vooni LED Strip Light with Remote
PARTS INCLUDED
- 5 METRES RGB LED STRIP
- IR WIRELESS REMOTE CONTROL
- CONTROL UNIT WITH IR SENSOR
- POWER ADAPTER WITH CORD
- USER MANUAL
SPECIFICATIONS
- STEADY LIGHT IN 20 DIFFERENT RGB COLOURS
- DIFFERENT LIGHT MODES WITH FADING AND FLASHING LIGHTS
- 6 PROGRAMMABLE DIY BUTTONS
- LENGTH: 5 METRES
- THE LED STRIP IS APPROX. 6 MM THICK AND 10 MM WIDE
- SELF-ADHESIVE REAR SIDE WITH FOAM TAPE FOR EASY INSTALLATION
- THE INSTALLATION SURFACE MUST BE SMOOTH, CLEAN AND DRY
- 150 LED LAMPS
- USEFUL LIFE: 20,000 HOURS
- THE STRIP IS PLIABLE AND CAN BE CUT TO THE DESIRED LENGTH FOLLOWING THE CUTTING LINES
- FOR INDOOR USE (IP65)
- THE CONTROL UNIT CAN BE FIXATED BY SCREWS OR SELF-ADHESIVE TAPE (NOT INCLUDED)
- REMOTE CONTROL RUNS ON ONE CR2025 BUTTON CELL (INCLUDED)
- LENGTH OF CORD (FROM THE CONTROL UNIT TO POWER ADAPTER): 85 CM
- POWER: 36W
- OUTPUT: 12V/3A
- INPUT: AC ADAPTER RATING 100-240V, 50/60HZ
- N.B.! SHOULD NEVER BE CONNECTED TO AC220V OR DC24V
SETUP
- ARRANGE THE LED STRIP AS YOU WISH.
- THE STRIP IS PLIABLE AND CAN BE CUT TO THE DESIRED LENGTH FOLLOWING THE CUTTING MARKS SEEN ON THE STRIP.
- CONNECT THE LED STRIP WITH THE CONTROL UNIT.
- THERE IS A SMALL ARROW ON BOTH THE LED STRIP CONNECTOR AND THE CONTROL UNIT CONNECTOR, MAKE SURE TO LINE UP AND CONNECT THEM ARROW TO ARROW.
- REMOVE THE PLASTIC BATTERY PROTECTION COVER POINTING OUT FROM THE REMOTE CONTROL.
- POINT THE REMOTE CONTROL TOWARDS THE CONTROL UNIT IR SENSOR AND PRESS ON/OFF BUTTON ON THE REMOTE TO TURN ON THE LIGHTS.
WARNING!
- THE SUPPLY VOLTAGE OF THIS PRODUCT IS DC12V, NEVER CONNECT TO DC24V OR AC220V
- NEVER CONNECT TWO WIRES DIRECTLY IN CASE OF SHORT CIRCUIT.
REMOTE CONTROL
BRIGHTNESS UP / DOWN – INCREASE OR DECREASE THE INTENSITY OF THE LIGHT
RUN / PAUSE – PRESS DURING ANY JUMP, FADE OR FLASH MODE TO PAUSE THE CYCLE, PRESS AGAIN TO CONTINUE IT
ON / OFF – PRESS TO TURN THE LED STRIP ON, PRESS AGAIN TO TURN IT OFF
STATIC COLOURS – PRESS ANY OF THE 20 COLOURED BUTTONS TO CHOOSE RED, GREEN, BLUE OR GRADES OF THOSE COLOURS, OR STATIC WHITE LIGHT
QUICK – PRESS DURING ANY JUMP, FADE OR FLASH MODE TO SPEED UP THE COLOUR CHANGE, THERE ARE 8 DIFFERENT SPEEDS
SLOW – PRESS DURING ANY JUMP, FADE OR FLASH MODE TO SLOW DOWN THE COLOUR CHANGE, THERE ARE 8 DIFFERENT SPEEDS
AUTO – PRESS TO START AN AUTOMATIC COLOUR CYCLE
FLASH – PRESS TO CHOOSE BETWEEN 8 DIFFERENT FLASHING MODES
JUMP 3 & JUMP 7 – PRESS TO MAKE THE LIGHT JUMP BETWEEN EITHER 3 OR 7 DIFFERENT COLOURS
FADE 3 & FADE 7 – PRESS TO MAKE THE LIGHT FADE IN AND OUT BETWEEN EITHER 3 OR 7 DIFFERENT COLOURS
DIY 1-6 – PROGRAMMABLE BUTTONS TO QUICK-SELECT YOUR FAVOURITE COLOUR.
HOW TO USE DIY BUTTONS
- PRESS THE DIY BUTTON THAT YOU WANT TO PROGRAM.
- LONG PRESS ANY OF THE COLOURED ARROW BUTTONS TO MODIFY THE LIGHT WITH EITHER RED, GREEN OR BLUE COLOUR. UPWARD ARROWS WILL INCREASE THE SELECTED COLOUR NUANCE, AND DOWNWARD ARROWS WILL DECREASE IT.
- KEEP LONG-PRESSING THE DIFFERENT ARROWS UNTIL YOU ARE HAPPY WITH THE COLOUR MIX.
- SAVE THE ADJUSTED COLOUR BY PRESSING THE SAME DIY BUTTON AS YOU STARTED WITH.
- NOW YOU CAN EASILY SELECT YOUR FAVOURITE LIGHT COLOUR JUST BY PRESSING THE PROGRAMMED DIY BUTTON.