RocketFish 40″ to 75″ TV Wall Mount – Full Motion [RF-HTLF23] User Manual

RocketFish 40″ to 75″ TV Wall Mount – Full Motion [RF-HTLF23] User Manual

Introduction

Congratulations on your purchase of a high-quality Rocketfish product. Your
RF-HTLF23 represents the state of the art in TV wall-mount design and is designed for reliable and trouble-free performance.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

• This product is designed ONLY to be installed into wood studs, solid concrete, or concrete block.
• DO NOT INSTALL INTO DRYWALL ALONE — DRYWALL ALONE WILL NOT HOLD THE WEIGHT OF YOUR TV.
• This product is designed for INDOOR USE ONLY.
• The wall must be capable of supporting five times the weight of the TV and mount combined.
• Do not use this product for any purpose not explicitly specified by manufacturer.
• Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
• Improper installation may cause property damage or personal injury. If you do not understand these directions, or have doubts about the safety of the installation, contact Customer Service or call a qualified contractor. Rocketfish is not responsible for damage or injury caused by incorrect installation or use.
• The weight of your TV and accessories must not exceed 100 lbs. (45.3 kg).
• This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children!

Specifications

• Maximum TV weight: 100 lbs. (45.3 kg)
• Screen size: From 40 in. to 75 in. (101.6 cm to 190.5 cm) diagonal
• Overall dimensions (H × W): 17.7 × 25.1 in. (45 cm × 63.9 cm)
• Wall-mount weight: 18.8 lbs. (8.5 kg)
• For customer service, call: 1-800-620-2790

Dimensions

Tools needed

You need the following tools to assemble your new TV wall mount:

Package contents

Make sure that you have all the hardware necessary to assemble your new TV wall mount:

TV HardwareConcrete Installation Kit CMK1 (not included)

Contact customer service at 1-800-359-5520 to have these additional parts shipped directly to you.

Installation instructions

STEP 1 – Determine whether your TV has a flat back or an irregular or obstructed back

1. Carefully place your TV face-down on a cushioned, clean surface to protect the screen from damage and scratches.
2. If your TV has a tabletop stand attached, remove the stand. See the documentation that came with your TV for instructions.
3. Temporarily lay the horizontal brackets (04) on the back of your TV.
4. Align the screw holes in the brackets with the mounting screw holes on your TV.
5. Identify which type of back your TV has:
   • Flat back: The brackets lay flush against the back of your TV and do not block any jacks. You do not need spacers when assembling the wall mount.
   • Obstructed back: The brackets block any of the jacks on the back of your TV. You need 2.5 mm or 22 mm spacers (03) when assembling the wall mount.
   • Irregularly-shaped back: There is a gap between the brackets and some part of the back of your TV. You need 2.5 mm or 22 mm spacers (03) when assembling the wall mount.
6. Remove the brackets.

STEP 2 – Select screws, washers, and spacers

1. Select the hardware for your TV (screws, washers, and spacers). A limited number of TVs come with mounting hardware included. (If screws came with your TV, they are almost always in the holes on the back of your TV.) If you don’t know the correct length of the mounting screws your TV requires, test various sizes by hand threading the screws.
   Select the screws that fit:
   • M6 × 12 mm screws (01)
   • M6 × 35 mm screws (01)
   • M8 × 16 mm screws (01)
   • M8 × 25 mm screws (01)
   • M8 × 35 mm screws (01)
   • M8 × 50 mm screws (01)
     Use the M6/M8 washers (02) for all screws.
     For an irregular or obstructed TV back, also use the 2.5 mm or 22 mm spacers (03).
     CAUTION: To avoid potential personal injuries and property damage, make sure that the screws have adequate threads to secure the brackets to your TV. If you encounter resistance, stop immediately and contact customer service. Use the shortest screw and spacer combination to accommodate your TV. Using hardware that is too long may damage your TV. However, using a screw that is too short may cause your TV to fall from the mount.
2. Remove the screws.
3. For a flat back TV, go to STEP 3 – Option 1: Attaching the horizontal brackets to a TV with a flat back on page 10.
   -OR-
   For an irregular or obstructed back, go to STEP 3 – Option 2: Attaching the horizontal brackets to a TV with irregular or obstructed back on page 11.

STEP 3 – Option 1: Attaching the horizontal brackets to a TV with a flat back

CAUTION: To avoid personal injury or property damage, do not use power tools.

