Bontrager Transmitr MicroRemote

1. Twist anticlockwise to open the remote. Keep the top half assembled.
2. Pull out the battery activation tab.
3. Twist the remote clockwise to close.

A note about pairing
Up to four ANT+ compatible lights can be paired to the Transmitr MicroRemote in a single pairing session. Once in pairing mode, the remote will automatically search for each activated light, to pair one at a time, in sequence. The pairing process is the same for all ANT+ compatible lights, regardless of whether it’s a front light or a rear light.

NOTE: All lights must be paired in the same continuous procedure. If you choose to add a light later, you will need to pair each light again at that time.

1. Before starting, place the remote and all lights within 15 cm (6 inches) of each other.

        NOTE: Move 4.5 metres (15 feet) from other ANT+ compatible lights to prevent accidental pairing.

2. For all lights you wish to pair, turn on each light then quickly turn it off again.
   NOTE: After completing this step, do not press the power button on the light again until pairing is complete.

3. Press and hold the button on the remote for at least 15 seconds. Position your thumb on the remote button so you can see the red light flash under the button. Release the button when the green/red light begins to flash.

NOTES: Upon entering the pairing process, all previously stored pairing is removed.
If a light is accidentally paired, start the pairing process again.

4. While the remote searches for a light, the LED flashes red. When the remote finds a light, the LED will change from a red flash to a green flash and the found light will turn on.
5. While the remote is still flashing green, single-press the button on the remote. The LED will begin flashing red again to find another available light to confirm you have paired the correct light.
6. Repeat steps 4 and 5 for each light to pair.
7. To exit pairing, single-press the button while the remote is flashing red. If pairing to 4 lights, the remote will exit pairing mode automatically after the fourth light is paired.

       NOTE: Waiting at any time for 10 seconds will also end the pairing process automatically.

A small ANT+ and Bluetooth wireless remote that’s easy to pair and makes on-bar control of bicycle lights a breeze. The versatile remote mounts to both road or MTB bars and can be paired with up to 4 lights.

IMPORTANT: To use the Transmitr MicroRemote, you must have ANT+ compatible lights mounted on your bicycle.

Compatible Bontrager lights:
• Ion Pro RT
• Ion 200 RT
• Ion 450 RT
• Flare RT
• Ion 800 RT
• Ion 700 RT
• Ion 350 RT
• Other ANT+ compatible lights

To set up any other light, please refer to the manual that came with your light.

There are two phases to this installation: pairing the lights to the remote and attaching the lights and remote to the bike. It is easiest to pair the lights to the remote before attaching it to the bike.

1. Double-click the remote button to turn on all paired lights.
2. Press and hold the remote button for 1 second to turn off the light(s).

When the Transmitr MicroRemote is used while lights are being used in auto mode with a Garmin, the remote will take over changing the mode to individual on the Garmin. If a user wants auto mode to function again, they’ll need to select it again on the Garmin.
The remote will recognise available lights within 30 m (100 ft) as long as there is a clean line of sight.

• All lights will require a double-click to turn on.
• Once on, a single-click will change the mode of the front light, depending on the light type. A long press will turn the lights off if they are on.
• The front light will operate in two configurations: High Mode Control or Mode Selection. The default out-of-the-box experience is High Mode Control.
• The rear lights will only turn on and off.

Each light will turn on to the last mode it was in when the remote turned the light off.

High mode control
If there is no saved mode, the light will turn on to LOW. Subsequent button presses will alternate the light between HIGH and the previous mode.

Mode selection
By default, if there is no saved state, the lights will turn on to LOW. After this, each button press will advance the lights through the mode list.
Example: High (click) -> Medium (click) -> Low (click) -> Night Flash (click) -> Day Flash

Change front light control mode
Hold down the button for 8 seconds. If you release the button between 8 and 15 seconds, the remote will switch to the new control mode. It will flash to indicate which mode the remote is in: Red = High Mode Control; Green = Mode Selection.
NOTE: If you do not release the button before 15 seconds, the remote will enter pairing mode.

Rear lights
The default setting is LOW. To change the saved mode, turn on the light. Use the button on the rear lights to change the mode, then turn off the system using the remote.
Can’t find light
If you are attempting to interact with a light and the remote can’t find it, the remote will flash red for 2 seconds. And you must repeat the pairing process.
Low battery
If the battery on one of your lights has fallen below 5%, the remote lights up solid red for 2 seconds. This will happen only when turning the system on, or turning the system off.

Attach the remote

The following attachment methods allow you to install the Mirco Remote on a variety of handlebar configurations. The strap will wrap securely around diameters as small as 22.2 mm up to the hoods on a road brake/shift lever.

• 22.2 mm diameter near the grips.

• 31.8 mm at the centre of a road bar.

• Aero section of a road bar.

