Waterpik® Water Flosser Models WF-11 | WF-12
Hydropropulseur Waterpik® Models WF-11 | WF-12
Irrigador dental Waterpik® Modelos WF-11 | WF-12

www.waterpik.com

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS BEFORE USING.

• This product is for household use.
  When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following:
  DANGER:
  To reduce the risk of electrocution:
• Do not handle USB power supply with wet hands.
• Do not place in or drop into water or other liquid.
• Do not use while bathing.
• Do not place or store product where it can fall into a tub or sink.
• Check the power supply/charger cord for damage before the first use and during the life of the product.

WARNING:
To reduce the risk of burns, electrocution, fire, or injury to persons:

• Do not charge this unit with any charging devices other than the one provided.
• Do not plug the power supply into a voltage system that is different from the voltage system specified on the device or power supply. Use with improper voltage will damage product and VOID warranty.
• If product is opened/disassembled for ANY reason, warranty is VOID.
• Do not use this product if it has a damaged cord or power supply, if it is not working properly, if it has been dropped or damaged, or dropped into water. Contact Water Pik, Inc. or visit www.waterpik.com.
• Do not direct water under the tongue, into the ear, nose or other delicate areas. This product is capable of producing pressures that may cause serious damage in these areas.
• Do not direct water into the nose or ear. The potentially deadly amoeba, Naegleria fowleri, may be present in some tap water or unchlorinated well water and may be fatal if directed into these areas.
• Use this product only as indicated in these instructions or as recommended by your dental professional.
• Only use tips and accessories recommended by Water Pik, Inc.
• Magnetic field: Pacemakers and similar implanted medical devices may be affected by magnet.
• Do not drop or insert any foreign object into any opening or hose.
• Keep power supply/charger cord away from heated surfaces.
• Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
• Do not use iodine or water insoluble concentrated essential oils in this product. Use of these can reduce performance and will shorten the life of the product. Use of these products may void warranty.
• Fill reservoir with water or other dental professional recommended solution only.
• Remove any oral jewelry prior to use of this product.
• Do not use if you have an open wound on your tongue or in your mouth.
• If your physician or cardiologist has advised you to receive antibiotic premedication before dental procedures, you should consult your dentist before using this instrument or any other oral hygiene aid.
• Close supervision is necessary when this product is used by, on or near children or people with special needs.
• If the Pik PocketTM tip (not included in all models) separates from the shaft for any reason, discard tip and shaft and replace with new Pik PocketTM tip (PP-100E).
• Do not use this product for more than 5 minutes in each two-hour period.
• Unit will shut off automatically after 3 minutes of continuous usage.
• Children should be supervised to ensure that they do not play with the appliance.

SAVE THESE INSTRUCTIONS

PRODUCT DESCRIPTION

1. Power ON/OFF
2. Handle
3. Water ON/OFF switch
4. Pressure control
5. Magnetic handle cradle
6. Handle hose swivel
7. Tip
8. Tip rotator
9. Reservoir lid
10. Reservoir
11. Tip eject button
12. Charging contacts
13. Base

TIPS
A. Orthodontic Tip*
– Braces/General Use
B. Pik PocketTM Tip*
– Periodontal Pockets/Furcations
C. Plaque SeekerTM Tip*
– Implants/Crowns/Bridges/ Retainers/General Use
D. Classic Jet Tip**
– General Use
E. Implant Denture Tip**
– Fixed Implant Bridges and Dentures
F. Tongue Cleaner**
– Fresher Breath

NOT ALL TIPS INCLUDED IN ALL MODELS

*Replace Every 3 months **Replace Every 6 months
Replacement tips/attachments may be purchased online at www.waterpik.com, or by phone from Water Pik, Inc. at 1-800-525-2774 (USA). To find detailed information about tips, other accessories, and product usage please visit our website at www.waterpik.com

GETTING STARTED

Charging Unit Prior to First Use
Plug the power supply into the wall outlet and connect the magnetic plug to the unit (see image) for approximately 4.5-5 hours. The charge indicator on the unit will glow while charging and then begin to flash momentarily every 3 seconds when the unit is fully charged. A full charge will last for approximately 4 weeks when unit is used once a day for one minute a day. When the batteries are in need of charging (approximately 30% charge left) the charge indicator light will blink 3 times quickly to indicate that the user should consider recharging the unit. A complete recharge will take 4.5-5 hours. If you use your Water Flosser once a day or less, it is recommended that you charge it every 3-4 weeks. If you use it twice a day or more, charge the unit more frequently.

