Model: ZV210N

1. General Information

These instructions should be read carefully in full prior to installation, and retained for further reference and maintenance.

2. Safety

• Before installation or maintenance, ensure the mains supply to the light switch is switched off and the circuit supply fuses are removed or the circuit breaker turned off.
• It is recommended that a qualified electrician is consulted or used for the installation of this light switch and install in accordance with the current IEE wiring and Building Regulations.
• Check that the total load on the circuit including when this light switch is fitted does not exceed the rating of the circuit cable, fuse or circuit breaker.

3. Technical Specifications

• Mains Supply: 230V AC 50 Hz
• Battery: 9V DC battery supplied (replaceable).
• 2 wire connection: No neutral required
• This light switch is of class II construction and must not be earthed
• Switch Type: Single or Two way
• Switch Rating:
  2000W Incandescent/Halogen,
  250W Fluorescent
  (Low-loss or Electronic Ballast),
  250W CFL (Electronic Ballast),
  400W LED Lighting
  (PF 0.9 or higher).
• Minimum Depth of Wall Box: 25mm
• Operating Temperature: 0°C to +40°C
• Mounting Height: 1.1m for optimum detection range
• On-time Adjustment: 0, 2, 4, 6, 8 hours or D (Dusk until Dawn).
• LUX Adjustment: 1 ~10lux (Moon symbol) to 300lux (Sun symbol)
• Front Cover: Conceals On-time/LUX adjustments and battery compartment, with retaining screw
• Manual ON/OFF Switch
• Low Battery Indication: The LED will pulse 1 sec ON, 8 secs OFF
• CE Compliant
• Dimensions – H=86mm, W= 86mm, D=29.5mm

4. Installation

Note: The installation of this light switch should be protected by suitable circuit protection of up to 10A rating.

4.1 Ensure the mains supply is switched off and the circuit supply fused are removed or the circuit breaker is turned off, until you have completed the installation.

4.2 Loosen the retaining screw located on the bottom of the light switch, and open the hinged front cover that conceals the battery holder and On-time/Lux adjusters. (Fig. 3)

4.3 Fit the 9V battery (supplied) maintaining the correct polarity. (Fig. 4)

4.4 Remove the existing light switch, and transfer the wires to the ZV210N (See section 5.Connection Diagram).

4.5 Secure the unit to the back box with the fixing screws provided, forming the cables during installation to avoid any entrapment and cable damage.

5. Connection Diagram

6. Testing

• Ensure that the light switch is in the OFF position.
• Turn the Lux Adjustment, which is located beneath the front cover on the right hand side of the light switch, fully anti clockwise to the Moon symbol.
• Turn the On-time Adjustment, which is located beneath the front cover on the right hand side of the light switch, clockwise to the 2 hour mark
• Emulate darkness by covering the Light Sensor (make sure the Light Sensor is fully covered, use black insulation/PVC tape if needs be).
• The lamp will automatically turn ON.
• After 3 seconds, uncover the Light Sensor.
• The lamp will turn off after it’s set period 2, 4, 6 or 8 hours or until dawn.
• To revert to a normal light switch, turn the On-time Adjustment 5 fully anti-clockwise to the 0 hour mark.

7. Setting Up For Automatic Operation

• Ensure the light switch is in the OFF position.
• Turn the Lux Adjustment fully anti-clockwise to the Moon symbol.
• Turn the On-time Adjustment to the desired setting (2, 4, 6, 8 Hours or D for Dawn).
• When the ambient light level reaches the level of darkness at which you wish the lamp to become operative (i.e. at dusk) SLOWLY rotate the lux adjustment control in a clockwise direction until a point is reached where the lamp illuminates.
• Leave the Lux Adjustment set at this point.
• At this position, the unit should become operative at approximately the same level of darkness each evening.

Note: If you wish to use unit as a normal light switch, turn the On-time Adjustment fully anti-clockwise to the 0 hour mark. If you wish to use the Automatic feature again, please follow the above instructions.

Adjustments

• If you find that your lights switch on when it is too dark, turn the Lux Adjustment clockwise towards the Sun symbol.
• If the light is in operation when it is too light turn the Lux Adjustment towards the Moon symbol.

Notes:

• The ZV210N light switch has a built-in delay function to ensure that momentary changes in the light do not switch it ON.
• The hours shown on the dial are only approximate guides, do not expect great accuracy.
• Once the switch has turned ON and the programme has turned OFF after the required number of hours, it is important not to allow artificial light to fall on it, followed by a period of darkness. This will fool the switch into thinking it is dark again and it will operate. Care should therefore be taken to prevent light falling onto the switch, e.g. table lamps.

8. Low Battery Warning

• When the 9V battery is running low, the RED LED will pulse 1 second ON, 8 seconds OFF, as warning and indication to change it (See section 4. Installation, step 4.2 & 4.3 for how to access the battery compartment).

9. Support

Note: If you have any concerns that the intended application of this product does not meet your requirements, please contact Timeguard directly prior to installation.

3 Year Guarantee

In the unlikely event of this product becoming faulty due to defective material or manufacture within 3 years of the date of purchase, please return it to your supplier in the first year with proof of purchase and it will be replaced free of charge. For the second and third years or any difficulty in the first year telephone the helpline on 020 8450 0515.

Note: A proof of purchase is required in all cases. For all eligible replacements (where agreed by Timeguard) the customer is responsible for all shipping/postage charges outside of the UK. All shipping costs are to be paid in advance before a replacement is sent out.

If you experience problems, do not immediately return the unit to the store.
Telephone the Timeguard Customer Helpline:

HELPLINE
020 8450 0515

or email [email protected]

Qualified Customer Support Coordinators will be online to assist in resolving your query.

