Pawever Pets PPEGGINB24A Fully Automatic Digital Egg Incubator

INSTALLATION

1. Insert one end of power cord into the socket on the device.
2. Ensure that the egg troy matches the motor shaft connector.
3. Ensure that the egg troy matches the slots on both sides.
4. Ensure that the fan, temperature display, function keys and heater are functional.
   If the ambient temperature goes below 20°C, place the protective foam around the incubator.
5. Add water to preheat the incubator for 20-30 minutes.

OPERATION

Selecting Fertilised Eggs

• Fertilised eggs must be fresh -within 4-7 days after laying is the best. The best temperature for saving fertilised eggs is 10-15°C.
• Ensure the eggshell has no deformity, cracks or spots.
• Generally, disinfection is not required and may reduce the hatching rate.

Incubation Process

1. Place in the incubator with the narrower end facing down.
2. Proper operation and careful observation are required during the incubation.
   Ensure you add water to the machine every 1 to 2 days (depending on the environment and the quantity of water inside the machine).
3. Test the eggs for the first time after 5 to 6 days to confirm fertilisation and identify, the unfertilised eggs, scattered yellow eggs and dead eggs.
   Do NOT test during the first 4 days or the incubator and egg surface temperature may decline sharply and affect the eggs’ early development.
4. Test the eggs for the second time after 11 to 12 days to check the development of the embryo. A well-developed embryo is enlarged, with blood vessels inside and the air chamber is large and sharply demarcated.
5. Test the eggs for the third time after 16 to 17 days. A well-developed embryo will be large and little light will be visible when light is shone from the wider end.
   If it’s a dead egg, the blood vessels in the egg will be blurred, parts near the air chamber will be yellow and the boundary between the egg and the air chamber will be unclear.
6. Increase humidity and decrease temperature during the hatching period in order to prevent water from evaporating too quickly in the eggs. This will regulate the humidity and temperature while avoiding dehydration. The temperature should be no higher than 37.5°C on day 19-21.

Controller

Testing Incubator for the first time

1. Set up the in cubator as per Installation
2. Turn the incubator on.
3. An alarm indicating low temperature/humidity will sound. this is normal: press any button to cancel the alorm.
4. Operate the in cubator and fill the water channels: the humidity reading will increase.
5. Place the eggs in the incubator with the narrower end facing down.
6. Press the reset button to check the automatic egg turning function. It turns for 10 seconds every 2 hours.

Setting the temperature

1. Press SET once.
2. Use the up and down buttons to select the desired temperature.
3. Press “SET” once more to exit.

The recommended temperature to set is 37.6’C.

Setting the temperature alann (AL and AH)
Low temperature alarm (AL)

1. Press and hold SET for 3 seconds.
2. Press SET to toggle options until •AL• appears in the temperature display.
3. Use the up and down buttons to select the desired temperature alorm settings.

High temperature alarm (AH)

1. Press and hold SET for 3 seconds.
2. Press SET to toggle options until “AH” appears in the temperature display.
3. Use the up and down buttons to select the desired temperature alorm settings.

It is recommended to leave these parameters at the factory default of1 °C above or below the set temperature.

Setting the humidity alann (AS)

1. Press and hold SET for 3 seconds.
2. Press SET to toggle options until •fJ,S” appears in the temperature display.
3. Use the up and down buttons to set the desired humidity alarm settings.

It is recommended to leave these parameters at the factory default of 45%.

Calibrating temperature sen110r reading (CS)
If the thermometer’s reading is too high or Low, it con be adjusted.

1. Press and hold SET for 3 seconds.
2. Press SET to toggle options until ·cs” appears in the temperature display.
3. Use the up and down buttons to set the desired

The factory default is 0°C (a calibration will be offset from this value).

Setting maximum and minimum temperature (HS and LS)
This determines the maximum and minimum temperature selectable to prevent accidental out-of-range temperature selection.

