Instruction Manual

MODEL: VTA-754B

CAUTION: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
WARNING: To prevent electric shock, do not use this (polarized) plug with an extension cord, receptacle
or other outlet unless the blades can be fully inserted to prevent blade exposure.

WARNING: Invisible laser radiation when open and interlock failed or defeated. Avoid direct
exposure to laser beam.

Important Safety Instructions

1. Read these instructions – All the safety and operating instructions should be read before this product
   is operated.
2. Keep these instructions –The safety and operating instructions should be retained for future reference.
3. Heed all warnings – All warnings on the appliance and in the operating instructions should be
   adhered to.
4. Follow all instructions – All operating and use instructions should be followed.
5. Do not use this apparatus near water – The appliance should not be used near water or moisture –
   for example, in a wet basement or near a swimming pool, and the like.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiations, heat registers, stoves, or other apparatus
   (including amplifiers) that produce heat.
9.  Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two blades
   with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide
   blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet,
   consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at the plugs, convenience
    receptacles, and at the point where they exit from the apparatus.
11.  Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
    manufacturer, or sold with the apparatus. When a cart or rack is used,
    use caution when moving the cart/apparatus combination to avoid
    injury from tip-over.
13. Unplug the apparatus during lighting storms or when unused for
    long periods of time.
14. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been
    damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled
    or objects have fallen into the apparatus has been exposed to rain or moisture, does not
    operate normally, or has been dropped.
15. 

-This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the
presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock.
-Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no
user-serviceable parts inside. Refer servicing to qualified personnel.
-The exclamation point within and equilateral triangle is intended to alert the user to the presence of
important operating and maintenance instructions in the literature accompanying the appliance.
 16.  The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
 17.   WARNING
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The
apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as
vases, shall not be placed on apparatus.
 18.  The use of the equipment in moderate climate.
 19.  The ventilation should not be impeded by covering the ventilation openings with items such as
newspapers, tablecloths, curtains, etc.
 20.  No naked flame sources, such as lighted candles, should be placed on the apparatus.
 21. The symbol with Indication AC voltage.
22.  CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the
risk of electric shock, do not perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.

 23 This equipment is a Class Ⅱ or double insulated electrical appliance. It has been designed
in such a way that it does not require a safety connection to electrical earth.

 24.  The batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as
sunshine, fire or the like.
25.  Attention should be drawn to the environmental aspects of battery disposal.

ACCESSORIES INCLUDED

• REMOTE CONTROL
• INSTRUCTION MANUAL
• WARRANTY (BACK OF MANUAL)
• 45 RPM ADAPTER
• CD SOFTWARE
• USB CABLE
•  3 REPLACEMENT NEEDLES
• 1 VINYL CLEANING CLOTH
• 10 RECORD SLEEVES
• RCA LINE OUT CABLE

Product Overview

Front View

1. REPEAT: In CD or USB mode, press to
   select a repeat mode.
2. SHUFFLE: In CD or USB mode, press
   for shuffle playback.
3. PROGRAM: In CD or USB mode, while
   the CD or USB is stopped, press to
   program tracks.
4. &5. FOLDER + & FOLDER- : In USB
   mode, press to choose your
   desired folder.
5. VOLUME KNOB: Turn to adjust
   volume. (Note: volume ranges from
   00 to 30.)
6. DISPLAY
7. POWER: Push to turn the unit on or off.
8. 3.5mm HEADPHONE JACK: Accepts
   headphone/earphone plugs
9.  BT/USB: Press to switch to Bluetooth
   or USB mode.
10. PHONO: Press to enter to Phono
    mode.
11. CD/AUX: Press to switch to CD
    or AUX mode.
12. TAPE: Press to enter to cassette
    tape mode.
13. FM: Press to enter to FM mode.
14. TUNING: In FM mode, turn to tune
    in station.
15. USB JACK
16. AUX-IN JACK: Connect an external
    source to the AUX IN socket.
17. STOP : Press to stop playback.
18. &20. PREVIOUS / NEXT TRACK &
    REWIND / FF :
    In CD or USB Mode, press once to skip to
    the previous / next track.
    Press and hold to fast rewind / forward.
19. PLAY/PAUSE : Press to start
    playback. During playback, press again to
    pause.
20. OPEN/CLOSE : In CD mode, use to
    open and close the disc tray.
21. DISC TRAY
22. REMOTE SENSOR
23. FM SCALE
24. TUNED/ST INDICATOR: In FM Mode,
    the “TUNED/ST” indicator lights up red
    when tuning in a stereo reception station.

Right Side View

27. CASSETTE FF & EJECT: Press halfway to fast forward, press all the way to end
and eject the tape.

Rear View

 28.  FM WIRE ANTENNA
While tuned to a station in FM mode, extend the wire and reposition to adjust
for best reception.
 29.  AC POWER CORD
Plugs into a wall outlet.
30  USB JACK (Recording Only)
31. LINE OUT JACKS
For amplifier device with RCA auxiliary input sockets, insert the white and red plugs on the
RCA cable into the unit. Insert the opposite end into the amplifier device. Be sure to connect
the white plug to the white jack and the red plug to the red jack.

Parts of the Turntable

A. Turntable.
B. Safety Screw (for transport) Before using the unit, turn
the screw clockwise using a coin or screwdriver.
Important: When you transport the unit, turn the screw counterclockwise to secure the turntable.
C. Cue-lever Use this lever to lift the tone arm.
D. Speed Selector
E. Tone Arm Holder
F. Tone Arm Before use, completely loosen the fixed rope on the tone arm and lift the tone
arm up.
G. 45 RPM Adaptor

Setup

1. Remove white protective needle cover by gently pulling towards front of unit.
2. Remove any packaging materials from the unit.
3. Connect the AC power cord
   to a wall outlet.

Note: To prevent interference, avoid bundling audio signal cables together with the AC power cord.

Basic Operation

1. Push the POWER button to turn the unit on.
2. Select the source by pressing the corresponding button
   (USB / BT / PHONO / CD / AUX / TAPE / FM).
3.  Rotate the VOLUME knob to adjust to the desired sound level.

Listening through Earbuds/Headphones (not included)
For private listening, first reduce the volume level to minimum.
Insert your headphones’ plug into the 3.5mm jack, then
adjust the volume up by turning the VOLUME knob.

Note: The speakers will automatically be deactivated while
headphones are plugged in.

Listening through RCA LINE OUT
For amplifier device listening, first reduce the volume level to minimum. Insert the white and red
plugs on the RCA cable into the back of the unit, then insert the opposite end into your amplifier
device. Be sure to connect the white plug into the white jack and the red plug into the red jack.
CONDENSATION WARNING:
When the unit is moved from a cold or warm place, or is used following a sudden temperature change, there is the
danger that water vapor in the air may condense on the unit, preventing proper operation. In such cases, leave the
unit for 1-2 hours after plugging it into an AC outlet to allow it to stabilize at the temperature of its surroundings.

Remote Control

When using the remote control, point it towards the remote sensor on the front panel of the unit.
Notes:
– Even if the remote control is operated within the effective range, remote control operation may be
impossible if there are any obstacles between the unit and the remote control.
– If the remote control unit is operated near other devices, which generate infrared rays, it may not
function properly. Conversely, the other devices may not function incorrectly.

Battery Installation

1. Remove the battery compartment cover.
2. Insert 2x “AAA” batteries.
   Note: Make sure that they are oriented so their polarity
   markings, “+” and “-”, match the remote’s markings.
3. Replace the battery compartment cover.

Battery Replacement
When the operating distance between the remote control unit and main unit decreases, it is
necessary to replace the battery with new ones.

Battery Precautions
Be sure to insert the batteries with correct positive “+” and negative “-” orientation.
ALWAYS use batteries of the same type. Never mix different types of batteries together.
When using rechargeable batteries, refer to the precautions on their labels.
When the remote control unit is not to be used for a long time (more than a month), remove the
batteries to prevent them from leaking.
Do not heat or disassemble batteries, and NEVER dispose of old batteries by throwing them in a fire.
Do not dispose device into standard garbage disposal sites. Dispose of device at available Battery
Recycling Sites after fully discharging battery. Not doing so may violate disposal laws and
regulations.
Please refer to local regulations for proper battery disposal.