For a product brochure please contact:

Timeguard Limited.
Victory Park, 400 Edgware Road,
London NW2 6ND
Sales Office: 020 8452 1112
or email [email protected]

www.timeguard.com

67.058.653 (Issue 2)
TG50572 – January 2020

Installation & Operating Instructions

10W Round LED Wall/Ceiling Light with Microwave Sensor
Model: LEDMR10WHMS3K

1. General Information

These instructions should be read carefully and retained for further reference and maintenance.

2. Safety

• Before installation or maintenance, ensure the mains supply to the luminaire is switched off and the circuit supply fuses are removed or the circuit breaker turned off.
• It is recommended that a qualified electrician is consulted or used for the installation of this luminaire and install in accordance with the current IEE wiring and Building Regulations.
• Check that the total load on the circuit including when this luminaire is fitted does not exceed the rating of the circuit cable, fuse or circuit breaker.

3. Technical Specifications

• 230V AC 50 Hz
• This luminaire is of class II construction and must not be earthed · 10W LED Non-replaceable lamp
• Energy efficiency: Class A+
• Energy Usage: 10kWh/1000H
• Lumen Output: 800lm
• Colour Temperature: 3000K
• Transmission Power: <0.2mW
• Working Frequency: 5.8GHz
• Standby Power Consumption: 0.9W approx.
• Detection Angle: 360°
• Adjustable Detection Range: 1 to 8m (radius)
• Adjustable Time Delay: 10 seconds to 30 minutes
• Dusk Level Adjustment: 10 to 2000 Lux
• IP44 Rated suitable for restricted external applications
• Operating Temperature: -15°C to +45°C
• CE Compliant
• EC Directives: Conforms to latest directives
• Dimensions: 180mm Diameter x 55mm
• Mounting Hole Centres: 134mm

Note: The high-frequency output of this sensor is <0.2mW, that is just one 5000th of the transmission power of a mobile phone or the output of a microwave oven.

4. Selecting a Location

• Careful positioning of the sensor will be required to ensure optimum performance (See diagram A & B).
• The best all-around coverage is achieved with the unit mounted at the optimum height of 2.5 metres.
• During extreme weather conditions the microwave sensor may exhibit unusual behaviour. This does not indicate a fault with the sensor. Once normal weather conditions return, the sensor will resume normal operation.

Warning: The product will not operate normally if there is any metal material in front of the installation location.

5. Installation

• Ensure the mains supply is switched off and the circuit supply fuses are removed or the circuit breaker turned off.
• An isolating switch should be installed to the switch the power ON and OFF to the luminaire. This allows the unit to be easily switched OFF for maintenance purposes.
• Remove the diffuser from the base by turning 45 degrees anti-clockwise and pulling away from the base of the luminaire.
• Select a suitable cable entry point either provided or by drilling into the base ensuring not damage or infringe on any of the internal components.
• Mark the position of the mounting holes on the wall or ceiling.
• Drill the holes for the wall plugs ensuring not to infringe with any gas/water pipes or electrical cables that may be hidden below the surface.
• Secure the230V AC 50Hz mains supply cable into the luminaire through the hole(s) provided ensuring that a cable gland, grommet or sealing compound is used to maintain the IP rating of the luminaire.
• Fix the luminaire using the correct screws for the wall plugs installed.
• Terminate the cable into the terminal block (See section 6. Connection Diagram below) ensuring correct polarity is observed and that all bare conductors are sleeved.
• Set the microwave sensor adjustments i.e. TIME, LUX and SENS using a thin flat blade screwdriver (See section 7. Setting Up).
• Reposition the lens over the luminaire and twist clockwise to close.
  

6. Connection Diagram

• Connect the 230V AC 50Hz mains supply to the terminals as marked below;
  
  Live Supply (Brown or Red) to L
  Neutral Supply (Blue or Black) to N

7. Setting Up

• Take note of the 3 adjusters located beneath the diffuser/lens;
  
• By default the 3 adjusters will be set as follows in order for you to complete a full walk test (from powering the unit ON for the first time);

TIME – fully anticlockwise to its minimum (approx. 10 seconds time delay).
LUX – fully clockwise to its minimum (full day and night time operation).
SENS – fully clockwise to its maximum (maximum detection range).

5 Walk Test Procedure

• Turn the power to the unit ON. The lamp will immediately illuminate for approximately 2 seconds and then will extinguish. This indicates the unit is wired correctly.
• The unit will now operate during daytime as well as at night, illuminating the lamp for approx. 10 seconds each time. This allows testing to be carried out to establish whether the sensor is covering the required area.
• Walk across the location the luminaire is fitted, to establish the detection area.
• With sensitivity set to the maximum, the sensor will detect you within an approximately 8 metre radius from the centre of the luminaire location with a 2.5 metre ceiling mounting height.
• As you cross the detection “zone” the lamp will illuminate. Now stand still until the lamp extinguishes (this should take approx. 10 seconds).
• Start moving again after 4 seconds. As you cross the detection zone the lamp will illuminate.
• Repeat the above, walking at various distances and angles to the unit to confirm the detection pattern.

Setting Up for Automatic Operation

• With the walk tests complete, the luminaire can be set up for automatic operation.
• Use a thin flat blade screwdriver to make the adjustments.

TIME ­ Time ON Delay Setting

• The TIME setting controls how long the unit remains illuminated following activation and after all motion ceases.
• The luminaire can be set to stay ON for any period of time between approx. 10 seconds (dial turned fully anti-clockwise) to approx. 30 minutes (dial turned fully clockwise)
• Any movement detected during the ON period will instantly reset the timer.
• The LED indicator located above the three adjusters will flash when adjusting the ON time delay;

1 flashes – 10 seconds (minimum time delay),
2 flashes –  1 minute,
4 flashes – 2 minutes,
3 flashes – 5 minutes,
5 flashes – 8 minutes,
6 flashes – 10 minutes,
7 flashes – 15 minutes,
8 flashes – 20 minutes,
9 flashes – 25 minutes,
10 flashes – 30 minutes (maximum time delay).

