EXTREME STEAM™ FABRIC STEAMER with DUAL HEAT

Instruction Booklet

Model GS23

For your safety and continued enjoyment of this product, always read the instruction book carefully before using it.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially when children are present, basic safety precautions should always be taken, including the following:
READ ALL INSTRUCTIONS BEFORE USING
DANGER – Any appliance is electrically live even when the switch is off.
To reduce the risk of death by electric shock:

1. Always unplug the appliance immediately after using.
2. Do not place or store appliances where they can fall or be pulled into a tub or sink.
3. Do not place in, or drop into water or other liquids.
4. If an appliance falls into water, unplug it immediately. Do not reach into the water.

WARNING – To reduce the risk of burns, electrocution, fire, or injury to persons:

1. This appliance should never be left unattended when plugged in.
2. Close supervision is necessary when this appliance is used by, on, or near children or individuals with certain disabilities.
   Unsupervised use could result in fire or personal injury.
3. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
4. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been dropped or damaged, or dropped into water. Do not attempt to repair the appliance. Incorrect reassembly or repair could cause a risk of fire, electric shock, or injury to persons when the appliance is used. Return the appliance to an authorized service center for examination and repair.
5. Keep the cord away from heated surfaces.
   Do not allow the cord to contact heated surfaces.
   Do not pull or twist the cord. Let the appliance cool completely before putting it away. Loop cord loosely around the appliance when storing.
6. This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
7. Never drop or insert any object into any opening.
8. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
9. Do not use an extension cord to operate the appliance.
10. The surfaces of this appliance may be hot when in use. Do not let heated surfaces touch eyes or skin.
11. Do not place the steam nozzle directly on any surface or on the appliance power cord while it is hot or plugged in.
12. Unplug this appliance before filling or emptying. Do not overfill.
13. Do not operate the steamer without properly filling the water container.
14. Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect.
15. Burns could occur from touching hot parts, hot water, or steam. Use care when removing the water reservoir or when you turn a steam appliance upside down – there may be hot water in the reservoir. Always position the steamer heads away from you and any other person when turning on.
16. To reduce the likelihood of circuit overload, do not operate another high wattage appliance on the same circuit.
17. When installing or removing attachments, please be sure the unit is off and no steam is being released to avoid contact with hot water.
18. Use caution when installing or removing an attachment as it may contain hot water from condensation. Ensure that the attachment is dry or cooled off to avoid contact with hot water.

SAVE THESE INSTRUCTIONS

IMPORTANT
FOR HOUSEHOLD USE ONLY

FILLING INSTRUCTIONS

1. Place the unit on its back on a flat and stable surface.
   
2. While holding the water reservoir with one hand, move the release switch up toward the steam head nozzle.
3. Pull the reservoir out, away from the body.
4. Turn the reservoir over, revealing the rubber inlet cover.
5. Open the inlet cover and fill the reservoir with everyday tap water (filtered water may reduce hard water problems).
6. Close the inlet cover and return the reservoir to its place, making sure that it is secure.

GETTING TO KNOW YOUR STEAMER

OPERATING INSTRUCTIONS

1. Plug the unit into the electrical outlet.
2. The power light will light up (red). Allow one or two minutes for the unit to warm up. The appliance is ready to use when the ready light goes on  (green).
3. Holding the steam jets away from you and anyone else in the room, engage the trigger. Steam should now be released from the steam jets. To have continuous steam, just move the switch down so you will have continuous steam without having to hold the trigger. Always have steam facing away from you or anyone in the room.
4. When first using the device, test on an old cloth, as there may be sediment left from the manufacturing process or transportation.
5. On the back of the steamer, there is a sliding switch for high and low settings. High is for heavier and badly wrinkled fabric and provides faster, hotter,  less visible steam. The low setting should be used for delicate fabrics like silk, in combination with a soft cushion brush attachment. To stop the flow of steam, release the trigger or lower the switch.
6. Unplug the device when it is not in use.

STEAMING TIPS

1. To prepare your fabric for steaming, brush it with the soft cushion brush attachment. This will loosen the fibers and allow better steam penetration.
2. Hang your garment or fabric.
3. Pass the steam jets just above the fabric where the wrinkles are. It may take a few passes to remove the wrinkles completely.
4. After use, unplug the steamer and empty any remaining water from the tank to avoid leakage.
5. CAUTION: When hanging garment on a door while steaming, be careful not to damage the door with steam

Conair will repair or replace (at our option) your appliance free of charge for 12 months from the date of purchase if the appliance is defective in workmanship or materials.

To obtain service under this warranty, return the defective product to the service center listed on the back, together with your sales slip and $7.00 for postage and handling.  California residents need only provide proof of purchase and should call 1-800-3-CONAIR for shipping instructions. In the absence of a purchase receipt, the warranty period will be 12 months from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE  IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 12-MONTH  DURATION OF THIS WRITTEN, LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

For information on any Conair products, call 1-800-3-CONAIR or visit us on the web at www.conair.com
Please register this product at: www.conair.com/registration
©2011 Conair Corporation
East Windsor, NJ 08520
Glendale, AZ 85307
Made in China
11PA121686
IB-10893

CONAIR INFINITI Pro Curl Secret 2.0 User Guide

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially when children are present, basic safety precautions should always be taken, including the following:

READ ALL INSTRUCTIONS BEFORE USING KEEP AWAY FROM WATER

DANGER:
Any appliance is electrically live even when the switch is off. To reduce the risk of death by electric shock.

1. Always unplug appliance immediately after using.
2. Do not use while bathing or in the shower.
3. Do not place or store appliance where it can fall or be pulled into a tub or Sink.
4. Do not place in, or drop into water or other liquids.
5. If an appliance falls into water, unplug it Do not reach into the water.

WARNING
To reduce the risk of burns, electrocution, fire, or injury to persons:

1. This appliance should never be left unattended when plugged in.
   2. Do not pull, twist, or wrap line cord around appliance.
   3. This appliance should not be used by, on or near children or individuals with certain disabilities.
   4. Use this appliance only for its intended use, as described in this Do not use attachments not recommended by the manufacturer.
   5. Never operate this appliance if it has a damaged cord or plug, if it is not working properly or if it has been dropped or damaged, or dropped into water. Return the appliance to an authorized service center for examination and repair.
   6.  Keep the cord away from heated surfaces.
   7. Never use while sleeping.
   8. Never drop or insert any object into any opening or hose.
   9. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
   10. Unit is hot when in use. Do not let heated surface touch eyes or skin.
   11. Do not place the heated unit directly on any surface while it is hot or plugged in.
   12. Never block the air openings of the appliance or place on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of hair, lint and other debris.
   13. Do not use an extension cord with this appliance.
   14.  Do not touch hot surfaces of the appliance. Use handles or knobs.
   15. Do not attempt to touch the housing of your appliance near the curl chamber, as it is hot when in use.
   16. Do not operate with a voltage converter.
   17. This appliance is not a toy. Keep away from children.

OPERATING INSTRUCTIONS

This styler is intended for household use. Use on Alternating Current (60 Hz) only. This unit is designed to be operated at 120V AC. This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

GETTING STARTED

The secret to Curl Secret® 2.0 is how easy it makes creating the perfect curl – a tight spiral, a big, loose curl, even a relaxed wave – one after another! Hair goes in, curl comes out. It’s that simple. First, decide what type of curl you’d like – spirals or tighter curls, which can be shaped into a vintage chic style, or bigger curls or relaxed waves, which are beautiful on their own, and can be tousled into a natural, “undone” look. For spirals or tighter curls, choose the smaller, 1-inch attachment, the high heat setting and the 12- or 14-second timer setting. For a looser curl or wave, we recommend the larger 1¼-inch attachment, the low setting and the 8- or 10-second timer setting. As you use this innovative, new styler, you’ll discover the settings that let you best create the curls you want.

• Always change or remove attachments before plugging the appliance in and switching it on.
• To remove the attachment, press the two buttons on the two sides of the attachment at the same time, using your thumb and index finger.
• To position the attachment, place it onto the appliance head until it clicks in.
• Plug in the appliance, switch on, and select the desired temperature using the OFF/LOW/HIGH switch. See table below:

• The indicator light comes on and will start to flash.
• The indicator light will stop flashing when the appliance has heated up to the selected temperature. The appliance is now ready to use; the indicator light will stay on.
• Select the time setting, depending on the desired curl effect. For loose curls, select the minimum time setting. For tighter curls, select the maximum time setting. Please refer to the table below:

• Select the adjustment of the direction of the curl, according to the desired result:
  • For an even, more sophisticated style, adjust the appliance to the “L” (left) position, to create curls on the left side of the head. Then adjust the appliance to the “R” (right) position, to create curls on the right side of the head.
  • For a softer, more natural style, adjust the appliance to the “A” (automatic) position. This adjustment will create alternating curls, first in one direction and then the opposite.
    

WARNING: The styler’s titanium ceramic-coated curl chamber will get very hot within a few seconds and should not be placed in contact with the skin after the styler has been turned
on.

TO CURL HAIR

Hair should be clean, completely dry and combed before you use the curling device.

1. Begin by carefully combing through hair to smooth it. Then take a ½-in. to 1-in. section (Fig. A).
   
2. Please note the styler must be positioned into the hair with the opening of the curl chamber facing toward the head (Fig. B).
   
3. Position the styler where you want the curl to start. The hair section must be straight, and placed neatly through the center of the hair guide
   (Fig. C and D).
   
   
   
4. Once the hair is in place, let go of the hair section and close the handle to allow the hair to be automatically taken into the curl chamber (Fig. E).
   
5. Open the Curl Secret® 2.0 and gently pull it away from the head to release a perfect curl (Fig. F)!
   
   Let it cool in place for a minute to set the curl. Quick heat-up and recovery, and Curl Secret® 2.0’s fully automatic curling technology let you make consistently perfect curls – one after another – effortlessly! It’s a revolutionary new way to curl your hair. Fast, easy, and always perfect, curl after curl

• The hair is automatically drawn into the ceramic curl chamber, where it is softly held and heated from all directions to effortlessly form the curl.
• If you are using the timer setting, the automatic beep indicator will start as soon as the handles are closed together. There will be a series of individual beeps. Hold the styler still, with the handles held together, until the end of the individual beeps. The amount of beeps will depend on the chosen timer setting. This indicates that the time is up and you can remove the styler from your hair.