Remote Control Button Functions

1. OPEN/CLOSE: Press to open/close the disc tray.
   (Note: This button will only work in CD mode)
2. PHONO: Press to enter PHONO mode.
3.  FM: Press to enter FM mode.
4. Bluetooth: Press to enter Bluetooth mode.
5.  TAPE: Press to enter Cassette mode.
6. &15. FOLDER+ / FOLDER- : In USB mode, press to choose
   your desired folder.
7. PROGRAM: In CD or USB mode, while CD or USB is
   stopped, press to program tracks.
8. REPEAT: In CD or USB mode, press to select repeat playback.
9. STOP : Press to stop playback.
10. 10&20. VOL+ / VOL- : Press to adjust the volume.
11. &18. Previous / Next Track & Fast Rewind / Forward :
12. CD or USB Mode, press once to skip to the previous / next track.
    Press and hold to fast rewind / forward.
13.  CD: Press to enter CD mode.
14.  AUX: Press to enter AUX mode.
15. USB: Press to enter USB mode.
16. SHUFFLE: In CD or USB mode, press for shuffle playback.
17.  PAIR: In Bluetooth mode, press shortly to disconnect current device.
    Press again to reconnect the device that has been connected before.
18.  PLAY/PAUSE : Press to start playback, press again to pause.

Listening to a Vinyl Record

1. Press the “PHONO” button, “PHONO” will appear
   on the display.
2. Gently open the top cover. Note: Be careful not to pinch your finger when
   opening /closing the top cover.
3.  Place a vinyl record on the turntable. When playing a
   45 RPM record, use the included adaptor.
4. Select the appropriate speed (4).
5. Gently push tone arm clip (5)
   to the right to release the tone arm.
6.  Raise the cue lever (6) to lift the tone arm off the tone arm support.
7. Move the tone arm gently to the edge of the record (or the starting point of a track).
   The turntable will begin to turn.
8.  Gently lower the tone arm by slowly releasing the cue lever.
9.  When the record reaches to its end, tone arm and rotation stop. Lift the tone arm and place
   it to tone arm rest manually.
   Important:
   – Closing the top cover will help prevent dust from settling on the turntable.
   – Always relock the tone arm clip before transporting the unit.
   – Do not place anything on top of the turntable cover, especially while playing a record.

Listening to a CD

1. Press the CD/AUX button to switch to CD mode.
Note: When no disc is set, “NO DISC” will appear on the display.
2. Press the OPEN/CLOSE button.
Note: This button will only work in CD mode.
3. Place a disc on the tray with the printed label face up.
4. Press the OPEN/CLOSE button to close the tray.
Note: “READ” will blink for a few seconds.
5. The number of tracks will show on the display. And then it will begin playback from
the first track automatically.
6. To temporarily pause playback, press the PLAY/PAUSE button Press again to resume.
7. To skip tracks backward or forward, press the corresponding skip button .
Pressing once will restart the current track.
Pressing twice in succession will return to the beginning of the previous track.
8. To fast rewind / forward within a track, press and hold down the corresponding skip button
or until the desired position is reached.
9. To stop playback, press the STOP button.

Important:
– Never place more than one disc on the tray.
– The disc must be placed in the center of the disc tray. An incorrectly loaded disc

can permanently damage the tray door mechanism.
– Do not push the CD tray – always use the OPEN/CLOSE button.
– It takes a moment for the unit to load a disc, during which all buttons will be
temporarily deactivated.

Repeat Playback
Each time the REPEAT button is pressed, the repeat mode will cycle through the following options:

REPEAT 1 (Repeat one track)
The current track will be played repeatedly. If you press the
button to select another track, the track you select will be played repeatedly.
REPEAT ALL (Repeat the entire CD)
The entire CD will be played repeatedly.
To cancel the repeat mode, press REPEAT button repeatedly till the
“REPEAT” icon disappears from the display.

Notes:
– If one of the following buttons is pressed, the repeat mode will be cancelled:
OPEN/CLOSE, FM, PHONO, CD/AUX, /USB, TAPE.
– Repeat playback works with finalized discs only.

Shuffle Playback
To play the tracks on a CD in a random sequence, press the SHUFFLE button during playback,
“SHUFFLE” will show on the top of the display. Press SHUFFLE again to cancel shuffle mode.

Notes:
– Pressing during shuffle playback will randomly
select the next track.
– If one of the following buttons is pressed, shuffle mode will be
cancelled: OPEN/CLOSE, FM, PHONO, CD/AUX, /USB, TAPE.
– When the SHUFFLE playback of all the tracks has been
finished, the unit stops and the shuffle mode is cancelled.
– A track cannot be repeated during shuffle playback.
– Shuffle playback does not work during programmed playback.
– Shuffle playback works with finalized discs only.

Programmed Playback
Up to 20 tracks can be programmed to play in the desired order.
Notes:
– Shuffle playback does not work during programmed playback.
– Programmed playback works with finalized discs only.

1.  Press “CD” to enter CD mode, then load a CD.
2. While the CD is stopped, press the PROGRAM button.
3. “PROGRAM” indicator blinks, and “P-01” appears on the display.
4.  Press to select a track number.
5.  Press the PROGRAM button again to set the current track.
6.  “P-02” is displayed. Repeat steps 4 through 5 to program the additional tracks.
7.  When the selection of track numbers has been finished, press the PLAY button( )to start
   program playback.
8. To cancel the program mode, press the STOP ( ) button twice and then the “PROGRAM” will
   disappear from the display.

To check the programmed order
In the stop mode, press repeatedly to show the track numbers that have
been programmed.

Listening to the Radio

1. Press the “FM” button. “RAD” will show on the display.
2. Tune to the desired station, using the Radio Tuner Knob.

Listening to an External Audio Device (AUX Mode)

Press the CD/AUX button to switch to AUX mode. “AUX” will show on the display.
In AUX (auxiliary) mode, this unit can play audio from an external device (iPod, MP3 Player, Portable
CD Player, etc.)
There is an AUX-IN jack on the front of the unit. When connecting a device that has a headphone
jack, use a 3.5mm cable on both ends to connect the external device with the apparatus.

1. Plug one end of the 3.5mm cable (not included) into the AUX-IN jack.
2. Plug the other end of the cable into the headphone jack of the external device.

NOTE: All operations are only available on your external device.

Listening to an External Audio Device (BT Mode)

1.  Press /USB button to switch to Bluetooth mode, and the display will flash “bLUE”.
2. On your external device turn ON the Bluetooth function.
   NOTE: The effective distance between your external device and this apparatus is
   10 meters (33ft).
3. Wait a moment for “Wooden Music Center” to appear on the devices list of your external
   device’s Bluetooth Menu. Press “Wooden Music Center” to connect to the unit. Sometimes a
   window will ask you for a password. Fill in “0000” then press “OK” on your external device.
4.  When the Bluetooth connection is successful, the “bLUE” on the display and the Bluetooth
   symbol will stop flashing.

NOTE:
– The PAIR Button will allow you to disconnect from your external device while remaining in BT
mode. Simply press the PAIR button to disconnect. Press it again to reconnect the device that has
been connected before.

Listening to a Cassette Tape

1. Load an audio cassette tape into the unit (located on the
   right side of the unit). Playback will automatically begin.
2. Press button halfway to Fast Forward the tape.
   Press button lightly and playback will resume.
3. Press button completely down to end playback and eject tape.