Note: After the light switches OFF, it takes approx. 4 seconds before it is able to start detecting movement again. The light will only switch ON in response to movement once this period has elapsed.

LUX ­ Light Control Setting

• The LUX control determines the level of darkness required for the unit to start operating.
• Turn it fully anti-clockwise to select full dusk until timed OFF operation (approx. 10 Lux).
• Turn it fully clockwise to select full daytime until timed OFF operation (approx. 2000 Lux).
• The setting is best achieved in real time by following the procedure below;

1. Set the LUX control knob fully clockwise.
2. When the ambient light level reaches the level of darkness at which you wish the lamp to become operative (i.e. at dusk) SLOWLY rotate the control in an anti-clockwise direction until a point is reached where the lamp illuminates.
3. Leave the control set at this point.

• At this position the unit should become operative at approximately the same level of darkness each evening.
• Observe the operation of the unit. If the unit is starting to operate too early (i.e. when it is quite light) adjust the control slightly anti-clockwise. If the unit starts to operate too late (i.e. when it is very dark). Adjust the control slightly clockwise.
• Continue to adjust until the unit operates as desired.
  

SENS ­ Detection Range Setting

• The SENS control setting determines the range of detection produced with the luminaire mounted at an optimum height of 2.5 metres.
• Turn it fully anti-clockwise to select the minimum detection range of approx. 1 metre radius.
• Turn it fully clockwise to select the maximum detection range of approx. 8 metres radius.

8. Troubleshooting

Problem

• The luminaire will not switch ON
• The luminaire is permanently ON
• The luminaire

Solution
Check the LUX light control setting is not set in the wrong position according to the current light level. Adjusting the setting (fully clockwise for day and night operation) and test again. Make sure the mains supply is connected correctly (See section 6. Connection Diagram) and switched ON. The luminaire could be faulty, replace the light fitting.

There is continuous movement within the detection zone. Reduce the SENS and TIME control setting to the minimum and test again.

Make sure the unit is mounted securely so it does activates without any not move. noticeable movement Ensure that there is no movement that is not identified i.e. behind a wall or the movement of a small object in the immediate vicinity, if so reduce the SENS control setting and test again.

3 Year Guarantee

In the unlikely event of this product becoming faulty due to defective material or manufacture within 3 years of the date of purchase, please return it to your supplier in the first year with proof of purchase and it will be replaced free of charge. For years 2 and 3 or any difficulty in the first year, telephone the helpline on 020 8450 0515. Note: A proof of purchase is required in all cases. For all eligible replacements (where agreed by Timeguard) the customer is responsible for all shipping/postage charges outside of the UK. All shipping costs are to be paid in advance before a replacement is sent.

Note: If you have any concerns that the intended application of this product does not meet your requirements, please contact

Timeguard directly prior to installation. If you experience problems, do not immediately return the unit
to the store. Telephone the Timeguard Customer Helpline;

HELPLINE
020 8450 0515
or email [email protected]
Qualified Customer Support Co-ordinators will be on-line to assist in resolving your query.
For a product brochure please contact:
Timeguard Limited. Victory Park, 400 Edgware Road,
London NW2 6ND Sales Office: 020 8452 1112 or email [email protected]
w w w.timeguard.com
67.058.666 (Issue 1)

TG43932 ­ June 2019

General Information

These instructions should be read carefully in full prior to installation, and retained for further reference and maintenance.

Safety

• Before installation or maintenance, ensure the mains supply to the light switch is switched off and the circuit supply fuses are removed or the circuit breaker turned off.
• It is recommended that a qualified electrician is consulted or used for the installation of this light switch and install in accordance with the current IEE wiring and Building Regulations.
• Check that the total load on the circuit including when this light switch is fitted does not exceed the rating of the circuit cable, fuse or circuit breaker.

Technical Specifications

• Mains Supply: 230V AC 50 Hz
• Battery: 9V DC battery supplied (replaceable).
• 2 wire connection: No neutral required
• This light switch is of class II construction and must not be earthed
• Switch Type: Single or Two way
• Switch Rating: 2000W Incandescent/Halogen,
  250W Fluorescent (Low-loss or Electronic Ballast),
  250W CFL (Electronic Ballast),
  400W LED Lighting (PF 0.9 or higher).
• Minimum Depth of Wall Box: 25mm
• Operating Temperature: 0°C to +40°C
• Mounting Height: 1.1m for optimum detection range
• Detection Angle: 170°
• Detection Range: 8m Front, 4m Sides
• Time ON Adjustment: 10 seconds (Min) to 15 minutes (Max)
• LUX Adjustment: 1 ~10lux (Moon symbol) to 1000lux (Sun symbol)
• Front Cover: Conceals Time/LUX adjustments and battery holder, with retaining screw
• Slide Switch: For Automatic and Manual ON/OFF selection
• DIP Switch: To enable or disable the Manual ON/OFF function.
• Motion Indication: Red LED turns ON for 1 second when motion detected
• Low Battery Indication: RED LED pulses 1 sec ON, 8 secs OFF
• CE Compliant
• Dimensions – H=86mm, W= 86mm, D=29.5mm

Selecting a Location

• For indoor use only i.e.: hallways, dining-room, basement, utility rooms and garages, etc. To replace existing one or two way light switches.
• Since the ZV810N is sensitive to temperature changes.
  Avoid mounting directly above heat sources or exposed to direct sunlight.
• Avoid mounting the motion sensor switch where it can come into contact with water or rain.
• For best results mount the sensor switch to detect objects moving across it.