1. Align the holes you noted on the horizontal brackets (04) with the screw holes on the back of your TV.
2. Place the washers (02) over the holes in the brackets that align with the screw holes on the back of your TV, then insert the screws that you selected in STEP 2 (01) through the washers. Make sure that the brackets are level.
3. Tighten the screws until they are snug against the brackets. Do not over-tighten.

STEP 3 – Option 2: Attaching the horizontal brackets to a TV with an irregular or obstructed back
CAUTION: To avoid personal injury or property damage, do not use power tools.

1. Place the spacers you selected in STEP 2 (03) over the screw holes on the back of your TV.
2. Align the horizontal brackets (04) over the spacers, then place the washers (02) over the holes in the brackets. Insert the screws you selected in STEP 2 (01) through the washers, brackets, and spacers. Make sure that the brackets are level.
3. Tighten the screws until they are snug against the brackets. Do not over-tighten.

STEP 4 – Attaching the vertical bracket
CAUTION: To avoid personal injury or property damage, do not use power tools.

1. Lay the vertical bracket (05) on top of the horizontal brackets (04). Make sure that the bracket is centered.
2. Secure the vertical bracket to the horizontal brackets with the TV interface screws (06). Tighten the screws until they are snug against the vertical brackets. Do not over tighten.

STEP 5 – Determine wall-mount location

Note: Your TV should be high enough so your eyes are level with the middle of the screen from a seated position (normally, 40 to 60 inches from the ground).
For more detailed information on determining where to drill your holes, visit our online height-finder at: http://mf1.bestbuy.selectionassistant.com/index.php/heightfinder

The center of your TV will match the center of the wall plate (08). Before you drill holes in the wall:

1. Measure the distance from the bottom of your TV to the middle of the four mounting screw holes. This is measurement a.
2. Measure the distance from the floor to where you want the bottom of your TV to be placed on the wall. Keep in mind that the bottom of your TV should be placed above any furniture (such as entertainment centers or TV stands). Your TV should also be above items placed on top of the furniture (like a Blu-ray player or cable box). This is measurement b.
3. Adda + b. The total measurement is the height where you want the center of the wall plate (08) to be on the wall.
4. Use a pencil to mark this spot on the wall.

STEP 6 – Option 1: Installing on a wood stud wall
Note: Drywall covering the wall must not exceed 5/8″ (16 mm).

1. Locate the stud, then verify the center of the stud with an edge-to-edge stud finder.
2. Make sure that the distance between the studs is 16 in. (40.6 cm).
   Note:
   Drywall covering the wall must not exceed 5/8 in. (1.6 cm). Minimum wood stud size: nominal 2 × 4 in. (5.1 × 10.2 cm) actual 1 1/2 × 3 1/2 in. (3.8 × 8.9 cm).
3. Align the center of the wall plate template (07) at the height you determined in the previous step and make sure that it is level. Tape the template to the wall.
4. Drill four pilot holes through the template to a depth of 2 3/4 in. (7 cm) using a 7/32 in. (5.5 mm) diameter drill bit, then remove the template.
5. Align the wall plate (08) with the pilot holes, insert the lag screws (09) through washers (10) and into the holes in the wall plate, then tighten the lag screws only until they are firm against the wall plate assembly.
   CAUTION: Avoid potential injuries or property damage! DO NOT over-tighten the lag screws (09).

STEP 6 – Option 2: Installing on a solid concrete or concrete block wall

CAUTION: To prevent property damage or personal injury, never drill into the mortar between the blocks. Mount the wall plate directly onto the concrete surface.

1. Align the center of the wall plate template (07) at the height you determined in the previous step and make sure that it is level. Tape the template to the wall.Note: Mount the wall plate (08) directly onto the concrete surface (no wall covering).
   Minimum solid concrete thickness: 8in. (20.3 cm).
   Minimum concrete block size:
   8 × 8 × 16 in. (20.3 × 20.3 × 40.6 cm).
   Minimum horizontal space between fasteners:
   16 in. (40.6 cm).
   For concrete applications, the arm assembly (11) must remain centered in wall plate (08). Keep this in mind when selecting the wall plate location.
2. Drill pilot holes to a depth of 3 in. (7.6 cm) using a 3/8 in. (10 mm) diameter masonry drill bit, then remove the template.
3. Insert the concrete wall anchors (C3) (see Concrete Installation Kit CMK1 (not included) on page 7) into the pilot holes and use a hammer to make sure that the anchors are flush with the concrete surface.
4. Align the wall plate (08) with the anchors, insert the lag screws (C1) through the washers (C2) and into the holes in the wall plate assembly, then tighten the lag screws only until they are firm against the wall plate.
   CAUTION: Avoid potential injuries or property damage! DO NOT over-tighten the lag screws (C1).