1. Press and hold SET for 3 seconds.
2. Press SET to toggle options until •HS” (high temperature setting) or ·Ls” (low temperature setting) appears in the temperature display.
3. Use the up and down buttons to set the desired maximum or minimum temperature.

The factory defaults are 39.5°C HS and 30°C LS.

Incubating tips

Egg and incubator hygiene

• Proper hygiene is essential to achieve good hatching results. Poor hygiene can cause early death in chicks.
• Only clean eggs should be used for incubation. Dirty eggs are potential carriers of diseases that thrive and multiply in the ideal heat and moisture conditions of the incubator. If you need to incubate dirty eggs, wash them first in warm water (44- 49″C) that contains disinfectant at a rate recommended by the manufacturer (most household disinfectants ore suitable) and dry the eggs quickly after washing using separate paper towels.
• Do not soak eggs for long)er than four minutes (this can affect fertility) and do not soak eggs in cold water (this encourages bacterial penetration through the eggshell).
• Fumigating eggs immediately after collection also helps with hygiene. A suitable fumigant is formaldehyde gas. which is made by mixing 1 part (by weight) of potassium permanganate (Condy’s crystals) with 1.5 parts (by volume) of formalin (see Table 1 for the correct amounts for each application). Place the chemicals in a dish on the floor of the incubator. Place the potassium permanganate into the dish and pour the formalin over it. Shut the incubator door quickly and vacate the room.
• For proper fumigation, run the machine normally with the correct temperature and humidity. After 20 minutes, open the vents or the door and air the machine for a few minutes. Again, vacate the room.

Healthy stock

• It is important that eggs from only a healthy flock are used for hatching, as some diseases can be transmitted through the egg. The egg-transmittable diseases to be most aware of are salmonella infections, fowl typhoid and Mycoplasma gallisepticum.
• Eggs laid by birds infected with disease may fail to hatch. Of those that do hatch, some birds may die during brooding and the survivors may act as carriers and infect healthy chicks.
• Do not add eggs from unknown sources to make up numbers, as you risk infecting your flock.

Breeding stock nutrition

• The egg provides a complete food store for proper embryo development except gaseous oxygen, which enters the egg through pores in the shell Breeding stock must be fed a well-balanced diet to fully meet the embryos’ nutrient requirements.
• The deficient nutrients are usually vitamins or minerals. A deficiency of these in the breeders’ diet may not show any ill effects in the breeders, though hatchability may be affected, which is why different categories are fed specific diets. Nutritional deficiencies, such as a lack of riboflavin, are the main causes of embryo mortality during the middle stage of incubation O.e. between the 12th and 14th days}.
• Hens’ vitamin and mineral requirements for laying eggs are lower than those of breeders. The breeder’s diet should begin six to eight weeks before hatching eggs are required, with particular attention to vitamin A. D3, riboflavin, pantothenic acid, biotin, folic acid, vitamin 812 and the mineral manganese.

TROUBLESHOOTING

Frequently Asked Questions

How do I store eggs?
Eggs must settle for at least 24 hours if sent through the post to allow the air cell inside to return to its normal size. Eggs should always be stored with the narrower end down.
If you receive eggs that are getting old, you may only let them settle overnight.

When will the incubator be ready to use?
The incubator should run for at least 24 hours and ideally a week before placing the eggs in them so that you can be familiar with its operation and make any necessary adjustments.
Note that the incubator’s internal temperature is not the same as the egg’s internal temperature. The temperature in an incubator will vary over time, rising and lowering. The temperature inside the egg will be an average of the incubator’s temperature over time.

How long does it take to incubate chicken eggs?
The incubation period for chicken eggs is 21 days. You should turn your eggs at least three times a day for the first 18 days and stop turning after the 18th day (or use a hatcher if you have eggs from different days in the same machine).
This allows the chick time to orient itself inside the egg. After day 18, keep the incubator closed except to add water. This will help bring the humidity up to help the chicks hatch.

What are the appropriate temperature and humidity?
Fan forced incubator: 37.5°C measured anywhere in the incubator. Humidity: 55% for the first 18 days, 60-65% for the lost 3 days in the hatcher.

