OVE Smart Toilet TUVA Manual

OVE Smart Toilet Instruction Manual

youtu.be/SyNhbmO06Uo

SAFETY NOTICE

ATTENTION! BEFORE INSTALLING THE PRODUCT, YOU MUST READ AND UNDERSTAND CAREFULLY ALL BELOW WARNINGS.

It is forbidden to disassemble toilet by yourself.
Please do not set this product in a wet place, because it is an electronic product. If set in the bathroom, please insure that there is proper air flow.
Please insure that the product is set more than 0.6 meter away from the bathtub.
Please make sure electric power is AC 120V. Ensure the electrical socket can bare a load of 1500W power (or else it can cause fire or electrical shock).
Please make sure the electrical source is well grounded.
Please do not put any water or detergent on the product or its electrical plug.
Do not touch the electrical plug with a wet hand (or else it can cause fire or electric shock).
Do not use the product if it has these following problems. When any of the following problems occur, turn off the electricity and close the water valve.
• Water leaking from the pipe or the main body.
• Crack or breakage
• Abnormal sound or smell of the product
• Smoke coming out from the product
Keep any flame or flammable products away from the toilet.
Please do not step on the toilet seat, the seat cover, the main body, or put anything heavy on the product. Otherwise, the product may break and may cause injury or the product may break and may cause indoor flooding.
Please do not put your finger or anything else into the outlet of the drying blower.
Please do not touch or cover the drying blower outlet with clothes, or it may lead to burn injury or electric shock.
Please do not tightly bend or press the flexible supply hose, or it may lead to water leakage or it may decrease the water pressure.
Please clean the product with soft cleaning products.
Please do not use any harsh detergents to clean the product.
Please do not throw anything other than toilet paper into the toilet or it may lead to blockage and indoor flooding.
Please be careful to not let objects like a comb, toothbrush or other stuff fall into the toilet.

WARNINGS

Do not leave the toilet exposed to the sun. May cause yellowing or color fading.
Direct sunlight affects the good functioning of the remote.

Radio or transmitting devices may interfere with the toilet’s remote control functions

If the power cut off during washing and the nozzle is still out: Do not push it back manually, it will revert to its resting position once the power is back ON.

If power cuts off during nozzle self-cleaning, the water will continue to flow out. Manually close the inlet water valve of the toilet until power comes back ON.

Be careful not to spill water on the top of the toilet: Electronics are located under the plastic cover.

To prevent against power surge damages, make sure the ground is working in the power socket.

If you do not plan to use the toilet for a long time, close the inlet water valve and unplug the toilet.

Do not use DC current. Only AC 120V with load capacity over 1500W are accepted.

Do not expose the toilet to freezing temperature. This will void the warranty and damage the piping.

Do not lean on the cover.

BATTERY USAGE SAFETY GUIDELINES

Always purchase the correct size and grade of battery most suitable for the intended use.
Clean the battery contacts and also those of the device prior to battery installation.
Remove batteries from equipment which is not to be used for an extended period of time.
Remove batteries if consumed or if product is to be left unused for a long time.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-MH, etc.) batteries.
Do not dispose of old batteries in the trash! Please dispose of your used batteries at your local collection center.

FCC WARNING
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

EXTENSION CORD WARNING
a) The short power-supply cord is provided to reduce the risk resulting from becoming entangled in or tripping over a long cord.
b) Extension cords are available and may be used if care is exercised in their use. c) If an extension cord is used:
1) The marked electrical rating of the detachable power-supply cord or extension cord should be at as great as the electrical rating of the appliance.
2) If the appliance is of the grounded type, the extension cord should be a grounding type 3-wire cord.

FILTER WARNING
The physiological effect of the operation of this appliance, beneficial, or otherwise, have not been investigated by CSA.

POWER SUPPLY:
120V / 1300W / 60Hz

PART LIST

INSTALLATION INSTRUCTIONS

Remove the seat from the ceramic base. Simply pull the seat up gently. Be careful, there are wires that need to be disconnected before you can remove the seat completely (see step #2).

Unplug the electrical cord and the water tube before completely pulling away the toilet seat.

Unplug the cord.

To unplug the water tube:
1) Remove the blue clip.
2) Push the ring down with your fingernail.
3) While still pushing the ring down, gently pull-out the water tube.

NOT SUPPLIED

Install the floor drain cover connector according to the manufacturer’s recommendations.

Position correctly the two fixing bolts of the floor drain. Follow manufacturer’s recommendations.

Insert the ring gasket under the toilet.

Position the toilet on the floor drain, making sure the fixing bolts are aligned with the toilet’s holes.

Using a ratchet, tightly screw the nut to the fixing bolts.

Reconnect the electrical cord. Make sure both ends are well aligned.

Reconnect the water tube:
1) Gently, but firmly push the tube inside the hole.
2) Re-insert the blue clip.

With care, re-install the seat on the ceramic base. Make sure no wires get squeezed or tangled.

