YAMAY Smart Watch Instructions

Please read the instructions carefully and keep it safe. 

Bind Watch

1.Download and install App
You can set up the watch through the “VeryFitPro” app for iOS Android devices. The steps are shown as follows:
Notes: The hardware platform of the equipment system shall meet requirements.I. Bind Watch

Correct operation: Scan the QRcode below or download VeryFitPro APP through the mobile APP store to pair with the watch.

http://www.youduoyun.net/qrcode.html

The wrong operation: Pair the watch directly with the  Bluetooth in your mobile phone’s settings.

2. Bind process

1. Turn on the Bluetooth and GPS on your mobile phone
   
2. Bind Device
3. Select product model: ID205U
4. Click “Ok” to complete binding.

Notes:

①.During the binding process, VeryFitPro will prompt you to enable GPS  and Bluetooth, and authorize VeryFitPro to get access to the GPS on your mobile phone.
②. Apple phones need to click “pair”, the watch has a variety of message reminders.

3.Synchronous data
In daily wear, the watch can detect all kinds of product data. The user needs to connect the watch with Bluetooth on the APP before synchronous operation. The detailed  operations are shown as follows:

Open the mobile APP> swipe down the page> sync prompt appears
Notes!
Please synchronize the data at least once within 7 days to avoid data loss at the watch end.

Instruction for Use

1. Charging schematic
   Buckle the watch into the charger seat as shown in the picture. It needs to be charged to activate the watch when it is started for the first time. Make sure the metal contacts of the watch and of the Charging dock match well, then the watch can be charged properly.
2. Wear/install

Wear the wristband one finger away from the wrist bone and adjust the tightness of the wristband to a comfortable position.	Flip the switch and take out the wristband

①.Wear
Wear the wristband one finger away from the wrist bone and adjust the tightness of the wristband to a comfortable position.
②.Replace the strap
Switch
Flip the switch and take out the wristband
Tip: Wearing too loosely may affect the accuracy of heart rate data.

Operating Instructions

1. Definition of key function
2. Watch dial switch
   Replacing the dial interface will appear after long-press the dial.
3. Main interface operation Swipe the screen to enter differently interfaces (interactive interface tile diagram)

①. Notice: Display notification message content.
②.Status：

Heart rate Detection	Wrist sense	Do not disturb mode	Looking for a mobile phone.

③.Data bar:

④.Function list interface：See below for Function Introduction。

4.Dial data view (default dial)。

Long press the screen to switch different data

Function Introduction

1. Icon function introduction

Enter the window of the sports, and choose different sports modes.  Change the sports mode on the APP	Perform a heart rate test to check your heart rate data for the day.	Help you regulate your breathing and relax your mood.	View, turn off, or urn on the alarm clock. You need to add an alarm clock on the mobile APP.

Control music play on your mobile phone  (watch cannot store music)	Have the timing and countdown function.	Record recent sports.

①.Enter the window of the sports, and choose different sports modes.
Change the sports mode on the APP

1. Start sports
   Click the sports icon > select the sports type > enter the sports countdown automatically
2. During sports
   Pause sports: short press the right key
   Restore sports: short press the right key
3. End sports
   End sports: long-press the right key> select the end button on the screen

②.Perform a heart rate test to check your heart rate data for the day.

③.Help you regulate your breathing and relax your mood.
④.View, turn off or turn on the alarm clock. You need to add an z alarm clock on the mobile APP.

⑤.Control music play on your mobile phone (watch cannot store music)

⑥.Have the timing and countdown function.
⑦.Record recent sports
⑧. settings

2. Sleep detection: The watch automatically detects sleep all day, please wear a good watch when using it;
Notes: For more functions and operations, please check the VeryFitPro software of the mobile phone.

Product Parameters

Battery life: Actual battery life and charging time will vary depending on usage and environment, etc.
Waterproof: Not suitable for diving, swimming in the sea, or sauna. But suitable for swimming in swimming pool or in the shower (cold water) and shallow beach.