Preparing the Reservoir
Remove the reservoir, lift the reservoir lid, and fill with warm water. Fill with warm water. Replace the reservoir over the base and press down firmly and close the lid.

Inserting and Removing Tips
Insert tip into the center of the Water Flosser handle, pressing down firmly until the tip clicks into place. The colored ring will be flush with the top of the handle if the tip is correctly locked into place. To remove tip from the handle slide the tip eject button on the handle.

Prime Unit (First Time Use Only)
Set pressure control on base to high (pressure setting No.10), point the handle and tip into sink. Turn power and water ON until water flows from the tip.

Adjusting the Pressure Setting
Set the pressure control on the base of the unit to the lowest setting (pressure setting No.1) for first-time use. Gradually increase pressure over time to the setting you prefer ­ or as instructed by your dental professional.

Using the Water Flosser
Always place the tip in your mouth before turning the unit power ON. With water switch on handle in OFF position, turn power on. Lean over sink and slightly close lips enough to prevent splashing while still allowing water to flow from mouth into the sink. Turn water switch ON. When finished, turn water switch and power OFF. During use you can stop the flow of water by sliding the water switch on handle to the OFF position.
NOTE: Motor will continue to run.
For best results, start with back teeth and work toward the front teeth. Direct the stream at a 90-degree angle to your gumline with tip in mouth. Glide tip along gumline and pause briefly between teeth. Continue until you have cleaned the inside and outside of both the upper and lower teeth.

One-Minute Timer/30-second Pacer
The Water Flosser will create a short pause at 30-seconds, to remind you to move to the other arch of your mouth and another short pause at 1-minute to signal you have reached the recommended cleaning time. The unit will continue to run without pauses until the unit is turned off. Depending on the pressure setting, some water will remain in the reservoir after 1-minute.

When Finished
Turn the power OFF. Empty any liquid left in the reservoir.
NOTE: If you used mouthwash or other solution besides water, see “Using Mouthwash and Other Solutions” section.

NOTE: NOT ALL TIPS INCLUDED WITH ALL MODELS.
TIP USAGE
Pik PocketTM Tip
The Pik PocketTM tip is specifically designed to deliver water or anti-bacterial solutions deep into periodontal pockets. To use the Pik PocketTM tip, set the unit to the lowest pressure setting. Place the soft tip against a tooth at a 45-degree angle and gently place the tip under the gumline, into the pocket.

Tongue Cleaner Tip
Set to lowest pressure setting, place tip in the center/middle of your tongue about half way back. Pull forward with light pressure. Increase pressure as you prefer.

Orthodontic Tip
To use the orthodontic tip, gently glide tip along gumline, pausing briefly to lightly brush area between teeth and all around orthodontic bracket, before proceeding to the next tooth.

CLEANING AND TROUBLESHOOTING YOUR WATERPIK® WATER FLOSSER

Implant Denture Tip
The Implant Denture tip is specifically designed to access areas that are unreachable with a Classic Jet tip, Plaque SeekerTM tip, Orthodontic tip, or Pik PocketTM tip. To use the Implant Denture tip, place the tip on the lingual side at one end of the implant retained denture. The opening of the tip is directed between the natural gum tissue and the denture directing the water under the denture. Slowly glide the tip along the space between the natural gum tissue and the denture until you have cleaned underneath the entire length of the denture.

Plaque SeekerTM Tip
To use the Plaque SeekerTM tip, place the tip close to the teeth so that the bristles are gently touching the teeth. Gently glide tip along gumline, pausing briefly between teeth to gently brush and allow the water to flow between the teeth.

Using Mouthwash and Other Solutions
Your Waterpik® Water Flosser can be used to deliver mouthwash and antibacterial solutions. After using any special solution, rinse unit to prevent clogging by partially filling reservoir with warm water and running unit with tip pointed into sink until unit is empty.

Cleaning
Before cleaning, disconnect power supply/charger cord. Clean the product when necessary by using a soft cloth and mild non-abrasive cleanser. The water reservoir is removable for easy cleaning and is top rack dishwasher safe.