USB Memory Stick Playback

1. Press /USB button to switch to USB function. “USB” will appear on the display.
   Note: When no USB is inserted, “NO” will appear on the display.
2.  Insert the USB memory stick (not included) into the USB port and then it will begin playback
   automatically from the first track.
3.  To pause playback, press the PLAY/PAUSE button . Press again to resume.
4. To skip tracks backward or forward, press the corresponding skip button .
5.  To fast rewind / forward within a track, press and hold down the corresponding skip button
   until the desired position is reached.
6. Press the button FOLDER+ or FOLDER- to select your desired folder.
7. To stop playback, press the STOP ( ) button.

Repeat Playback
Each time the REPEAT button is pressed, the repeat mode will cycle through the following options:

REPEAT 1 (Repeat one track)
The “REPEAT 1” icon will appear on the display and the current track will
be played repeatedly. If you press the button to select
another track, the track you select will be played repeatedly.

REPEAT ALL (Repeat the entire USB)
The “REPEAT ALL” icon will show on the display and the entire USB will start to play repeatedly.
To cancel the repeat mode, press REPEAT button repeatedly until the “REPEAT” icon disappears
from the display.

Shuffle Playback

Press the SHUFFLE button for shuffle playback. The “SHUFFLE”
icon will appear on the display. Playing the tracks on a USB mode in
a random sequence.
Press it again to cancel the SHUFFLE playback, “SHUFFLE” will
disappear from the display.

Notes:
– Pressing   during shuffle playback will randomly select the next track.

– A track cannot be repeated during shuffle playback.
– Shuffle playback doesn’t work during programmed playback.
Programmed Playback
You can program up to 98 tracks for the USB.
Notes:
– Shuffle playback does not work during programmed playback.

1. Rotate to select USB function, then insert a USB memory stick into USB port.
2. While the USB is stopped, press the PROGRAM button.
3. “PROGRAM” icon will show and “P01” blinks on the display.
4.  Press to select a track number.
5.  Press the PROGRAM button again to set the next program track, “P02” appears and blinks.
   Repeat steps 4 through 5 to program the additional tracks.
6. When the selection of track numbers has been finished, press the PLAY/PAUSE
   button to start program playback.
   (Note: when all 98 program tracks are finalized, press the PROGRAM button
   once and “FI” will appear on the display)
7.  Press the STOP ( ) button to cancel the program mode and then
   the “PROGRAM” will disappear from the display.
   To check the programmed order
   In the stop mode, press repeatedly to show the track numbers
   that have been programmed.

USB Recording Operation

To properly record your vinyl to MP3 via computer, use the included USB Output Cable and
Instructional CD Software. Connect one end of the USB cable to the turntable (USB jack on the back
of the unit) and the other end into your computer. Then connect the AC power cord to the turntable.
To install and use the software on your computer, select the proper Mac or PC install files, then
follow the prompts provided on the Instructional CD.
For the most up to date manuals, software, instructional details, troubleshooting or other
downloadable content, please go to http://audacityteam.org

Maintenance / Proper Handling

Compact Disc Handling

• Always place the disc on the disc tray with the label side facing upward (compact discs can be played/recorded
  only on one side)
• To remove a disc from its storage case, press down on the center of the case and lift the disc
  upward, holding it carefully by its edges.
• To clean a disc, wipe the surface from the center hole outward towards the outer edge with a soft, dry cloth.
• Never use such chemicals as record spray, antistatic sprays or fluid, benzine or thinner to clean discs; they will
  irreparably damage the disc’s plastic surface.
• Discs should be returned to their cases after use to protect from dust and scratches.
•  Do not expose discs to direct sunlight, high humidity, or high temperature for extended periods of time.
•  Printable CD-R and CD-RW discs are not recommended, as the label side may become sticky and
  damage the unit.
• Use a soft oil-based felt-tipped pen to write information on the label side. Never use a ball-point or hard-tipped
  pen, as doing so may damage the recorded side.
• Do not use irregularly-shaped CDs (octagonal, heart shaped, business card size, etc), as they will
  damage the unit.
•  Read all precautions supplied with any CD-R or CD-RW disc.
• Never handle a disc with dirty fingers.
• Never insert a disc that has a crack on the surface.

Handling Vinyl Records

• Do not touch the record’s grooves. Only handle records by the edges or the label with clean hands. Touching
  the record surface will cause your record’s quality to deteriorate.
• To clean a record, use a soft anti-static cloth to gently wipe the record surface.
• Keep records in their protective sleeves when not in use.
• Always store records upright on their edges
• Avoid placing records in direct sunlight, close to a heat source (radiators, stoves, etc.), or in a location subject
  to vibration, excessive dust, heat, cold or moisture.

General Care

• When removing the power plug from the wall outlet, always pull directly on the plug.
  Never pull the cord.
• To keep the laser pickup clean, do not touch it, and do not forget to close the disc tray.
• Do not attempt to clean the unit with chemical solvents as this might damage the finish.
• For cleaning, only use a clean, dry cloth.
• In order to shut off the power to this product completely, unplug the power cord from the wall outlet. Be sure to
  unplug the unit if you do not intend to use it for an extended period of time.

How to Replace the Turntable Stylus (Replacement Needle # ITNP-LC1)
The stylus should last about 50 hours under normal use. However, it is recommended that the stylus
be replaced as soon as you notice a change in sound quality. Prolonged use of a worn-out stylus
may damage the record. The highest speed of 78 RPM records would wear out the stylus
more quickly.
Removing the old stylus:

1. Set a screwdriver at the tip of the stylus and push downward (A).
2. Remove the stylus by pulling it simultaneously downward
   and forward.

Installing a new stylus:

1. Hold the front tip of the stylus and insert its rear edge (B) first.
2. Push the stylus upwards (C) until the tip locks into place.

Caution:

• Do not bend the stylus.
• Do not touch the needle to avoid injury to your hand.
• Turn off the unit’s power before you replace the stylus.
• Keep out of reach of children.

Troubleshooting Guide

For further assistance with your product, call Victrola at
TOLL FREE# 1-877-ITECH-97 (1-877-483-2497).
Please note: As a result of continual improvements, the design and specifications of this product are
subject to change without notice.
Bluetooth is a registered trademark of Bluetooth SIG, Inc.
Other trademarks and trade names are those of their respective owners.
Made in China.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
WARNING: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
The device must not be co-located or operating in conjunction with any other antenna or transmitter.
To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm
from nearby persons.

IC Statement

This device complies with RSS247 of Industry Canada. Cet appareil se conforme à RSS247 de
Canada d’Industrie. This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes:
(1) le dispositif ne doit pas produire de brouillage prejudiciable, et (2) ce dispositif doit accepter tout
brouillage recu, y compris un brouillage susceptible de provoquer un fonctionnement indesirable.
The device must not be co-located or operating in conjunction with any other antenna or transmitter.
L’appareil ne doit pas être localisé ou fonctionner avec d’autres antennes ou transmetteurs.
This device complies with IC radiation exposure limits set forth for an uncontrolled environment.
Cet appareil est conforme aux limites d’exposition aux rayonnements de la IC établies pour un
incontrôlé environnement.
The device should be installed and operated with a minimum distance of 20cm between the radiator
and your body.
L’appareil doit être installé et utilisé avec une distance minimale de 20cm entre le radiateu et
votre corps.

California PROP 65 Warning

WARNING: This product can expose you to chemicals including lead, which is known to the
State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.