Cleaning and Maintenance

It is recommended to wear and maintain according to the
following three points:

1. Keep the product clean;
2. Keep the product dry;
3. Do not wear it too tight.

Do not use household cleaners to clean the watch, but use soap-free detergent.
It is recommended to use alcohol to scrub stains that are not easy to remove.

Frequently Asked Questions

1. Mobile APP search for the watch failed
   (1)It is recommended to update VeryFitPlus to the latest version.
   (2)It is recommended to close all programs, restart the Bluetooth, and then connect
   (3)Confirm whether the mobile phone system meets Android 4.4 or IOS 8.0 or above.
2. The watch received no alerts, text messages or phone calls
   (1)You need to turn on the smart reminder function and the call reminder switch in the APP and synchronize to the watch.
   (2)The iPhone needs to be paired with the watch via Bluetooth.
   (Please check the column of “Synchronous Data” for details)
   (3)You need to keep your watch connected to Bluetooth.
3. Bluetooth is often disconnected
   (1)If the distance between the watch and the mobile phone is too far, the connection effect of more than 7m Bluetooth is obviously weakened.
   (2)Whether there is a shield between the watch and the mobile phone, the human body, wearing metal jewelry, etc., will interfere with the Bluetooth connection signal.
   (3)Whether the Bluetooth function of the mobile phone is abnormal.
4. About data backup
   The data of the watch is synchronized at least once every 7 days to the mobile phone (the watch end only keeps the data of the last 7 days).
5. How to restart and restore factory settings
   Shutdown operation: Watch > set > shutdown/right-key restart Restore factory settings: connect watch to APP > open APP > device model > more settings
6. Do I need to keep my Bluetooth on when I wear my watch?
   (1)For the three functions, i.e. counting steps, sleeping, and alarm clock, you do not need to connect the watch to the mobile phone all the time. If you only need to wear a  watch when you exercise, you can connect the watch and your mobile phone to view the data synchronously after the exercise.
   (2)For the functions of call alert, message alert, find the phone, you need to turn on the mobile phone’s Bluetooth, and maintain the connection with the mobile phone.
   More detailed questions can be answered with help and feedback in the APP.
   Operation steps:VeryFitPro > > help and feedback Matters Needing Attention
   ①.Watch data needs to be kept once every 7 days to avoid data loss.
   ②.The watch has no waterproof effect on seawater, acidic and alkaline solutions, chemical reagents and other corrosive liquids. The damage or defects caused by misuse or improper use are not covered by the warranty.
   ③.Sports mode supports up to 6 hours of exercise at a time.
   ④.The watch has a waterproof level of IP68 and supports a cold water shower, swimming, but not diving.
   ⑤.Avoid wearing the watch too tight in daily use. Please keep the parts of the watch touching the skin dry.
   ⑥.When your heart rate is measured, keep your arm still during the test.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion. Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas. battery subjected to the extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

FAQS

Is Yamay smartwatch accurate?

Accurate Fitness Tracker Watch – YAMAY watch will accurately track your all-day steps,calories consumption,distance traveled,heart rate.It also supports extra 7 sports modes to help you track your other exercise patterns,and will connect to smartphone’s GPS to draw the route map in the related app.

Does Yamay smart watch take blood pressure?

This watch can track your heart rate, blood pressure and blood oxygen in a very convenient way, which making it to be a very good health assistant for you.

Can you answer calls on Yamay smart watch?

The device has a speaker and microphone that allow you to answer calls made to your smartphone.

Are Yamay watches any good?

The Yamay Fitness Tracker Watch has great performance. It comes with many excellent features like a heart rate monitor, sleep monitor, and stopwatch. It can also count your steps, calories, speed, and distance if you want to treat it as a fitness tracker or hiking watch

Which Yamay Watch tracks blood pressure?

[Heart Rate & Blood Pressure & Blood Oxygen Monitor]- YAMAY 023 can accurately monitor this three body’s most critical indicator of health. You can read them real-time directly on the watch.

Are blood pressure watches any good?

