use the parts and hardware lists below to identify and separate each of the pieces included.
• The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
• Use manual Pump only. Do not use compressor to pump the ball.

Parts Included:
(A) Ball and Cushion 1pc
(B) Base 1pc

Tools Included:

Assembly Instruction Steps:
1. Remove cap from the pump air nozzle. Insert the adapter to the nozzle as shown.

2. Insert the adapter into the hole of ball and hold firmly with one hand. Inflate ball until it is 80% of its maximum
size or about 55 centimeters.

4. Remove pump adapter from ball and immediately insert ball plug into hole until the top is even with the ball..
Then zip up. It is recommended you let the ball sit for at least one hour to allow material to adapt to the
expansion before inflating fully.

5. After waiting the recommended time, remove the ball plug and immediately insert the pump adapter with pump
back into the ball. Repeat steps 1&2 until ball is inflated to optimum size (65 cm). Reinsert Plug when complete.
To remove Plug from ball, slip u-shaped Plug Remover underneath the Plug and lift.

6. Place the ball cushion on base.

Care Instructions:

• Dust often using a clean, soft, dry and lint-free cloth.
• We do not recommend the use of chemical cleansers, abrasives or furniture polish on our lacquered finish.
• It is not necessary to deflate ball after use, however, slight leakage may occur over time. Re-inflate as
  necessary. Periodically pump the ball to maintain ball in 65cm diameter.

Exercise Ball [Desk] Chair Manual Optimized

Exercise Ball [Desk] Chair Manual Original

References

• User Manual