NOTE:
Always release the handles first to set the curl free; if you pull away before you open the handles, the curl will be straightened out.
• To allow the curl to set, do not comb or brush the hair until it cools.
• Repeat around the head until you have the amount of curls desired.
NOTE:
Do not use this styling appliance on hair extensions.

ADDED FEATURES

Curl Secret® 2.0 comes with 4 functions for added safety and energy savings:
Anti-Tangle Feature: Curl Secret® 2.0 is safe and easy to use when used properly. However, should improper use occur, the anti-tangle feature has been designed to immediately stop drawing the hair in and will reverse to a neutral position. Simply open the handles and ease hair out of the curl chamber.
Auto Shut-Off: If the appliance is switched on for more than 60 minutes continuously, it will automatically switch off. If you wish to continue using the appliance, simply slide the switch to the OFF position and then slide the switch to the relevant setting to turn the power on.
Sleep Mode: Energy efficient – after 20 minutes of idle time, temperature drops to around 150˚C/300˚F.
Motion Sensor: Ends sleep mode and reheats to selected temperature when handle is closed.
NOTE: Curl chamber will be hot to the touch.
NOTE: Curl Secret® 2.0’s new brushless motor technology uses magnets instead of brushes to sense any change in speed, and turns itself off as an added safety feature and to ensure tangle-free curling action. Minimizes weight, maximizes curl control, and significantly extends the life of your appliance.
NOTE: If you continue to hold the hair section after closing the handle, Curl Secret® 2.0 will stop and beep to indicate that you must release the tension on the hair. If you have taken too much hair, or hair is not neatly going through the center of the appliance, the Curl Secret® 2.0 will again stop and beep to indicate a problem. This safety feature ensures there will be no tangles.

MOST IMPORTANT: If hair does get tangled, unplug the unit and gently work the hair out of the unit. Take very small strands, one at a time, and slowly remove from the chamber. If hair is tight around the barrel, carefully and gently loosen up hair outside of the tool with your fingers, removing small sections at a time. Make sure fingers do not come in contact with heated chamber.

GETTING TO KNOW YOUR CURL SECRET

Effortlessly create long-lasting, beautiful curls. Hair is automatically drawn into the titanium ceramic Curl chamber where it is softly held and heated from all directions to effortlessly form the curl. Then, simply release. The result is beautiful, free-flowing curls.

Features:

• 1-in. and 1¼-in. interchangeable chambers
• 3 curl directions/6 timer settings
• Brushless motor for precision styling and longer life
• Auto beep indicator
• Ion generator
• Safety tangle feature
• 30-second instant heat
• Sleep mode
• Motion sensor
• Auto off
  

IONIC TECHNOLOGY

Many aspects of modern living, including air conditioning, contact with man-made fibers and air pollution, contribute to a buildup of static electricity in the hair. Even brushing and towel-drying the hair can increase these levels, causing the surface of the cuticle to become rough. Consequently, hair may have a dull appearance. Also, high levels of static charge cause hair to become flyaway and difficult to style.
The ion generator produces a stream of negative ions that act to neutralize the static charge, smoothing the scales on the cuticle for shiny, smooth and manageable hair, so you can achieve your desired style easily.

NOTE: The unit may produce a clicking sound at times, which is normal for a high-output ion generator.

THE NEW TITANIUM CERAMIC EASY-GLIDE STYLER

The Curl Secret® 2.0 has a titanium ceramic, easy-glide, coated surface, the newest technology. This means it’s not only simpler to clean off styling product residue, etc., after each use, but you’ll find that hair glides easily over the coated surface of the curl chamber as you’re curling. The titanium ceramic-coated surface also helps smooth down flyaway and frizzes.
It evenly distributes heat so that the style you create has a salon-perfect, silky smooth, shining finish. Hair also slips right through the curl chamber after it’s curled.
The new Titanium Ceramic™ technology makes styling your hair easier and the results more professional.
Never leave your style on and unattended. However, should you fail to turn the style off, it will shut itself off automatically within 60 minutes.

USING INSTANT HEAT, THE 2 HIGH HEAT TEMPERATURE SETTINGS & UNIFORM HEAT RECOVERY SYSTEM

This styler features a high-performance heater that maintains constant temperature during use for precision styling. This Instant Heat technology has two high heat temperature settings. There is a temperature that’s gentle and safe for every type of hair, from the finest to the curliest and most resistant, and helps you create the look you want. And that’s not all. Conair’s professional salon standards of engineering provide you with a uniform and improved heat recovery system that maintains the styler at constant temperatures. There is a constant surge of power to ensure that heat is continuously and quickly delivered for optimal styling results, unlike other units, which lose heat during use.
This provides consistent styling power so that every strand of your hair is set with the same level of heat and comes out the same way for a perfect finish.
Curl Secret® 2.0 is energy efficient. The sleep mode function drops the styler’s temperature to 300°F
if styler remains idle after 20 minutes. And auto shut-off turns the Curl Secret® 2.0 off after 60 minutes.

IMPORTANT

A heat-protective glove has been supplied to help protect your hand from temporary contact with the styler.
Please note that the heat-protective glove is only designed to give initial contact protection. Discomfort will be caused by prolonged contact with the hot surface.

USER MAINTENANCE

Your styler is virtually maintenance free. No lubrication is needed. Keep all vents and openings clear of dirt and dust. If cleaning becomes necessary, disconnect the unit from the power source, allow to cool and wipe exterior with a cloth. If any abnormal condition occurs, unplug the unit, allow it to cool, and return it for repair to an authorized service representative only. No repairs should be attempted by the consumer.

CAUTION

NEVER allow the power supply cord to be pulled, twisted, or severely bent. Never wrap the cord tightly around the appliance. Damage will occur at the high flex point of entry into the appliance, causing it to rupture and short circuit. Inspect the cord frequently for damage. Stop use immediately if damage is visible or if unit stops or operates intermittently.

STORAGE

When not in use, your appliance is easy to store. Allow appliance to cool, then simply store out of reach of children in a safe, dry location. Do not jerk or strain cord at plug connections. Do not wrap the line cord around the appliance. Allow the cord to hang or lie loose and straight at the point of entry into the appliance.

WARNING: IF YOU THINK THE POWER IS OFF WHEN THE SWITCH IS OFF, YOU’RE WRONG

KEEP AWAY FROM WATER

Everyone knows that electricity and water are a dangerous combination. But did you know that an electric appliance is still electrically live even if the switch is off? If the plug is in, the power is on. So when you are not using your appliances, keep them unplugged.

ALWAYS UNPLUG SMALL APPLIANCES

LIMITED FIVE YEAR WARRANTY (U.S. AND CANADA ONLY)

Con air will repair or replace (at our option) your unit free of charge for 60 months from the date of purchase if the appliance is defective in workmanship or materials.

To obtain service under this warranty, return the defective product to the service center listed on back, together with your purchase receipt and $7.50 for postage and handling. California residents need only provide proof of purchase and should call 1-800-3-CON AIR for shipping instructions. In the absence of a purchase receipt, the warranty period shall be 60 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 60-MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY. Some
states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
IN NO EVENT SHALL CON AIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER.
Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
Please register this product at: www.conair.com/registration
SERVICE CENTER
CON AIR CORPORATION
Service Department
7475 N. Glen Harbor Blvd. Glendale, AZ 85307
©2017 CON AIR CORPORATION
Patent Pending For info on any Con air or Infinite Pro by Con air product,
call: 1-800-3-CON AIR or visit us on the web at: www.conair.com/infiniti

Scales by

Instructions for use of Weight Watchers bathroom scale
Model #WW39

Congratulations! By purchasing this Weight Watchers Scale, you’ve made the first step toward taking control of your weight. To get the greatest benefit from your purchase, please read this entire brochure before using your scale.

Before Using Scale

1. Set switch on the base of scale to measure in kg (kilograms) or lb (pounds).
2. Set scale on the floor. The surface must be level for accurate operation and safety.

Weighing In

1. Set “LB/KG” switch for either pound or kilogram readings.
2. Quickly and firmly tap the center of scale platform with the foot to activate the large digital display.
3. When “00.0” appears in the display window, step onto the scale.
   DO NOT STEP ONTO SCALE UNTIL “00.0” APPEARS IN THE WINDOW.
4. Stand on the platform without shifting or moving until weight is displayed.

NOTE: Digital display automatically turns off after several seconds.

Facts You Should Know

Your Weight Watchers®’ scale is a precise measuring instrument that is most accurate when weighing a stationary object. To ensure the most accurate readings, always try to stand on the same area of the scale platform and DO NOT MOVE.
Should the weight on the scale exceed the scale’s capacity, you may see an error message “ERR”.
Electronic sensors are sensitive. Be careful not to drop or jar the scale. Place it gently onto the floor surface, and store it where it will be protected from impact. The scale is an electronic instrument and should never be submerged in water. Clean with a damp cloth and/or glass cleaner.
In the unlikely event that the scale batteries malfunction and need to be replaced, lift the battery cover on the bottom of the scale and replace the old batteries with two new 3V Lithium batteries (CR2032). Insert both batteries with the “+” side up, one on top of the other.
Do not attempt to open the scale or remove any components. Servicing should be done by qualified technicians only.
See warranty information below.
Important Information Concerning Weight Management
Your scale is the best tool for monitoring weight. While not the only measure of weight loss, scales are the most popular method used to gauge weight-loss success. A scale measures the sum of your total body weight, which includes bone, muscle, fat, and water.
Bodyweight fluctuates during the day, and from day to day, depending on a variety of factors.

• Salt and carbohydrate intake can affect the body’s water retention.
• A large meal adds weight and can cause water retention.
• Dehydration from exercise, illness or low fluid intake can result in weight loss.
• Muscle is also a factor. Heavy-duty resistance training can build muscle, which can affect weight.
• The menstrual cycle can cause temporary weight gains and losses.