Coverage

• The ZV810N can be mounted at heights between 0.85m to 1.5m.
  The optimum height for detection is 1.1m, which we recommend to achieve the 8m range. Please note that that mounting it any higher will not give the same performance.

Installation

Note: The installation of this light switch should be protected by suitable circuit protection of up to 10A rating.

5.1 Ensure the mains supply is switched off and the circuit supply fused are removed or the circuit breaker is turned off, until you have completed the installation.
5.2 Loosen the retaining screw located on the bottom of the light switch, and open the hinged front cover that conceals the battery holder and On-time/Lux adjusters.

5.3 Fit the 9V battery (supplied) maintaining the correct polarity.

5.4 Remove the existing light switch, and transfer the wires to the ZV810N (See section 6.Connection Diagram).
5.5 Secure the unit to the back box with the fixing screws provided, forming the cables during installation to avoid any entrapment and cable damage.

Connection Diagram

DIP Switch and Slide Switch

Note: The DIP Switch located on the back of the light switch can be used to enable or disable the Manual ON/OFF function, when using the Slide Switch. By default this will be set ON.

• If the DIP Switch is set to the ON (upwards) position, the Slide Switch can be used to turn your lights ON/OFF manually, or can be set to AUTO for motion control only.
• If the DIP Switch is set to the opposite (downwards) position, the Slide Switch will be disabled and your lights will turn ON using motion only.

Walk Test

Note: If the DIP Switch is set to the ON position, also make sure the Slide Switch is set to the AUTO (middle) position.

• Set the On-time adjuster fully anticlockwise to the min 10s position.
• Set the Lux adjuster fully clockwise to the SUN symbol.
• The light switch will now operate during the daytime as well as at night, illuminating your lights for approx. 10 seconds each time. This allows testing to be carried out to establish whether the sensor is covering the required area.
• Walk in front and around the sensor to establish the detection area. The sensor will detect motion within an 8m diameter (walking across), and within a 3m range (walking towards) with the sensor mounted at 1.1m.
• As you cross the detection ‘zone’ your lights will illuminate.
  Now stand still until your lights extinguish (this should take approx. 10 seconds).
• Start moving again after 2 seconds until your lights turn ON.
• Repeat the above, walking at various distances and angles from the light switch. This will help you confirm the detection pattern.

Setting up for Automatic Operation

• Turn the Lux Adjustment fully anti-clockwise to the Moon symbol.
• Turn the On-time Adjustment to the desired setting (10 seconds Minimum to 15 minutes Maximum).
• When the ambient light level reaches the level of darkness at which you wish the lamp to become operative once motion is detected (i.e. at dusk) SLOWLY rotate the control in an clockwise direction, whilst moving (e.g. your hand) in front of the sensor, until a point is reached where the lamp illuminates.
• Leave the Lux Adjustment set at this point.
• At this position, the unit should become operative at approximately the same level of darkness each evening each time motion is detected.

Adjustments

• If you find that your lights switch on when it is too dark, turn the Lux Adjustment clockwise towards the Sun symbol.
• If the light is in operation when it is too light, turn the Lux Adjustment towards the Moon symbol.

Low Battery Warning

• When the 9V battery is running low, the Motion Indication Red LED will pulse 1 second ON, 8 seconds OFF, as warning to change it (See section 5. Installation, step 5.2 & 5.3 for how to access the battery compartment).

Support

Note: If you have any concerns that the intended application of this product does not meet your requirements, please contact Timeguard directly prior to installation.

3 Year Guarantee

In the unlikely event of this product becoming faulty due to defective material or manufacture within 3 years of the date of purchase, please return it to your supplier in the first year with proof of purchase and it will be replaced free of charge. For the second and third years or any difficulty in the first year telephone the helpline on 020 8450 0515.
Note: A proof of purchase is required in all cases.
For all eligible replacements (where agreed by Timeguard) the customer is responsible for all shipping/postage charges outside of the UK.
All shipping costs are to be paid in advance before a replacement is sent out.

If you experience problems, do not immediately return the unit to the store.
Telephone the Timeguard Customer Helpline:

HELPLINE
020 8450 0515
or email [email protected]
Qualified Customer Support Coordinators will be online to assist in resolving your query.

www.timeguard.com

Controller Instruction Manual

1. General Information

These instructions should be read carefully and retained for further reference and maintenance.

2. Safety

• Before installation or maintenance, ensure the mains supply to the PIR sensor is switched off and the circuit supply fuses are removed or the circuit breaker turned off.
• It is recommended that a qualified electrician is consulted or used for the installation of this PIR sensor and install in accordance with the current IEE wiring and Building Regulations.
• Check that the total load on the circuit including when this PIR sensor is fitted does not exceed the rating of the circuit cable, fuse or circuit breaker.

3. Technical Specifications

• 230V AC 50 Hz
• This PIR is of Class ll Construction and must not be earthed
• Motion Detection Range: Up to 10 meters diameter (4.5m Radius) at a mounting height of 3 meters
• Presence Detection Range: Up to 3 meters diameter (1.5m Radius) at mounting height of 3 meters
• Detection Angle:360°
• Maximum Switching Load: 1500W Halogen/Fluorescent Lighting 420W LED Lighting 420W Discharge Lighting (SON, HQI) 250W Fan Load
• Time ON Adjustment:1 minute to 30 minutes
• Dusk Level Adjustment: Day and Night or Night time only operation
• Minimum depth of Back Box: 16mm
• IP55 Rated suitable for restricted internal applications
• CE Compliant
• EC Directives: Conforms to latest directives
• Multiple PIR Sensor Switching: A maximum of 4 PDSM1500 PIR sensors can be wired in parallel, to enable any detector to turn ON all the lights connected (The total load must not exceed the lamp rating of a single PDSM1500 unit).

