Loading manuals...

UNION 62983 Electronic Digital Wall Safe Manual

UNION 62983 Electronic Digital Wall Safe Manual Image

UNION 62983 Electronic Digital Wall Safe

Specifications

External Dimensions 3-1/2″ L x 13-3/4″ W x 22-3/4″ H
Batteries 4 AA (sold separately)
Weight 29 lb

SAFETY INFORMATION

Installation Precautions

  1.  Verify that the installation surface has no hidden utility lines before drilling or driving screws.
  2.  Wear ANSI-approved safety goggles during installation.
  3.  Mount securely before use.
  4.  Install only according to these instructions. Improper installation can create hazards.
  5.  Keep installation area clean and well lit.
  6.  Keep bystanders out of the area during installation.
  7.  Do not install when tired or when under the influence of alcohol, drugs or medication.

Use Precautions

  1.  Keep closed and locked whenever unattended. RISK OF CHILD ENTRAPMENT AND SUFFOCATION. Check inside before closing. Do not allow children to play with or near safe. Keep keys and codes away from children.
  2.  Keep clear of the door when closing.
  3.  Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. Position batteries in proper polarity. Do not use swollen or leaking batteries.
  4.  Use as intended only.
  5.  Inspect before every use; do not use if parts are loose or damaged.
  6.  Maintain product labels and nameplates. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.
  7.  Do not store Keys inside of the Safe. Place the keys in a secure location outside of the safe.
  8.  The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors that cannot be built into this product, but must be supplied by the operator.
  9.  The Safe is not fireproof.

Set-up and Operation

Functions

Set-up and Operation

Note: Set up and test Safe before Installation. Open Safe with Key Note: Do not store Keys inside Safe. Opening withKey may be necessary when replacing batteries or if Entry Code is forgotten. Store Keys in secure place outside of Safe.

  1.  Remove Keyhole Cover.
  2.  Insert Key and turn counterclockwise.
  3.  Turn the Knob clockwise and Open the Door.
  4.  Remove Key and replace Keyhole Cover.

Install/Replace Batteries

  1.  Remove Battery Cover.
  2.  Install batteries (sold separately). Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. Position batteries in proper polarity. Do not use swollen or leaking batteries.
  3.  Replace Battery Cover. Leave door open until Entry Code is set. Note: Red light will illuminate when batteries need to be replaced. Dispose of used batteries according to local regulations.

Set/Reset Master and User Entry Codes

Note: Leave door open while setting Entry Codes. Write down Entry Codes and store in secure place outside of safe. 1. Set/Reset Master Code: a. Press 00 on Keypad, then press andhold Entry Code Button until Safe beeps and Yellow light illuminates. b. Within 15 seconds, enter an Entry Code up to 8 digits on Keypad, followed by either A or B.

  •  Code has been accepted when Safe beeps.
  •  Code has not been accepted if Yellow light turns off without beeping.

Open Safe with Entry Code

  1.  Enter Entry Code (Master or User). Safe will beep twice and Green light will illuminate.
  2.  Turn Knob clockwise and open Door.Note: Safe will automatically lock if not opened within a few seconds of accepting Entry Code. Note: Keypad will disable for 5 minutes if Entry Code is entered incorrectly three times in a row.

Installation

  1.  Choose location, then locate studs, 16″ apart, with a stud finder (not included). Mark stud locations.
  2.  Cut out small section of drywall next to stud, then check inside for electrical wiring or plumbing that might interfere with installation.
  3.  Measure back of Safe and transfer measurements to wall.
  4.  Cut along marked lines and remove drywall.
  5. Place Safe into hole, using shims if necessary.
  6.  Locate two mounting holes on each side.
  7.  Secure Safe with fasteners that are rated to support the weight of the Safe and its contents.

Maintenance

  1.  Protect Safe from moist or wet conditions. Moisture may cause electronic damage in the keypad or corrosion of the steel.
  2.  Occasionally wipe the safe and keypad clean with a soft dry cloth or brush.
  3.  Do not get any oil or other liquids on or near the electronic mechanism.
  4.  If key lock sticks, use graphite lubricant, such as pencil lead. Rub pencil lead over Key, then insert Key and turn back and forth. Repeat until lock moves freely

Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuriesto persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.