Loading manuals...

AEROPEX Wireless Bone Conduction Headphones manual

AEROPEX Wireless Bone Conduction Headphones manual Image

AEROPEX Wireless Bone Conduction Headphones

A Quick Look

How to Set Up Aeropex

Charge
Charge the headphones with the included magnetic charging cable. The LED indicator will turn from red to blue when charging is complete.

Pair
Start with your headphones powered off. Enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue

Connect
Open your device’s Bluetooth® menu and select “Aeropex by AfterShokz.” Audrey says “connected” and the LED indicator will flash blue one time.

Multifunction Button (A)

Play / pause music Click once One beep
Skip to next song Double-click while music is playing One beep
Back to previous song Three-click while music is playing One beep
Answer call Click once Two beeps
End call Click once One beep
Answer call waiting and hang up on current caller Press and hold for 2 seconds One beep
Reject a call Press and hold for 2 seconds Two beeps
Prompt device’s voice assistant Press and hold for 2 seconds Device beep
Redial last number Double-click (when idle) “Redial last number”

Volume+ / Power Button (B); Volume- Button (C)

Power on Press and hold volume+ for 2 seconds “Welcome to AfterShokz”
Power off Press and hold volume+ for 3 seconds “Power off”
Mute Press and hold both buttons for

2 seconds while on a call

 “Mute on” or “Mute off”
Change EQ

setting

 Press and hold both buttons for

3 seconds while music is playing

 “EQ changed”
Check battery status Click the volume+ or volume- button while music is paused “Battery high/Battery medium/

Battery low/Charge me”
Adjust volume Click the volume+ or volume- button

to adjust volume while music is playing

 One beep

Specifications

Part number                                                     AS800 Frequency response 20Hz~20KHz
Speaker type            Bone conduction transducer Sensitivity 105 ± 3dB
Bluetooth® version                          Bluetooth®  v5.0 Microphone -38dB ± 3dB
Wireless range 10 m Battery                                     Li-Polymer battery
Compatible profiles A2DP, AVRCP, HSP, HFP Weight                                   26 g
Continuous play Up to 8 hours Standby time                                 Up to 10 days
Charge time 2 hours Warranty                                                     2 years
Frequency band 2402MHz~2480MHz Maximum RF output power                      4dBm
Charge voltage 5V±5% Water resistance                                            IP67
Speaker impedance 8.5ohm±20% Battery capacity                                     145 mAh

LED Indicator

Solid red Charging
Solid blue Charging complete
Flashes red and blue Pairing mode
Flashes blue Incoming call
Flashes red every 2 minutes Low battery

Multipoint Pairing

Multipoint pairing allows Aeropex to be connected to two devices at once, allowing users to seamlessly transition between the two.

  1. Start with your headphones powered off.
  2. Press and hold volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
  3. Press and hold the multifunction button and volume+ button for 3 seconds. Audrey says “multipoint enabled.”
  4. Open your first device’s Bluetooth® menu and select “Aeropex by AfterShokz.” Audrey says “connected”.
  5. Turn your headphones off.
  6. Re-enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
  7. Open your second device’s Bluetooth® menu and select “Aeropex by AfterShokz.” Audrey says “connected.”
  8. Turn your headphones off.
  9. Turn your headphones on. Your headphones are now connected to both devices.
  10. To turn multipoint pairing off: Press and hold the multifunction button and volume button for 3 seconds. Audrey says “multipoint disabled.”
    More information: bit.ly/ASMultipoint

Moisture Detected Alert
These headphones can detect liquid such as water, sweat, and rain. If the headphones are plugged into the charger while wet, the LED indicator will flash red and blue. The headphones will also vibrate and emit a beep. If this happens, remove the charging cable from the headphones, dry them completely and then proceed with charging.

How to Reset Your Headphones

  1. Start with your headphones powered off.
  2. Enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
  3. Press and hold the multifunction button, volume+ button and volume- button (all three buttons) simultaneously for 3-5 seconds, until you hear two beeps or feel vibrations.
  4. Turn your headphones off. Aeropex is now reset and can be re-paired to your device.

Optional Accessories

Earplugs (D)

Use with headphones in environments where it is safe to block out ambient noise, such as on a train or airplane.

  1. Roll earplugs firmly between fingers and place in ears.
  2. While music is playing to adjust EQ settings to reduce or enhance bass while wearing earplugs, press and hold volume+ and volume- buttons simultaneously.
  3. Switch EQ to original setting when you take out the earplugs.

Manufacturer

AfterShokz LLC 6057 Corporate Dr., East Syracuse, NY 13057

Let us take care of you! We’ve got your back against defects. Register your Aeropex at register.aftershokz.com