STEP 7 – Attach the arm assembly to the wall plate

1. Hang th earm (11) onto the wall plate (08) by first hooking the top of the arm assembly into the wall plate channel, then lowering the bottom of the assembly into place.
2. Use the hex key (14) to secure the arm assembly to the wall plate (08) with the wall plate screws (13).
   CAUTION: These wall plate screws must be installed to secure your TV onto the wall plate assembly.

STEP 8 – Attach your TV to the arm assembly

1. Hang your TV onto the arm assembly (11) by first hooking the top support of the vertical bracket (05) onto the assembly, then resting your TV into place. You hear an audible click when your TV is in place.
2. Use the hex key (14) to lock your TV to the arm assembly with the locking screw (12).
   IMPORTANT: The locking screw must be installed to secure your TV onto the arm assembly.

STEP 9 – Managing cables

• Fully extend the arm assembly (11) to provide enough slack, then routing cables along the arms and inserting them into the channels on the arms to provide a clean look to your installation.

STEP 10 – Adjust tilt

Note: After your TV is in place, tighten the tilt tension knob to prevent unwanted movement.

Loosen the tension knob with your fingers or the hex key (14), adjust the tilt angle, then tighten the knob to keep your TV in place.

STEP 10 – Adjust the level

1. Loosen the locking screw (12).
2. Turn the leveling screw (L) with a Phillips screwdriver to level your TV.
3. Retighten the screw (12).

Removing your TV from the wall mount

1. Disconnect all cables, then pull down the release cord located below the vertical bracket to unlock your TV from the vertical bracket.
2. Use the hex key (14)to remove the locking screw (12) from the arm assembly (see STEP 8 – Attach your TV to the arm assembly on page 22).
3. Lift your TV off the arm assembly.

For customer service, call: 1-800-620-2790 (U.S. and Canada)

LIFETIME LIMITED WARRANTY

Definitions:
The Distributor* of Rocketfish branded products warrants to you, the original purchaser of this new Rocketfish-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”).
For this warranty to apply, your Product must be purchased in the United States or Canada from a Best Buy branded retail store or online at www.bestbuy.com or www.bestbuy.ca and is packaged with this warranty statement.

How long does the coverage last?
The Warranty Period lasts for the useful life of the Product beginning on the date you purchased the Product. Your purchase date is printed on the receipt you received with the Product. In the event the Distributor ceases to sell the covered Rocketfish-branded product, this Limited Lifetime Warranty shall terminate for that product and there shall be no repair or replacement of the Product.

What does this warranty cover?
During the Warranty Period, if the original manufacture of the material or workmanship of the Product is determined to be defective by an authorized Rocketfish repair center or store personnel, Rocketfish will (at its sole option): (1) repair the Product with new or rebuilt parts; or (2) replace the Product at no charge with new or rebuilt comparable products or parts. Products and parts replaced under this warranty become the property of Rocketfish and are not returned to you. If service of Products or parts are required after the Warranty Period expires, you must pay all labor and parts charges. This warranty lasts as long as you own your Rocketfish Product during the Warranty Period. Warranty coverage terminates if you sell or otherwise transfer the Product.

How to obtain warranty service?
If you purchased the Product at a Best Buy retail store location or from a Best Buy online website
(www.bestbuy.com or www.bestbuy.ca), please take your original receipt and the Product to any Best Buy store. Make sure that you place the Product in its original packaging or packaging that provides the same amount of protection as the original packaging.
To obtain warranty service, in the United States and Canada call 1-800-620-2790. Call agents may diagnose and correct the issue over the phone.

Where is the warranty valid?
This warranty is valid only in the United States and Canada at Best Buy branded retail stores or websites to the original purchaser of the product in the country where the original purchase was made.