When You’re Losing Weight
It’s important not to put too much stock in the exact number on the scale, because it can and will vary. This is especially true when you’re dieting. Small weight gains and
losses are common as your body adjusts to fewer calories and more exercise.
Your scale is a valuable tool when used to track weight over a period of weeks and months. Be aware that different scales often give different results. The scale at your
doctor’s office may show one weight and your scale at home another.
So don’t get too caught up with a single number.
Don’t Overdo It!
A surefire way to get overly concerned with your weight is to weigh yourself too often.
Weigh yourself no more than once a week when you’re dieting. Though it’s hard to stick to this pattern, it’s the best way to prevent unnecessary concern with normal weight fluctuations, which are unrelated to your weight-loss efforts. Regardless of your weighing habits, it’s important that you’re consistent.
Here are 5 rules for effectively monitoring your weight – weigh yourself:

• Once a week, on the same day of the week
• At the same time of day
• In the same place
• Wearing the same clothes
• Using the same scale

To keep track of your weight, record only one number for the week. This will give you a clear picture of any trend your weight is following.
When You’re Maintaining Weight
Fluctuations in day-to-day weight tend to be smaller when weight is stable, so a more frequent weigh-in pattern is helpful.
To maintain a stable weight:

• Weigh yourself more often than once a week.
• Use the “5-pound rule” – research shows that people who keep weight within a 5-pound range are more likely to maintain healthy body weight over the long term.

While a scale can be a useful tool on your weight-loss journey, it’s not in and of itself a program for losing weight. Studies show that people lose three times more weight on Weight Watchers than they do on their own*.
Come to a meeting and learn from us the best way to lose and maintain weight.
Call 1-800-651-6000 or go to WeightWatchers.com to find a meeting near you.

LIMITED TEN YEAR WARRANTY

Conair will repair or replace, at our option, your appliance free of charge for 120 months from the date of purchase if the appliance is defective in workmanship or materials.
To obtain service under this warranty, return the defective product to the service center listed below that is nearest you, together with your sales slip and $5.00 for postage and handling. California residents need only provide proof of purchase and should call 1-800-3-CONAIR for shipping instructions. In the absence of a receipt, the warranty period shall be 120 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 120-MONTH DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Service Centers
Conair Corporation Service Department
150 Milford Road East Windsor, NJ 08520
Conair Corporation Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307
1-800-326-6247
www.conair.com

©2006 Conair Corporation. East Windsor, NJ 08520, Glendale, AZ 85307. Made in China.
©2006 Weight Watchers International Inc. All rights reserved.
Weight Watchers is the registered trademark of Weight Watchers International Inc. and is used under license.
IB-7391
06AD15147
*Heshka S et al.
Weight loss with self-help compared with a structured commercial program: a randomized trial.
JAMA 289(14): 1792, 2003.

hot clips

Instruction & Styling Guide
Model CHV26HCX

For your safety and continued enjoyment of this product, always read the instruction book carefully before using it.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING KEEP AWAY FROM WATER
DANGER – To reduce the risk of electrocution:

1. Always unplug this appliance immediately after using it.
2. Do not use it while bathing or in the shower.
3. Do not place or store appliances where they can fall or be pulled into a tub or sink.
4. Do not place in or drop into water or other liquids.
5. Do not reach for an appliance that has fallen into the water. Unplug immediately.

WARNING – To reduce the risk of burns, electrocution, fire, or injury to persons:

1. An appliance should never be left unattended when plugged in.
2. Do not pull, twist or wrap line cord around the appliance.
3. Close supervision is necessary when this appliance is used by, on, or near children or individuals with certain disabilities.
4. Use this appliance only for its intended use as described in the manual. Do not use attachments not recommended by Conair.
5. Never operate this appliance if it has a damaged cord or plug if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to an authorized service center for examination and repair.
6. Keep the cord away from heated surfaces.
7. Never block the air openings of the appliance or place them on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.
8. Never use while sleeping.
9. Never drop or insert any object into any opening or hose.
10. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
11. Do not use an extension cord with this appliance.
12. Do not touch metal “radiator” strips that hold rollers, as they will be hot.
13. Do not touch the metal rails that heat the clips.

SAVE THESE INSTRUCTIONS

OPERATING INSTRUCTIONS

How to operate your hairsetter with heated clips:

1. Place hairsetter on a firm, flat surface. With the lid closed, plug the cord into the outlet. This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
2. Once plugged in, the red light will go on and the rollers will heat up quickly.
   Rollers are ready to use when the ready dot on the roller turns transparent white. (Please refer to HOW TO CURL YOUR HAIR for further instruction.)
3. Allow rollers and clips to heat with the lid closed, as this will provide the fastest, most efficient heat-up. Once the rollers reach your desired temperature, you can begin setting your hair.
4. Hair should be clean and dry or slightly damp – never wet – when setting. For tighter curls, allow rollers to heat longer at a higher temperature.
5. Never leave your hairsetter on and unattended. Always unplug the hairsetter when not in use. Allow the hairsetter to cool down after use, and store in a safe place.

USER MAINTENANCE

Your hairsetter is designed for household use and is virtually maintenance-free. This product represents the highest standards of workmanship and engineering research. If cleaning becomes necessary, disconnect the appliance from the power source. Allow the setter to cool. Clean the unit and the heating rails with a cloth. (Occasionally you may want to clean your rollers. Use a damp cloth and mild detergent or soap.) If any abnormal condition occurs, unplug the hairsetter, allow it to cool, and return it to an authorized service representative for repair.
STORAGE
Allow hairsetter to cool. Handle cord carefully to prolong its life; avoid jerking or straining at plug connections. Store hairsetter out of reach of children in a safe, dry location.

HOW TO CURL YOUR HAIR

1. Place ends of the hair on roller and wind toward the scalp. Roll up hair firmly remove the clip from the heated rail and secure over the roller. Place another clip on an aluminum rail for heat-up. Continue to add clips to the heating rail as rollers are added to the hair.
   
2. The firmness of the curl is regulated by the diameter of the roller and the length of time the roller is left in your hair.
   
3. For tight, firm curls, use smaller rollers and leave them in the hair for at least ten minutes before removing them. For soft, wavy curls, use larger rollers and remove rollers after a shorter period of time.
   
4. Removing roller: Hold roller in one hand while removing heated clip with the other. Gently drop roller (DO NOT PULL) and let curl bounce back after roller has been completely removed. Let cool for one minute for a firmly set curl, and then style your hair into a look that lasts for hours.

IMPORTANT: After using the hairsetter several times, you will find the best roller selection and the best timing for the texture of your hair and for the result you desire.

MEDIUM ROLLERS
Use on short hair to create a fullness and tight curl. Tight curls can be used at the nape of the neck and to frame your face.

LARGE ROLLERS
Use medium to long hair to create a looser curl that’s bouncy and full of body.

JUMBO ROLLERS
Use medium to long hair to create the smooth sleek lines of softer, sophisticated hairstyles.

TO ORDER ExTRA ROLLERS

Rollers come packed three of the same size to a carton. Rollers are sold by carton only.

Please add postage and handling to all orders.
Postage and handling are as follows: Orders up to $5.00: add $.50 to order. Orders from $5.01 to $10.00: add $1.00 to order. Orders of $10.01 and over: add $1.50 to order.
MAIL ORDER TO:
Conair Corporation
150 Milford Road, East Windsor, NJ 08520
Service Department
7475 North Glen Harbor,
Glendale, AZ 85307
Include return name and address and model number of replacement rollers. Please make the check payable to Conair Corporation.
WARNING:
IF YOU THINK THE POWER IS OFF WHEN THE SWITCH IS OFF, YOU’RE WRONG.

KEEP AWAY FROM WATER

Everyone knows that electricity and water are a dangerous combination. But did you know that an electrical appliance is still electrically live even if the switch is off? If the plug is in, the power is on. So when you are not using your appliances, keep them unplugged.
ALWAYS UNPLUG SMALL APPLIANCES

LIMITED ONE-YEAR WARRANTY

Conair will repair or replace (at our option) your unit free of charge for 12 months from the date of purchase if the appliance is defective in workmanship or materials.
To obtain service under this warranty, return the defective product to the service center listed on the back, together with your purchase receipt and $5.00 for postage and handling. California residents need only provide proof of purchase and should call 1-800-366-0937 for shipping instructions. In the absence of a purchase receipt, the warranty period shall be 12 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED  WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 12-MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, ExPRESS OR IMPLIED, WHATSOEVER.
Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply to you. This
the warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
Please register this product at:
www.conair.com/registration
Service Center
Conair Corporation
Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307

©2012 Conair Corporation
150 Milford Road, East Windsor, NJ 08520
7475 N. Glen Harbor Blvd., Glendale, AZ 85307
IB-11476
12PH132584

CONAIR ThermaLuxe™ Massaging Heating Pad

IMPORTANT SAFETY INSTRUCTIONS

DANGER – To reduce the risk of burns, electric shock and fire, this product must be used in accordance with the following instructions:

1. Read all instructions.
2. ALWAYS UNPLUG THE UNIT FROM THE ELECTRICAL OUTLET IMMEDIATELY AFTER USING.
3. Do not use while sleeping. Avoid falling asleep while using the product.
4. Do not use on an infant or an animal.
5. This pad is not to be used on or by any individual with certain disabilities, sleeping or unconscious person, or a person with poor blood circulation unless carefully attended.
6. Do not use on areas of insensitive skin.
7. Burns can occur regardless of control setting; check skin under pad frequently.
8. Never use pad without removable cover in place.
9. Do not use where oxygen is being administered.
10. Do not use pins or other metallic means to fasten this pad in place.
11. Do not sit on or crush pad – avoid sharp folds.
12. Never pull this pad by the line cord.
13. Do not use the cord as a handle.
14. Carefully examine inner cover and line cord before each use. Discard the pad if inner covering or line cord shows any sign of deterioration.
15. Do not tamper with this pad in any way. There are no user-serviceable parts. If, for any reason, this pad does not function satisfactorily, return it to authorized service center at address given.
16. Do not use this pad with liniment, salve or ointment preparations that contain heat-producing ingredients, as skin burns could result. Use wherever hot applications are desirable for personal comfort, and wherever recommended by your physician or dentist for the relief of pain.
17. Loop cord loosely when storing; tight wrapping may damage cord and internal parts.
18. Keep the pad away from heated surfaces.
19. Place pad on top and not under the part of the body needing heat.
20. Do not put this pad in the microwave.
21. Do not leave pad unattended, especially if children are present.
22. Do not use pad underneath bedcovers and other types of blankets.
    Do not place covers, such as sheets and blankets, above pad. Only the cloth cover provided with the pad should be used.
23. Do not use pad on sensitive skin or when taking medication that can cause sensitive skin.
24. Do not exceed 30 minutes of treatment at one time.