Victrola is a registered trademark of Innovative Technology Electronics LLC.
Innovative Technology Electronics LLC.
Limited Warranty: 90 Days Labor, One Year Parts
Innovative Technology Electronics LLC. (IT) warrants the product to be free from “Defects” in
materials under normal use for a period of “One Year” from the date of the original purchase. The
Warranty is “Not” transferable. IT agrees, within the initial “90 Day” period, to repair or replace the
product if it is determined to be defective at “No Charge”. It is further agreed that IT will cover the cost
to repair or replace damaged “Parts” only for a total period of “One Year” from the date of the original
purchase. The warranty does not cover cosmetic damage, antennas, AC cords, cabinets, headbands,
ear-pads, or damage due to line power surges, connection to improper voltage supply or settings,
misuse, mishandling, accident, acts of God or attempted repair by an unauthorized service agent.
To obtain service, the purchaser MUST present an original sales receipt / proof of purchase.
Please contact us at www.victrola.com to request an RMA (Return Material Authorization)
number to return products for service or replacement. Returns without an RMA number on the
package will be refused and returned to sender. Upon receipt of the returning item and our full
inspection (IT) may issue a replacement to customer for the same item or of one that has equivalent
value and features. To return an item, supply full name, return address, phone number, item
purchased, receipt of purchase and reason for return to obtain RMA number. All returns must be in
the original packaging or reasonable substitute to prevent damage. Customer “Must” include full
name, shipping address and telephone number inside of package. No return will be shipped back to
a PO Box or APO address. Please include your check or money order in the amount of
• USD$5.00 for items $10.00 to $39.99 (Price Paid Per Unit)
• USD$10.00 for items $40.00 to $99.99 (Price Paid Per Unit)
• USD $16.00 for items $100.00 and up (Price Paid Per Unit)
• Shipping fees are non-refundable
to be payable to Innovative Technology Electronics LLC. (for handling and return shipping charges)
(IT) will not be responsible for delays or unprocessed claims resulting from a purchaser’s failure to
provide any / all of the necessary information. Send all inquiries or RMA request via our website
www.victrola.com/pages/technical-support.
Innovative Technology Electronics LLC.
1 Channel Drive
Port Washington, NY 11050
Toll free: 1-877-483-2497
Website for support: www.victrola.com/pages/technical-support
There are no express warranties except as listed above.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE
REMEDY OF THE CUSTOMER, (IT) SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON
THIS PRODUCT EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS
PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or
limitations on how long an implied warranty lasts, so the above exclusions or limitations may not
apply to you. This warranty gives you specific legal rights and you may also have other rights, which
vary from state to state.

SAFETY INSTRUCTIONS

1. Read these instructions – All the safety and operating instructions should be read before this product is operated.
2. Keep these instructions – The safety and operating instructions should be retained for future reference.
3. Heed all warnings – All warnings on the appliance and in the operating instructions should be adhered to.
4. Follow all instructions – All operating and use instructions should be followed.
5. Do not use this apparatus near water – The appliance should not be used near water or moisture – for example, in a wet basement, near a swimming pool, or near other wet areas.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Keep at least 5 cm around the apparatus for sufficient ventilations. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug the apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. Please keep the unit in a well ventilated environment.
16. Only use attachments/accessories specified or provided by the manufacturer
17. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall not be placed on apparatus.
18. The main plug is used as disconnect device, the disconnected device shall remain readily operable.
19. This product is not intended for commercial use. Household Use Only.
20. This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth.

Warning:To reduce the risk of fire or electrical shock, do not exposed the apparatus to rain or moisture. No naked flame sources such as candles shall be placed on top of the apparatus.

Caution: Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this device. Usage of controls or adjustments or performance of procedures other than those specified herein may result in hazardous exposure.

SPECIFICATIONS

• Power Supply: AC Adaptor: 100-240, 50-60Hz DC-5V 1A
• Speaker Impedance: 4ohm, 3W
• Max Power Consumption. 6W
• Included- Turntable, Instruction Manual, Turntable Operation Sheet, 5V, 1A switching power supply, and 45 RPM adaptor

Design and specification are subject to change without notice.

Bluetooth is a registered trademark of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners

TURNTABLE LAYOUT

1. TURNTABLE PLATTER
2. TURNTABLE SHAFT
3. 45 RPM ADAPTOR
4. LIFT LEVER
5. TONE ARM CLIP
6. LINE-IN JACK
7. SPEED SELECTION SWITCH
8. FUNCTION (BT (BLUETOOTH), LINE-IN, PHONO) KNOB
9. AUTO AND MANUAL STOP SELECTION SWITCH
10. TONE ARM
11. POWER ON/OFF AND VOLUME CONTROL KNOB
12. POWER/BLUETOOTH LIGHT INDICATOR
13. STYLUS CARTRIDGE
14. HEADPHONE JACK
15. BUCKLE
16. HANDLE
17. SPEAKERS
18. RCA OUTPUT JACK
19. POWER ADAPTOR JACK

TURNTABLE OPERATION

POWER SUPPLY
Insert the adaptor plug into the DC IN jack on the rear of the unit, then connect the AC/DC adaptor (5V, 1A AC100-240V, 50-60Hz) to a AC/DC wall outlet.

BASIC OPERATION

1. Lift the BUCKLE on the front of the turntable and open the lid.
2. Turn the FUNCTION KNOB to the PHONO position. Power ON the unit by turning the VOLUME CONTROL KNOB clockwise. The red LED will light to show that the turntable is turned ON.
3. Place a record on the TURNTABLE PLATTER and select the desired speed (33 1/3 / 45 / 78) by sliding the SPEED SELECTION SWITCH according to the record. NOTE: When playing a 45 rpm record, use the included 45 RPM ADAPTOR located in the holder near the tone arm.
4. Open the TONE ARM CLIP to release the TONE ARM. Push the LIFT LEVER backwards to raise the arm. Gently move the tone arm to the desired position over the record. The turntable will begin to spin when the arm is moved toward the record. Push the lift lever forward and lower the arm slowly onto the desired position on the record to begin playing. Please Note: The record will begin to spin only when the tone arm is moved over the record if the Auto Stop is turned ON.
5. If the AUTO AND MANUAL STOP SELECTION SWITCH is turned ON, the record will stop automatically when finished. If this switch is OFF the record will NOT stop automatically when finished.
6. To select the volume level, turn the VOLUME CONTROL KNOB to adjust the volume.

HOW TO REPLACE THE TURNTABLE NEEDLE

Removing the Stylus from the Cartridge

1. Place a screwdriver at the tip of the stylus and push downward as shown in direction “A”. WARNING: when applying force to stylus, too much may damage or break the stylus.
2. Remove the stylus by pulling the stylus forward and pushing downward.

Installing the Stylus

1. Hold the tip of the stylus and insert the stylus by pressing as shown in direction “B”.
2. Push the stylus upward as in direction ‘C” until the stylus locks into the tip position.
   

BLUETOOTH OPERATION

An external device with Bluetooth Connectivity can be wirelessly connected to this turntable using the Bluetooth function.

1. Power ON the unit by turning the VOLUME CONTROL KNOB clockwise.
2. Turn the FUNCTION KNOB to the BT (Bluetooth’) position, the blue LED light will begin to flash.
3. Turn your external device’s Bluetooth Setting ON. Wait a moment, then look for the Bluetooth pairing name “Vintage Turntable”.
4. Select the Bluetooth pairing name, to connect the unit. Once connected, the blue LED light will stop flashing.
5. You are now connected to your external device via Bluetooth!
6. Rotate the VOLUME CONTROL KNOB to adjust the sound level.

AUX-IN OPERATION

An external (auxiliary) audio source (i.e. personal CD/MP3 Player/Mobile phone or computer) can be connected to this apparatus via the LINE-IN JACK.

1. Plug a detachable Aux Cable (not provided) into the LINE-IN socket on the function panel of the apparatus.
2. Turn the FUNCTION KNOB to the LINE-IN position, the LED will turn purple.
3. Plug the other end of the Aux Cable into the Headphone or Line Out socket of your External Source.
4. Power ON the unit by turning the VOLUME CONTROL KNOB clockwise.
5. Rotate the VOLUME CONTROL KNOB to adjust the sound level.

EARPHONE OPERATION

Plug the earphone jack into the earphone port on the function panel to listen to the record. The built-in speaker will stop playing once the earphones are plugged in.

NOTE: For best performance and product maintenance, unplug the turntable when not in use.

FCC STATEMENT

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CALIFORNIA PROP 65 WARNING

‘WARNING” This product contains a chemical known to the State of California to cause birth defects or other reproductive harm. For more information on these regulations and a list of chemicals, log on the following website address: http://www.oehha.ca.gov/prop65.html

WARRANTY

Victrola is a registered trademark of Innovative Technology Electronics Corp.

