Mic-D30 Microphone
User Manual
Guangzhou Zhiying Technology Co., Ltd
Block 15th, No.200 Fangcun Avenue East, Liwan District, Guangzhou, China, 510000
[email protected]
www.syncoaudio.com
https://www.facebook.com/syncomicrophones
Thank you for choosing SYNCO Mic-D30
Please read this manual carefully before use and follow all instructions mentioned herein.
Feature Introduction
- Super cardioid capsule for excellent off-axis sound rejection
- 75Hz/ 150Hz low cut filter
- Overdrive Protection
- Stepless gain adjustment dial
- Support real-time audio monitoring
- Type-C to 3.5mm TRS/ TRRS output
- Dual shock mount to firmly hold the mic
Caring For Your SYNCO Mic-D30 Microphone
- Please keep the product in a dry, clean, dust-free environment.
- Keep corrosive chemicals, liquids, and heat sources away from the product to prevent mechanical damage.
- Use only a soft and dry cloth for cleaning the product.
- Malfunction may be caused by dropping, the impact of external force.
- Do not attempt to disassemble the product. Doing so voids the warranty.
- Please have the product checked or repaired by authorized technicians if any malfunctions happened.
- Failure to follow all the instructions may result in mechanical damage.
- Warranty does not apply to human errors.
Package List
The package includes the following items
 |
SYNCO Mic-D30 Microphone *1 |
 |
Packing Box *1 |
 |
Furry Windscreen *1 |
 |
Shock Mount *1 |
 |
User Manual *1 |
 |
Type-C to USB Charging Cable *1 |
 |
Type-C to 3.5mm TRRS Phone Cable *1 |
 |
Type-C to 3.5mm TRS Camera Cable *1 |
Components Introduction
- 75Hz Low Cut Indicator
- 150Hz Low Cut Indicator
- Low Cut Button
- Overdrive Protection Indicator
- ON-OFF & Battery Indicator
- ON-OFF/ Overdrive Protection
- Type-C Charging & Output Port
- Headphone Output
- Gain Adjustment Dial
Operations
-
The Use of Furry Windscreen
Mic-D30 comes with a furry windscreen to eliminate the noise caused by wind while recording. Please install the windscreen to the microphone as shown below.
-
Charging the Mic-D30 Microphone
The Mic-D30 has a built-in battery. Please fully charge the microphone with the Type-C Charging Port and Type-C to USB Charging Cable before use.
(Note: The ON-OFF & Battery Indicator will fast flash when the mic is running out of power. When the mic is charging, the
the indicator will flash slowly then stay green when it is fully charged.)
-
Using with Your Device
The package includes a shock mount, which has a cold shoe on the bottom.
It helps to mount the microphone on recording devices like DSLR, camera, camcorder.
① Securely place the microphone into the shock mount.
② Install the shock mount to your recording devices via the cold shoe and tighten the screw.
③ Connect the microphone with your device via the Type-C to 3.5mm Cable. (Note: Some smartphone devices may require an adapter like Lightning to connect with the microphone. The adapter is not included in the package.)
④ Long press the ON-OFF button to turn on the microphone. (Note: Short press for Overdrive Protection function.) -
Real-time Audio Monitoring
It is suggested to use the headphone whose impedance is under 55 Ohm to monitor the audio. Plug your headphone into the Headphone Output, then you can real-time monitor your recording.
-
Low Cut Button
First press for 75Hz low cut, second press for 150Hz low cut and the third press to turn off the low cut function.
Specifications
- Polar Pattern: Super Cardioid
- Performance Parameter
| Transducer | Back Electret Condenser |
| Polar Pattern | Super-Cardioid |
| Frequency Response | 20 Hz to 20 kHz |
| Dynamic Range (Typical) | 119dB SPL (A-weight per IEC651) |
| Signal/Noise | 82dB（1KHz at 1Pa）(A-weight per IEC651) |
| Sensitivity | -24dB±2dB （1dB=1V/Pa at 1kHz） |
| Maximum SPL | 124 dB SPL |
| Output Impedance | 300Ω±20%（at 1kHz） |
| Low-Frequency Roll-off | 75Hz/150Hz |
| Output Interface | Type-C to 3.5mm |
| Dimensions | Φ21.5×214.5mm |
| Weight | 85g |