SAVE THESE INSTRUCTIONS

Cautions:

• This product does not have an automatic heat-off feature. Slide switch to OFF when done.
• This heating pad should not be used in the following cases unless directed by a physician: if you have diabetes, tuberculosis, benign or malignant tumors, phlebitis and thrombosis, hemorrhages, inflammations of the skin, undetermined calf pain or joint pain, or if you have poor circulation. Consult a physician before using if you have any kind of fungal infection, swelling, fracture or persistent pain.
• Consult your physician should you have any questions regarding the therapeutic use of this heating pad.
• Do not use on any unexplained pain, swollen muscles, or following a serious muscular injury before consulting your physician.
• Keep away from children.
• Discontinue use of product if pain increases or swelling occurs after application.
• Do not use while bathing or showering. Use only in a dry environment.
• Consult your doctor before using in cases of illness or medical condition, including but not limited to pacemaker use, pregnancy or cancer.
• If you experience pain in a muscle or joint for a prolonged period of time, discontinue use and consult your doctor. Persistent pain could be a symptom of a more serious condition.
• Never use any heating products on open wounds, discolored areas, or any area of the body that is swollen, burned, bruised, inflamed or where skin eruptions, ulcerated sores or varicose veins are present.
• This product should never be used by any individual suffering from any ailments that would limit or altogether inhibit the user’s capacity to feel or have any sensation in the body part that this product is being used for.
• Use of this product should be pleasant and comfortable. Should pain or discomfort result, discontinue use and consult your physician.
• Ensure that your hands are dry when operating the controls or removing the plug.
• Do not fall asleep while using this massager.
• For indoor use only.
• DO NOT EXCEED 30 MINUTES OF TREATMENT AT ONE TIME.

OPERATING INSTRUCTIONS

To operate the Therma Luxe Massaging Heating Pad, first plug the power jack into the hand control and plug the cord into a standard 120V electrical outlet. Turn on the switch for heat. Set the slide switch to choose between LO and HI levels for vibration. For maximum benefit, use should not exceed 30 minutes at one time.

Timer Feature

The massage motors will automatically shut off after approximately 20 minutes. To restart, first set the massage switch back to OFF and then set the switch to LO or HI again. Please note the heating function operates independently of the timer.

LIMITED FIVE-YEAR WARRANTY (U.S AND CANADA ONLY)

Conair will repair or replace (at our option) your unit free of charge for 60 months from the date of purchase if the appliance is defective in workmanship or materials.
To obtain service under this warranty, return the defective product to the service center listed on back, together with your purchase receipt and $3.00 for postage and handling. California residents need only provide proof of purchase and should call 1-800-3-CONAIR for shipping instructions. In the absence of a purchase receipt, the warranty period shall be 60 months from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 60-MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

Please register this product at www.conair.com/registration
Service Center
Visit us on the web at www.conair.com
©2018 Conair Corporation
East Windsor, NJ 08520 / Glendale, AZ 85307

Model GS28/GS28L

REMOVES
WRINKLES & ODORS
FROM GARMENTS & KILLS DUST MITES!

Instructions for Use

For your safety and continued enjoyment of this product, always read the instruction book carefully before using.

IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially when children are present, basic safety precautions should always be taken, including the following:
READ ALL INSTRUCTIONS
BEFORE USING
DANGER – Any appliance is electrically live even when the switch is off. To reduce the risk of death by electric shock:

1. Always unplug the appliance immediately after using.
2. Do not place or store appliances where it can fall or be pulled into a tub or sink.
3. Do not place in, or drop into water or other liquids.
4. If an appliance falls into water, unplug it immediately. Do not reach into the water. 

WARNING – To reduce the risk of burns, electrocution, fire, or injury to persons:

1. This appliance should never be left unattended when plugged in.
2. This appliance should not be used by, on, or near children or individuals with certain disabilities. Unsupervised use could result in fire or personal injury.
3. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
4. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been dropped or damaged, or dropped into water. Do not attempt to repair the appliance. Incorrect reassembly or repair could cause a risk of fire, electric shock, or injury to persons when the appliance is used. Return the appliance to an authorized service center for examination and repair. 
5. Keep the cord away from heated surfaces. Do not allow the cord to contact heated surfaces. Do not pull or twist the cord. Let the appliance cool completely before putting it away.
6. This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not, contact a qualified electrician. Do not attempt to defeat this safety feature.
7. Never drop or insert any object into any opening or hose.
8. Do not use utdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
9. Do not use an extension cord to operate the appliance.
10. The surfaces of this appliance may be hot when in use. Do not let heated surfaces touch eyes or skin.
11. Do not place the steam nozzle directly on any surface or on the appliance power cord while it is hot or plugged in. Use the stand provided.
12. Unplug this appliance before filling or emptying. Do not  verfill.
13. While emitting steam, this appliance may cause burns if it is used too close to the skin, scalp or eyes, or if it is used incorrectly. To reduce the risk of contact with hot water discharging from steam vents, test the appliance before each use by holding it away from body.
14. Do not operate the steamer without properly filling the water tank.
15. Always keep the hose and nozzle elevated above the water tank.
16. Never yank cord to disconnect from outlet. Instead, grasp the plug and pull to disconnect.
17. Burns could occur from touching hot metal parts, hot water, or steam. Use care when removing the water tank or when you turn a team appliance upside down – there may be hot water in the reservoir.
18. To reduce the likelihood of circuit overload, do not operate another high-wattage appliance on the same circuit.
19. If an extension cord is absolutely necessary, a 15 ampere rated cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over.
20. Always remove the water tank from the appliance before filling t with water.
21. When changing attachments, please be sure the unit is off and no steam is being released in order to avoid contact with hot water.
22. Use caution when changing attachments, as they may contain hot water from condensation. Ensure the attachments are dry or cooled off, to avoid contact with hot water.

SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY

UNPACKING INSTRUCTIONS

Place the box on a large, sturdy flat surface. Carefully remove the appliance from the packing material. Keep all plastic bags away from children.
STEAMER

ASSEMBLY

STEP 1 – Attaching the Telescopic  Pole and Rotating Hanger
Insert the bottom of the larger metal telescopic pole into the holder on the unit base and screw the set screw until tight. (Caution: Do not over-tighten.)
Then attach pieces as shown in Fig. 1.

STEP 2 – Attaching the Steamer Hose
Be sure the unit is off. Insert the angled end of the hose into steamer housing and twist clockwise to securely lock the hose onto the housing. (Be sure both connections at ends of hose are correct before operating appliance.)
Extend the telescopic pole and hang the steam nozzle from the rotating handle. The hose may be stiff upon removal from the box.
Hose will relax after initial use. The handle will sit properly on pole support once the hose is relaxed. (Fig. 4)
TURNING THE STEAMER ON
The steamer has three settings:

The pause feature allows you to stop the unit from steam if you need to step away from the unit for a while, without actually turning the steamer off.
USING ROTATING HANGER
This unit comes with a rotating hanger. To use the hanger, simply place it on top of the pole firmly (Fig. 1). It is now in place to rotate 360˚. Hang your garment and steam away wrinkles. Turn as you wish.

USING PANT CLIP SYSTEM
This fabric steamer is equipped with a pant clip system for holding pants taut for faster and more effective steaming. The bottom clips can be adjusted by loosening the knob (on the telescopic pole) and moving the pole up and down, depending upon the length of the pants (see Fig. 2). Clip pants as shown in Fig. 3 and steam. Please note some pants may be too long to use the bottom clips. If that is the case, just simply use the top clips and let your pants hang freely.

OPERATING INSTRUCTIONS

BEFORE FILLING THE WATER TANK
Turn the water tank upside down and inspect to make sure the valve and spring assembly are functioning. Place the tank in the reservoir and check that it is seated
securely. If the tank has been stored with water inside, it may be necessary to remove the water and clean the tank. Follow the steps for care and cleaning.
FILLING THE WATER TANK
(PRIOR TO PLUGGING IN THE APPLIANCE)
Remove the water tank with the handle and turn it upside down. Unscrew the valve in the center of the base. Fill the tank by holding it under a source of running cold water until it is filled to the desired level. Do not overfill. Screw the valve cap onto the water tank and return the tank to the upright position. Place the water tank onto the base and make certain it is seated properly in the reservoir. DO NOT FILL THE TANK WITH HOT WATER.

OPERATING THE STEAMER

1. Make sure the ON/OFF switch is in the OFF position.
2. Make sure all hose connections are secure and tight.
3.  Make sure the telescopic pole is fully extended and the hose is not twisted or kinked.
4. Plug the steamer cord into a normal electrical outlet.
5.  Turn the ON/OFF switch to the ON position.
6.  The switch will light to indicate when power is on.
7.  Steam will be produced from the nozzle in about one minute.
8. To turn the steamer off, turn the ON/OFF switch to the OFF position.

GETTING TO KNOW

CLEANING AND STORING

1. Turn the ON/OFF switch to the OFF position and unplug from the power source.
2. Wait for the steamer to cool completely for at least 30 minutes.
3.  Unplug the power cord and retract it into the housing.
4. Remove the steamer hose.
5.  Remove the water tank from the unit, unscrew the valve, and empty unused contents. Allow airing to dry.
6. Remove excess water from the reservoir by unscrewing the plug on the bottom of the steamer and letting the water drain out.
7.  Collapse telescopic hanger rod.
8.  Replace the water tank.
9. Store the unit.

CAUTION: Hose will be hot when in use. Avoid prolonged contact.