Connect the water inlet fitting to the water supply.

Connect the toilet’s water inlet with the supplied water supply hose.

Apply silicone around the base of the toilet. Wait for 24h for it to dry.

BATTERY INSTALLATION

In order to make sure the flushing can work in the event of a power shortage, install a durable battery at the side that will power the flush valves in such events:

Open the window-shade located at the right side of the toilet.
Open the battery cover.
Securely put the battery in place, as shown on the drawing.
Close the battery cover and window-shade.

Load the remote with two AAA batteries. The battery compartment is located at the bottom back of the remote and is opened by firmly sliding the cover downward.

FIRST TIME USE

Open the water supply inlet valve.
Plug the toilet in the power socket.
The toilet’s blue light will start blinking.
The blinking light indicates that the wash tank is filling with water, a sensor in the toilet will stop the filling process automatically after around 3 minutes when the tank is full of water. After the wash tank is filled with water, the indicator light will stop blinking.
The toilet will turn ON automatically. Once the beeping sounds and the flashing light have stopped, the toilet is ready for use.

Notice:

Warming up the toilet seat will take about 3 minutes.
Warming up the bidet cleaning water will take about 3 min.
Leave the power continuously ON to assure all functions are ready for anytime use.
If the toilet is not used for 24h, it will enter in ECO MODE.

CONTROLS DESCRIPTION

BEEPING SOUNDS DIRECTIONS

1X BEEP = The toilet will give out one beeping sound every time it successfully receives a command from the Remote Control.
2x BEEP = The toilet will give out two beeping sounds every time it has successfully received a command, but cannot execute it. For example, if the Seat Sensor is not active and the user presses the BIDET/MOVE button, the toilet will beep two times because the bidet function cannot be active if the seat sensor is not active.
3x BEEP = The toilet will give out three beeping sounds every time it has successfully received a command, but the function the user is trying to adjust has already reached its maximum or minimum setting.
BEEPING for Temperature levels:
While adjusting the temperature for the Bidet/Spray water, the Seat or the Drying Air, the toilet will beep as follow to indicate which temperature has just been set:
-ROOM TEMP = 1x long beep
-LOW = 1x short beep
-MEDIUM = 2x beep
-HIGH = 3x beep

SPRAY CLEANING (1 WATER JET)
This function will only work if the user is sitting on the toilet. Press the SPRAY/MOVE button for spray cleaning. Water will spray and clean the user. Press the button again and the nozzle will move back & forth to insure the cleanest result. You can use this key stoke to get the best cleaning effect.

BIDET CLEANING (4 JETS OF WATER)
This function will only work if the user is sitting on the toilet. Press the BIDET/MOVE button for bidet cleaning. Water will spray and clean the user. Press the button again and the nozzle will move back & forth to insure the cleanest result. You can use this key stoke to get the best cleaning effect.
If you are not seated on the toilet seat, the toilet seat sensors will prevent water from squirting out of the nozzle or warm air from flowing out of the dryer. The nozzle washes itself before and after every use with the programmed automatic nozzle washing cycle. The spray function will automatically stop after 2 minutes of continuous use. To start it again press the button. It will take about 10 seconds after pressing the BIDET/MOVE or SPRAY/MOVE button before water starts to spray out of the nozzle. Please be patient.

AIR DRYING
This function will only work if the user is sitting on the toilet. Press the DRYING button for air drying. The air will drying the user. Press the button again and the air nozzle will move back & forth to insure driest result. You can use this key stoke to get the best drying effect.
If you press the DRYING key while the toilet is flushing, you will need to wait about 10 seconds before warm wind starts to flow out of the dryer.

STOP
Pressing the stop button at any time will automatically stop any functions.
The toilet will keep spraying for 1-2 seconds after you stand up, so be sure to press the STOP button before standing up from the toilet seat, during the cleaning process.

FLUSHING
Press FLUSHING button before using intelligent toilet will clean the bowl with water automatically.

LIGHT
Pressing the LIGHT button on the remote control board will turn ON the toilet’s light, pressing the button again will turn it OFF.

INTELLIGENT FEATURES

ECO MODE
ECO MODE will cut down the electricity usage of your intelligent toilet during times of none-usage. The cleaning water tank will start heating the water only once the user is sitting on the toilet, whereas in normal mode, the cleaning water is kept to your preferences for your instant enjoyment.

SOFT CLOSE DESIGN
The toilet seat and seat cover have a soundless soft close design that prevents them from falling rapidly and denting or scratching the toilet.

ANTI-MICROBIAL SEAT
The toilet’s seat is coated with an eco-friendly antimicrobial polymer preventing the growth of any microbe on the seat. Clean by design, for your piece of mind.

SUPER SWIRL
If water keeps oozing out even after the toilet is clean, adjusting the stopcock clockwise can help reach a good flush effect. If the flush effect is still not good, adjusting the stopcock counterclockwise or cleaning the filter may help improve the flush effect.