Blood pressure monitor watches may provide accurate readings, although this hasn’t been proven in large-scale studies. To get the most accurate, consistent results, it may make sense to choose a watch designed specifically for this purpose, rather than a fitness tracker that includes this feature.

Is there a smart watch that monitors blood pressure?

It has an all-day heart rate and blood pressure monitor, too, so you can review your health data and see your progress over time. Extra features include a sedentary alarm, sleep quality assessment, and women’s health tracking.

How accurate is a smart watch blood pressure?

Is smartwatch blood pressure accurate? The Bodimetrics performance monitoring and the reference had an average difference of 5.3 (4.7) mm Hg for SBP. Conclusions: Both the Everlast smartwatches and the BodiMetrics performance monitor we tested were not accurate enough for use as BP measurement devices.

Is there a watch that monitors blood sugar and blood pressure?

The Active 2 also has many watch faces that display this data for you to choose from. Another feature that diabetes patients may find useful is its blood pressure detector, though you’ll have to ensure your watch has up-to-date software.

Is wrist or arm blood pressure more accurate?

Blood pressure readings tend to skew higher when measured with wrist monitors. In fact, the American Heart Association (AHA) advises against wrist blood measures for home monitoring. According to the AHA, home monitors that are used on the upper arm are generally more accurate.

Can a smartwatch measure cholesterol?

Blood pressure readings tend to skew higher when measured with wrist monitors. In fact, the American Heart Association (AHA) advises against wrist blood measures for home monitoring. According to the AHA, home monitors that are used on the upper arm are generally more accurate.

Do any watches check blood sugar?

K’Watch Glucose is a CGM (Continuous Glucose Monitor) device that will track your glucose level continuously throughout the day and night. Check your sugar levels discreetly by simply glancing at the watch.

Why is my first BP reading always high?

Your first blood pressure reading will almost always be higher than the second due to a wide range of factors, both environmental and psychological. These factors include white coat syndrome, stress, and having a full bladder.

Can smartwatches cause heart problems?

The study showed that technologies like smartwatches and other wrist-worn devices may heighten awareness and attention to normal and abnormal fluctuations in heart rates, which may lead to substantial increases in anxiety in patients and prompt unnecessary medical care.

Can an Apple Watch measure blood sugar?

An Apple Watch owner has created a complication and watchOS app that works with a glucose monitor, so they can keep track of their blood glucose level from their wrist.

Can you check blood sugar without pricking finger?

If you’re looking for a blood sugar monitor without finger pricks, a noninvasive CGM can also measure your glucose. Depending on the type of meter you choose, you may have to wear a sensor on different areas of the body and switch it out after a certain amount of time.

yamaytech.com

YAMAY Bluetooth Headphones with Microphone

Q: Why does the mute button not work?
A: Mute function only works for calls on cell phones at present. We are improving this function so that it would be used on other third party apps and PCs in the future.

Q: How to connect the headset to the computer?
A: Here are the steps of how to connect the headset to the computer:

1. Press and hold the MFB button for about 7s to turn on the headset and enter the pairing mode. (When the headset is in pairing mode, the LED lights will flash red and blue alternately)
2. Turn on the settings on the computer: Setting-Devices(Bluetooth, printers, mouse)
3. Turn on Bluetooth on the computer, and then click ‘Add Bluetooth or other device’.
4. Click ‘Bluetooth’, find the device ‘M20’, click ‘M20’, and confirm that the ‘M20’ has been successfully connected.
5. Then go back to ‘Settings’, click ‘System’, click ‘Sound’ and choose M20 as the output and input devices.
6. Double check whether ‘M20’ appears in the computer’s Bluetooth list.

Q: Why does the headset can’t connect to the device and stay connected?
A: Please check the following two points:

1. Please make sure M20 is within the Bluetooth transmission distance(33ft) with your device and there is no obvious obstacle between them;
2. Please make sure that the headset is not connected to another device, try to clear the Bluetooth list of the headset: In the power-on state, press and hold the multi-function button and the volume “+” button together for 5-7 seconds till pink LED flash twice at the same time. And then reconnect the headset to the device.