Removing Hard Water Deposits / General Cleaning
Hard water deposits may build up in your unit, depending on the mineral content of your water. If left unattended, it can hinder performance. Cleaning internal parts: add 2 tablespoons of white vinegar to a full reservoir of warm water. Point the handle and tip into sink. Turn unit ON and run until reservoir is empty. Rinse by repeating with a full reservoir of clean warm water. This process should be done every 1 to 3 months to ensure optimal performance.

Leakage
If leaking due to a damaged hose, replacement hoses and handles can be purchased at www.waterpik.com or contact Water Pik Inc. customer service for a self service repair kit.

BATTERY REMOVAL

Battery Removal

The rechargeable battery inside the product cannot be replaced and shall be removed at the end of the product’s life prior to recycling. This process is not reversible and voids the product warranty. Observe basic safety precautions when you follow the procedure below. Be sure to protect your eyes, hands, fingers and the surface on which you work. Deplete the battery charge until the unit no longer operates prior to battery removal.

1. Turn unit over. Remove product label (Model WF-12 Only)
   
2. Remove the 4 rubber feet by carefully prying them upward with a small flat head screwdriver.
   
3. Remove 5 screws from the indicated areas with a small Phillips head screwdriver.
   
4. Turn unit upright and remove reservoir and reservoir lid.
   
5. Remove upper housing by pulling it upward as shown.
   
6. Remove screws from the indicated areas with a small Phillips head screwdriver.
   
7. Pull circuit board assembly aside. Remove 4 screws from the indicated areas with a small Phillips head screwdriver.
   
8. Lift up battery cover as shown.
   
9. Remove battery from housing.
10. Cut the black battery wire with a pair of scissors or side-cutters then cut the red battery wire.
    NOTE: DO NOT CUT BOTH BATTERY WIRES AT THE SAME TIME.
11. Please recycle the unit and safely dispose of the battery per local or state requirements.

LIMITED THREE-YEAR WARRANTY

Service Maintenance
Waterpik® Water Flossers have no consumer serviceable electrical items and do not require routine service maintenance. For all parts and accessories go to www.waterpik.com. You may also call our toll-free customer service number at 1-800-525-2774 (USA) or 1-888-226-3042 (Canada). Refer to the serial and model numbers in all correspondence. These numbers are located on the bottom of your unit.
Still have questions? Go to www.waterpik.com.

Water Pik, Inc. warrants to the original consumer of this new product that it is free from defects in materials and workmanship for 3 years from the date of purchase. Consumer will be required to submit the original purchase receipt as proof of purchase date and if requested, the entire product, to support a warranty claim. Water Pik, Inc. will replace the product, provided the product has not been abused, misused, altered or damaged after purchase, was used according to instructions, and was used only with accessories or consumable parts approved by Water Pik, Inc. Installation is the responsibility of the consumer and is not covered by the warranty. This limited warranty excludes accessories or consumable parts such as tips, etc. Use with improper voltage will damage product and VOID warranty. This warranty gives you specific legal rights. You may also have other rights that vary, depending on the law in your place of residence.

WATER PIK, INC. DISCLAIMS ALL OTHER EXPRESS OR IMPLIED WARRANTIES TO THE EXTENT PERMITTED BY LAW INCLUDING, BUT NOT LIMITED TO, ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ALL IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. SOME STATES OR PROVINCES MAY NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE MAY NOT APPLY TO YOU.

For USA Only
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Limitation of Liability
This limited warranty is your sole remedy against Water Pik, Inc. and it shall not be liable for any damages, whether direct, indirect, incidental, special, consequential, exemplary or otherwise, including but not limited to property damage, arising out of any theory of recovery, including statutory, contract or tort.

Arbitration
BINDING ARBITRATION AND WAIVER OF RIGHT TO ASSERT MATTERS IN COURT AND RIGHT TO JURY TRIAL By purchasing, installing, or using this product you agree that any controversy or claim arising out of or relating to your purchase, use, modification, installation, or removal of this product shall be settled by binding arbitration. The arbitrator’s decision will be final and binding. Judgment on the award rendered by the arbitrator may be entered in any court having jurisdiction over the matter. Further, you agree that you will not have the right to litigate any claim arising out of or in relation to your purchase, use, modification, installation, or removal of this product in any court or to have a jury trial on that claim.

Arbitration of any matters shall be administered by the American Arbitration Association and conducted by one arbitrator in accordance with the consumer arbitration rules of the American Arbitration Association in effect at the time of filing of the demand. The venue for all such arbitrations shall be Colorado and any such arbitration shall be subject to the Federal Arbitration Act and Colorado law.