OTHER IMPORTANT NOTES

During operation, the steamer hose may gurgle. This is a normal result of condensation collecting inside the hose. Simply lift the handle upward until the hose is
extended to its full height. The gurgling will disappear when the excess moisture inside the hose has had a chance to drain back  into the base.

DECALCIFICATION

If the appliance begins to produce steam more slowly than usual or stops producing steam and then starts again, you may need to decalcify your steamer. Decalcification refers to removing the calcium deposits that form overtime on the metal parts of the steamer. For best performance from the Conair ® Ultimate Fabric Steamer, decalcify the unit from time to time. The frequency depends upon the hardness of your tap water and how often you use the steamer.
To decalcify, use a solution of 1/3 white vinegar and 2/3 water in the water tank. Replace the water tank in the unit. Plug the unit into an electrical outlet. Turn to the
ON position and run until half the amount has steamed (1 liter). Turn the unit to the OFF position, unplug from the electrical outlet, and allow to sit for 30 minutes. Remove the water tank.
Remove excess water from the reservoir by unscrewing the plug at the bottom of the steamer and holding it over the sink, allowing the water to drain from the
internal reservoir.
Repeat the above procedure as many times as necessary until a normal steam rate returns, usually 2–3 times. With each repeated cycle, use a fresh solution of vinegar and water. Run one cycle of fresh, cold water through the unit at the completion of decalcification before using the unit again to steam garments.

HOW TO STEAM

Grasp the handle of the steam nozzle with the steam jets facing away from you. Begin at the bottom of the fabric to allow the steam to rise inside and outside, removing wrinkles. Slowly move the nozzle from the bottom to the top of the fabric. Remove the nozzle from the garment and smooth the fabric with your free hand. Some fabrics are best steamed on the underside of the material. This will allow the fibers of the fabric to relax, eliminating wrinkles.
NOTE: Test fabric for colorfastness in an inconspicuous spot. Drape linens, towels, handkerchiefs, and napkins over a rod or place on a towel rack.
Heavier fabrics may require repeated steaming. Repeat as necessary.
With practice, you will gain speed and efficiency. You will soon learn which fabrics require multiple steam applications.
Do not directly touch velvet or silk with the steam head.

Always steam with the hose in an upright position, so any condensation is free to flow back into the steamer.
If you steam in a low position, condensation will collect inside the hose. This will cause gurgling and some water droplets to form near the steam jets on the handle. To avoid this, frequently lift the steam handle upward until the hose is extended to its full height.
TO STEAM DRAPES
Wash and dry drapes as directed, according
to fabric type. Rehang drapes and steam
when they are in place.

TROUBLESHOOTING THE STEAMER

• PROBLEM – Steamer fails to heat
  CAUSE – Steamer not plugged in
  SOLUTION – Plug into an electrical outlet
• PROBLEM – No steam
  CAUSE – The water level is low
  SOLUTION – Turn ON/OFF switch off and refill the water tank
• PROBLEM – Water drips from the nozzle
  CAUSE – Condensation in hose
  SOLUTION – Hold the hose vertically and allow water to drain back into the unit
•  PROBLEM – Nozzle gurgles
  CAUSE – Condensation in hose
  SOLUTION – Hold the hose vertically and allow water to drain back into the unit
•  PROBLEM – Poor steam performance
  CAUSE – Sediment in tank
  SOLUTION – Decalcify reservoir and water tank

NOTE: Amounts of chemicals in the water will vary in different areas. To ensure continued operation of the steamer, never store without cleaning and removing excess water from the reservoir and water tank.

LIMITED ONE-YEAR WARRANTY

Conair will repair or replace (at our option) your unit free of charge for 12 months from the date of purchase if the appliance is defective in workmanship or materials. To obtain service under this warranty, return the defective product to the service center listed, together with your purchase receipt and $3.00 for postage and handling. California residents need only provide proof of purchase and should call 1-800-366-0937 for shipping instructions. In the absence of a purchase receipt, the warranty period shall be 12 months from the date of manufacture.

ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 12-MONTH DURATION OF THIS WRITTEN,
LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH 
OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. 
Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

Please register this product at: www.conair.com/registration

Service Center

Conair Corporation
Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307
For information on any Conair product call: 1-800-3-CONAIR or visit us on the web at www.conair.com
©2010 Conair Corporation
East Windsor, NJ 08520/Glendale, AZ 85307
10PA115080
IB-10126

All GS38 Models

Instruction Booklet
For your safety and continued enjoyment of this product, always read the instruction book carefully before using it.

GETTING TO KNOW YOUR STEAMER

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially when children are present, basic safety precautions should always be taken, including the following:

READ ALL INSTRUCTIONS BEFORE USING

DANGER – Any appliance is electrically live even when the switch is off. To reduce the risk of death by electric shock:

1. Always unplug appliances immediately after use and before cleaning.
2. Do not place or store appliances where they can fall or be pulled into a tub or sink.
3. Do not place in, or drop into water or other liquids.
4. Do not reach for an appliance that has fallen into the water. Unplug immediately. 
5. Use only in a dry area.

WARNING – To reduce the risk of burns, electrocution, fire, or injury to persons:

1. This appliance should never be left unattended when plugged in.
2. This appliance is not a toy and is not to be used by children.
3. Close supervision is necessary when this appliance is used near children or individuals with certain disabilities. Unsupervised use could result in fire or personal injury.
4. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
5. Rest the appliance on a stable surface when placed on its base.
6. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been dropped or damaged, or dropped into water. Do not attempt to repair the appliance. Incorrect reassembly or repair could cause a risk of fire, electric shock, or injury to persons when the appliance is used. Return the appliance to an authorized service center for examination and repair.
7. Do not allow the cord to contact heated surfaces. Do not pull or twist the cord. Let the appliance cool completely before putting it away. Loop cord loosely around the appliance when storing.
8. This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
9. Never drop or insert any object into any opening.
10. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
11. Do not use an extension cord to operate the appliance.
12. The surfaces of this appliance are hot when in use. Do not let heated surfaces touch eyes or skin.
13. Do not place the steam nozzle directly on any surface or on the appliance power cord while it is hot or plugged in.
14. Unplug this appliance before filling or emptying the water.
15. Do not operate the steamer without properly filling the water container with distilled water.
16. Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect.
17. Burns could occur from touching hot parts, hot water, or steam. Use care when removing the water reservoir or when you turn a steam appliance upside down – there may
    be hot water in the reservoir. Always position steamer with head away from you and any other person when turning on.
18. Do not hold hand in front of steam.
19. To reduce the likelihood of circuit overload, do not operate another high-wattage appliance on the same circuit.
20. Use caution when installing or removing an attachment as it may contain hot water from condensation. Ensure that the unit is off, attachment is dry or cooled off to avoid
    contact with hot water.
21. Never steam clothes you, or someone else is wearing.
22. When emitting steam, this appliance may cause burns if it is used too close to the skin or eyes, or if it is used incorrectly. To reduce the risk of contact with hot water emitting from the steam vents, test the appliance before use by holding it away from the body.

SAVE THESE INSTRUCTIONS

IMPORTANT

FOR HOUSEHOLD USE ONLY

FILLING INSTRUCTIONS

1. Make sure the unit is unplugged.
2. Stand the unit on a table and grasp with one hand.
3. On other hand, move the release switch up toward the steam head nozzle.
4. Pull the reservoir out, away from the steamer body.
5. The rubber inlet cover is located on the top of the water reservoir.
6. Open the inlet cover and fill the reservoir with distilled water (which can be found in grocery stores). We recommend that you use distilled water only as this will prevent
   mineral deposits in the boiler that can reduce the performance or clog the water system.
7. Close the inlet cover and return the reservoir to its place, making sure that it snaps in place and is secure.

OPERATING INSTRUCTIONS

1. Fill the water reservoir with distilled water. We recommend that you use distilled water only, as this will prevent mineral deposits in the boiler that can reduce performance or clog the water system.
2. Plug the unit into the electrical outlet.
3. The blue READY light will illuminate and begin blinking. Allow 40 seconds for the unit to warm up. The appliance is ready to use when the READY light stops blinking and remains solid. Note: Before the first use or when the unit has not been used for a long period of time, it will be necessary to prime (i.e., fill with water) the internal tank while the steamer prepares to steam. You may hear a small tapping noise during the heat-up process; this is normal.
4. Your steamer has 2 options for steam, regular Steam, and Turbo. Use the Steam setting (blue button) for delicate fabrics or freshening lightly wrinkled garments. Use the Turbo setting (red button) for thicker fabrics and heavily wrinkled articles.
   
5. Pointing the steam jets away from you, and anyone else in the room, press either the blue Steam button or the red Turbo button to release steam. Always have steam facing away from you or anyone in the room. 
6. When first using the device, test on an old cloth, as there may be sediment left from the manufacturing process or transportation.
7. To stop the flow of steam, depress the button(s) that you have turned on, either the red, blue, or both.
8. Unplug the device when it is not in use.

USING CREASER

This garment steamer has a built-in creaser on the top of the unit. To use, slide the garment under the clip and align the edge with the pattern as marked on the creaser. Press the Steam button and steam will issue from the port on the top of the unit. Slide the steamer along the edge of the garment to create a sharp crease.

Note: Steam will continue to emit from the steam slot on the front of the unit during creaser use!

USING 3-IN-1 ATTACHMENT

With the garment steamer off and cool, snap the silicone brush attachment over the steam head ensuring it is firmly affixed. At this point, the silicone brush can be used or you can choose to affix either the Bristle Brush or Delicate Fabric Guide inserts into the channel on the top of the silicone Brush attachment as desired. Note, only one function of the 3-In-1 attachment can be used at a time

CAUTION: Use extreme care when changing the attachments after the unit has been in use as the steam head will continue to be hot.