Q: Why the sound quality of headset is terrible?
A: Regarding the sound quality, please check the following five points:

1. Before using M20, please make sure your cellphone or other devices have a good performance in sound clarity and stability for current soundings. Then please try to connect the headset directly to the phone, and then make a call to test whether the headset sound is normal.
2. The international standard Bluetooth operating distance is 33ft.Please make M20 close to the paired device to make the communication more quickly and stable and there is no obvious obstacle between them. If it exceeds the distance and is in a place with obstacles (such as partition walls), it will affect the sound quality and call quality.
3. Please make sure M20 has enough power to work normally.
4. When using third-party software to call, if the network is not good and the use environment is interfered, the quality of the call will be affected.
5. M20 may be not compatible with some third party applications to work normally.
   Note: Please inquire us if you have any doubts. We offer lifetime after-sales service. Contact the seller on amazon for help. (Go to Your Order- Find the order ID in the list- Click ‘Contact with us’)

The FAQ Of YAMAY GT Band

How to charge the tracker?

1. Just separate the main watch body and the strap (Pull out the strap which is below the touch key), you will see the built-in USB plug with metal pins.
2. Insert the metal pins into any USB port/wall charger.
3. After a gentle vibration, a battery icon will be shown on the screen when it is being charged successfully.

*Note: If the watch does not vibrate, please turn it over to the opposite to charge again. (Please ensure that the metal strips align with the USB strips.)

How to bind the tracker to your phone? (Set up)

Please download the VeryFit app from App Store/Google Play or scan the QR code above to download.(Please don’t connect the watch via the Bluetooth pairing list of your phone.)

1. Open the VeryFit app on your smartphone, fill in your personal info and step goal.
2. Go to the “Device” page, tap “Add Device” and select “Bracelet”, then your smartphone starts searching for devices. When “GT Band” appears, tap it to connect the tracker to your smartphone.
3. You can also use the VeryFit app to scan the QR code displayed on your tracker to connect it to your smartphone (Go to the “Device” page → tap scan icon in the upper right corner of the page to scan the QR code on the tracker).

https://www.idoocloud.com/q/Veryfit.html

Compatible with most iOS 9.0 & Android 4.4 above smartphones(Not for PC, Tablet or Samsung J3)

How to activate the weather notification & music control function of the tracker?

Please make sure the watch is connected with the ‘VeryFit’ app successfully open the app and click the ‘Device’ below to trap the GT Band icon‘Device Settings’Switch on the ‘Music Control’ or ‘Weather’ option.
*Note: The weather will not be updated if disconnection occurs.

 How to check my sleep data?

Please sync the watch to the ‘VeryFit’ app when you wake up, then the detailed sleep data will show on the tracker. You can also view a comprehensive analysis graph of your sleep quality data in the app.
*Note: The GT Band will only record the sleep lasting more than 3 hrs.

Why doesn’t my charge last more than 3 days?

1. Please make sure the tracker is connected with the VeryFit app successfully–>Click the “Device” below–>Tap “GT Band” icon–>Click “Health Monitoring” and choose “HR Monitoring”–> Switch on the “Automatic measurement” instead of “Real-time monitoring”.
   *Note: The real-time monitoring tracks your heart rate once per second, but automatic measurement only tracks your heart rate every 5 mins, so the battery will last longer under automatic measurement mode.
2. And please also make sure you have fully charged the watch in the correct way. (Refer to the Question #1)

How to activate the call/text messages/SNS notification function?

Please make sure the tracker is connected to the VeryFit app successfully. Then turn on both the “Call Reminder” & “Message Notification” functions in the VeryFit app: Open app–> Click the “Device” below–> Tap the “GT Band“ icon–> Turn on “Call Reminder” & “Message Notification”–> Click the “√” icon at the top right to save the settings.

How to switch 12 hr/24 hr time display mode?