Innovative Technology Electronics Corp.
Limited Warranty: 90 Days Labor, One Year Parts

nnovative Technology Electronics Corp. (1’1) warrants the product to be free from “Defects” in materials under normal use for a period of “One Year from the date of the original purchase. The Warranty is “Not” transferable. IT agrees, within the initial “90 Day” period, to repair or replace the product if it is determined to be defective at “No Charge”. It is further agreed that IT will cover the cost to repair or replace damaged “Parts” only for a total period of “One Year from the date of the original purchase. The warranty does not cover cosmetic damage, antennas, AC cords, cabinets, headbands, ear-pads, or damage due to line power surges, connection to improper voltage supply or settings. misuse. mishandling, accident, acts of God or attempted repair by an unauthorized service agent.

To obtain service, the purchaser MUST present an original sales receipt / proof of purchase. Please contact us at www.ithomeproducts.com to request an RMA (Return Material Authorization) number to return products for service or replacement. Returns without an RMA number on the package will be refused and returned to sender. Upon receipt of the returning item and our full inspection (IT) may issue a replacement to customer for the same item or of one that has equivalent value and features. To return an item, supply full name, return address, phone number, item purchased, receipt of purchase and reason for return to obtain RMA number.

All returns must be in the original packaging or reasonable substitute to prevent damage. Customer “Must” include full name, shipping address and telephone number inside of package. No return will be shipped back to a PO Box or APO address.

Please include your check or money order in the amount of:

• USD $5.00 for items $10.00 to $39.99 (Price Paid Per Unit)
• USD $10.00 for items $40.00 to $99.99. (Price Paid Per Unit)
• USD $16.00, for items $100.00 and up. (Price Paid Per Unit)
• Shipping fees are non-refundable

to be payable to Innovative Technology Electronics Corp. (for handling and return shipping charges) (IT) will not be responsible for delays or unprocessed claims resulting from a purchaser’s failure to provide any / all of the necessary information. Send all inquiries or RMA request via our website www.ithomeproducts.com/support.

Innovative Technology Electronics Corp. 1 Channel Drive Port Washington, NY 11050 Toll free: 1-877-483-2497 Website for support: www.ithomeproducts.com/support

There are no express warranties except as listed above.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CUSTOMER, (IT) SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.

Victrola Nostalgic 6-in-1 Bluetooth Record Player & Multimedia Center

Specifications

• POWER REQUIREMENTS: AC 100-240V~50/60Hz
• POWER CONSUMPTION: 30W
• DIMENSIONS (W X H X D): 460 x 255 x 340mm | 18 x 10 x 13.4in (approx.)
• WEIGHT: 7 kg. | 16 lbs. (approx.)
• AMPLIFIER: OUTPUT POWER: 5 W + 5 W,
• FREQUENCY RESPONSE: 60 to 20,000 Hz
• SPEAKER SYSTEM: TYPE: 2-way
• IMPEDANCE: 8 ohms
• OUTPUT POWER: Max. 6W
• FM RADIO: RANGE: 88 to 108 MHz
• CD PLAYER: FREQUENCY RESPONSE: 60 to 20, 000 Hz +/-4 dB
• SIGNAL-TO-NOISE RATIO: 55 dB (IEC-A)
• CASSETTE PLAYER: TRACK SYSTEM: 4 Track, 2 channel stereo
• TAPE SPEED: 4.8 cm/sec
• WOW AND FLUTTER: 0.4% (WRMS)
• FREQUENCY RESPONSE: 125 to 6300 Hz +/-6 dB
• RECORD PLAYER: MOTOR: DC servo motor
• DRIVE SYSTEM: Belt Drive
• SPEEDS: 33-1/3rpm, 45 rpm and 78 rpm
• S/N RATIO: More than 50 dB
• CARTRIDGE TYPE: Ceramic Stereo
• CARTRIDGE STYLUS: ITRRS-300
• BLUETOOTH VERSION: Bluetooth V2.1
• BLUETOOTH PROFILES: A2DP, AVRCP
• BLUETOOTH FREQUENCY RANGE: 2.402GHz-2.480GHz
• OPERATING DISTANCE: 10 meters (33 ft.)

Introduction

Listen to vinyl records, CDs, cassette tapes, AM/FM radio, or stream music from your smartphone via Bluetooth or a 3.5 mm Aux/headphone connector. A stereo system or additional equipment is not required. In only a few minutes, you’ll have it up and running. This record player is a wonderful value, with its retro appearance and the convenience of current technology. It’s perfect for beginners and vintage fans alike. It is a belt-driven turntable with a three-speed.

This record player has three speeds (33 1/3, 45, and 78 rpm) and has upgraded premium sound quality with minimal vibrations. It’s ideal for your living room, bedroom, or office, and vinyl fans will enjoy it. Extend the sound by using the RCA Line outputs to connect external speakers or an amplifier (cable included). Plug your headphones into the headphone jack for private listening.

ACCESSORIES INCLUDED

• RCA LINE OUT CABLE
• INSTRUCTION MANUAL
• WARRANTY (BACK OF MANUAL)
• 45 RPM ADAPTER

PRODUCT OVERVIEW

FRONT VIEW

1. POWER: Push to turn the unit ON or OFF.
2. “PHONO, CD, AUX, FM/” SELECTION KNOB Rotate to select your desired function.
3. “FM” SLIDE SWITCH Slide to select either FM or Bluetooth.
4. 5mm AUX-IN JACK Connects your external source to the AUX IN jack.
5. PLAY INDICATOR Illuminates when CD is playing.
6. ST/BT INDICATOR Blue light flashes when the unit is waiting for pairing. Blue light stays lit when the external device is connected to the unit. A red light illuminates when the station is received in stereo playing mode.
7. PROGRAM INDICATOR Illuminates when the program playback is set.
8. REPEAT INDICATOR Red light stays lit when all tracks repeat. Red light flashes when a single track is repeating.
   (Note: This indicator only works in CD mode.)
9. LED DISPLAY
10. TUNING DIAL POINTER
11. STEREO SPEAKERS
12. STOP: Press to stop playback or cancel the program setting.
13. PLAY/PAUSE: Press to start playback, press again to pause.
    (Note: This button only works in CD, Bluetooth mode.)
14. OPEN/CLOSE
15. DISC TRAY
    In CD mode, use to open and close the disc tray.
16. “VOLUME” KNOB Turn to adjust the volume.
17. & 18. NEXT/PREVIOUS TRACK
    & OFF/REWIND
    In CD Mode, press once to skip to the next/previous track. Press and hold to fast forward/rewind.
    (Note: This button will not work in PHONO, FM, or AUX mode)
18. “PROGRAM” Press to set the program playback.
    (Note: This indicator only works in CD mode.)
19. “REPEAT” Press to select the repeat mode.
    (Note: This indicator only works in CD mode.)
20. RADIO TUNER KNOB In FM mode, turn to tune in a station.
21. 5mm EARPHONE JACK
    Accepts headphone/earphone plugs

RIGHT SIDE VIEW

23. CASSETTE FF & EJECT Press halfway to fast forward, press all the way to the end, and eject the tape.

REARVIEW

24. FM WIRE ANTENNA
    While tuned to a station in FM mode, extend the wire and reposition to adjust for the best reception.
25. LINE OUT JACKS
    For amplifier device with RCA auxiliary input sockets, insert the white and red plugs on the RCA cable into the unit. Insert the opposite end into the amplifier device. Be sure to connect the white plug to the white jack and the red plug to the red jack.
26. AC POWER CORD
    Connect the AC plugs into a wall outlet. It is strongly recommended that this product should be operated only from the type of power source indicated on the marking label.

PARTS OF THE TURNTABLE

• TURNTABLE
• SAFETY SCREW (FOR TRANSPORT) Before using the unit, turn the screw clockwise using a coin or screwdriver.

Important
When you transport the unit, turn the screw counterclockwise to secure the turntable.