What does the warranty not cover?
This warranty does not cover:

• Customer instruction/education
• Installation
• Set up adjustments
• Cosmetic damage
• Damage due to weather, lightning, and other acts of God, such as power surges
• Accidental damage
• Misuse
• Abuse
• Negligence
• Commercial purposes/use, including but not limited to use in a place of business or in communal areas of a multiple dwelling condominium or apartment complex, or
• otherwise used in a place of other than a private home.
• Unauthorized modification of any part of the Product, including the antenna
• Display panel damaged by static (non-moving) images applied for lengthy periods (burn-in).
• Damage due to incorrect operation or maintenance
• Connection to an incorrect voltage or power supply
• Attempted repair by any person not authorized by Rocketfish to service the Product
• Products sold “as is” or “with all faults”
• Consumables, including but not limited to batteries (i.e. AA, AAA, C etc.)
• Products, where the factory applied serial number, has been altered or removed
• Loss or Theft of this product or any part of the product
• Display panels containing up to three (3) pixel failures (dots that are dark or incorrectly illuminated) grouped in an area smaller than one-tenth (1/10) of the display size or up to five (5) pixel failures throughout the display. (Pixel-based displays may contain a limited number of pixels that may not function normally.)
• Failures or Damage caused by any contact including but not limited to liquids, gels or pastes.

REPAIR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR EXCLUSIVE REMEDY FOR BREACH OF WARRANTY. ROCKETFISH SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, INCLUDING, BUT NOT LIMITED TO, LOST DATA, LOSS OF USE OF YOUR PRODUCT, LOST BUSINESS OR LOST PROFITS. ROCKETFISH PRODUCTS MAKES NO OTHER EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THE WARRANTY PERIOD. SOME STATES, PROVINCES AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.
Contact Rocketfish:
1-800 620-2790
www.rocketfishproducts.com
Rocketfish is a trademark of Best Buy and its affiliated companies.
*Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2019 Best Buy. All rights reserved.
Made in China

FAQS

Does this particular mount attach on one stud or two?

This attaches to two studs. Two lags in each stud.

when pressed flat against the wall, what is the depth from the wall?

it is 2 1/2″ out

My houses studs are 24″ apart, this big enough for that?

Yes, that will work

Can you mount this outside?

Yes you can, its all made of metal and you are putting a TV or Screen on it meaning no water is going to directly hit the metal, however is coated with black paint, it won’t rust.

Does this work on 24” studs?

Yes

does this fits for tv with 83 inch which weigh 93 pound & 400×400 vesa?

This mount is rated for to up 100 lbs and a tv up to 75″.

Does arm assembly have to in the exact center of wall plate?

No

Does it work with 55″ roku tv?

Yes it should work. It fits any flat-screen TV between 40″-75″.

Can this be mounted on a brick fireplace?

If you have the right mounting hardware it can be mounted on brick or in a stone surface

It says this is for 40″ – 75″ tvs. will this fit a 39″ tv or is it too big?

Yes it will fit once is VESA

Can this lock in place?

It does NOT lock in place, but it stays in place wherever it’s placed. Very good quality.

Will this work for a Samsung 50″ TV?

Yes it will….quite easily in fact.

Can I install my TV on a concrete wall?

Yes, as long as it is a solid concrete wall. Do not install on drywall alone.

Can I install my TV on a brick wall?

Yes, as long as it is a solid brick wall. Do not install on drywall alone.

Can I install this mount to a wood stud?

Yes, as long as the wood studs are at least 2″ x 4″ or larger.

Can I use this mount with an articulating arm?

No, this mount is not compatible with articulating arms.

How much weight can a rocketfish TV mount hold?

Up to 100 lbs. for sturdy support.

Does rocketfish TV mount work with Samsung?

Yes, the mount is compatible with a 50″ Samsung TV.

Is rocketfish VESA compliant?

Universal for high-quality mounting up to 700×400. *To obtain additional screws for your product, please call 1-800-620-2790.

Should a wall mounted TV be tilted?

A wall-mounted TV should only be tilted when glare from room lights or nearby windows creates a problem viewing the screen. If there are no problems with room reflections and the TV is installed at eye level, there should be no need to tilt the screen.

What is the best wall mount for a 75 inch TV?

The overall best TV mount for 75-inch TVs is the USX Mount Full-Motion TV Wall Mount. The amount of value you get from this mount compared to its price is unparalleled. It achieves a small footprint while providing the widest range of motion.

Can you hang a 75 inch TV on the wall?

The answer to this is yes, you can mount your XL TV on the wall. Safety is paramount, of course.

How high do you mount a TV?