How can I tell my thermometer is accurate?
The incubator’s thermometer will be accurate, and you con observe the results of the first hatch and adjust accordingly for future hatches if the temperature appears to have been slightly too high or too low. It is recommended to keep notes on everything you do during the incubation period so as you learn, you’ll have these notes to look back on.
You con also adjust the thermometer by comparing with a calibrated thermometer as described in CaUbrattng tempered.re sensor reading (CS).

How do I check humidity?
humidity is checked by woy of o hygrometer (wet-bulb thermometer) in conjunction with o regular dry-bulb” thermometer. A hygrometer is simply o thermometer with o piece of wick attached to the bulb. The wick hangs in water to keep the bulb wet (hence the nome •wet­ bulb thermometer”). When you read the temperature on the thermometer and hygrometer, you must then compare the readings too chart to translate from wet-bulb/dry-bulb reading to “percentage humidity”.

• 60% humidity reads about 30.5°C on a wet-bulb ot 37.5°C.
• 60% humidity reads about 31.6°C on o wet-bulb at 38.6°C.
• 80% humidity reads about 33.8°C on a wet-bulb ot 37.5°C.
• 80% humidity reads about 35°C on a wet-bulb ot 38.6°C.

Getting your humidity to become as accurate as your temperature is nearly impossible. It is almost completely impossible with o small incubator.Try to get your humidity as close os you con – within 10-15% is usually sufficient.

How do I regulate humidity?
To regulate humidity. you need to change the surface area of water in your incubator.
Surface area is the amount of surface of water exposed to air in your incubator. The depth of water has no bearing on the humidity in the incubator (unless the depth is zero).
If the humidity is too low in your incubator, add surface area. Place another pan of water in the incubator or some small wet sponges.
This will help; alternatively, you can spray the eggs with a fine mist. To decrease the humidity, remove surface area. Use small containers of water or undo some of the things you’ve added.
The humidity will need to be adjusted differently depending on the season and outside conditions

IN THE BOX

• 1 x Incubator
• 1 x Quick start guide
• 1 x Protective foam
• 1 x Power cord
• 1 x Water kettle

Need more information?
This is a Quick Start Gulde, and we hope thot this has given you the assistance needed for a simple set-up. For the most up-to-date guide for your product. as well as any additional assistance you may require, head online to help.kogan.com

Attention
Please handle this product with care and inspect it regularly to ensure it is in good working order.
If the product, power supply cord or plug shows any signs of damage: stop use, unplug, and contact Kogan.com/support.

Safety & Warnings

• Read all instructions before using the appliance and retain for reference.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Do not use outside of indoor household use as described in this manual.
• Always unplug by the plug and do not pull the cord or touch with wet hands.
• Do not allow the power cord to be exposed to water, heat, direct sunlight or overhang where it can be pulled or otherwise be damaged or pose a hazard.
IMPORTANT: Always switch the power off before opening the filter cover.

Overview

Parts

Specifications     

Operation

1.  As per the diagram, undo the clasps labeled 1 and 2 to separate the main body and head.
2.  Install the draining container and medium filter into the main body in turn. Press firmly to combine the main body and head. Then refasten the clasps.
3.  Pull the securing buckles to expose the connections for the input and output pipes. Install and fasten input and output pipes with nuts. When connected, press the securing buckles to fix in position.
4.  As per the above diagram, install the input and output curved bars in the aquarium. NOTE: The output bar has a spray bar and the input bar has a filter entrance.5. As per the above diagram, press the blue buckle forcibly once. The blue buckle will rebound. The input bar will absorb water into main body at the same time, forcing air out of main body through output bar. When the level of water in output bar is equal to the level of aquarium, you may power on the aquarium.

Water intake/drainage hose assembly

If the above steps do not rectify any issue you are facing, contact Kogan Support.

User manual is subject to change without notice. For the latest version of your user manual, please visit http://www.kocian.com/usermanuals/