4. Selecting a Location

• Careful positioning of the sensor will be required to ensure optimum performance (See diagram “A” & “B” detailing detection range and direction).
• The best all-around coverage is achieved with the unit mounted at the optimum height of 3 meters.
• The sensor is more sensitive to movement ACROSS its field of vision than to movement directly TOWARDS (see diagram “B”). Therefore position the unit so that the sensor looks ACROSS the likely approach path.
• Reflective surfaces (i.e. pools of water or white-painted walls) may cause false activation under extreme conditions.
• During extreme weather conditions the motion sensor may exhibit unusual behavior. This does not indicate a fault with the sensor. Once normal weather conditions return, the sensor will resume normal operation.

5. Installation

• Ensure the mains supply is switched off and the circuit supply fuses are removed or the circuit breaker turned off.
• An isolating switch should be installed to enable the power to be switched ON and OFF for maintenance purposes.
• Terminate the230V 50Hz mains supply and load cables into the terminal block ensuring correct polarity is observed and that all bare conductors are sleeved (See section 6. Connection Diagram).
• The adjustment knobs located beneath the sensor head (see diagram “C”) are factory set to “Walk Test Mode”. Double check they are set as follows; TIME ­ Fully anti-clockwise (Test mode). DUSK ­ Fully clockwise.
• Fit the sensor to the wall box and secure it with the two fixing screws provided.

6. Connection Diagram

• Connect cables to the terminal block as follows;

230V AC 50Hz Mains Supply

Live (Brown or Red) to L
Neutral (Blue or Black) to N

Load

Switch Live (Brown or Red) to L1
Neutral (Blue or Black) to N

7. Setting Up

Walk Test Procedure

• Turn the power to the unit ON. The lamp will immediately illuminate as the unit goes through its “warm-up” period. After approximately 1 minute the lamp will extinguish. This indicates the unit is wired correctly and the unit is in Test Mode.
• Try to remain outside the detection area during the warm-up period.
• The unit will now operate during daytime as well as at night, illuminating the lamp for approx. 5 seconds each time. This allows testing to be carried out to establish whether the sensor is covering the required area.
• Walk across the location the sensor is fitted, to establish the detection area.
• The sensor will detect you approximately up to 9 meters forward at mounting height of 1m.
• As you cross a detection “zone” the lamp will illuminate. Now stand still until the lamp extinguishes (this should take approx. 5 seconds).
• Start moving again after 2 seconds. As you cross each “zone” the lamp will illuminate.
• Repeat the above, walking at various distances and angles to the unit. This will help you to confirm the detection pattern.

Setting Up for Automatic Operation

• When walk tests are complete, the unit can be adjusted for automatic operation.
• The TIME setting controls how long the unit remains illuminated following activation & after all motion ceases.
• Use a thin flat blade screwdriver to make adjustments.
• The Time control knob at fully anti-clockwise is Test Mode, slightly adjust to above the T is minimum time approx. 1 min, whilst the maximum time (fully clockwise) is approx. 30 minutes.
• Set the control to the desired setting between these limits.
• The DUSK control determines the level of darkness required for the unit to start operating. The setting is best achieved by the procedure below;
  1. Set the DUSK control knob fully anti clockwise.
  2. When the ambient light level reaches the level of darkness at which you wish the lamp to become operative (i.e. at dusk) SLOWLY rotate the control in a clockwise direction until a point is reached where the lamp illuminates.
  3. Leave the control set at this point.
• At this position the unit should become operative at approximately the same level of darkness each evening.
• Observe the operation of the unit. If the unit is starting to operate too early (i.e. when it is quite light) adjust the control slightly anti-clockwise. If the unit starts to operate too late (i.e. when it is very dark). Adjust the control slightly clockwise.
• Continue to adjust until the unit operates as desired.

8. Troubleshooting

Problem

• The lamp stays ON all the time at night.
• The PIR keeps activating for no reason at random.
• The PIR will not operate at all.
• The PIR sensor will not operate at night
• The unit activates during the daytime

Solution

• Cover PIR lens with a thick cloth. If the light turns out, check detection area for heat or reflective source. If the light stays ON, check wiring (See section 6. Connection Diagram).
• Turn off at the isolation switch. Turn back ON again after 30 seconds. Leave for approximately 15 minutes. If light activates, check area for false activation from heat, wind or reflective source.
• Check that the power is switched ON at the power supply or isolation switch. Turn OFF the power to the unit and check the wiring connections (See section 6. Wiring Diagram). Check the lamp. If the lamp has failed, replace. Ensure that the lamp is seated correctly in the lamp holder. Please note that the unit will not detect through glass. (e.g. in a glazed porch).
• The level of ambient light in the area may be too bright to allow operation at the current DUSK setting. During the hours of darkness, adjust the DUSK control slowly clockwise until the lamp illuminates (See section 7. Setting Up).
•  Adjust the DUSK Control setting anti-clockwise to lower the level of ambient light required for activation.

3 Year Guarantee

In the unlikely event of this product becoming faulty due to defective material or manufacture within 3 years of the date of purchase, please return it to your supplier in the first year with proof of purchase and it will be replaced free of charge. For years 2 and 3 or any difficulty in the first year, telephone the helpline on 020 8450 0515. Note: A proof of purchase is required in all cases. For all eligible replacements (where agreed by Time guard) the customer is responsible for all shipping/ postage charges outside of the UK. All shipping costs are to be paid in advance before a replacement is sent.

If you experience problems, do not immediately return the unit to the store. Telephone the Time guard Customer Helpline;

HELPLINE
020 8450 0515
or email [email protected]
Qualified Customer Support Co-Ordinator’s will be on-line to assist in resolving your query.

