TOMMY EARBUDS 333
AIR SPORT
NOISE-CANCELING WIRELESS EARBUDS
Bluetooth
USER MANUAL

HILFIGER EP333 Noise Cancelling Wireless Earbuds

Multifunction button:
Power on/off
Charge Directions and Use:

• Fully charge the earphones before using them for the first time.
• Plug the USB charging cable Into the controller of the headphones.
• The LED light will turn blue when the earphones are fully charged.

Attention: Please use the original Included charging cable to connect the earphones to your computer or compatible USB charging device.
Basic Use:

	Power on: Press & hold the multi-function button until the blue LED goes on.  Power off: Press & hold the power button until the red LED goes on
	Pairing: When the unit is powered off, press & hold the multi-function button for about 10-15 sec until blue & red LED lights begin to blink. The unit is now in pairing mode. Make sure your Bluetooth-enabled device is discoverable. In Available Devices choose “TOMMYEARBUDS 333” and select ‘Pair.
	Volume control: While listening, press the V+ button to increase volume, or the V- button to decrease volume.
	Music track: While listening, press & hold the V+ button for the next song, and press & hold the V- button for the previous song.
	Pause/Play: While listening, press the multi-function button to pause music. Press the button again to play music.
	Answer/End call: Tap the multi-function button. Reject call: Press the multi-function button for 2-3 seconds.

LED Indicator:
Low battery warning:
Red LED flashing.
Charging:
Red LED on when charging and blue LED on when fully charged. }
Bluetooth connected:
Blue LED flashing slowly.
Power on/off:
When turning the earphones on the LED light will blink blue. When turned off the LED will turn red.
Bluetooth pairing:
Blue and red LED flashing rapidly together.
Pairing The Bluetooth Earphones:
Pairing the device Is quite simple. Put the earbuds and compatible Bluetooth device close to each other (no more than 3 feet apart). When powering on the SWS EtECNONICS earbuds press and HOLD down the center power button on the controller. The voice prompt will say “Ready to pair”
***DO NOT release the power button for another 10-15 sea and the LED indicator lights should begin to blink red and blue. Your device is now in pairing mode.
From here you’ll have to navigate through Bluetooth Settings on your mobile device and choose “SVESEP333” from the list of all available Bluetooth devices within range. This should begin the pairing sequence.
After pakhg Is successfully completed, you ‘Mil hear a tone in the earphones indicating that the connection has been established and the voice prompt will state “Your Device Is Now Paired.’
Now you can use your Tommy Earbuds 333 to listen to music and make phone calls.

SPECIFICATION

Warnings and Notes:

• Do not store the unit in a high-temperature environment, including intense sunlight or heat. Do not place the unit near fire or other excessively hot environments.
• Be cautious of excessive drops, bumps, abrasions, or other types of impact. If there is any damage to the battery such as dents, punctures, tears, or deformities of corrosion, due to any cause, discontinue use and contact the manufacturer or dispose of it in an appropriate manner.
• Do not disassemble or attempt to modify or replace any part of this unit.
• Do not expose the unit to moisture, or snow, or submerge it in liquid.
• Do not use units in the vicinity of flammable fumes or gases (such as propane tanks or large engines).
• Do not attempt to operate the unit using any other method than directed.

TECHNICAL SUPPORT:

Please do not attempt to fix the product by yourself. If you are experiencing any problems with the product please do not return it to the store you bought it from. You can contact our technical support representatives and they will assist you with any questions you might have.
Questions? Visit our support page online at www.sveselectronics.com

WARRANTY REGISTRATION

To register your SVES Electronics product please visit www.sveselectronics.com
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– – Reorient or relocate the receiving antenna.
– – Increase the separation between the equipment and receiver.
– – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– – Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirements.

TOMMY HILFIGER ME42 Wireless Headphone

1. 
   Power On: Push forward the button
   Power Off: Push down the button
2. . I ◄ In Wireless mode, Short Press: Previous song; Long Press: volume –
3. . ► I In Wireless mode, Short Press: next song; Long Press: volume +
4. . ►II When the oonnection is successful, when there is an incoming call, short press the button to answer, long press to reject, double-click to dial back the last
   number Play status, short press play, pause Indicator light:
   Wireless Mode: red and blue light flash in pairing mode, and blue light flash slowly after successful pairing.
   Charging Mode: the red light will be on long when charging, and the red light will be off after charging
   Wireless Operation lnsbuctions: Push forward the cu key to power on.
   Red and blue light flash, product enters into the pairing mode. Search this wireless product with the mobile phone, product BT name is Tommy
   Headphones ME42. When the phone searches for the Tommy Headphones ME42 name and connects, if prompted for a password, the password is 0000.
   When the wireless connection is successful, the blue light flashes slowly. Open the mobile phone music player to play music, the product can control the wireless music up and down.
   Play, pause, call, answer, redial and other functions. Line External Audio Input Operation Instructions:
   When the product is powering on, insert the audio cable into AUXLINEIN mode. Support mobile phone/MP4/MP3/CO/laptop and other external audio input.

Specifications:

USB charging: DC 5V IN
Winoless frequency: 2 402-2.480GHz
Wireless Distance: 10 m
Frequency response: 20HZ-20khz
Output power. 35mW
Signal to noise ratio: 88D6
Charging Time: 2 hours

Remarks: If the headset can not be turned on, please charge the headset before use.

WARRANTY

Sound Archttects offers a two year warranty for our electronics products. If a product is faulty, not fit for purpose, or does not function as advertised, the consumer has a right to repair, replacement, price reduction or reimbursement
Note: We understand on a national level, countries can have rules providing for longer periods, hierarchy of the remedies available to the consumer, or notice periods and will work with each country to commit to the warranty requirements.

Our Warranty does not cover the following:

1. Purchased from unauthorized sellers
2. Physical and Water damage caused by improper use
3. Free or promotional products.

Initiating a Warranty Claim
Please contact us at [email protected] or through our Contact Us
page soundarchitect~com with the following information:

1. Your Name
2. Product Name
3. Date of Purchase
4. Where is was purchased from

We aim to respond to all emails within 24 hours.

FCC Statement

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Information
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.