The common rule is that a 42” TV should be mounted about 56 inches from the floor to the center of the TV, a 55” should be 61 inches, a 65” should be 65, and a 70” should be 67 inches from the floor to the middle of the TV. As you can see, the larger the television, the higher it should be hung.

Why is my TV mount crooked?

Additionally, you will want to make sure the wall does not have a slant or have some crooked parts to it. Surprisingly, there are many times little items, such as a loose bolt, will cause a TV to be crooked.

VIDEO

www.rocketfishproducts.com

Rocketfish RF-WRSK18/ RF-WRSK18-C Wireless Rear Speaker Kit

FEATURES

• 2.4 GHz wireless sender and wireless receiver
• Transmits high quality audio over a radio
  frequency communication link
• Compact size
• Hidden antennas
• Low power consumption

Wireless sender

Front view

Back View

Bottom View

Wireless receiver

Font View

Bottom View

Back view

SETTING UP YOUR WIRELESS REAR SPEAKER KIT

CONNECTING THE WIRELESS SENDER TO YOUR HOME THEATER RECEIVER

Home theater receiver back panel

Caution: Turn off your home theater receiver while connecting the speaker kit.

1. Using the included two-foot speaker cords, connect the right rear speaker terminals of your home theater receiver to the right speaker terminals of the wireless sender by connecting the red wire to the red (+) terminals, and the black wire to the black (-) terminals.
2. Connect the left rear speaker terminals of the home theater receiver the same way.

CONNECTING THE WIRELESS RECEIVER TO YOUR REAR SPEAKERS

1. Connect the right speaker to the right speaker terminals of the wireless receiver, and the left speaker to the left speaker terminals.
2. If the speaker wires are attached to the speakers already, connect the positive (+) wire from the right speaker to the red (+) terminal for the right speaker on the wireless receiver and the negative (-) wire from the right speaker to the black (-) terminal for the right speaker on the wireless receiver.
3. Connect the left speaker the same way.

CONNECTING THE WIRELESS SENDER AND WIRELESS RECEIVER TO A POWER OUTLET

To connect the wireless sender to the power adapter:

1. Plug the DC power cord from the 5V DC power adapter into the DC 5V jack on the wireless sender.
2. Plug the 5V DC power adapter into a power outlet.

Caution: To avoid risk of fire, and to prevent damage, only use the power adapters supplied with your wireless rear speaker kit.

To connect the wireless receiver to a power outlet:

Note: Plug the power cord in only after all speakers are connected to the wireless receiver.

1. Plug the small (female) end of the power cord into the AC input of the 18V DC power adapter.
2. Plug the DC power cord from the power adapter into the DC 18V jack on the wireless receiver.
3. Plug the large (male) end of the power cord into a power outlet.
   

USING YOUR UNIVERSAL WIRELESS REAR SPEAKERKIT

To turn on the system:

• Turn on the power switch on the back panel of both the wireless sender and wireless receiver. The LED indicator blinks to indicate that the devices are plugged in.
  
  Establishing communications between the wireless sender and wireless receiver
• If the front panel LEDs light solid on both units, a link has been established. If the front panel LEDs are blinking on one or both units, do the following:

1. Press and hold the CONNECT button on either the wireless sender or wireless receiver for two seconds to enter connection mode. (While in “connection mode,” the LED indicators blink at a faster rate.)
   
2. Within 30 seconds, press the CONNECT button on the other unit so it will enter connection mode. A link will be established automatically and the LED indicators will light solid.
   Note: If the LED indicators keep blinking after 30 seconds, try pressing the CONNECT buttons again.

LISTENING TO THE SYSTEM

1. Turn on the system. Make sure that there is an active link between the wireless sender and wireless receiver.
2. Turn on your home theater receiver, then play the audio or video source through your home theater receiver.

The volume control on the wireless receiver is only used to adjust the balance of the volume between the front and rear speakers. After the system is set up, we recommend that you adjust the volume balance one time.

