Loading manuals...

SONICWALL NSa 3700 Network Security Appliance Manual

SONICWALL NSa 3700 Network Security Appliance Manual Image

Package Contents

  1. NSa 3700 appliance
  2. Ethernet cable
  3. Serial console cable (RJ45 to DB9)
  4. Power cord (1)
  5. SonicWall NSa 3700 Quick Start Guide
  6. Safety, Environmental, and Regulatory Information documents

NOTE: The included power cord is approved for use only in specific countries or regions. Before using a power cord, verify that it is rated and approved for use in your location. The power cord is for AC mains installation only. Refer to the NSa 3700 Safety, Regulatory, and Legal Information document for additional safety information.

Front Panel

  1. MGMT Port – RJ45:
    Solid Green = Link at speeds 1G or lower, Blinking Green = activity
  2. Console Port: Serial Console for CLI access
  3. 10/5/2.5/1GE SFP/SFP+ Ports and LEDs:
    Solid Yellow = 10, 5 or 2.5GE link, Blinking Yellow = 10, 5 or 2.5GE activity, Solid Green = 1GE link, Blinking Green = 1GE activity
  4. 5/2.5/1GE SFP/SFP+ Ports and LEDs:
    Solid Yellow = 5 or 2.5GE link, Blinking Yellow = 5 or 2.5GE activity, Solid Green = 1GE link, Blinking Green = 1GE activity
  5. RJ45 Ports and LEDs:
    Solid Green = Link at speeds 1G or lower, Blinking Green = activity
  6. SafeMode Button: If NSa is up: Press to put the NSa into SafeMode, If NSa is down: Press while connecting to power and hold until Test LED blinks yellow 3 times.
  7. Power Button: Short press = On, Off with Graceful Shutdown (Test and Alarm LEDs turn Red), Long Press (5+ sec) = Forced Shutdown
  8. USB SS 3.0 Ports: For Configuration, Recovery, Re-imaging the NSa, and USB WWAN device support
  9. Storage LED: Solid Green = M.2 storage module present, Blinking Green = Activity, Yellow = Storage warning, Off = No storage
    Alarm LED: Red = High Level Alarm (such as Fan Failure) / Power down requested, Yellow = Lower Level Alarm
    Test LED: Red = Power down requested, Yellow = Initializing, Blinking Yellow = SafeMode / FIPS test in progress, Off = Normal
    Power LED: 1 = Primary, 2 = Redundant Blue = Powered on, Yellow = Defective redundant power supply

Copyright ©2021 SonicWall Inc. All rights reserved
SonicWall is a trademark or registered trademark of SonicWall Inc. and/or its affiliates in the U.S.A. and/or other countries. All other trademarks and registered trademarks are property of their respective owners.
The information in this document is provided in connection with SonicWall Inc. and/or its affiliates’ products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of SonicWall products. EXCEPT AS SET FORTH IN THE TERMS AND CONDITIONS AS SPECIFIED IN THE LICENSE AGREEMENT FOR THIS PRODUCT, SONICWALL AND/OR ITS AFFILIATES ASSUME NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON- INFRINGEMENT. IN NO EVENT SHALL SONICWALL AND/OR ITS AFFILIATES BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF SONICWALL AND/OR ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SonicWall and/or its affiliates make no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. SonicWall Inc. and/or its affiliates do not make any commitment to update the information contained in this document.
For more information, visit https://www.sonicwall.com/legal/.

Legend

WARNING: A WARNING icon indicates a potential for property damage, personal injury, or death.
CAUTION: A CAUTION icon indicates potential damage to hardware or loss of data if instructions are not followed.
IMPORTANT, NOTE, TIP, MOBILE, or VIDEO: An information icon indicates supporting information

To access the Support Portal, go to https://www.sonicwall.com/support.

Back Panel

  1. System Fans (2)
  2. Redundant Power Input (with cover plate):
    A redundant power supply can be ordered separately.
  3. Primary Power Input

Connect and Power On

To power on your NSa and connect to it for initial setup:

  1. Connect the provided power cord to the appliance and to an appropriate electrical outlet (100-240 volts). The NSa powers on and goes through the startup sequence.
  2. Using the provided Ethernet cable, connect one end to your management computer and the other to the MGMT port on the appliance.
    The MGMT port is a dedicated 1 Gigabit Ethernet port for appliance management and SafeMode access.
  3. Connect the NSa LAN interface (X0 by default) to your local, internal network.
  4. Connect the NSa WAN interface (X1 by default) to the Internet.

TIP: You’ll need internet connectivity for the product registration process. After initial setup, connect your computer to the NSa X0 interface or to the LAN subnet. You cannot reach the internet or other external destinations while connected to the MGMT interface without first configuring a default gateway in its interface settings.

Setup Options

Setup using Local Management
Set up and manage your NSa by connecting it to a management computer via Ethernet cable.
To minimize scrolling, set your screen resolution to at least 1920 x 1080 pixels.
Setup using Cloud Management
Use SonicWall Capture Security Center (CSC) with Zero Touch to manage and configure your NSa from the cloud.
Setup using SonicExpress App
Use SonicWall SonicExpress on your smartphone to register and configure your NSa

NOTE: After initial setup, be sure to download the latest firmware from MySonicWall and upgrade your NSa.

Initial Setup and Registration Using Local Management

  1. Connect the MGMT interface to your computer. The NSa provides a DHCP address for your computer.
  2. Navigate to https://192.168.1.254 in your web browser and log in with the default credentials:
  3. Username: admin
    Password: password
  4. Launch the Setup Guide wizard or manually configure the NSa to configure your WAN interface, change the admin password, and select other settings.
  5. After completing the setup wizard, connect your computer to the LAN or WAN network and log into SonicOS/X.
  6. Click Register and enter your MySonicWall credentials to register your NSa.

TIP: Registering the appliance from SonicOS/X requires that DNS settings are configured for the WAN interface. For DHCP WAN type, DNS is set automatically.
NOTE: Your appliance must be registered to download the latest firmware from MySonicWall. SonicWall recommends upgrading your NSa to the latest available firmware.

Cloud Management

Use Capture Security Center (CSC) with Zero Touch to manage and configure your NSa.

NOTE: This option requires a Cloud Management license.

  1. Log into CSC at cloud.sonicwall.com using your MySonicWall credentials.
  2. Select the MySonicWall tile to register your NSa.
  3. Enable Zero Touch and NSM licensing on your NSa in MySonicWall.
  4. Select the Network Security Manager tile in CSC to manage your NSa from the cloud.

SonicExpress App

Use SonicExpress on your smartphone to register and configure your NSa.

  1. Download and launch the SonicExpress App on your iOS or Android device.
  2. Tap Login and log in with your MySonicWall credentials.
  3. Select the Tenant for the NSa. Tenants can contain multiple SonicWall appliances.
  4. Connect your iOS/Android device to the NSa with the smartphone USB cable. This cable is not supplied with the NSa.

    NOTE: Use the USB cable from your mobile device.
  5. Use the Setup Guide to register the NSa, synchronize service licenses, change the password, and configure essential interface settings.

SonicWall Secure SD-Branch

SD-Branch combines SD-WAN, SD-LAN, unified security and centralized management for distributed enterprises.

For product information, use the QR code or go to