• SPEED SELECTOR.
• TONEARM HOLDER.
• TONEARM. Before use, completely loosen the fixed rope on the tonearm and lift the tonearm up.
• STYLUS
• 45 RPM ADAPTOR.

SETUP / BASIC OPERATION

SETUP

1. Remove the white protective needle cover by gently pulling towards the front of the unit.
   
2. Remove any packaging materials from the unit.
3. Connect the AC power cord to a wall outlet

NOTE:

-It is strongly recommended that this product should be operated only from the type of power source indicated on the marking label.

-To prevent interference, avoid bundling audio signal cables together with the AC power cord.

BASIC OPERATION

1. Push the POWER button to turn the unit on.
2. Select the source by turning the selection knob (PHONO/AUX/CD/FM/BT).
3. Rotate the VOLUME knob to adjust to the desired sound level.

LISTENING THROUGH RCA LINE OUT

For amplifier device listening, first, reduce the volume level to a minimum. Insert the white and red plugs on the RCA cable into the unit, then insert the opposite end into the amplifier device. Be sure to connect the white plug to the white jack and the red plug to the red jack.

LISTENING THROUGH EARPHONES/HEADPHONES (NOT INCLUDED)

• For private listening, first, reduce the volume level to minimum.
• Insert your headphones’ plug into the 3.5mm jack, then adjust the volume up by turning the VOLUME knob.

NOTE
 The speakers will automatically be deactivated while headphones are plugged in.

CONDENSATION WARNING

When the unit is moved from a cold or warm place or is used following a sudden temperature change, there is the danger that water vapor in the air may condense on the unit, preventing proper operation. In such cases, leave the unit for 1-2 hours after plugging it into an AC outlet to allow it to stabilize at the temperature of its surroundings.

LISTENING TO A VINYL RECORD

1. Select the “PHONO” function.
2. Gently open the top cover.

NOTE
Be careful not to pinch your fingers when opening/closing the top cover.

3. Place a vinyl record on the turntable. When playing a 45 RPM record, use the included adaptor.

4. Select the appropriate speed.
5. Remove the tone arm-rest holder to release the tonearm
   
6. Move the tonearm gently to the edge of the record (or the starting point of a track).

The turntable will begin to turn.

7. When the record reaches its end, the tonearm will stop at the center of the record and you must lift and return the tonearm to the tonearm rest manually. Lock the tone arm-rest holder to protect the tonearm.

IMPORTANT

• Closing the top cover will help prevent dust from settling on the turntable.
• Always relock the tonearm clip before transporting the unit.
• Do not place anything on top of the turntable cover, especially while playing a record.

LISTENING TO A CD

1. Select the “CD” function.

(Note: When no disc is set, “no” will appear on the display.)

2. Press the OPEN/CLOSE button

(Note: This button only works in CD mode.)

3. Place a disc on the tray with the printed label face up.
   
4. Press the OPEN/CLOSE button to close the tray.
5. Press the PLAY/PAUSE button to begin playback.

(NOTE: The CD playback will start automatically.)

6. To temporarily pause playback, press the PLAY/PAUSE button. Press again to resume.
7. To skip tracks forward or backward, press the corresponding skip button. Pressing once will restart the current track. Pressing twice in succession will return to the beginning of the previous track.
8. To fast forward / rewind within a track, press and hold down the corresponding skip button until the desired position is reached.
9. To stop playback, press the STOP button

IMPORTANT

• Never place more than one disc on the tray.
• The disc must be placed in the center of the disc tray. An incorrectly loaded disc can permanently damage the tray door mechanism.
• Do not push the CD tray – always use the OPEN/CLOSE button.
• It takes a moment for the unit to load a disc, during which all buttons will be temporarily deactivated.

REPEAT PLAYBACK
Each time the REPEAT button is pressed, the repeat mode will cycle through the following options:

REPEAT 1(REPEAT ONE TRACK)
The repeat indicator will flash and the current track will be played repeatedly. If you press the forward or rewind button to select another track, the track you select will be played repeatedly.

REPEAT ALL (REPEAT THE ENTIRE CD)
The repeat indicator will stay lit and the entire CD will be played repeatedly.

NOTES

• Repeat playback works with CD discs only.

PROGRAMMED PLAYBACK

Up to 20 tracks can be programmed to play in the desired order.

NOTES

• Programmed playback works with CD discs only.

1. Select “CD” mode, then load a CD.
2. While the CD is stopped, press the PROGRAM button.
3. “PROGRAM” indicator lights up and “01” blinks on the display.
4. Press forward or rewind to select a tracking number.
5. Press the PROGRAM button again to set the next program track, “02” appears and blinks… Repeat steps 4 thru 5 to program the additional tracks.
6. When the selection of track numbers has been finished, press the PLAY button ( ) to start the program playback.

(NOTE: when all 20 program tracks are set, you press the PROGRAM button and “FU” will appears on the display)

7. To cancel the program mode, press the STOP till the program indicator won’t light.

TO CHECK THE PROGRAMMED ORDER

• In the stop mode, press forward or rewind repeatedly to show the track numbers which have been programmed.

TO ADD A TRACK TO THE END OF THE PROGRAMMED ORDER:

• In the stop mode, press the PROGRAM button.
• Select a tracking number by pressing forward or rewind, then press the PROGRAM button. The current track will be added to the end of the program.

LISTENING TO THE FM RADIO

1. Select “FM/” mode.
2. Slide the slide switch on “FM”.
3. Tune to the desired station using the Radio Tuner Knob.

NOTE
In FM Mode, the “ST/BT” indicator lights up red when tuning in the stereo reception station.

ADJUSTING FOR THE BEST RECEPTION

FM BROADCAST
 Extend and reposition the FM antenna.

LISTENING TO AN EXTERNAL AUDIO DEVICE (AUX MODE)

• In AUX (auxiliary) mode, this unit can play audio from an external audio source (iPod, MP3 Player, Portable CD Player, etc.)
• There is an AUX IN jack on the front side of the unit. When connecting a device that has a headphone jack, use a cable with a 3.5mm plug on both ends with the front AUX IN jack.

1. Plug one end of the AUX IN cable (not included) into the AUX IN jack.
2. Plug the other end of the cable into the headphone jack of the external audio source.

NOTE
All operations are only available on your external device.

IMPORTANT
 If the front AUX IN and rear RCA LINE OUT are connected at the same time, only the front AUX IN will be active.

LISTENING TO AN EXTERNAL AUDIO DEVICE (BLUETOOTH MODE)

In BT (Bluetooth) mode, this unit can play music from external devices that have a built-in Bluetooth feature.

GETTING CONNECTED USING BLUETOOTH

1. Select “FM/” mode.
2. Slide the slide switch on “Bluetooth” and the ST/BT indicator will flash blue.
3. Turn ON the Bluetooth function on your external device.

NOTE
 The effective distance between your external device and this apparatus is 10 meters (33ft).

4. Wait for “Wooden Music Center” to appear on the paired devices list of your external device and press “Wooden Music Center”.

IN SOME INSTANCES
 a window will ask you a password. Fill in “0000” then press “OK” on your external device.

5. A few seconds later your Bluetooth connection is successful and the blue indicator stays lit.
6. Press the PLAY/PAUSE button to begin playback.
7. To temporarily pause playback, press the PLAY/PAUSE button. Press again to resume.
8. To skip to the previous or next tracks, press the corresponding skip button to listen.

NOTE
Stop, fast forward / rewind is only available on your external device.

LISTENING TO A CASSETTE TAPE

1. Load an audio cassette tape into the unit (located on the left side of the unit). Playback will automatically begin.
2. Press the button halfway to Fast Forward the tape. Press the button lightly and playback will resume.
3. Press the button completely down to end playback and eject the tape.

NOTE
When loading in a cassette tape, the SELECTION KNOB function will be temporarily overridden until the cassette tape is ejected.