STEAMING TIPS

1. First test unit on an inconspicuous area of the item to be steamed using the regular Steam setting to ensure fabric can tolerate the effects of steam. If there is no evidence of damage, you can proceed to use the steamer on that item.
2. To prepare your fabric for steaming, brush it with the brush attachment. This will loosen the fibers and allow better steam penetration.
3. Hang your garment or fabric. Note: Avoid using metal clothes hangers, if possible.
4. Pass the steam jets just above the fabric where the wrinkles are. It may take a few passes to remove the wrinkles completely.
5. For heavier fabrics or severely wrinkled fabrics, you may position the steamer head directly on the fabric for a few seconds to remove wrinkles. Be cautious when working
   with delicate fabrics.
6. After use, turn the unit off by depressing the button(s) that you have turned on, either the red, blue, or both. Empty any remaining water from the tank to avoid leakage. With dry hands, unplug your garment steamer from the outlet.
   BE SURE TO PRESS THE BUTTONS “OFF” PRIOR TO UNPLUGGING THE UNIT. 
7. CAUTION: If hanging a garment on a door while steaming, be careful not to damage the door with steam.
8. When steaming, always keep the unit in motion. Do not continuously hold steamer over an area or touch steamer jets directly to fabric for more than a few seconds as this can cause damage, including shrinkage, melting, or color shift on certain types of material.
9. In the case of heavier, durable fabrics such as wool coats or bedding, the Turbo setting and slower passes with the steamer may be necessary to achieve desired results. As always, start by testing on an inconspicuous area of the item to be steamed using the regular Steam setting to ensure fabric can tolerate the effects of steam, and adjust your technique as needed to obtain the results desired.

LIMITED ONE-YEAR WARRANTY (U.S. AND CANADA ONLY)

Conair will repair or replace (at our option) your unit free of charge for 12 months from the date of purchase if the appliance is defective in workmanship or materials.

To obtain service under this warranty, return the defective product to either service center listed below, together with your purchase receipt and $12.00 for postage and handling.

California residents need only provide proof of purchase and should call 1-800-3-CONAIR for shipping instructions. In the absence of a purchase receipt, the warranty period shall be 12 months from the date of manufacture.

ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE SHALL BE LIMITED IN DURATION TO THE 12-MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY. Some
states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY
OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

Service Centers

For information on any Conair product, call
1-800-3-CONAIR or visit us on the web at
www.conair.com

Please register this product at:
www.conair.com/registration

©2016 Conair Corporation
East Windsor, NJ 08520
Glendale, AZ 85307
Made in China
15PA016551
IB-13950

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be taken, including the following:

READ ALL INSTRUCTIONS BEFORE USING

DANGER – To reduce the risk of electric shock:

1. Always unplug this appliance from the electrical outlet immediately after using and before cleaning.
2. Do not reach for an appliance that has fallen into water. Unplug immediately.
3. Do not use while bathing or in a shower. Use only in a dry area.
4. Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place or drop into water or other liquids.

WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

1. An appliance should never be left unattended when plugged in. unplug from outlet when not in use, and before putting on or taking off parts.
2. This massager is not a toy!
3. Consult your doctor before using in case of pregnancy, illness, medical condition, or persistent pain.
4. Do not use on any unexplained pain or swollen muscles, or following a serious injury, before consulting your physician.
5. Do not use massager in close proximity to loose clothing or jewelry.
6. Keep long hair away from massager while in use.
7. Do not operate under a blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.
8. This appliance should not be used by, on, or near children or individuals with certain disabilities.
9. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by Conair.
10. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.
11. Do not carry this appliance by the power supply cord or use the cord as a handle.
12. Keep the cord away from heated surfaces.
13. Never operate on a soft surface, such as a bed or couch, where air openings may be blocked.
    • 3 Attachments
      1. Dual Node Massage
      2. Pinpoint Massage
      3. Single Node MassageKeep the air openings free of lint, hair, and other particles
14. Never drop or insert any object into the product.
15. Do not use outdoors.
16. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
17. Ensure that your hands are dry when operating the controls or removing the plug.
18. To disconnect, turn all controls to the OFF position, then remove plug from outlet.
19. This appliance is for household use only.
20. Do not stand on or in the foot bath. Use only while seated. Place feet in bath and remove feet from bath while in a seated position only.
21. Never use while sleeping or drowsy.
22. Keep out of the reach of children.
23. Use heated surface carefully. May cause serious burns. Do not use on sensitive skin or in the presence of poor circulation. The unattended use of heat by children or incapacitated persons may be dangerous.
24. Burns may result from improper use.
25. To prevent scalding, never add boiling or steaming water to the foot bath.
26. Temperatures sufficiently high to cause burns may occur regardless of the control setting. Do not use on an infant, individuals with certain disabilities, or on a sleeping or unconscious person. Check the skin in contact with the heated area of the appliance frequently to reduce the risk of injury.
    
    This unit has a two-wire, double-insulated polarized plug

OPERATING INSTRUCTIONS

To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If is still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way

CAUTION

1. Consult your doctor before using in case of illness or medical condition, including but not
   limited to pacemaker use, pregnancy, cancer, infection, fracture, or persistent pain.
2. Do not use if you have any of the following conditions: diabetes, tuberculosis, benign or malignant tumors, phlebitis or thrombosis, hemorrhages, open or fresh wounds, ulcerated sores, varicose veins, poor circulation or bruised, discolored, burned, broken, swollen, or inflamed skin or heat sensitivity.
3. This product should not be used by any individual suffering from a condition that limits or altogether inhibits the user’s capacity to feel or have sensation in any part of the body.
4. If you experience pain in a muscle or joint for a prolonged period of time, discontinue use and consult your doctor. Persistent pain could be a symptom of a more serious condition.
5. Use of this product should be pleasant and comfortable. Should pain or discomfort result, discontinue use and consult your physician.
6. If the user empties water contrary to instructions, a small amount of water may issue from the drain hole. This is normal, as it is a safety measure to prevent water ingress. Wipe floor with dry cloth after use to avoid damage.
   

USER/MAINTENANCE INSTRUCTIONS

1. Make sure foot bath is unplugged and is in the OFF position.
2. When transporting foot bath, position hands on opposite sides of foot bath for most secure grip.
3. Place foot bath on floor, fill foot bath with warm or cold water, and plug into wall outlet. Never plug in or unplug the foot bath while your feet are in water.
4. The heat setting is designed to maintain the temperature of warm water, not to heat water.
5. Sit in a chair and place your feet in the water. Never stand in foot bath.
6. Select foot bath feature by pushing ON/OFF button for bubbles and heat.
7. Choose one of the 3 attachments and place on post at the top of the foot bath. Select massaging by pushing ON/OFF for massaging. Place foot on attachment and apply pressure.
   Move your foot around for more pressure and treatment.
8. To clean the unit, make sure the massager is unplugged. Allow the unit to cool, and then wipe down with a damp cloth using soap and water only. Do not use strong chemical cleaners.
9. Fill foot bath with warm or cold water to the level indicator MAX. Do not fill above water-level indicator. Never overfill.
10. Pour water out of the foot bath from the side opposite the line cord only.
11. Do not hang unit from power cord.
12. Store unit in its box or in a clean, dry place. Wrap power cord loosely around tub feet.

SAVE THESE INSTRUCTIONS
SERVICING OF DOUBLE-INSULATED PRODUCTS
In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated product, nor should a means for grounding be added to the product. Servicing a double-insulated product requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated product must be identical to the parts they replace. A double insulated product is marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED.” This symbol (square within a square) may also be marked on the product.

FEATURES

1. 2 push buttons to control bubbles/heat and massage
2. full platform generates aerating bubbles
   
   • attachments
     
     1. dual node
     2. single node
     3. pinpoint
3. translucent splash cover
4. nonslip feet
5. line cord wrap

RECOMMENDED MASSAGING TIMES

Generally, massage should not last longer than 10 to 15 minutes. Treatment may be applied once or twice daily as desired. Allow unit to cool before using again. As a person’s metabolism varies, so does his or her response to massage. You will soon adjust your massage time to suit your needs and personal comfort. If you have any concerns regarding use, we recommend you consult your physician.

LIMITED ONE YEAR WARRANTY (U.S. AND CANADA ONLY)

Conair will repair or replace (at our option) your unit free of charge for 12 months from the date of purchase if the appliance is defective in workmanship or materials.
To obtain service under this warranty, return the defective product to the service center listed below, together with your purchase receipt and $12.00 for postage and handling. California residents need only provide proof of purchase and should call 1-800-3-CONAIR for shipping instructions.
In the absence of a purchase receipt, the warranty period will be 12 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 12-MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental or consequential damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

Service Center
Conair Corporation
Service Department
7475 North Glen Harbor Blvd.
Glendale, AZ 85307
Please register this product at: www.conair.com/registration

Visit us on the web at: www.conair.com
©2016 Conair Corporation
East Windsor, NJ 08520/Glendale, AZ 85307
IB-10298A
FB30
16PS016875

Product Overview

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING
KEEP AWAY FROM WATER

DANGER — any appliance is electrically live, even when the switch is off. To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water. Unplug immediately.
2. Do not use while bathing or in the shower.
3. Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquids.
4. Always unplug this appliance from the electrical outlet immediately after using. 5. Unplug this appliance before cleaning.

DO NOT REACH INTO THE WATER

WARNING– To reduce the risk of burns, electric shock, fire, or injury to persons:

1. This appliance should never be left unattended when plugged in.
2. This appliance should not be used by, on, or near children or by individuals with certain disabilities.
3. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
4. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped, damaged, or dropped into water. Return the appliance to an Authorized Service Center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Never operate the appliance with the air opening blocked or while on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair and the like.
7. Never drop or insert any object into any opening.
8. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
9. To disconnect, turn all controls to OFF, then remove plug from outlet.
10. Do not place appliance on any surface while it is operating.
11. Do not use this appliance with a damaged or broken comb or with teeth missing from the blades, as injury may occur.
12. Avoid skin contact with moving blades.
13. If the cord becomes tangled during use, turn the unit off and straighten cord before operating again.

OPERATING INSTRUCTIONS

This appliance is used on Alternating Current 120V (AC 60 hertz) only.

To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in the outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

Your new Conair® haircut kit has everything you need to achieve professional haircuts at home. It features a powerful clipper with cutting precision. Also included are 8 numbercoded comb attachments for different hair lengths (including left and right ear combs). It also comes with 2 styling clips to assist you in cutting longer hair styles, a storage case, barber comb, barber scissors, barber cape, cleaning brush, lubricating oil and a blade guard for easy maintenance of the clipper blades.