For a product brochure please contact:
Time guard Limited.
Victory Park, 400 Edgeware Road,
London NW2 6ND
Sales Office: 020 8452 1112
or email [email protected]
www.timeguard.com
67-058-426 (Issue 4)

Model: NTT08

1. General Information

These instructions should be read carefully and retained for further reference and maintenance.

2. Safety

• Before installation or maintenance, ensure the mains supply to the time switch is switched off and the circuit supply fuses are removed or the circuit breaker turned off.
• It is recommended that a qualified electrician is consulted or used for the installation of this time switch and install in accordance with the current IEE wiring and Building Regulations.
• Check that the total load on the circuit including when this time switch is fitted does not exceed the rating of the circuit cable, fuse or circuit breaker.

3. Technical Specifications

• 230V AC 50 Hz
• This time switch is of class I construction and must be earthed
• Switch Rating: 16A Resistive (3.68kW); Immersion Heaters
• Switch Type: 16A relay
• Contact Type: Normally Open
• Manual Override: Permanent ON or OFF
• Boost Times: 1 or 2 hour
• Power Status
  LED Indicator: Red
• Output LED
  Indicator: Green
• 7 Day Time Period (7 Day, 5 + 2 Days
  or Individual Day) – 4 ON/OFF switching
• Operating Temperature: 0°C to +40°C
• CE Approved

Note: Not suitable for use with Discharge Lighting.

The LED switching capabilities of this product can be increased to 200W by the addition of the Time guard ZV900 Automatic switch load controller – sold separately.

4. Installation

• Ensure the mains supply is switched off and the circuit supply fuses are removed or the circuit breaker turned off.
• Remove the terminal cover by undoing the fixing screw on the bottom of the time switch.
• Mark the position of the top wall mounting screw. Drill out the top mounting hole taking care to avoid any joists, electrical cables or water/gas pipes that may be hidden beneath the surface. Insert the rawl plug into the hole.
• Fix the top mounting screw and leave 2.5mm proud off of the wall.
• Place the key hole in the top of the product, over the screw head, and slide down.
• Mark the position of the lower mounting hole on the wall using the wall plate as a template.
• Remove the product and drill out the lower mounting hole again taking care to avoid any joists, electrical cables or water/gas pipes that may be hidden beneath the surface. Insert the rawl plug into the hole.
• The 230V 50Hz supply and load cables can enter through the rear knock outs or the front cable entry ports provided. If the rear knock outs are being used, remove the blanking plates and pass the supply and load cables through the holes.
• Place the key hole in the top of the product again, over the screw head, and slide down.
• Secure the unit to the wall using the lower mounting screw.
• If the wiring is through the front cable entry ports, use the cable clamps provided to secure the supply and load cables.
• Terminate the supply and load cables to the terminal block ensuring correct polarity is observed and that all bare conductors are sleeved. Please note the connections are marked beneath the terminal block (see section 5. Connection Diagram).
  • Secure the terminal cover back into place using the fixing screw.

5. Connection Diagram

• The terminals are marked as follows on the bottom of the wall plate;

Note: this device needs to be left to charge for a minimum of 15 minutes once powered up, before it will operate.

6. Battery

• The time switch has a factory fitted rechargeable battery to give clock operation and programme memory back up during loss of mains supply.
• Before programming for the first time, connect the unit to the mains for at least 15 minutes prior to pressing the Rst button and programming the unit.
• If the display is not visible or very faint, charge for 4 hours prior to pressing Rst and programming.
• Approximately 720 hour battery reserve.

7. Reset

The time switch must be reset before programming for the first time, or after subsequent discharge for more than 5 days, and following a 4 hour period of charging.

• Press the Rst button once using a pointed object e.g. a pencil or a paper clip.
• The display will show all characters/digits and then will clear to show the following;
  ASCO = Automatic Summer/ Winter Change Over.
  
• Use the Adv/Ovr button to change between ON and OFF for the automatic summer time adjustment and proceed to section 9.

8. Setting the clock

• Press and hold the Time button for 3 seconds, the word Hold will show on the screen.
• After 3 seconds release the Time button and the screen will show the year;
  
• Use the Adv/Ovr to increase (or the Boost buttons to decrease) the value and set to the correct year.
• Press the Time button once to save the year, and the screen with show the month;
  
• Use the Adv/Ovr or boost button to set the correct month.
• Press the Time button once to save the month, and the screen will show the day;
  
• Press the Time button once to save the day, and the screen will show the time hour first;
  
  Note: The hour is in 24 hour format.
• Use the Adv/Ovr or boost button to adjust to the correct hour.
• Press the Time button once to save the hour, and the minutes can be adjusted.
• Use the Adv/Ovr or boost button to adjust to the correct minutes.
• Press the Time button once to exit the Time/date entry mode.
• The display should now show the correct time/day of the week, for example;
  

Modifying the date and time of day Normally the only change required will be to the time of day minutes, in which case;

• Press and hold the Time button for 3 seconds, the word Hold will show on the screen.
• After 3 seconds release the Time button and the screen will show the year;
  
• Press the Time button repeatedly until the minutes are shown.
  Use Adv/Ovr or Boost to change the minutes to the correct value.
• Press the Time button once to return to operating mode.
  Note: Other changes can be made the same way, but the Time button must be pressed to return to operating mode after any changes. There is no automatic exit from Time/date entry mode.

9. Programming ON/OFF times

The NTT08 has 4 independent On/Off periods available for programming each day. There is a choice of programming options, including 7 days the same (24 hours), 5 + 2 days (where the weekdays are the same, and the two weekend days are the same), and 7 individual days.