WAIVER OF RIGHT TO PARTICIPATE IN CLASS ACTIONS OR PURSUE CLAIMS IN A REPRESENTATIVE CAPACITY. Further, by purchasing, installing, or using this product you agree that arbitration must be on an individual basis. This means neither you, nor we, may join or consolidate claims in arbitration by or against other purchasers or users of Water Pik, Inc. products or the general public. Additionally, you may not litigate in court or arbitrate any claims as a representative or member of a class or in a purported representative capacity on behalf of the general public, other purchasers or users of this product, other persons or entities similarly situated, or in a private attorney general capacity.
Water Pik, Inc., a subsidiary of Church & Dwight Co., Inc.
1730 East Prospect Road
Fort Collins, CO 80553-0001 USA
1-800-525-2774
www.waterpik.com
Designed and Tested in the USA. Made in China.

Introduction

Thank you for purchasing this Waterpik® shower head. This booklet provides information to make installation easy and quick. You are close to enjoying a powerful and invigorating shower experience with your new Waterpik® shower head.
You can view more information about Waterpik® shower head products at www.waterpik.com. To learn more about Waterpik® water for wellness® benefits go to www.waterpikwellness.com.
Note: Pictures shown may not directly match your shower head.

PRIOR TO INSTALLATION

• Remove old shower head and remove all pipe tape.
• Ensure that the washer from the old shower is not connected to the shower pipe. Use a thin utensil to check inside the shower pipe for washers, such as a pencil or screw driver. Do not use your fingers.
• Gather the tools necessary to install your new shower head

TOOLS YOU MAY NEED

• Tools may be needed for removal of old shower head or tightening new shower head.
• Adjustable Wrench or Pliers (not included).
  
  
• Soft Cloth (not included).
  
• Pipe tape is not recommended.
  

Hand Held Shower Head

1. Tighten pivot ball to pipe by turning in a clockwise direction as shown. Ensure large nut is secure by hand tightening.
   
2. Connect either end of the hose to the bottom of the bracket by turning clockwise. Hand tighten. (See note below).
   
3. Connect other end of hose to hand held shower head and hand tighten.
   
4. Place hand held shower head in bracket.
   

Vacuum Breaker Backflow Prevention
Note: Several U.S. state and local municipal plumbing codes require the use of a backflow prevention device when installing a hand shower. This device is termed a vacuum breaker. If your hand shower includes a vacuum breaker it will be located in the hose, and the hose end with the vacuum breaker will include a sticker that reads “attach this vacuum breaker end to shower bracket.” If the hose is not installed in this manner, water will not flow. If your hand shower does not include a vacuum breaker, and you would like to obtain one free of charge, please contact us at 1-800-525-2774 (U.S. calls only) and request part number 20009558.

OPERATION

Spray Selector:
Spray Selector allows you to select from various spray patterns. Spray pattern is controlled by the small lever that rotates left and right. Rotate the face of the shower head to change settings.

SPECIAL FEATURES

Align the spray selector with the handle to activate the PowerComb® spray. PowerComb is a natural water comb that penetrates deep to the roots of the hair for a thorough rinse and scalp massage.
Move the tab to the left for SoftComb™ spray, a softer blanket of sweeping water for gentler rinsing.

WARNINGS:

• To avoid hot water dangers and conserve even more energy, make sure your water heater is set at 120°F (48.9°C) or below.
• Test the tub/shower water with your hand before bathing.
• For additional safety for Ecoflow® or high efficiency shower heads, it is recommended that all homes have installed a pressure balance tub and shower valve with the rotational limit stops properly set by a plumber. If you are unsure of your valve type consult your plumber.
• For external use only. The potentially deadly amoeba, Naegleria fowler, may be present in some tap water or unchlorinated well water.
• Always ensure the hand held shower head is properly placed in the bracket, so as to prevent the shower head from falling.
• Do not pull on or tug the flexible hose. This may result in the shower head coming loose and falling.