THE CONAIR GUIDE TO CUTTING HAIR AT HOME

Before you start:

1. Inspect your clipper. Make sure it’s free of hair and dirt, properly oiled, and running smoothly.
2. Place a towel or cape around the neck of the person whose hair is being cut.
3. Seat the person so that his or her head is at your eye level. This gives you greater visibility and control.
4. First, comb hair until it’s tangle-free. Then hold clipper in a comfortable grip. Now you’re ready to cut.
   Please note your [number] cut™ 20-piece haircut kit comes with easy-to-use number-coded combs, so you can easily remember your favorite comb once you start to use the kit on a regular basis.

MEDIUM TO LONG CUT

To begin with, cut only a small amount of hair until you become used to the length each attachment leaves the hair. Try the longest attachment on the clipper first. If you want a shorter cut, you can then use shorter combs.

• Short attachment comb (number 1) cuts hair to 1/8″.
• Medium-Short attachment comb (number 2) cuts hair to 1/4″.
• Medium-Long attachment comb (number 3) cuts hair to 3/8″.
• Long attachment comb (number 4) cuts hair to 1/2″.
• Long attachment comb (number 5) cuts hair to 5/8″.
• Long attachment comb (number 6) cuts hair to 3/4″.
• Long attachment comb (number 7) cuts hair to 7/8″.
• Long attachment comb (number 8) cuts hair to 1″.
• Left ear attachment comb lightly tapers over left ear.
• Right ear attachment comb lightly tapers over right ear.

Attach combs by holding them teeth up, then snapping onto the bottom of the clipper blade.

To remove comb attachments, place index finger and thumb as illustrated; then pull out and up.

NOTE: Never push or shove the clipper through the hair to make it move more quickly. Professional experience shows that the clipper works most efficiently when it cuts through the hair at its own speed.

To begin cutting hair:

1. The hair should be combed in its natural direction.
   
2. Using the largest attachment comb, trim sides from the bottom upwards. Hold clipper lightly against the hair with teeth of the attachment comb pointing upward, yet flat against the head. Gradually lift the clipper upward and outward through the hair, trimming just a little at a time.

Repeat around sides and back of head.

If you want hair to be even shorter:

A) Apply more pressure to the head with the attachment comb that is in place. This takes a little practice, of course.

OR

B) Just switch to a shorter attachment comb. Remember, it’s better to leave too much hair than too little. For longer hair on top, use the barber comb and lift hair on the top of the head, cutting over the comb. Or, hold the hair between the fingers and cut to desired length. Always working from the front to the back of the head, gradually cut the hair shorter by reducing the space between the comb or fingers and the head. Comb often to check for uneven strands, and to get rid of trimmed hair.

OUTLINING:

Outlining requires no attachments. Comb hair into the desired style. Position the clipper between the sideburns and the ear (see above), making sure the corner edge of the blade is against the hairline. With the outline of the hair as your guide, slowly move the clipper over, around and behind the ears. For the back of the neck and the sideburns, hold the clipper upside down (see Fig. 1) and, holding it against the skin at the length desired, move the clipper downward.

STOP. COMB CHECK.

For best results, do as the professionals do: comb hair often, and check clipping results as you comb. This way you avoid uneven sides, bangs, neckline, etc.

SHORT CUTS TO PERFECT FLAT TOPS, CREW CUTS, ETC.

Always cut from the back of the neck to the crown, using the longest comb setting. Hold the comb attachment flat against the head and slowly move the clipper up through the hair. Use the same technique for the sides, cutting from the bottom to the upper side of the head.

For the front to the crown, cut the hair against the direction in which it grows. Then even it up with the sides.

For a flat top, use the flat comb, not the attachment comb. Just cut hair on top of the head over the flat comb (see Fig. 2).

To taper hair down to the neckline, use attachment comb #1. Comb hair and check for uneven spots. Outline sideburns and neck areas (see “Outlining”).

USER-MAINTENANCE INSTRUCTIONS CARE OF YOUR CLIPPERS

MAINTENANCE OF THE BLADE

Always apply oil to the blades before, during and after use. This will ensure maximum cutting performance. Hold clipper away from your body in a downward position and apply oil on the front and sides of the cutter blade. Wipe excess oil off with a soft dry cloth.

Conair® hair clippers are carefully inspected to insure that the blades are in perfect alignment. You will need to realign the blades if they should be knocked out of alignment. How can you tell if the blades need realigning? Simply match them up, point for point, to conform with the drawing below.

To replace cutting comb and cutter after removal for cleaning, replacement or because they are out of alignment, slide the cutter back onto the black plastic oscillating head. Next, you must make sure that the cutter (small blade) and the cutting comb (large blade) are properly aligned. Line up the new or existing cutting comb with the two screw holes. Place the original screws, one in each hole, and lightly tighten with a Phillips head screwdriver.

Then, match the two blades up, point to point, conforming with the illustration below in Fig. 4.

* The top edge of the cutting comb should be 1/32″ to 1/16″ (.79 mm. to 1.59 mm.) higher than the top edge of the cutter. This is important so that the clipper does not cut too close or come in contact with the skin.
* The extreme left tooth of the cutting comb must cover or be to the extreme left of the first small tooth of the cutter.
* Be sure that the extreme right big tooth of the cutter touches the extreme right tooth of the cutting comb.

Any other servicing should be performed by an authorized service representative or that the appliance has no user-serviceable parts. The product is for household use. Do not pull, twist, or wrap line cord around appliance.

SPECIAL OIL

To maintain the blades of your Conair® clipper, always apply oil to the blades before, during and after use. Gently place a few drops of oil on the teeth of the blades, using the special Conair® oil included with your set. Turn the clipper on for a minute, then turn off. This light, natural oil was formulated specifically for the Conair® high-speed clipper. Because it is the right oil to use, it will not slow down the blades. Never use any other product. There is no substitute for Conair oil.

POWER SCREW

The power screw permits you to adjust power to your clipper. You may need to make this adjustment if the power in your house is low. (The Conair® clipper was designed for household use.)

1. With a screwdriver or a dime, turn the power screw counterclockwise until the arm strikes a coil, making a clacking noise (Fig.1).
   
2. Turn the screw clockwise until the noise stops, and then turn about 45 degrees more. This is the maximum power setting (Fig. 2).
   

ADJUSTABLE TAPER LEVER

Just like professional clippers, the Conair taper lever is positioned at your thumb. You can hold the clipper in your hand and adjust the lever at the same time…while you’re clipping. This taper lever eliminates the need for an attachment comb because it lets you gradually adjust the closeness of the cut. For the closest cut and the shortest hair, push taper lever up as far as it will go. To increase cutting length, slowly push lever down. If you push to the lowest position, it will leave hair about the same length as the short attachment.

Because a different cutting edge is used in each setting, the taper lever lengthens the life of your blades.

Packed-in hair can slow down any clipper. To remove hair without removing the blades, use your cleaning brush to brush hair out of the blades. This should be done after each use. When blades are free of hair, apply a small amount of oil across them.

If you do this after every clipping, especially with heavy hair cutting, the blades should remain in good working condition. If clipper stops cutting and this action doesn’t help, check the blades. If they’ve become dull, replace them. For new blades, send check or money order for $6.50 (see order blank.) This price includes postage and handling, but $10.00 minimum must be met.

Conair Corporation 150 Milford Rd. East Windsor, NJ 08520

CAUTION: Never pull on the clipper cord. Never twist or wrap the cord around the clipper. Lay it flat with the cord coiled up when not in use.

WARNING: IF YOU THINK THE POWER IS OFF WHEN THE SWITCH IS OFF, YOU’RE WRONG.
KEEP AWAY FROM WATER

Everyone knows that electricity and water are a dangerous combination. But did you know that an electric appliance is still electrically alive even if the switch is off? If the plug is in, the power is on. So when you are not using your appliances, keep them unplugged.

ALWAYS UNPLUG SMALL APPLIANCES

LIMITED FIVE YEAR WARRANTY

Conair will repair or replace (at our option) your unit free of charge for 60 months from the date of purchase if the appliance is defective in workmanship or materials.

To obtain service under this warranty, return the defective product to the service center listed below, together with your purchase receipt and $3.00 for postage and handling. California residents need only provide proof of purchase and should call 1-800-3660937 for shipping instructions. In the absence of a purchase receipt, the warranty period shall be 60 months from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 60-MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

© 2010 Conair Corporation SERVICE CENTER CONAIR CORPORATION Service Department 7475 North Glen Harbor Blvd. Glendale, AZ 85307

Once again, thanks for buying a Conair product.
Your Conair® clipper blades are made of high carbon stainless steel. They are engineered for precise, professional results. If blades feel like they are pulling or grabbing hair, it means they are losing their sharpness and should be replaced as soon as possible.
Attachment combs should also be replaced if they are lost or broken. It is easier to cut hair with the accuracy of a pro when the necessary tools are at your fingertips.
Conair makes a variety of accessories for different haircut kits. If your haircut kit does not include them, you may want to consider adding them to your professional haircutting tools.
Left and right ear attachment combs provide effortless, precise cutting around the ears. Styling clips hold hair in place when you are sectioning hair. A styling comb makes it easy to taper or cut hair at an angle. A barber cape ensures a comfortable and neat haircut and a convenient storage pouch keeps all your essentials in one place.
Last but not least, an easy-to-follow 30-minute “Haircuts at Home” video is available. It demonstrates basic haircutting techniques and follows four popular haircuts step by step. It will give you the confidence and instruction you need to give. great-looking haircuts to every member of your family.
To register your Conair product, please simply go to www.conair.com/registration and the site will guide you.

EXCITING ITEMS FROM CONAIR

PT1 Mighty Mini 15-Piece Clipper Kit

Powerful DC motor makes this unique, lightweight clipper/ trimmer a versatile cutting instrument, as it can also be used for detailing and bikini line trimming.

GMT189CGB 13-Piece Trimmer

Rechargeable Beard & Mustache trimmer with stainless steel blades and a 5-position attachment comb for a blended and tapered trim.