• Press and hold the Prg button for 3 seconds, the word Hold will show on the screen.
• After 3 seconds release the Prg button and the MODE screen will be displayed;
  
• Use the Adv/Ovr or Boost to change the day grouping mode. This will step through the following options;
  24hour – Mo Tu We Th Fr Sa Su 5 day – Mo Tu We Th Fr (followed automatically in programming by 2 day – Sa Su)
  Individual day – Mo (followed automatically in programming by each of the other days of the week)
• Once the desired day grouping is selected, press Prg button once to set and move onto programming the ON/OFF times.
• The display will show Prog 1, with dashes for the hours and minutes;
  
  Note: the example shown is for 5 day + 2 day programming
• Use Adv/Ovr or Boost button to set the hour for the first ON period.
• Press the Prg button once to set and move you to the minutes.
• Use Adv/Ovr or Boost button to set the minutes for the first ON period.
• Press the Prg button once to set and move you to the Programme 1 OFF time.
• Use Adv/Ovr or Boost button to set the hour for the first OFF period.
• Press the Prg button once to set and move you to the minutes.
• Use Adv/Ovr or Boost button to set the minutes for the first OFF period.
• Press the Prg button to scroll through Programme 2 ON, Programme 2 OFF, Programme 3 ON, Programme 3 OFF, Programme 4 ON and programme 4 OFF, adding in times as required.
  Note: If further times are not required, just leave the dashes in place and scroll past the rest of the programs using the Prg button.
• After Programme 4 has been entered, then next day grouping will follow e.g. In this example the day grouping will change to 2 day – Sa Su Programme 1 ON.
• Programme the ON/OFF times as before.
• After the last OFF time for programme 4 has been set, press the Prg button once to exit the programme mode.
  Note: At any stage in programming, if the Prg button is pressed and held for 3 seconds, the timer will return to normal operating mode.
• The display will now showthe correct time and day as  per this example;
  
• At this stage the output ON/OFF indicator (as in the above image) may not reflect the current programme status accurately.
• If the time switch should be OFF now, leave as it is.
  Note: The time switch will automatically turn ON at your desired ON time, and will resume the next programme as normal.
• If the time switch should be ON now, press the Adv button once and set it too ON ADVANCE;
  
  Note: The time switch will now automatically turn OFF at your desired OFF time, and will resume the next programme as normal.
• In the same way as for individual programmes, days or groups of days can be omitted either by leaving dashes in all the locations for ON/OFF times for that day or group of days. Alternatively, leaving the programme entry mode before filling in all the ON/OFF times will leave the remaining times blank.
  Note: The only way to re-enter a blank times (or dashes) is to reset the unit

Programming across midnight

• Enter the required programme 1 ON time.
• Set the programme 1 OFF time to 00:00 (i.e. midnight).
• Set the programme 2 ON time to 00:00 as well.
• Enter the required programme 2 OFF time for the next day.

Modifying or adding programmes

• Press and hold the Prg button for 3 seconds, the word Hold will show on the screen.
• After 3 seconds release the Prg button and the MODE screen will be displayed.
  Note: This will automatically display the mode in which it was last programmed.
  For instance, if it was programmed in 5 + 2, then it will show Mo Tu We Th Fr.
• Either – Accept this by pressing the Prg button once, and review the programmed times for this mode by pressing Prg to move through the times.
• Or – Press the Adv/Over or Boost button to change the mode, and then press the Prg button to review the times.
  Note: If you wish to change the mode at this stage, doing so will result in programmes being lost and they will need to be re-entered.
• Review times and adjust as necessary as described at the start of section 9.

10. Advance/Override button

In normal operating mode the Adv/Ovr button advances the programme to the next time change.

• If the output is currently OFF, it will change the output to ON ADVANCE, until the next programmed OFF time.
• If the output is currently ON, it will change the output to OFF ADVANCE, until the next programmed ON time.
• A second push of the Adv/Ovr button selects a permanent ON mode, ON OVERRIDE, where the output is ON irrespective of the programming.
• A third push of the Adv/Ovr button selects a permanent OFF mode, OFF OVERRIDE, where the output is OFF irrespective of the programming.
• A fourth push of the Adv/Ovr button returns the unit to normal operating mode, where the output will conform to the programming.

11. Boost button

• One press of the boost button will provide 1 hour of boost, after which the output will turn OFF.
• Two presses of the boost button will provide 2 hours of boost, after which the output will turn OFF.
• A third press of the boost button will cancel any boost period and return you to normal operating mode.

3 Year Guarantee

In the unlikely event of this product becoming faulty due to defective material or manufacture within 3 years of the date of purchase, please return it to your supplier in the first year with proof of purchase and it will be replaced free of charge. For the second and third years or any difficulty in the first year telephone the helpline on 020 8450 0515.

Note: A proof of purchase is required in all cases.  For all eligible replacements (where agreed by Timeguard) the customer is responsible for all shipping/postage charges outside of the UK. All shipping costs are to be paid in advance before a replacement is sent out.

If you experience problems, do not
immediately return the unit to the store.
Telephone the Timeguard Customer Helpline;
HELPLINE
020 8450 0515

or email
[email protected]

Qualified Customer Support Co-ordinators
will be on-line to assist in resolving your query.

For a product brochure please contact:

Timeguard Limited.
Victory Park, 400 Edgware Road,
London NW2 6ND
Sales Office: 020 8452 1112
or email [email protected]

www.timeguard.com

67-058-483 (Issue 5)

TIMEGUARD Automatic Light Switch with Photocell – 2 Wire Installation Guide

Model: ZV210N

1. General Information

These instructions should be read carefully in full prior to installation, and retained for further reference and maintenance.