TROUBLESHOOTING

LEGAL NOTICES

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

IC Statement

CAN ICES-3 (B)/NMB-3 (B)

ONE-YEAR LIMITED WARRANTY

Visit www.rocketfishproducts.com for details

CONTACT ROCKETFISH:

For customer service please call 1-800-620-2790 www.rocketfishproducts.com

ROCKETFISH is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC. 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2019 Best Buy. All rights reserved. Made in China

Rocketfish RF-HTS3117 12-outlet Surge Protector

PACKAGE CONTENTS

• 12-outlet surge protector
• Quick Setup Guide

FEATURES

• Protects equipment from damaging power surges and spikes.
• Firestop design advanced MOVs with built-in fuses minimize fire hazards from major power surges.
• Incorporates noise filtering to reduce EMI/RFI interference and provide “clean” power that will maximize the performance of your equipment.
• Twelve AC outlets provide continuous AC power.
• Six AC adapter spaced outlets accommodate bulky AC adapter plugs.
• Main power switch/circuit breaker controls power to all AC outlets on the surge protector, and allows the unit to be reset after a circuit overload has resolved.
• Two USB charging or power ports, 2.1A total charge current, for fast charging of smartphones, tablets, or other devices.
• Protected LED indicator lights when the surge protection feature is working properly.
  Note: If this LED does not light or goes out, the surge protection feature has reached full capacity and can no longer absorb additional surges and spikes. The surge protector should be replaced if this light goes out.
• Grounded LED indicator lights when a properly grounded AC outlet is detected.
  Note: If this LED does not light, we recommend that you contact a certified, licensed electrician to inspect your wiring.
• 6 ft (1.8 m) Soft-Flex™ power cord with right-angle/off-set plug enables placement of the surge protector in the desired location. The right-angle plug allows you to  place furniture as close as possible to the wall and not block the second AC outlet.
• Data line surge protection protects your incoming RJ11 (phone) or RJ45 (Ethernet) line from surges and spikes. Compatible with Gigabit Ethernet
• Coaxial cable surge protection protects two sets of your incoming coaxial cable lines from surges and spikes.

USING YOUR SURGE PROTECTOR

1. Plug the surge protector’s power cord into a standard 120V AC outlet. If the LEDs do not light up, press the main power switch/circuit breaker on the front of the unit.
2. Plug the power cords from up to twelve devices into the AC outlets on the surge protector.
3. Plug your USB devices into the USB ports to power or charge them.
4. Plug in Ethernet or telephone cables to the data line surge protection ports. Be sure to follow the correct direction for INPUT (what is coming out of the wall or from the modem) and OUTPUT (what is going to a cable box or Blu‐ray player). An additional Ethernet or telephone cable is required (not included).
5. Plug in a coax cable from cable TV, satellite TV, or for your cable Internet connection. Two sets are provided. Either one can be used if only one device is being connected. Be sure to follow the correct direction for INPUT (what is coming from the wall) and OUTPUT (what is going to a cable box or TV). An additional
   coax cable is required (not included).

SPECIFICATIONS

SAFETY PRECAUTIONS

• RISK OF ELECTRIC SHOCK – Use only in dry locations and only indoors.
• DO NOT plug into another extension cord or power strip.
• DO NOT plug surge protectors into other surge protectors.
• DO NOT use with any aquarium equipment.
• DO NOT use if correctly grounded outlets are not available.
• DO NOT install this device if there is not at least 30 feet (10 meters) or more of wire between the electrical outlet and the electrical service panel.
• This device features internal protection that will disconnect the surge protective component at the end of its useful life, but will maintain power to the load
  – WHICH WILL BE UNPROTECTED. If you don’t want your equipment at risk, follow the manufacturer’s instructions for replacing the device.

LEGAL NOTICES

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

ONE-YEAR LIMITED PRODUCT WARRANTY

See included warranty sheet, visit www.rocketfishproducts.com, or call 800-620-2790 for additional connected equipment and product warranty information or for customer service.

CONTACT ROCKETFISH

For customer service, call 1-800-620-2790
www.rocketfishproducts.com

ROCKETFISH is a trademark of Best Buy and its affiliated companies.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2016 Best Buy. All rights

Rocketfish RF-HG100F18,100 ft Fiber Optic HDMI Cable

FEATURES

• Supports up to 4K Ultra HD (4096 × 2160) resolution to get the very best picture from your 4K source
• High Dynamic Range (HDR) support to significantly increase the range of both color and contrast which creates an even
more vibrant and realistic picture
• Latest generation chipset and fiber optic cabling results in the best performance
• Fiber optic cable design allows for lossless transmission of high-bandwidth video and audio over extremely long lengths
• Micro USB power inputs available for supplemental power insertion in challenging installations. The need for supplemental power is uncommon, and it should only be required if no image displays or image problems occur. Micro USB cables and power supplies are not included.

SETTING UP YOUR HDMI CABLE

CAUTION: Do not bend the cable sharply (less than a .8 inch radius).