• Below the brake/shift lever hood on a road bike.

• Optional: Use the bar-end plug adaptor for the end of the handlebar installation. Sold separately. PN W588932.

The battery is not rechargeable. It uses a coin-type CR1632 battery.

Battery installation

1. Twist the button assembly anticlockwise to remove it from the housing and strap assembly.
2. Push the button assembly out of the top cover.
3. Slide the old battery out and dispose of properly.
4. Slide the new battery into the battery carrier. Be sure to have the plus (+) side facing you.
5. Press the battery and button assembly back into the top housing cover.
6. Twist the button assembly clockwise a quarter-turn onto the housing and strap assembly.

The small tabs should align when correctly assembled.

Statements of Regulatory Compliance

FCC Compliance Transmitr MicroRemote – FCC ID: 2AHXD-563210
These devices comply with part 15 of the FCC Rules.
Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or experienced radio/TV technician for help.

NOTE: TREK BICYCLE CORPORATION IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORISED MODIFICATIONS TO THIS EQUIPMENT. ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER OF THIS DEVICE COULD VOID THE USER’S AUTHORITY TO OPERATE THE DEVICE.

Bontrager Transmitr MicroRemote – (P/N 563210), CAN ICES-3(B)/NMB-3(B) IC: 21334-563210
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This Bontrager equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. The radiated output power of the Transmitr Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. This equipment is in direct contact with the body of the user under normal operating conditions. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Status of the listing in the Industry Canada’s REL (Radio Equipment List) can be found at the following web address: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng

Additional Canadian information on RF exposure also can be found at the following web address: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

Transmission Frequency: 2.4GHz
Bluetooth: 2402MHz ~ 2480MHz
ANT+: 2457MHz
Bluetooth Max Power: <6dBm
ANT+ Max Power: <6dBm
Operating power: 3 V D C
Operating temperature: 0ºC ~50ºC
RF exposure compliance distance is 20 millimetres.

Trek Bicycle Corporation and Bontrager hereby declare that the wireless devices identified as Transmitr MicroRemote is in compliance with the following European Directives:

• R&TTE Directive 1999/05/EC – RED 2014/53/EU
• EMC Directive 2004/104/EC – EMCD 2014/30/EU
• LVD Directive 2006/95/EC – LVD 2014/35/EU
• RoHS Directive 2011/65/EU The full text of the EU declaration of conformity is available from your dealer, or at the following internet address: http://www.bontrager.com/support
• RoHS Directive 2015/863/EU

WARNING!

• Keep batteries away from children.
• If the battery closure does not function, do not use the product.
• If a battery is swallowed or inserted into the body, seek medical help immediately.

Warranty
The Bontrager Transmitr MicroRemote is covered by a warranty. For details, visit www.trekbikes.com

Trek Bicycle Corporation contact information:
North America
Trek Bicycle Corporation
801 West Madison Street
Waterloo, WI 53594 USA
Tel: 800-313-8735
Europe
Bikeurope BV
Ceintuurbaan 2-20C
3847 LG Harderwijk
The Netherlands
Tel: +31 (0)88 4500699
Australia
Trek Bicycle Corp. Au.
8 Townsville Street (Level One)
Fyshwick (ACT) 2609 AU
Tel: +61 (02) 61 732 400

About this manual

This manual is for Bontrager lights Ion Pro RT, Ion 200 RT (headlights) and Flare RT (tail light). RT indicates light is rechargeable and remote controllable when paired with Bontrager Transmitr remote, PN 502865, or another ANT+ compatible device.

WARNING

The light may be hot and could cause a burn or damage material it may contact. Do not activate (turn on) light in enclosed area. Avoid accidental wireless activation.

Please read the additional Warning, page 2, before using this light.

Specifications

• Ion Pro RT: 4800 mAh, 3.6 Vdc, 17.3 Wh, lithium Ion battery
• Ion 200RT and Flare RT: 420mAh, 3.7 Vdc, 1.6 Wh lithium polymer battery

For more information

If you need help not offered by this manual, talk to your Bontrager retailer or visit trekbikes.com.

Basic operation (see Table 1)

• To turn on, double click (Ion Pro RT) (similar to a computer mouse) and single click (Ion 200 RT / Flare RT) the power button.
• To turn off, press and hold the power button. To change mode, quick-press the power button.

NOTE: When turned on Ion Pro RT, Ion 200 RT and the Flare RT will return to the last active mode.

Table 1. Modes, runtime, and battery life

Battery charging and care (see Table 2)

Although the light is charged at the factory, it is recommended to charge it before first use.

To charge the battery

IMPORTANT: For best results, charge at room temperature in a dry place. Use a quality CE or UL approved USB charger rated for 500 mA or greater. Avoid extreme conditions including wet, cold, or extremely hot.