Please make sure the watch is connected with the ‘VeryFit’ app successfully–>Open the app and click ‘My’ below–>Click “Setting’–>Change the time model/unit.

How to turn on the watch again after you turn it off?

You just need to plug it into any USB port/wall charger to charge it to turn it on again. (Refer to question #1)

How to customize your home screen?

you can customize the home screen of your tracker following the steps below:
Method 1:

1.  Tap the touch key to light up the screen, then long-press the screen for 3-4 seconds.
2. Swipe left/right to choose one and tap to confirm.

Method 2:

1. Open the VeryFit app→go to the “Device” page → tap “GT Band” → “Watch face market” → “More”.
2. Select a watch face or choose a photo in your phone album to display on the home screen.

How to set up Alexa?

1. Go to the “Device” page in the “VeryFit” app. Then tap the “GTBand” icon → “Amazon Alexa”.
2. Log in to your Amazon account or create one if necessary.
3. Read about what Alexa can do–>Click “Continue” and tap “Close” to return to your device settings in the VeryFit app.
4.  Swipe right of the tracker to go to Alexa voice control. Or press and hold the home button to start talking to Alexa.
5.  To change the language Alexa recognizes or disconnect your Amazon account, tap “Amazon Alexa” on the device information page in the app.
6. The VeryFit app must be allowed to keep running in the background on your phone. And please also make sure the app is connected to WiFi or can access Cellular Data. Otherwise, you may experience a delay in Alexa’s response time, or Alexa may not be able to recognize your voice command.

*Note:

1. Saying “Alexa” will not activate the voice assistant on your tracker–You must open Alexa voice control by clicking the Alexa icon of tracker or press and hold the home button to open it.
2. Not all skills work with the tracker, as they must be able to display feedback as text on the tracker’s screen. This tracker doesn’t have a speaker, so you won’t hear Alexa respond.

My tracker is not getting any notification. How do I fix that?

For iPhone:

1. Please give Phone/Messaging/Call log permissions when you install the VeryFit app for the first time.
2. Turn on both the “Call Reminder” & “Message Notification” functions in the VeryFit app: Open app–> Click the “Device” below–> Tap the “GT Band“ icon–> Turn on “Call Reminder” & “Message Notification”–> Click the √ icon at the top right to save the settings.
3. Allow the VeryFit app to send notifications: Open your phone settings–> Find “VeryFit” app–> Notifications–> Click “Allow Notifications”–> Tick Lock Screen/Notification Center/banners, and tick “Always(Default)” in Show Previews.*Note: The watch won’t receive any notification if messages/calls/SNS notifications didn’t appear on the dropdown of your phone, make sure they are able to show up: Phone Settings–>Notifications> Find the app you need to get notification from–>Allow Notifications. (Same process as the pic above.)
4. Go to the homepage of the VeryFit app and swipe down the screen to finish the synchronization. If the watch still can’t receive any notification: Please delete the “GT Band” from the Bluetooth paired devise list from your phone–> Delete VeryFit app and download again–> Repeat the step #1-3.

For Android:

1. Please give Phone/Messaging/Call log permissions when you install the VeryFit app for the first time.
2. Turn on both the “Call Reminder” & “Message Notification” functions in the VeryFit app: Open app–> Click the “Device” below–> Tap the “GT Band“ icon–> Turn on “Call Reminder” & “Message Notification”–> Click the √ icon at the top right to save the settings.
3. Please allow the VeryFit app to send notifications and also keep running in the background of your phone. Otherwise, it will be refreshed to cause the disconnection:
   <1>Phone Settings–> Apps–> Find “VeryFit” app–> Turn on Notification”–> Also allow the “Phone”&” Messaging” permission. (Refer to the pic below)
   <2>Phone Settings–>Find “VeryFit” app–> Launch settings–> Switch on “Run in background”
   Please make sure your phone’s dropdown can show you the message notification when it comes in.
4. Go to the homepage of the VeryFit app and swipe down the screen to finish the synchronization. If the watch still can’t receive any notification: Please delete the “GT Band” from the Bluetooth paired devise list from your phone–> Delete VeryFit app and download again–> Repeat the step #1-3.