HAIRCUT KIT REPLACEMENT PARTS & ACCESSORIES ORDER FORM

Pricing in effect through June 1, 2011. Orders postmarked after this date will be accepted, and the customer will be notified if pricing has changed.

Enclose check or money order made payable to Conair. (We cannot accept cash, stamps or C.O.D. orders.) *CT, IL, AZ, and PA residents should add applicable state sales tax. Minimum order of $10.00 or a $2.00 handling charge will be added to order. All prices include handling and return postage. Prices are subject to change without notice. Prices are valid only for shipments within the continental United States. Please allow 4­6 weeks for delivery. To avoid delays, please print clearly. We must have a street address, as UPS cannot deliver to a P.O. box.

NAME______________________________________________________________________________________
ADDRESS________________________________________________________ APT._______________________
CITY___________________________________________________________STATE____________ZIP________

TELEPHONE (        )___________________________________ (We call only if we have a question about your order.)

For information on other Conair ® haircut kit parts, call: 1-800-3-CONAIR.

Mail to:
Conair Corporation Service Department 150 Milford Road East Windsor, NJ 08520-9730

www.conair.com

CONAIR GS108 Turbo Extreme Steam 2-In-1

GETTING TO KNOW YOUR STEAMER

2-IN-1 ATTACHMENT

(A) Silicone Band -Pulls fabric taut for easier steaming.
(B) Bristle Brush -Loosens fibers for better steam penetration.
(C) Delicates Bonnet -Helps protect delicate fabrics and trims.
(D) Creaser -For perfect pleats and folds.

IMPORTANT: FOR HOUSEHOLD USE ONLY

FILLING INSTRUCTIONS

1. Make sure the unit is unplugged.
2. Stand the unit on a table and grasp with one hand.
3. Pull the reservoir out, away from the steamer body.
4. The rubber inlet cover is located on the top of the water reservoir.
5. Open the inlet cover and fill the reservoir with distilled water (which can be found in grocery stores). We recommend that you use distilled water only, as this will prevent mineral deposits in the boiler that can reduce performance or clog the water system.
6. Close the inlet cover and return the reservoir to its place, making sure that it snaps in place and is secure.

SUPPLIER’S DECLARATION OF CONFORMITY

Brand: Conair®
Model No.: GS108
Description: Handheld SteamerResponsible Party: Conair Corporation, 1 Cummings Point Road, Stamford, CT 06902 (203) 351-9000
Standards: FCC Part 15 Subpart B, ANSI C63.4-2014 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
DATE OF ISSUE: 10/09/2020

FEDERAL COMMUNICATIONS COMMISSION NOTICE

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially when children are present, basic safety precautions should always be taken, including the following:

READ ALL INSTRUCTIONS BEFORE USING
DANGER – Any appliance is electrically live even when the switch is off.
To reduce the risk of death by electric shock:

1. Always unplug appliance immediately after use and before cleaning.
2. Do not place or store appliance where it can fall or be pulled into a tub or sink.
3. Do not place in or drop into water or other liquids.
4. Do not reach for an appliance that has fallen into water. Unplug immediately.
5. Use only in a dry area.

WARNING – To reduce the risk of burns, electrocution, fire, or injury to persons:

1. This appliance should never be left unattended when plugged in.
2. This appliance is not a toy and is not to be used by children.
3. Close supervision is necessary when this appliance is used near children or individuals with certain disabilities. Unsupervised use could result in fire or personal injury.
4. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
5. Rest the appliance on a stable surface when placing on its base.
6. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged,or if it has been dropped into water. Do not attempt to repair the appliance. Incorrect reassembly or repair could cause a risk of fire, electric shock, or injury to persons when the appliance is used. Return the appliance to an authorized service center for examination and repair.
7. Keep the cord away from heated surfaces.Do not allow cord to contact heated surfaces.Do not pull or twist cord. Let appliance cool completely before putting away. Loop cord loosely around appliance when storing.
8. To reduce the risk of electric shock, this appliance has a polarized plug (one blade iswider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
9. Never drop or insert any object into any opening.
10. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
11. If an extension cord is absolutely necessary,a 15 ampere-rated cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that the cord cannot be pulled or tripped over.
12. Surfaces of this appliance are hot when in use. Do not let heated surfaces touch eyes or skin.
13. Do not place the steam nozzle directly on any surface or on the appliance power cord while it is hot or plugged in.
14. Unplug this appliance before filling or emptying the water container and when not in use.
15. Do not operate steamer without properly filling the water container with distilled water.
16. Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect.
17. Burns could occur from touching hot surfaces, hot water, or steam. Use care when removing water reservoir or when you turn a steam appliance upside down – there may be hot water in reservoir. Always position steamer with head away from you and any other person when turning on.
18. Do not hold hand in front of steam.
19. To reduce likelihood of circuit overload, do not operate another high-wattage appliance on the same circuit.
20. Use caution when installing or removing an attachment, as it may contain hot water from condensation. Ensure that the unit is off, attachment is dry or cooled off to avoid contact with hot water.
21. Never steam clothes you, or someone else,are wearing.
22. When emitting steam, this appliance may cause burns if it is used too close to the skin or eyes, or if it is used incorrectly. To reduce the risk of contact with hot water emitting from the steam vents, test appliance before use by holding it away from the body.

OPERATING INSTRUCTIONS

1. Fill water reservoir with distilled water.
2. Plug the unit into the electrical outlet.
3. Press the ON/OFF button located on the back of the steamer to turn the unit on. The HIGH SETTING light will illuminate and begin blinking. Allow 10 seconds for the unit to warm up. The appliance is ready to use when the HIGH SETTING light stops blinking and remains solid.
4. This steamer has a dry iron setting. Without pressing the STEAM button, the soleplate of the steamer will get hot to use as an iron.
5. The steamer has 4 steam settings. Press the MODE button repeatedly until you reach desired setting. Choose LOW for use on delicate fabrics, up to TURBO for use on thicker fabrics and heavily wrinkled articles.
6. Press the STEAM button to emit steam. Pick up steamer and begin steaming, pointing the jets away from you and anyone in the room.
   NOTE: This steamer has a SMART TOUCH SENSOR feature. Steam will not emit until steamer is picked up from flat surface.
7. To activate SMART TOUCH SENSOR, hold the MODE button for 2 seconds until lights are flashing. Once lights are flashing, the SMART TOUCH SENSOR has been activated. Once steamer is placed down on a flat surface, SMART TOUCH SENSOR goes into auto pause. To restart the steamer again, simply pick up steamer and begin steaming.
8. Press ON/OFF button to turn unit OFF.
9. Unplug the device when it is not in use.

SANITIZING INSTRUCTIONS

1. Position the garment steamer’s soleplate at a minimum distance of 0.4 inch (1 cm) from material to be treated.
2. Remain steaming in this position for 1 minute, then move to the next area to be treated and repeat.

ATTACHMENTS

CREASER ATTACHMENT – Creates a crease in pants, shirts, blouses and more.
DELICATES BONNET – protects trims and safely steam fine fabrics.

2-IN-1 ATTACHMENT Silicone Band – pulls fabric taut for better results.
Bristle Brush – ensures steam penetrates fibers for a perfect press, even on heavy fabrics.

USING ATTACHMENTS
With the garment steamer off and cool, snap the Silicone Band, creaser or delicates bonnet attachment over the steam head, ensuring it is firmly affixed. At this point, for the 2-in-1 attachment, the Silicone Band can be used or you can choose to affix either the Bristle Brush insert into the channel on the top of the Silicone Band attachment, as desired. NOTE: Only one function of the 2-In-1 attachment can be used at a time.

CAUTION: Use extreme care when changing the attachments after the unit has been in use, as the steam head will continue to be hot.

STEAMING TIPS

1. First, test unit on an inconspicuous area of the item to be steamed using the lowest STEAM setting to ensure fabric can tolerate the effects of steam. If there is no evidence of damage, you can proceed to use the steamer on that item.
2. To prepare your fabric for steaming, brush it with the brush attachment. This will loosen the fibers and allow better steam penetration.
3. Hang your garment or fabric.
   NOTE: Avoid using metal clothes hangers, if possible.
   CAUTION: If hanging garment on a door while steaming, be careful not to damage the door with steam.
4. Pass the steam jets just above the fabric where the wrinkles are. It may take a few passes to remove the wrinkles completely.
5. For heavier fabrics or severely wrinkled fabrics, you may position the steamer head directly on the fabric for a few seconds to remove wrinkles. Be cautious when working with delicate fabrics.
6. After use, turn unit off by depressing the STEAM button. Then press the ON/OFF button to the OFF position. With dry hands, unplug your garment steamer from the outlet. Empty any remaining water from the tank to avoid leakage. BE SURE TO PRESS THE ON/OFF BUTTON TO THE OFF POSITION PRIOR TO UNPLUGGING THE UNIT.
7. When steaming, always keep the unit in motion. Do not continuously hold steamer over one area or touch steamer jets directly to fabric for more than a few seconds, as this can cause damage, including shrinkage, melting, or color shift on certain types of material.
8. In the case of heavier, durable fabrics, such as wool coats or bedding, the TURBO setting and slower passes with the steamer may be necessary to achieve desired results. As always, start by testing on an inconspicuous area of the item to be steamed, using the regular steam setting to ensure fabric can tolerate the effects of steam, and adjust your technique as needed to obtain the results desired.

LIMITED ONE-YEAR WARRANTY

(U.S. AND CANADA ONLY)
Conair will repair or replace (at our option) your unit free of charge for 12 months from the date of purchase if the appliance is defective in workmanship or materials.
To obtain service under this warranty, return the defective product to the service center listed, together with your purchase receipt.
California residents need only provide proof of purchase and should call 1-800-3-CONAIR for shipping instructions. In the absence of a purchase receipt, the warranty period shall be 12 months from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 12-MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER.

Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

CONAIR GARMENT STEAMING ACCESSORIES

Due to continuing product improvements, the actual product purchased may differ slightly from the one shown.

Service Center
Conair Corporation
Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307
For information on any Conair product, call 1-800-3-CONAIR or visit us on the web at www.conair.com
Please register this product at www.conair.com/registration

©2021 Conair Corporation
Made in China