MAINTENANCE / PROPER HANDLING

COMPACT DISC HANDLING

• Always place the disc on the disc tray with the label side facing upward (compact discs can be played/recorded only on one side)
• To remove a disc from its storage case, press down on the center of the case and lift the disc
• upward, holding it carefully by its edges.
• To clean a disc, wipe the surface from the center hole outward towards the outer edge with a soft, dry cloth.
• Never use such chemicals as record spray, antistatic sprays or fluid, benzine or thinner to clean discs; they will irreparably damage the disc’s plastic surface.
• Discs should be returned to their cases after use to protect from dust and scratches.
• Do not expose discs to direct sunlight, high humidity, or high temperature for extended periods of time.
• Printable CD-R and CD-RW discs are not recommended, as the label side may become sticky and damage the unit.
• Use a soft oil-based felt-tipped pen to write information on the label side. Never use a ball-point or hard-tipped pen, as doing so may damage the recorded side.
• Do not use irregularly shaped CDs (octagonal, heart-shaped, business card size, etc.), as they will damage the unit.
• Read all precautions supplied with any CD-R or CD-RW disc
• Never handle a disc with dirty fingers.
• Never insert a disc that has a crack on the surface.

HANDLING VINYL RECORDS

• Do not touch the record’s grooves. Only handle records by the edges or the label with clean hands. Touching the record surface will cause your record’s quality to deteriorate.
• To clean a record, use a soft anti-static cloth to gently wipe the record surface.
• Keep records in their protective sleeves when not in use.
• Always store records upright on their edges
• Avoid placing records in direct sunlight, close to a heat source (radiators, stoves, etc.), or in a location subject to vibration, excessive dust, heat, cold or moisture.

GENERAL CARE

• When removing the power plug from the wall outlet, always pull directly on the plug. Never pull the cord.
• To keep the laser pickup clean, do not touch it, and do not forget to close the disc tray.
• Do not attempt to clean the unit with chemical solvents as this might damage the finish.
• For cleaning, only use a clean, dry cloth.
• In order to shut off the power to this product completely, unplug the power cord from the wall outlet. Be sure to unplug the unit if you do not intend to use it for an extended period of time.

HOW TO REPLACE THE TURNTABLE STYLUS

The stylus should last about 50 hours under normal use. However, it is recommended that the stylus be replaced as soon as you notice a change in sound quality. Prolonged use of a worn-out stylus may damage the record. The highest speed of 78 RPM records would wear out the stylus more quickly.

REMOVING THE OLD STYLUS

1. Set a screwdriver at the tip of the stylus and push downward (A).
2. Remove the stylus by pulling it simultaneously downward and forward.

INSTALLING A NEW STYLUS

1. Hold the front tip of the stylus and insert its rear edge (B) first.
2. Push the stylus upwards (C) until the tip locks into place.

CAUTION

• Do not bend the stylus.
• Do not touch the needle to avoid injuring your hand.
• Turn off the unit’s power before you replace the stylus.
• Keep out of reach of children.

Fequently Asked Questions

• How good are Victrola turntables?
  The Victrola Vintage 3-Speed Bluetooth Suitcase Turntable with Speakers isn’t the greatest record player with speakers on the market, but it’s ideal for the audiophile on a budget looking for the best possible listening experience at a reasonable price.
• Is the sound quality on the Victrola good?
  The Victrola offered a considerably flatter response than the Crosley, but neither came close to the quality of the speakers mentioned in our best bookshelf speakers guide. The Victrola had a very flat response throughout an audio range of roughly 80 Hz to 15 kHz, but the Crosley had a response of about 180 Hz to 5.8 kHz.
• Is it possible to connect your smartphone to a Victrola record player?
  Bluetooth speakers are capable of connecting to devices other than your record player. Your phone’s Bluetooth capability can also be used to connect to your speakers. The speakers are set up in the same way, and the Bluetooth option may be found in your phone’s settings.
• Are Victrola record players appropriate for novices?
  More than 33,000 five-star ratings have been left for this beginner-friendly Victrola record player. (And, despite the fact that it’s called a turntable, the built-in speakers make it a record player.)
• What’s the deal with my Victrola record player being so quiet?
  By their very nature, record players are silent. They generate a very weak electrical signal that must be amplified twice. A preamp (internal or external) amplifies it first, bringing it up to the same line level as a CD player. Then it needs to be boosted again so that it can be heard through your speakers.
• Is there a speaker on a Victrola record player?
  Are you going to the beach or having a family barbecue? Whether you use the built-in speaker or connect it to an external speaker, our portable turntable is the right combination of functionality, vintage/retro appearance, and sound quality.
• What’s the best way to hook up my Victrola to a Bluetooth speaker?
  By connecting the RCA input side of your cable to the turntable and the 3 pins on the turntable, you may connect your turntable to your Bluetooth home speakers. Your Bluetooth speaker should be 5mm connected to the cable’s side.
• On a Victrola record player, how does Bluetooth work?
  To send the signal from your turntable through Bluetooth, all you need is a phono preamplifier and a Bluetooth transmitter. If your preamplifier has an external phono output, connect the transmitter to it. You can pair your turntable with a Bluetooth-enabled speaker or amplifier once it has been connected.
• Is it possible to connect external speakers to the Victrola?
  Connecting powered speakers to a Victrola with an RCA signal connection is the easiest and most dependable method of connecting external speakers to a Victrola. The Victrola’s RCA connectors produce a line-level analogue music signal that may be played on any powered speaker.
• What is the lifespan of a Victrola needle?
  Every stylus, no matter how sturdy, has a limited lifespan due to its frequent use. The majority of experts advise replacing it after 1,000 hours of use.

VICTROLA VTA-71 Brighton Bluetooth Record Player

• This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
• Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts insides. Refer servicing to qualified personnel.
• The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance.
  CAUTION: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
  WARNING:To prevent electric shock, do not use this (polarized) plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.

SAFETY INSTRUCTIONS

1.  Read these instructions – All the safety and operating instructions should be read before this product is operated.
2.  Keep these instructions – The safety and operating instructions should be retained for future reference.
3.  Heed all warnings – All warnings on the appliance and in the operating instructions should be adhered to.
4.  Follow all instructions – All operating and use instructions should be followed.
5.  Do not use this apparatus near water – The appliance should not be used near water or moisture – for example, in a wet basement or near a swimming pool, and the like.
6.  Clean only with dry cloth.
7.  Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8.  Do not install near any heat sources such as radiations, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9.  Do not defeat the safety purpose of the polarized or grounding plug. A polarized Safety Instructionsplug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10.  Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus.
11.  Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13.  Unplug the apparatus during lighting storms or when unused for long periods of time.
14.  Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
16. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall not be placed on apparatus.
17.  Use the equipment in a moderate climate.

ACCESSORIES INCLUDED

• INSTRUCTION MANUAL
• WARRANTY (BACK OF MANUAL)
• POWER ADAPTOR

PRODUCT OVERVIEW

Front View

Rear View 

Part of the Turntable

1.  POWER: Press to turn the unit ON or OFF.
2. BT OUT: Press to activate the Bluetooth output function.
3. PLAY/PAUSE  Press to start playback, press again to pause. Long press the button for 3 seconds to disconnect the Bluetooth pairing.(NOTE: This button only works in Bluetooth mode.)
4. PREVIOUS Skip to the previous track or station.
5. NEXT  Skip to the next track or station.
6.  Display Screen
7.  3.5mm EARPHONE JACK: Accepts headphone/earphone plugs.
8.  BT/PHONO/FM KNOB: Turn to select BT/PHONO mode.
9.  VOLUME KNOB: Turn to adjust volume.
10. LINE OUT jacks For amplifier device with RCA auxiliary input sockets, insert the white and red plugs on the RCA cable into the unit. Insert the opposite end into the amplifier device. Be sure to connect the white plug to the white jack and the red plug to the red jack.
11.  DC Input Jack Connect the power adapter to the jack to power on the unit.
12.  Turntable
13.  45 RPM adapter
14.  Tone Arm holder
15. Cue Lever: Before use, gently push the Tone Arm holder to the right to release the TONE ARM.
16. AUTO STOP ON/OFF SWITCH: Switch “ON”, the turntable will stop automatically when finish playing. Switch “OFF”, the turntable will keep turning when finished playing.
17. Speed Selector
18.  Tone Arm
19.  STYLUS

SETUP/BASIC OPERATION

Setup

1.  Remove white protective needle cover by gently pulling towards front of unit.
2.  Remove any packaging materials from the unit.
3. Connect the power adapter to the DC Input jack to power on the unit.