Why is the tracker screen locked when entering the swimming mode?

When entering the “pool swim”/”open water swim” mode, the screen of the tracker will be locked automatically to prevent mistakenly touching while swimming. Just scroll the screen in the direction of the arrow twice to unlock it.

Hey! We offer 30 days full refund, 12 months warranty, lifetime technical support.

If you have any other issues while using. Please feel free to contact us via your order (We will reply within 24hrs):

1. Go to Your Orders
2. Find the order ID in the list
3. Click “Contact with us”

01 Wear the watch for a distance of about one finger from the wrist and adjust the tightness of the wrist strap to a comfortable position.
Tip: Wearing too loose may affect the heart rate sensor’s data collection.

 Pairing

1. Press and hold the watch to operate ， use the mobile phone to scan the QR code on the watch screen, download and install the APP. You can also scan the QR code below to download and install it in the mobile application market.
   http://api.start.king-wear.top/mobile/sports-yamei-apk-download
2. Open Run to Sport, select (add device) on the device page, and follow the on-screen instructions.

Tips

1. During the pairing, please confirm that the Bluetooth of the mobile phone is turned on to ensure the normal connection between the watch and the mobile phone.
2. If the device cannot be found, or the device cannot be connected, try to press and hold the power button of the watch for 3 seconds, select to reset in the operation interface, and then add the device again.

Instruction

a. the home page of the dial slides top from the bottom to open the control panel

b. the home page of the dial slides bottom from the top to open the message

c. Slide from left to right to open the main menu

d. Long press the watch face interface for 3 seconds to change watch faces

e. long press power key for 3 seconds to power on/power off

f. click the power key to pause and continue the status of the sport

g. Click the power key and go back to watch face interface h.click and go back to the last menu.

04 function

	13 sports modes (running, walking, cycling, mountaineering, yoga, skipping, tennis, baseball, basketball, table tennis, badminton, football, rugby)
	Heart rate: 24H real-time heart rate monitoring throughout the day, you can view historical heart rate data
	Status: Detailed records of daily steps, step distance, calories
	Sleep: Record sleep time and sleep status in detail
	Stopwatch: timing
	Sync information: Information reminder, sync notification push on a mobile phone.
	Settings: Shutdown/Restore/About/APP Download

05 Slide from right to left accordingly to quick interface

	Status: Detailed records of daily steps, step distance, calories
	Heart rate: 24H real-time heart rate monitoring throughout the day, you can view historical heart rate data
	Sleep: Record sleep time and sleep status in detail
	13 sports modes (running, walking, cycling, mountaineering, yoga, skipping, tennis, baseball, basketball, table tennis, badminton, football, rugby)
	Music: can Remote control the music on the phone

Charging

1.  Place the watch on the charger to make sure the charging contacts and the metal contacts are completely fit.
2. Connect the charging cable to a standard USB charger , with an output voltage of 5V and an output current of 0.5A and above. If the watch cannot be turned on after being left for a long time, wipe the charging contacts of the charging cable clean when using it again to avoid sweat or moisture residue.

 basic parameter

After-sale service

l. 1. When the product is in normal use, if there are product quality problems caused by manufacturing, materials, design, and other reasons, the motherboard will be free of charge within one year from the date of purchase, and the battery and charger will be guaranteed for six months.
2. For the failure caused by the user’s personal reasons, a free warranty is not provided,
as follows:
1) Failure caused by unauthorized disassembly and reassembly of watches.
2). Failure caused by accidental drop during use.
3). All man-made damage or misuse due to the third party (such as the host enters the water, the external force cracks, Damage of scratches on peripheral parts, etc.) is not covered by the warranty.
3. When requesting a free warranty, please provide a  warranty card with the date of purchase and the stamp of the place of purchase.
4. When the user repairs the product, please take the product to our company or our distribution stores.
5. All the functions of the product are mainly based on the real product.

FCC STATEMENT :

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

RF warning statement:
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.