1. Plug the Source end of your HDMI cable into the source device (such as a Blu-ray player, cable/satellite box, or receiver).
2. Plug the Display end of your HDMI cable into the display (such as a TV, monitor, or projector).

Notes:

• Your HDMI cable is directional. If you do not plug the correct end into the correct device, it will not work. Each end of your HDMI cable is labeled on the connector and with a yellow sticker.
• If your HDMI cable is plugged in correctly and does not work properly, your HDMI cable may need supplemental power. Plug a micro USB cable (not included) into the micro USB port on each end of your HDMI cable, then connect the micro USB cables to power.

TROUBLESHOOTING

• My display shows a black screen.
  Make sure that each end of your HDMI cable is plugged into the correct device. If your HDMI cable is plugged in correctly, plug a micro USB cable (not included) into the micro USB port on each end of your HDMI cable, then connect the micro USB cables to power.
• The audio or video cuts in and out.
  Make sure that each end of your HDMI is plugged in fully and your cable is not bent.
• My display shows static.
  Make sure that you did not use an adapter or converter with your HDMI cable. If you did, remove the adapter or converter from your HDMI cable, then plug your HDMI cable directly into the source device or display.
• My display does not show 4K content.
  Make sure that all of your devices support 4K. You need a source device and a display that support 4K resolutions and 4K content on your source device.

Before using your new product, please read these instructions to prevent any damage

SPECIFICATIONS

• Cable length: 100 ft. (30.5 m)
• Cable diameter: .2 in. (5.2 mm)
• Cable bending radius: 0.8 in. (20 mm)
• Operating temperature: 32-131° F (0-55° C)
• Storage temperature: -4-176° F (-20-80° C)
• Interface: HDMI A Male to HDMI A Male
• HDMI version: 2.0 (backwards compatible with all previous HDMI versions)
• Maximum resolution: 4K (4096 × 2160 or 3840 × 2160) at 30 or 60Hz (YUV4:2:0 4K@60Hz; YUV4:4:4 4K@30Hz)
• Full 3D support: Yes
• Bandwidth speed: 18 Gbps
• Audio specifications: 32 uncompressed audio channels; 1536kHz sample rates
  Note: This product does not support Audio Return Channel (ARC).
  This will not affect most users and does not degrade the signal quality.
• Other specifications: HDCP 2.2; EDID; CEC
• In-wall Installation: UL Certified, CL2

IMPORTANT SAFETY INFORMATION

• Read these instructions.
• Never pull on the cable to disconnect the connector end from a source or display.
• Do not bend your HDMI cable too far. The bending radius at any point on your HDMI cable must be more than .8 in. (20 mm).
• Do not expose your HDMI cable to water.
• Do not use excessive force when installing your HDMI cable.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that produce heat.
• Do not store your HDMI cable in an extremely cold, warm, or humid environment.
• Do not dismantle your HDMI cable.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, maybe cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  ICES statement: CAN ICES-3 B/NMB-3 B

FIVE-YEAR LIMITED WARRANTY

Visit www.rocketfishproducts.com for details

CONTACT ROCKETFISH

For customer service, call 1-800-620-2790 (U.S. and Canada) or 01-800-926-3010 (Mexico)
www.rocketfishproducts.com

ROCKETFISH is a trademark of Best Buy and its affiliated companies.
Registered in some countries. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2017 Best Buy. All rights reserved.
Made in China

RF-G1501 / RF-G1501-C, 4-Port HDMI Switch with 4K Compatibility

PACKAGE CONTENTS

• 4-Port HDMI Switch
• Remote control
• Power adapter
• Quick Setup Guide

FEATURES

Your 4-Port HDMI Switch supports 4K video and next-generation audio.

• Compatibility with most CEC-enabled HDMI devices
• Resolution – 480p, 720p, 1080p, and 4K (4096 × 2160)
• Frame Rate – Up to 4k at 60 Hz (1080p at 120 Hz)*
• Color – Deep Color, HDR, and other enhanced color specifications
• Audio – Works with Dolby TrueHD, DTS-HD, and all audio formats supported by the HDMI 2.0 standard
• Auto Switch – When a source device is turned on, the switch automatically detects and switches to that device’s input
  *Note: TVs with high internal refresh rates (such as 240 Hz) are compatible. The specifications refer to source signal and not TV refresh rate.