CARE AND CLEANING

• To maintain proper working conditions cleaning is required when mineral deposits appear on the spray orifices. To clean mineral deposits, gently rub the rubber nozzles on the face of the shower head to dislodge.
• To clean heavier deposits, remove shower head and soak face down in 1-2 cups of white vinegar (use white vinegar only) for about 2-3 hours. Replace shower head and run in each mode to flush out vinegar. Repeat as necessary.
• Do not clean or rinse any part with harsh chemicals, heavy duty cleaners, or abrasives; this may damage parts or finish and will void warranty.
• Clean filter screen by unscrewing from the pivot ball and rinse by back flushing to remove particles. Follow steps 1-3 under installation to reinstall shower head, making sure washer is re-seated on top of filter screen.

TROUBLESHOOTING GUIDE

LIFETIME LIMITED WARRANTY

Save your receipt as proof of purchase is required for warranty action. Water Pik, Inc. warrants to the original purchaser of this product that it is free from defects in material and workmanship for as long as the original purchaser owns this product. Water Pik, Inc. will replace the product which in our opinion is defective, provided that the product has not been abused, misused, altered or damaged after purchase. (This includes damage due to use of tools or harsh chemicals.) In the event an item has been discontinued we will replace with what we deem to be the closest product. Water Pik, Inc. is not responsible for labor charges, installation, or other consequential cost. The responsibility of Water Pik, Inc. shall not exceed the original purchase price of the product. This warranty gives you specific legal rights. You may also have other rights that vary where you reside.
Water Pik disclaims all other express or implied warranties to the extent permitted by law including, but not limited to, all warranties of merchantability and fitness for a particular purpose. All implied warranties are limited to the duration of this limited warranty. Some states or provinces may not allow limitation on how long an implied warranty lasts, so above may not apply to you.

For USA Only
Limitation of Liability: This limited warranty is your sole remedy against Water Pik and it shall not be liable for any damages, whether direct, indirect, incidental, special, consequential, exemplary or otherwise, including but not limited to property damage, arising out of any theory of recovery, including statutory, contract or tort.

BINDING ARBITRATION AND WAIVER OF RIGHT TO ASSERT
MATTERS IN COURT AND RIGHT TO JURY TRIAL
By purchasing, installing, or using this product you agree that any controversy or claim arising out of or relating to your purchase, use, modification, installation, or removal of this product shall be settled by binding arbitration. The arbitrator’s decision will be final and binding. Judgment on the award rendered by the arbitrator may be entered in any court having jurisdiction over the matter. Further, you agree that you will not have the right to litigate any claim arising out of or in relation to our purchase, use, modification, installation, or removal of this product in any court or to have a jury trial on that claim.
Arbitration of any matters shall be administered by the American arbitration association and conducted by one arbitrator in accordance with the consumer arbitration rules of the American Arbitration Association in effect at the time of filing of the demand. The venue for all such arbitrations shall be Colorado and any such arbitration shall be subject to the Federal Arbitration Act and Colorado law.

WAIVER OF RIGHT TO PARTICIPATE IN CLASS ACTIONS OR
PURSUE CLAIMS IN A REPRESENTATIVE CAPACITY.
Further, by purchasing, installing, or using this product you agree that arbitration must be on an individual basis. This means neither you, nor we, may join or consolidate claims in arbitration by or against other purchasers or users of Water Pik products or the general public. Additionally, you may not litigate in court or arbitrate any claims as a representative or member of a class or in a purported representative capacity on behalf of the general public, other purchasers or users of this product, other persons or entities similarly situated, or in a private attorney general capacity.

If product malfunctions or becomes damaged, stop use and contact Water Pik, Inc. for assistance.

Have any questions or need assistance?

For quick service prior to calling have your model number and receipt ready.

In the U.S., call our toll-free In Canada, call our bilingual Customer Assistance Line toll-free Customer Assistance 1-800-525-2774, Monday – Line 1-888-226-3042, Monday – Friday, 7:00 AM – 5:00 PM MST. Friday, 7:00 AM – 5:00 PM MST.
English only. or visit www.waterpik.ca or visit www.waterpik.com © 2021 Water Pik, Inc.

Contact Us

Address: Water Pik, Inc., a subsidiary of Church & Dwight Co., Inc. 1730 East Prospect Road Fort Collins, CO
Phone: 80553-0001
Web: U.S.A. www.waterpik.com

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS BEFORE USING.

• This product is for household use.

When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following:

DANGER

To reduce the risk of electrocution:

• Do not handle plug with wet hands.
• Do not place in or drop into water or other liquid.
• Do not use while bathing.
• Do not place or store product where it can fall or be pulled into a tub or sink.
• Do not reach for a product that has fallen into water. Unplug immediately.
• Check the power supply cord for damage before the frst use and during the life of the product.
• The supply cord cannot be replaced. If the cord is damaged the appliance should be scrapped.