• Open the USB port cover.
• Plug the Micro charger cable into the USB port on the light.
• Plug the cable into a computer or wall adapter.
• When the charge is complete, unplug the Micro charger cable and close the USB port cover.

IMPORTANT: Ensure the USB cover is latched before riding in rain or in wet conditions. If the USB cover is not closed, damage to the light may occur.

Table 2. Battery charging and care

• Flashes fast (2 Hz) with 4 wire USB cable and a 500mA charger, or slow (1 Hz) with 2 wire USB cable
• When fully charged, status led remains steady for 1 minute then turns off
• Requires a 4 wire USB cable, supplied, and a 500mA charger

List of parts

You may have purchased one or more of the following lights.

Accessories (purchase separately)

Caring for the battery

Store the light at room temperature in a dry place. Avoid moisture, or extreme hot or cold.

Store the light in the charged condition. Avoid ‘deep discharge’. Battery life will decrease if the battery is stored in a fully discharged condition.

Over time, the run time of the battery will diminish. Expect about 500 full charges, depending on care. After a full life, the battery will continue to charge but with a lower run time. When the run time is unsatisfactory, do not open the case of the light or incinerate; please recycle.

Traveling with the battery

Li-ion batteries cannot be shipped by air due to airline regulations. When traveling by air, place the light in your carry-on.

Recycling

Please recycle the battery. In the US, you can find out where to do this at www.call2recycle.org

This symbol on the product(s) and / or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, outside the US, please take this product(s) to designated collection points. Alternatively, in some countries you may be able to return your products to your local retailer upon purchase of an equivalent new product.

Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation.

Ion Pro RT information, installation, and special features

Installation

1. Loosen knob and open.
2. Adjust for bar size (31.8mm or 35mm).
3. Close and tighten knob.
4. Slide light onto mount until it locks in place.
   NOTE: Use provided shim to fit 25.4 bars.
   Removal
5. Press down.
6. Slide light to remove.

Low battery feature

When the battery charge drops below 5% the light automatically adjusts the output brightness to 50 lumens. This extends the light output for an additional 30 minutes.

Locking/Unlocking the mode

Turn on and select the desired mode, then press and hold the power button 8 seconds to select it. The light will turn off and the main LED will flash once. To unlock, repeat the process.

Reset

To reset the light to factory default settings, with the light on, press and hold the power button for 15 seconds. The main LED will flash once at 8 seconds, and again at 15 seconds. Release the button after the second flash.

Wireless Communication

The light is shipped with ANT+ and Bluetooth wireless connectivity enabled. To disable, with the light off, press and hold the power button for 15 seconds. The main LED will flash once at 8 seconds, and again at 15 seconds. Release the button after the second flash.

NOTE: The status LED flashes blue every 15 seconds when wireless is enabled.

Pairing to the Transmitr Remote, Bontrager Garmin Edge® GPS computer or select Garmin Edge® computers

The Transmitr Remote (or select Garmin Edge computers, sold separately) allows remote control of the light. This feature is only available on the Ion Pro RT, Ion 200 RT, and the Flare RT as well as other compatible Transmitr lights.

For more complete instructions, refer to the Transmitr manual at trekbikes.com. For Garmin related instruction and a complete listing of compatible Edge devices visit support. garmin.com.

Before starting, place the remote and all lights within a small area. Move 15 feet from other Transmitr / ANT+ compatible lights to prevent unintentional pairing. If a light is unintentionally paired, restart the pairing process at the beginning.

NOTE: All pairings must be done in a single session. After pairing is finished, pairing any additional lights will require that you repeat the entire pairing procedure.

• Place the light close to the Transmitr Remote (within 15cm / 6in).
• Quick-press the power button on the light to turn it on, then quick-press to turn it off again.
  NOTE: After completing this step, do not press the power button on the light again until pairing is complete.
• Press-and-hold the center button on the Transmitr Remote for at least 8 seconds. When the corner buttons flash, release the center button.
• While the remote searches for a light, its center button flashes red. When the Transmitr Remote finds a light, the center button on the remote will change from red to green, and the found light will flash.
• While the found light is still flashing, quick-press the button on the Transmitr Remote to which you would like to pair the light. The selected button will glow, and the found (paired) light will stop flashing and turn off.                                                                   NOTE: After the pairing, the center button on the remote will flash red until the Transmitr Remote finds another available light.
• Repeat Step 4 and Step 5 for each additional light to be paired.

To exit pairing

• When all lights are paired, quick-press the center button on the remote. The
  button will stop flashing and turn off.

To verify pairing

1. Quick-press the center button on the remote to turn on all paired lights.
2. Press-and-hold the center button to turn off all of them.
3. Turn on each light individually. Quick-press each paired corner button on the
   remote to turn on the individual light(s).
4. Press-and-hold the same corner button to turn off the light.