SETTING UP YOUR HDMI SWITCH

1. Connect HDMI cables from your source devices to the switch’s INPUT ports.
2. Connect an HDMI cable from your TV (or projector) to the switch’s OUTPUT port.
3. Connect the power adapter from the DC 5V port to a power outlet.

The power LED and an input LED light up.
Note: To fully support 4K resolution, connect the input and output channels using HDMI PREMIUM Certified cables (within 3 meters).

Optional wall-mounting: Install two screws 4 in. (10.2 cm) apart into your wall, then hang the switch on the screws. Mounting hardware is not included.

USING YOUR HDMI SWITCH

1. Turn on your TV and source device.
2. To turn on your switch press POWER ON/OFF on your remote control or tap the (power) symbol on your switch.
   Note: When the switch is turned on, it automatically switches to the last input that was used.
3. To select a source device:
   • Press the number on your remote that matches the input of the source device you want.
   OR
   • Tap the number on your switch that matches the input your source device is connected to The corresponding input LED lights.
4. Use your source device as usual to play video and audio.
5. When finished, press and hold (power) to turn off your switch. Before using your new product, please read these instructions to prevent any damage.

Note: You may leave the power on while not in use.

SETTING UP THE AUTO SWITCH FUNCTION

Note: The auto switch function setting is on by default.

• You can turn the auto switch function off or back on by pressing and holding the POWER button on the front panel for three seconds while the switch is turned off.
• The LEDs on the front panel flash twice to indicate that the auto switch function is turned off.
• The LEDs on the front panel turn on for two seconds to indicate that the auto switch is turned on.

Note: Some devices don’t output an on/off detection signal to activate the auto switch function on your switch. If this causes signal confusion, turn off the auto switch function.

REPLACING THE REMOTE BATTERY

1. Push in the tab on the battery tray, then pull out the tray.
2. Remove the old battery. Insert a new CR2025 battery with the + facing up, then slide the tray closed.

TROUBLESHOOTING

No video and/or audio

• Make sure that all connections are correct and secure.
• Make sure that the switch is plugged in and turned on.
• Make sure that the switch is set to the correct source device.
• Make sure that your TV (or projector) is set to the input/source that your switch is connected to.
• Make sure that the audio and video formats (such as a Blu-ray disc) are supported by the source device and display that you are using.
• Unplug the switch’s power cable, wait 10 seconds, then plug it back in again.
• Make sure that your TV or projector supports the video resolution that your source device is using.
• Make sure that your HDMI cable is not damaged. Try connecting a different HDMI cable.
• Long HDMI cables may cause signal loss. Try a different, shorter HDMI cable.
• Higher resolution settings require higher quality HDMI cables. Try using lower resolution settings if you are using standard HDMI cables (within 3 meters).
• To fully support 4K resolution, connect the input and output channels using HDMI PREMIUM Certified cables.

Input source will not change

If you are changing the source with the switch:

• Press more firmly and touch the button longer.
• Make sure that you are not wearing gloves and that your fingers are clean and dry.
• Try changing the source with a remote. If you are changing the source with a remote:
• Move closer to the switch and make sure that there is a line of sight between the switch and remote sensors.
• Replace your remote control’s battery.
• Try changing the source with the controls on the switch.

Notes:

• When the CEC function fails, confirm whether your source and sink devices support CEC.
• When CEC malfunctions cause screen output abnormalities, turn off the CEC function of your source or sink devices.

SPECIFICATIONS

Dimensions (H ×W × D):1.02 × 3.4 × 6.9 in. (2.6 × 8.6 × 17.5 cm )
Weight: 0.66 lbs. (0.3 kg)
Power supply with micro USB connector: 5V DC/0.6A

LEGAL NOTICES

FCC Statement

1. FCC Caution – §15.21:
   “Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.”
2. FCC Statement – §15.105(b):
   This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
   • Reorient or relocate the receiving antenna.
   • Increase the separation between the equipment and receiver.
   • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
   • Consult the dealer or an experienced radio/TV technician for help.
3. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.

ONE-YEAR LIMITED WARRANTY

Visit www.rocketfishproducts.com for details.

CONTACT ROCKETFISH:

For customer service, call 1-800-620-2790 (U.S. and Canada) or 01-800-926-3010 (Mexico) www.rocketfishproducts.com

ROCKETFISH is a trademark of Best Buy and its affiliated companies.
Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2020 Best Buy. All rights reserved.