To reduce the risk of burns, electrocution, fire, or injury to persons:

• If product is opened/disassembled for ANY reason, warranty is VOID.
• Do not use this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into any liquid. Contact Water Pik, Inc. or your local distributor which can be found at www.Waterpik.com.
• Do not direct water under the tongue, into the ear, nose or other delicate areas.
  This product is capable of producing pressures that may cause serious damage in these areas.
• Do not direct water into the nose or ear.
  The potentially deadly amoeba, Naegleria fowleri, may be present in some tap water or unchlorinated well water and may be fatal if directed into these areas.
• Use this product only as indicated in these instructions or as recommended by your dental professional.
• Only use fossing brush heads and accessories recommended by Water Pik, Inc.
• Do not drop or insert any foreign object into any opening or hose.
• Keep electrical cord away from heated surfaces.
• Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
• Fill reservoir with water or other dental professional recommended solutions only.
• Remove any oral jewelry prior to use.
• Do not use if you have an open wound on your tongue or in your mouth.
• If your physician or cardiologist has advised you to receive antibiotic premedication before dental procedures, you should consult  your dentist and/or medical professional before using this product or any other oral hygiene aid.
• Do not use iodine or water insoluble concentrated essential oils in this product.
  Use of these can reduce product performance and will shorten the life of the product. Use of these products may void warranty.
• Close supervision is necessary when this product is used by, on or near children or invalids.
• Magnetic feld: Pacemakers and similar implanted medical devices may be afected by magnet.
• Do not use the toothbrush motor for more than 5 minutes in each 10 minute period.
• Children should be supervised to ensure that they do not play with the appliance.
• This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug is intended to ft into a polarized outlet only one way. If the plug does not ft fully into the outlet, reverse the plug. If it still does not ft, contact a qualifed electrician.
  Do not attempt to modify the plug in any way.
• This product does not contain any user serviceable parts. Do not attempt to open except for battery disposal. See “Battery Removal” section.
• Using toothpastes containing peroxide may damage the plastic housing of this product.
• Using abrasive or chemical cleaners may damage the plastic housing of this product.
  IMPORTANT This device uses wireless communication to control the on/of function of the water fosser pump motor from the toothbrush power handle. This device was designed for Home or Ofce use. To avoid electromagnetic interference, do not operate this device in restricted locations such as aircraf or specially marked areas in hospitals.

SAVE THESE INSTRUCTIONS

PRODUCT DESCRIPTION

1. . Brush head
2. Water flosser nozzle
3. Hinged Lid
4. Reservoir
5. Water hose
6. Water flosser pressure control dial
7. Water hose release button
8. Toothbrush ON/OFF button
9. Motion activated ring lights*
10. Water flosser ON/OFF button
11. Power handle
12. Toothbrush charge indicator lights
13. Power cord
14. Charging base
15. Indicator Light

PREPARING THE UNIT / BRUSHING AND FLOSSING

Preparing the Unit

• Powering the Unit
  
  Plug the cord into an electrical outlet. If the outlet is controlled by a wall switch, be  sure it is turned on
• Attaching the Brush Head to the Power Handle
  
• Position the brush head on the power handle as shown. Press frmly until it clicks into place. To remove, frmly pull the brush head to separate it from the power handle.
• Attaching the Power Handle to the Hose
  
• Position the power handle onto hose in the base. Press the power handle frmly onto the hose attachment until it clicks into place. To remove, simply press the round button on the back side of the power handle.
• Charging the Sonic-Fusion®
  
• Charge for at least 20 minutes before frst use by placing the handle on the charging base. For a full charge, leave the handle on the charging base for at least 4 hours. A full charge should last 14 uses with a duration of 2 minutes each. If the toothbrush is to be stored for an extended period of time (six months or more), be sure to fully charge it (at least 4 hours) prior to storage.
• Charge Lights
  
• Toothbrush charge indicator lights will indicate level of battery charge for approximately 10 seconds afer removal from the charging base and afer use, and will then turn of. If only the bottom light is lit, then recharging is recommended to ensure uninterrupted use.
• Indicator Light
  
• The blue light blinks when: Light
  • The unit is frst plugged in
  • The handle is placed in charger
  • The handle is removed from the charger
  • A wireless command is received
• Preparing the Reservoir
  
