4352 Comcast XR15 Remote 2015

Voice Remote

1. Meet Your Remote

2. Turn On Your Remote
Your remote arrives with the AA batteries already installed, but not activated. Here is how to power it on for the first time.

3. Pair Your Remote for Voice Control

Use Voice Control to search for networks and shows, set DVR recordings, and get recommendations.

4. Troubleshooting

Remote not working with your TV?
The remote has to be programmed to the TV and/or audio receiver to control power, volume, and input. Go to the Remote Settings screen on X1 to program control of your TV and audio receiver.

Need help?
Say “Remote help” to see tips & tricks for using your remote.

Voice command not working?
Make sure you’re pressing the Voice button while you speak into the remote, and release it when complete.

Need to pair with another box?
If you want to use your remote with a different set-top box repeat step 3 while pointing the remote at the box.

Looking for more information?
Visit Xfinity.com/remotes for additional help with Xfinity remotes

5. FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not used in accordance with the instructions, may cause harmful interference to radio communications.

There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase or decrease the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that which the receiver is connected.
• Consult the dealer or an experienced remote control / TV technician for help.
• It is strongly recommended that the TV be plugged into a separate wall outlet.

The user is cautioned that changes and modifications made to this equipment without the approval of the manufacturer could void the user’s authority to operate this equipment.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC ID: MG3-4352

Universal Remote Control URC1056 User Guide

Step 1 Installing Batteries

1. Remove battery cover.
   
2. Insert 2 AA batteries. Match the + and – marks.
   
3. Replace battery cover.
   

Step 2 Setup Television Control

1. Press the TV mode key.
   
2. Press and hold SETUP until TV mode key blinks twice.
   
3. Enter 1st TV code for your TV brand from the code list.
   
4. Press Ch+ repeatedly until your device turns ON or OFF.
   
5. To save the working code, press and hold SETUP until the LED blinks twice.
   

Step3 Setup Control of Other Equipment

1. Press the mode key for the device you wish to setup.
   
2. Press and hold SETUP until the mode key blinks twice.
   
3. Enter 1st code for your brand from the matching code list.
   
4. Press power key to test with your equipment. If the device turns off, setup is complete.
   
5. If device does not turn off, then repeat STEP3 using the next code for your brand.
   

Step4 Locking Volume Controls to Audio Device

Note: Volume Control defaults to TV. Perform this step only if you wish to use an AUDIO receiver, Amp, or home theater surround system for Volume Control when watching cable.

1. Press and hold SETUP until the mode key blinks twice.
   
2. Enter 9-9-3
   
3. Press the AUD mode key to lock volume to AUDIO.
   

TROUBLESHOOTING

Problem: Mode key does not blink when a key is pressed.
Solution: Replace batteries.
Problem: Mode key blinks, but remote does not control my equipment.
Solution: Press correct mode key and point remote at equipment you need to control.
Problem: Tried all codes for my brand of device and none work.
Solution: Try CODE SEARCH (STEP 2a)  method or go to www.urcsuppport.com for model-based search.
Problem: I want to swirch BOLUME LOCK from AUD to TV control.
Solution: Follow STEP-4, but press the TV mode key instead of AUD mode key.
Problem: My TV power turns off when my cable power turns on.
Solution: Manually press the power button on the front of the cable box or your TV to get back in sync.

Web for Help: WWW.URCSUPPORT.COM