AIR PUMP SUPERCHARGED
Press the AIR PUMP button on the remote control to activate a supercharged water pressure pump. This function will temporarily increase the water pressure for maximum cleanness.

AUTOMATIC ODOR FIGHTING CATALYZER
As soon as the user sits on the toilet, a fan sucks the air out of the toilet bowl and through an advance odor fighting catalyzer. This prevents the bad smells during the toilet’s usage, insuring a pleasant experience.

CLEANING THE FILTER

1 Close the inlet valve, turn clockwise. Do not take out the filter before closing the inlet valve.

2 Unscrew the cap of the inlet valve.

3 Clean the filter. Use a tooth brush to clean the dirt on the filter. Use a cloth to clean the dirt and deposits in the valve.
Use water instead of detergent. Do not overexert the filter while cleaning, do not damage the shape of the filter.

4 Install the filter back into the inlet valve, and screw the cap back on.

5 Open the inlet valve counterclockwise. Make sure the water does not leak out.

LONG TERM STORAGE

In order to prevent from any damages that may be caused from frozen toilet water, please drain away the remaining water according to the following methods. When leaving for a long time without using this toilet, please make sure to drain all the water from the toilet.

Close water inlet valve.
Unfasten and remove the water drain bolt.
After draining all the water, please tightly screw the water drain bolt back into place.
Make sure to drain all water from the toilet, including the water in the tank for the bidet/spray cleaning, also any water left in the seals or grooves, dry with towel.

BATTERY MAINTENANCE

In order to make sure the function of flushing can work in the event of an electricity black out, please replace the battery once a year. Take out the battery when not using the toilet for a long time.

Open the window-shade.
Open the battery cover.
Take out the battery and replace them.
Close the battery cover and window-shade.

MAINTENANCE and CONSUMER RESPONSIBILITIES

The DISTRIBUTOR does prohibits the use of harsh abrasive cleansers on any of its products. Harsh cleansers will damage the inner workings of the toilets.
For daily maintenance, use a wet cloth and a soft liquid cleaner.
Never use abrasives or cleaners containing acetone, chlorine or strong bleach, scrapers, metallic brushes, nor other objects or products which can graze or tarnish surfaces.

LIMITED 1 YEAR WARRANTY

The DISTRIBUTOR warranty is valid for a period of 1 year after purchased. Improper use of this product or any deviations to the general guidance given in the user manual will void the warranty. This non-transferable warranty applies only to the original purchaser and proof of purchase is required for all claims
This warranty applies to the DISTRIBUTOR toilet installed for residential use only. The DISTRIBUTOR warrants that, when installed in accordance with the Recognized Plumbing Industry Practice, the toilets are free of manufacturing defects for a period of one (1) year from the date of purchase.
The DISTRIBUTOR will repair or replace the damaged product or parts only if they were installed and used in a proper way according this user manual.
Before accepting to repair or replace the product, the DISTRIBUTOR is entitled to send a representative to inspect the product. We will offer free of charge service for inspecting, repairing and replacing for the items within this warranty period; However the freight charges are the customer’s responsibility.

INFORMATION ABOUT YOUR WARRANTY COVERAGE
This warranty does not cover damages or failure attributable to:

Toilets installed with obvious visual defects.
Rough handling or improper operation.
The presence of sediment or impurity in the water supply system used.
Defects or damages to toilets caused by installation that does not comply strictly with the instructions set forth in the Recognized Plumbing Industry Practice.
Defects or damage to toilets caused by severe accidents (e.g. fire, electric surge, etc.)
Damage caused by flooding or standing water from leaking pipes, faucets, household appliances, etc.; Up to and including flooding and any damage caused by acts of God.

NOTES ON WARRANTY
This warranty applies only to the original purchaser and installation site and is not transferable.

FOR WARRANTY SERVICE

To make a claim, contact the DISTRIBUTOR no later than 30 days following the date of discovery or detection of defect.
Proof of purchase, such as the bill of sale is mandatory when requesting warranty service.
The DISTRIBUTOR reserves the right to designate a representative to inspect the vanity for analysis.
No unauthorized person, installer, dealer, agent or employee of the DISTRIBUTOR or any representative is entitled to assume any liability on behalf of the DISTRIBUTOR relating to the sale of this product or has the authority to increase or alter the obligations or limitations of this warranty.

INSTALLATION PICTURE

Save this manual for future reference

CONTACT US

HEAD OFFICE
2800 Etienne Lenoir, Laval
Quebec H7R 0A3 Canada

Customer service
Tel.: 1-866-839-2888
Fax: 1-866-922-9990
[email protected]

8:00 am – 5:00 pm E.S.T Monday – Friday

English and French speaking representatives available

KEEP THIS INFORMATION
CONSERVEZ CES INFORMATIONS
CONSERVE ESTA INFORMATIÓN
Purchase date Date ________________
Product Tracking Reference ________________