  Remove reservoir and open hinged lid. Fill the reservoir with warm water. Close the lid and replace the reservoir on the base and press filmy.
• Prime Unit (First Time Use Only) Low
  
  Point the brush head tip into the sink. Press the Floss button and repeatedly rotate the pressure control dial between low and high until water fows. Afer water fows from the nozzle, press the FLOSS button to turn water OFF.
• Brush
  
  Place the brush head in your mouth before pressing the BRUSH button.
• Recommended Technique
  
  For best results, position brush along gumline at a 45-degree angle. Press the BRUSH button to turn the brush ON. Use light pressure and move the toothbrush slowly allowing for the sonic action to clean each tooth individually. Brush can be easily disconnected from the hose if desired (See diagram on product description page).
• Quad Timer
   
  The Sonic-Fusion® will create a short pause every 30 seconds to remind you to move to the next section of your mouth. You will brush the outside of the teeth for 30 seconds and then the inside for 30 seconds. This will be repeated on the other arch for a total of 2 minutes to clean all teeth.
• 2-Minute Timer
  The brush will automatically shut of afer 2 minutes of run time
• Floss
  
  Always place the brush head in your mouth prior to pressing the FLOSS button. Lean over the sink and slightly close lips enough to prevent splashing while still allowing water to fow from mouth into sink.
• Adjusting the Pressure Setting
  
  Turn the water fosser pressure control dial on the base of the unit to the lowest setting (pressure setting No. 1) for frst-time use. Gradually increase pressure over time to the setting you prefer – or as instructed by your dental professional.
• Recommended Technique
  For best results, start with the back teeth and work toward the front teeth. Direct the brush head so that the water fosser nozzle is angled slightly toward the gumline. Move the brush head along the gumline pausing briefy between each tooth to allow water to clean between teeth. Continue until you have cleaned the inside and outside of both the upper and lower teeth. When fnished, empty any liquid lef in the reservoir
  If you used mouthwash or any other solution besides water, see “Using Mouthwash and Other Solutions” section.
• Brush + Floss
  
  To Brush + Floss at the same time, place brush head in mouth. Press brush button, then press foss button.

CARE AND MAINTENANCE

• Travel and Hose-Free Brushing
  
  Toothbrush can be disconnected from the Sonic-Fusion® for travel or hose-free brushing. Place the handle and desired brush head(s) in the provided case for protection when traveling.
  To disconnect the toothbrush from the water hose, press the round button on the back side of the power handle.
• Using Mouthwash and Other Solutions
  
  Your Waterpik® Sonic-Fusion® can be used to deliver mouthwash and antibacterial solutions. Afer using any special solution, rinse unit to prevent clogging by partially flling reservoir with warm water and running unit with brush head pointed into sink.

Care and Maintenance
Before cleaning, unplug from the electrical outlet.

After Each Use
 

1. Afer each use, when all functions are turned OFF, remove the brush head from the handle and rinse brush head and handle under running water.
2. Wipe the handle dry afer each use.
3. Store handle on charger and keep unit plugged in.
   The unit will not overcharge.

General Cleaning / Removing Hard Water Deposits

• Clean the product when necessary by using a sof cloth and mild non-abrasive cleanser.
• Hard water deposits may build up in your unit, depending on the mineral content of your water. If lef unattended, it can hinder performance. Cleaning internal parts: add 2 tablespoons of white vinegar to a full reservoir of warm water. Point the handle and brush head into sink. Turn Water Flosser ON and run until reservoir is empty. Rinse by repeating with a full reservoir of clean warm water.
  This process should be done every 1 to 3 months to ensure optimal performance.

  Toothbrush Low Charge Lock Out

The toothbrush charge indicator lights will fash if the battery charge is too low for brushing. This may cause the toothbrush to enter Lock Out mode. To clear the Lock Out, place the power handle on the charging base.

Leakage
If leaking due to a damaged hose, replacement hoses can be purchased at www.waterpik.com or contact Water Pik Inc. customer service for a self service repair kit.

Multiple Unit Proximity

To avoid wireless communication interference when more than one unit will be used in proximity, go to (waterpik.com/MUP) for instruction for changing the base and handle ID.