Note: It is strongly recommended that this product should be operatedonly from the type of power source indicated on the marking label.

Basic Operation

1.  Press the POWER button to turn the unit on.
2.  Select mode by turning the BT/PHONO KNOB.
3.  Rotate the VOLUME KNOB to adjust to the desired sound level.

Listening through RCA LINE OUT
For amplifier device listening, first reduce the volume level to minimum. Insert the white and red plugs on the RCA cable into the unit, then insert the opposite end into the amplifier device. Be sure to connect the white plug to the white jack and the red plug to the red jack.

Listening through Earphones/Headphones (not included)
For private listening, first reduce the volume level to minimum. Insert your headphones’ plug into the 3.5mm jack, then adjust the volume up by turning the VOLUME KNOB.
Note: The speakers will automatically be deactivated while headphones are plugged in.
CONDENSATION WARNING:
When the unit is moved from a cold or warm place, or is used following a sudden temperature change, there is the danger that water vapor in the air may condense on the unit, preventing proper operation. In such cases, leave the unit for 1-2 hours after plugging it into an AC outlet to allow it to stabilize at the temperature of its surroundings.

VINYL RECORD OPERATION

1.  Turn the unit ON by pressing the POWER button.
2.  Turn the BT/PHONO KNOB to enter the PHONO mode.
3.  Gently open the dust cover.
4.  Put the record on the turntable. Select the speed. When playing a 45 RPM record, use the included 45 adaptor.
5. Gently push the Tone Arm holder to the right to release the TONE ARM.
6. Raise the Cue Lever to lift the TONE ARM off the tone arm support.
7. Move the TONE ARM gently to the edge of the record (or the starting point of the track). The turntable will begin to turn.
8.  Gently lower the TONE ARM by slowly releasing the CUE LEVER. You can lower the TONE ARM manually if the CUE LEVER has not been raised.
9. Turn the VOLUME KNOB to adjust the volume.
10. When playback has finished, slightly lift the tone arm using the CUE LEVER and return it to the TONE ARM holder.

BLUETOOTH OPERATION

An external device with Bluetooth Connectivity can be wirelessly connected to this turntable using the Bluetooth Function.

GETTING CONNECTED USING BLUETOOTH

1. Turn the BT/PHONO KNOB to select BT mode. The “bt” will flash on the Display Screen.
2.  Turn your external devices’ Bluetooth Setting ON. Wait a moment, then look for the Bluetooth Pairing name “Victrola Brighton”
   NOTE: The effective distance between your external device and this unit is 10 meters (33ft).
3.  Select the Bluetooth pairing name, to connect the unit. Once connected the “bt” on the Display Screen will stop flashing.
4.  Select the music media files on your external device PLAY/PAUSE button ( ) to begin playback.
5. To temporarily pause playback, press the PLAY/PAUSE button ( ) when playback. Press again to resume.
6.  To skip to the previous or the next tracks, press the PREVIOUS/NEXT button ( or ) to listen.

BLUETOOTH-OUT OPERATION

The product supports Bluetooth wireless connection (BT-OUT). It can be connected with external Bluetooth-compatible headphones (not included) and Bluetooth speakers (not included) .

1.  When playing your vinyl record, press the BT OUT button.
2.  The “ ” icon flashes on the Display Screen.
3.  Turn ON your external Bluetooth receiver device (such as Bluetooth headphones and Bluetooth Speakers) and set to pairing mode.
4.  Wait for a few seconds, they will make connection to each other automatically.
5.  The “ ” icon stops flashing once successful paired.
6.  Control the playback from your BT speaker.(You can only adjust the volume from your external Bluetooth Device.)
   •  Place the Bluetooth device within 1m (3.3′) of the product to perform pairing correctly.
   • The product stays in the pairing mode for about 30 seconds. If pairing is not properly completed, follow the above steps again from the beginning after turning all devices OFF.
   •  “BT OUT” is only compatible with vinyl record playback.

MAINTENANCE/PROPER HANDLING

Handling Vinyl Records

• Do not touch the record’s grooves. Only handle records by the edges or the label with clean hands. Touching the record surface will cause your record’s quality to deteriorate.
• To clean a record, use a soft anti-static cloth to gently wipe the record surface.
• Keep records in their protective sleeves when not in use.
• Always store records upright on their edges.
• Avoid placing records in direct sunlight, close to a heat source (radiators, stoves, etc.), or in a location subject to vibration, excessive dust, heat, cold or moisture.

HOW TO REPLACE THE TURNTABLE STYLUS (Replacement Stylus # VND-08)

Removing the Stylus from the Cartridge

1.  Using your fingers, hold at point “A” and push down point “B”
   WARNING: When applying force to stylus, too much may damage or break the stylus.
2.  Continue to push down until the stylus separates from the front of the cartridge.
3.  Remove the rear of the stylus carefully from the cartridge.

Installing the Stylus
 Follow the previous steps but in reverse.
Caution:

• Do not remove or bend the stylus needle.
• Do not touch the needle to avoid injury to your hand.
• Turn off the unit’s power before you replace the stylus.
• Keep out of reach of children.

Please note: The stylus should last about 50 hours under normal use. It is recommended that the stylus be replaced as soon as you notice a change in sound quality

TROUBLESHOOTING GUIDE

Please note: As a result of continual improvements, the design and specifications of this product are subject to change without notice.
Bluetooth is a registered trademark of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners.

SPECIFICATIONS

GENERAL
Power adapter ———————–DC 5V/1A
Power Consumption —————5W
Power Output ————————2 × 2W
Size————————————-12.7″ (322mm) W × 12.3″ (312mm) D × 5.2″ (131mm) H Weight ———————————4.5 lbs (2kg)

RECORD PLAYER
Speeds ——————————–33-1/3 RPM, 45 RPM and 78 RPM

BLUETOOTH
Bluetooth Version——————-V4.0
Bluetooth Profiles ——————-A2DP, AVRCP
Bluetooth Frequency range ——2.402GHz-2.480GHz
Operating Distance—————–10 meters (33 ft.)

FCC STATEMENT

1.  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
   1.  This device may not cause harmful interference, and
   2.  This device must accept any interference received, including interference that may cause undesired operation.
2.  Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CALIFORNIA PROP 65 WARNING

WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

IC WARNING

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference; and
2.  This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

WARRANTY

Victrola is a registered trademark of Innovative Technology Electronics LLC.
Innovative Technology Electronics LLC. (IT) warrants the product to be free from
“Defects” in materials under normal use for a period of “One Year” from the date of the original purchase. The Warranty is “Not” transferable. IT agrees, within the initial “One Year” period, to replace the product if it is determined to be defective at “No Charge” or offer a merchandise credit if proof of purchase is provided or if the original product is no longer in stock. It is further agreed that IT will cover the cost to repair or replace damaged “Parts” only for a total period of “One Year” from the date of the original purchase. The warranty does not cover cosmetic damage, antennas, AC cords, cabinets, headbands, ear-pads, or damage due to line power surges, connection to an improper voltage supply or setting, misuse, mishandling, accident, acts of God or attempted repair by an unauthorized service agent.
Repair or Replacement as provided under this warranty is the exclusive remedy of the customer, (IT) shall not be liable for any incidental or consequential damages for breach of any implied warranty on this product except to the extent prohibited by applicable law. Any implied warranty of merchant-ability or fitness for a particular purpose on this product is limited in duration to the duration of this warranty.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.
Contact
Website: www.victrola.com/support
Phone: (877) 483-2497
(Monday – Friday, 10am – 6pm, EST)