Using the Transmitr Remote

To turn on all lights

• ON: Quick-press the center button.
• OFF: Press and hold the center button.

To turn on an individual light

• ON: Quick-press the corner button that controls the light.
• OFF: Press and hold the same button.

To change modes of an individual light

Each quick-press of a button that controls a light will cycle through the modes.

To see battery power status on the remote

When a corner button is pressed, the center button will show the battery status of the light.

Ion 200 RT information, installation, and special features

Installation

To attach with the Quick Connect 0˚ offset bracket

• Place the quick connect on the handlebar with the hook in front.
• Stretch the strap under the bar and connect to the hook.
  NOTE: Use the second hook to latch excess strap.
• Slide the Ion 200 RT onto the bracket until it clicks. The power button should be facing up and the lens of the light should be perpendicular to the road.

Removal

Press down on the tab and slide the light away from the lever. Alternatively, you can remove the entire quick-connect bracket, with the light attached.

Low battery feature

When the battery charge drops below 5% the light automatically adjusts the output brightness to 5 lumens. This extends the light output for an additional 30 minutes.

Locking/Unlocking the mode

Turn on and select the desired mode, then press and hold the power button 8 seconds to select it. The light will turn off and the main LED will flash once.

To unlock, repeat the process.

Auto brightness

The light is shipped with an ambient light sensor enabled. The light automatically changes modes with ambient light conditions. It changes from Day Flash to High Steady. To disable, with the light off, press and hold the power button 8 seconds. The light will flash once.
NOTE: When auto brightness is enabled, all modes are manually accessible.

Reset

To reset the light to factory default settings, with the light on, press and hold the power button for 15 seconds. The main LED will flash once at 8 seconds, and again at 15 seconds. Release the button after the second flash.

Wireless Communication

The light is shipped with ANT+ and Bluetooth wireless connectivity enabled. To disable, with the light off, press and hold the power button for 15 seconds. The main LED will flash once at 8 seconds, and again at 15 seconds. Release the button after the second flash.
NOTE: The status LED flashes blue every 15 seconds when wireless is enabled.

Flare RT information, installation, and special features

Installation

To attach with the Quick Connect 16˚ offset bracket.

IMPORTANT: The seatpost/saddle icon shows that the lens is oriented perpendicular to the ground to optimize visibility.

NOTE: Use the second hook to latch any excess strap.

To attach to a seat pack

Attach the seat pack clip to the bag loop. To optimize visibility, ensure the light lens is oriented perpendicular to the ground.

To attach to a rack

Remove the quick connect clip from the rubber strap and attach to a rack with a M5 bolt and washer, sold separately, PN 537061.

Low battery feature

When the battery charge drops below 5% the light automatically adjusts the output brightness and begins to flash. This extends the light output for an additional 30 minutes.

Locking/Unlocking the mode

Turn on and select the desired mode, then press and hold the power button 8 seconds to select it. The light will turn off and the main LED will flash once. To unlock, repeat the process.

Auto brightness

The light is shipped with an ambient light sensor enabled. The light
automatically changes modes with ambient light conditions. It changes from Day Flash or All Day Flash to Night Flash, OR Day Steady to Night Steady. To disable, with the light off, press and hold the power button 8 seconds. The light will flash once.
NOTE: When auto brightness is enabled, Day Flash, All Day Flash and Day Steady are manually accessible.

Reset

To reset the light to factory default settings, with the light on, press and hold the power button for 15 seconds. The main LED will flash once at 8 seconds, and again at 15 seconds. Release the button after the second flash.

Wireless Communication

The light is shipped with ANT+ and Bluetooth wireless connectivity enabled. To disable, with the light off, press and hold the power button for 15 seconds. The main LED will flash once at 8 seconds, and again at 15 seconds. Release the button after the second flash.
NOTE: The status LED flashes blue every 15 seconds when wireless
is enabled.

WARNING

A bicycle without correct lights and reflectors might be difficult for other people to see, and you might not be able to see. If you cannot see, or other people cannot see you, you could have an accident. Make sure your lights operate correctly and that batteries are charged.

European Union Compliance

Ion Pro RT and Ion 200 RTdo not comply with German StVZO regulations! Trek Bicycle Corporation and Bontrager hereby declare that the wireless device identified as ‘Ion Pro RT’, ‘Ion 200 RT’ and ‘Flare RT’are in compliance with the following European Directives:

• Radio Equipment Directive 2014/53/EU (Ion Pro RT only)
• EMC Directive 2014/30/EU
• Low Voltage Directive 2014/35/EU (Ion Pro RT only
• RoHS Directive 2011/65/EU

The full text of the EU declaration of conformity is available from your dealer, or at the following internet address: http://www.trekbikes.com/support