2. Safety

• Before installation or maintenance, ensure the mains supply to the light switch is switched off and the circuit supply fuses are removed or the circuit breaker turned off.
• It is recommended that a qualified electrician is consulted or used for the installation of this light switch and install in accordance with the current IEE wiring and Building Regulations.
• Check that the total load on the circuit including when this light switch is fitted does not exceed the rating of the circuit cable, fuse or circuit breaker.

3. Technical Specifications

• Mains Supply: 230V AC 50 Hz
• Battery: 9V DC battery supplied (replaceable).
• 2 wire connection: No neutral required
• This light switch is of class II construction and must not be earthed
• Switch Type: Single or Two way
• Switch Rating: 2000W Incandescent/Halogen,
  250W Fluorescent
  (Low-loss or Electronic Ballast),
  250W CFL (Electronic Ballast),
  400W LED Lighting
  (PF 0.9 or higher).
• Minimum Depth of Wall Box: 25mm
• Operating Temperature: 0°C to +40°C
• Mounting Height: 1.1m for optimum detection range
• On-time Adjustment: 0, 2, 4, 6, 8 hours or D (Dusk until Dawn).
• LUX Adjustment: 1 ~10lux (Moon symbol) to 300lux (Sun symbol)
• Front Cover: Conceals On-time/LUX adjustments and battery compartment, with retaining screw
• Manual ON/OFF Switch
• Low Battery Indication: The LED will pulse 1 sec ON, 8 secs OFF
• IP Rating: IP40
• CE Compliant
• Dimensions – H=86mm, W= 86mm, D=29.5mm

4.Installation

Note: The installation of this light switch should be protected
by suitable circuit protection of up to 10A rating.

4.1 Ensure the mains supply is switched off and the circuit supply fused are removed or the circuit breaker is turned off, until you have completed the installation.
4.2 Loosen the retaining screw located on the bottom of the light switch, and open the hinged front cover that conceals the battery holder and On-time/Lux adjusters. (Fig. 3)

4.3 Fit the 9V battery (supplied) maintaining the correct polarity.
(Fig. 4)

4.4 Remove the existing light switch, and transfer the wires to the ZV210N (See section 5.Connection Diagram).

4.5 Secure the unit to the back box with the fixing screws provided, forming the cables during installation to avoid any entrapment and cable damage.

5. Connection Diagram

6. Testing

• Ensure that the light switch is in the OFF position.
• Turn the Lux Adjustment, which is located beneath the front cover on the right hand side of the light switch, fully anti clockwise to the Moon symbol.
• Turn the On-time Adjustment, which is located beneath the front cover on the right hand side of the light switch, clockwise to the 2 hour mark
• Emulate darkness by covering the Light Sensor (make sure the Light Sensor is fully covered, use black insulation/PVC tape if needs be).
• The lamp will automatically turn ON.
• After 3 seconds, uncover the Light Sensor.
• The lamp will turn off after it’s set period 2, 4, 6 or 8 hours or until dawn.
• To revert to a normal light switch, turn the On-time Adjustment fully anti-5 clockwise to the 0 hour mark.

7. Setting Up For Automatic Operation

• Ensure the light switch is in the OFF position.
• Turn the Lux Adjustment fully anti-clockwise to the Moon symbol.
• Turn the On-time Adjustment to the desired setting (2, 4, 6, 8 Hours or D for Dawn).
• When the ambient light level reaches the level of darkness at which you wish the lamp to become operative (i.e. at dusk) SLOWLY rotate the lux adjustment control in a clockwise direction until a point is reached where the lamp illuminates.
• Leave the Lux Adjustment set at this point.
• At this position, the unit should become operative at approximately the same level of darkness each evening.

Note: If you wish to use unit as a normal light switch, turn the On-time Adjustment fully anti-clockwise to the 0 hour mark. If you wish to use the Automatic feature again, please follow the above instructions.

Adjustments

• If you find that your lights switch on when it is too dark, turn the Lux Adjustment clockwise towards the Sun symbol.
• If the light is in operation when it is too light turn the Lux Adjustment towards the Moon symbol.

Notes:

• The ZV210N light switch has a built-in delay function to ensure that momentary changes in the light do not switch it ON.
• The hours shown on the dial are only approximate guides, do not expect great accuracy.
• Once the switch has turned ON and the programme has turned OFF after the required number of hours, it is important not to allow artificial light to fall on it, followed by a period of darkness. This will fool the switch into thinking it is dark again and it will operate. Care should therefore be taken to prevent light falling onto the switch, e.g. table lamps.

8. Low Battery Warning

• When the 9V battery is running low, the RED LED will pulse 1 second ON, 8 seconds OFF, as warning and indication to change it (See section 4. Installation, step 4.2 & 4.3 for how to access the battery compartment).

9. Support

Note: If you have any concerns that the intended application of this product does not meet your requirements, please contact Timeguard directly prior to installation.

3 Year Guarante

In the unlikely event of this product becoming faulty due to defective material or manufacture within 3 years of the date of purchase, please return it to your supplier in the first year with proof of purchase and it will be replaced free of charge. For the second and third years or any difficulty in the first year telephone the helpline on 020 8450 0515.

Note: A proof of purchase is required in all cases. For all eligible replacements (where agreed by Timeguard) the customer is responsible for all shipping/postage charges outside of the UK.
All shipping costs are to be paid in advance before a replacement is sent out.

If you experience problems, do not immediately return the unit to the store.
Telephone the Timeguard Customer Helpline:

HELPLINE
020 8450 0515

or email [email protected]
Qualified Customer Support Coordinators will be online
to assist in resolving your query.

For a product brochure please contact:

Timeguard Limited.
Victory Park, 400 Edgware Road,
London NW2 6ND
Sales Office: 020 8452 1112
or email [email protected]

www.timeguard.com