Battery Removal

This product contains rechargeable Nickle Metal Hydride batteries.
The batteries are not replaceable. Please do not dispose of the unit in the household waste. Remove the batteries per the instructions below and recycle at your local recycling center
This process is not reversible Remove the battery only at the end of the product’s life for recycling. Doing so earlier will destroy the product. Deplete the battery charge until the brush no longer operates. Observe basic safety precautions to protect your eyes, hands, fngers, and work surface. Remove the batteries as shown and recycle them and the rest of the product according to local regulations

1. Run down the battery by operating the brush button until the motor does not run.
2. Obtain a towel or cloth, hammer, fat-head screwdriver, and wire cutters.
3. Remove and discard the brush head.
4. Cover the handle entirely with the towel or cloth.
5. Clamp the top of the handle against your work surface with one hand and strike the handle housing around the bottom perimeter on all sides to release the end cap latch. Continue striking and rotating the handle until the end cap releases.
6. Remove the internal components by turning the handle upside down and while holding on to the handle housing, press the shaf down frmly on a hard surface.
7. The internal components should slide out when the handle is positioned upside-down. If this does not occur, repeat steps 5 and 6 until the components release.
8. Remove the end cap from the internal assembly.
9. Slide the battery out of the internal assembly.
10. Cut the battery wires one at a time with the wire cutters.
11. Recycle and dispose of the battery properly.
12. The remaining product pieces should be discarded appropriately.

LIMITED THREE YEAR WARRANTY

Service Maintenance
Waterpik® Sonic-Fusion® have no consumer-serviceable electrical items and do not require routine service maintenance. For all accessories go to www.waterpik.com.
You may also call our toll-free customer service number at 1-800-525-2774. Refer to the serial and model numbers in all correspondence. These numbers are located on the bottom of your unit.
Still have questions? Go to www.waterpik.com.

Still have questions? Go to www.waterpik.com.
Water Pik, Inc. warrants to the original consumer of this product that it is free from defects in materials and workmanship for 3 years from the date of purchase.
Consumer will be required to submit the original purchase receipt as proof of purchase date and if requested, the entire product, to support a warranty claim. Water Pik, Inc. will replace, at its discretion, the product which in its opinion is defective, provided the product has not been abused, misused, altered or damaged afer purchase, was used according to instructions, and was used only with accessories or consumable parts approved by Water Pik, Inc. This limited warranty excludes accessories or consumable parts such as tips and brush heads. This warranty gives you specifc legal rights. You may also have other rights that vary, depending on the law in your place of residence

Arbitration

BINDING ARBITRATION AND WAIVER OF RIGHT TO ASSERT MATTERS IN COURT AND RIGHT TO JURY TRIAL
By purchasing, installing, or using this product you agree that any controversy or claim arising out of or relating to your purchase, use, modifcation, installation,
or removal of this product shall be settled by binding arbitration. The arbitrator’s decision will be fnal and binding. Judgment on the award rendered by the arbitrator may be entered in any court having jurisdiction over the matter. Further, you agree that you will not have the right to litigate any claim arising out of or in relation to your purchase, use, modifcation, installation, or removal of this product in any court or to have a jury trial on that claim.
Arbitration of any matters shall be administered by the American Arbitration Association and conducted by one arbitrator in accordance with the consumer arbitration rules of the American Arbitration Association in efect at the time of
fling of the demand. The venue for all such arbitrations shall be Colorado and any such arbitration shall be subject to the Federal Arbitration Act and Colorado law.

WAIVER OF RIGHT TO PARTICIPATE IN CLASS ACTIONS OR PURSUE CLAIMS IN A REPRESENTATIVE CAPACITY.

Further, by purchasing, installing, or using this product you agree that arbitration must be on an individual basis. This means neither you, nor we, may
join or consolidate claims in arbitration by or against other purchasers or users of Waterpik® products or the general public.

Additionally, you may not litigate in court or arbitrate any claims as a representative or member of a class or in a purported representative capacity on behalf of the general public, other purchasers or users of this product, other persons or entities similarly situated, or in a private attorney general capacity.

Limitation of Liability
This limited warranty is your sole remedy against Water Pik and it shall not be liable for any damages, whether direct, indirect, incidental, special, consequential, exemplary or otherwise, including but not limited to property damage, arising out of any theory of recovery, including statutory, contract or tort.

For USA Only
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: changes or modifcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment of and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 18 of the FCC Rules.

For Canada Only
This device complies with Industry Canada’s license-exempt RSSs. Operation is
subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device