Bestway 58486 Flowclear Sand Filter Pump
Bestway 58486 Flowclear Sand Filter Pump
58486 Hmax 1.5 m
OWNER’S MANUAL
bestwaycorp.com/support
Visit Bestway YouTube channel
SAFETY INSTRUCTIONS
WARNING
IMPORTANT SAFETY INSTRUCTIONS – READ AND FOLLOW ALL SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:
- The pump is to be supplied by an isolating transformer or supplied through a residual current device (RCD)having a rated residual operating current not exceeding 30 mA.
- The power source on the wall of the building should keep more than 4m away from the pool.
- The appliance must be supplied by the earthed power source.
- RISK OF ELECTRIC SHOCK – The pump cannot be used while people are inside the pool. Forbid the access of the pool in case of damage to the sand filter.
- DO NOT BURY THE CORD. Locate cord to minimize abuse from lawnmowers, hedge trimmers, and other equipment.
- To reduce the risk of electric shock, replace the damaged cord immediately.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
- Extension cords can’t be used.
- Risk of electric shock. Using the sand filter with an unmatched electrical supply is dangerous and will permanently damage the sand filter.
- Do not remove the grounding prong or modify the plugin anyway. Do not use adaptor plugs. Consult a qualified electrician for any questions relating to the validity of your plugs or grounding.
- Handle the sand filter with care. Do not pull or carry the sand filter by the power cord. Never pull a plug from the outlet by yanking the power cord. Keep cord free from abrasions. Sharp objects, oil, moving parts, and heat should never be exposed to the sand filter.
- Always unplug this product from the electrical outlet before removing, cleaning, servicing, or making any adjustment to the product.
- Don’t plug or unplug the appliance if the hand is wet.
- Always unplug the appliance:
- On raining days
- Before cleaning or other maintenance
- Leave it unattended on holidays
- When the appliance will be not used for a long time, such as in the winter, the pool set should be disassembled and stored indoors.
CAUTION: Read the instruction before using the appliance and installation/reassembly every time. - Safekeeping the instruction. For reconstruction of the pool set every time, please always refer to the instructions.
- If the instruction is missed, please contact Bestway or search it in the website: www.bestwaycorp.com
- Electric installations should follow national wiring rules. Consult a qualified electrician for any questions.
CAUTION:
This sand filter is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage. - This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- Cleaning and user maintenance must be performed by an adult above 18 years old who is familiar with the risk of electric shock.
NOTES: - Place the sand filter on solid, level ground. Ensure the sand filter is at least 3.5 meters away from the poolside. Keep distance as far as possible.
- Pay attention to position pool and sand filter so adequate ventilation, drainage, and access for maintenance are available. Never place the filter in an area that may accumulate water, or on a walking path with lots of foot traffic.
- It is necessary to have the plug accessible after the installation of the pool. The plug of the sand filter shall be at least 3.5m away from the pool. POOL
- Atmospheric conditions may affect the performance and life span of the sand filter; take adequate precautions to protect the sand filter from unnecessary wear and tear that may occur during periods of cold or hot weather and/or exposure to the sun.
- Please examine and verify all sand filter components are present before use. Notify Bestway at the customer service address listed on this manual for any damaged or missing parts at the time of purchase.
- It is imperative to change as soon as possible all deteriorated parts. Only use parts approved by the manufacturer.
- Do not allow children or adults to lean or sit on the apparatus.
- Do not add chemicals to the sand filter.
- When chemical products are used to clean the pool water, it is recommended to respect a minimum filtration time to preserve the health of swimmers which depends on the compliance of health regulations.
- Only the media provided or specified by the manufacturer is to be used with product installation.
- It is essential to check that the suction openings are not obstructed.
- It is advisable to stop the filtration during maintenance operations on the filtration system.
- Regularly monitor the filter clogging level.
- A weekly check is recommended for backwashing or cleaning. Minimum daily filtration operating time of 8 hours is recommended to ensure clear pool water.
- It is essential to change any damaged element or set of elements as soon as possible. Use only parts approved by the person responsible for placing the product on the market.
- All filters and filter media shall be inspected regularly to ensure that there is not a build-up of detritus thus preventing good filtration. The disposal of any used filter media should also be in accordance with applicable regulations/legislation.
- Mind all the safety requirements and recommendations described in the manual. In case of doubt on the pump or any circulation devices, contact a qualified installer, or the manufacturer/importer/distributor. The water circulation installation shall comply with the European as well as national/local regulations, especially when dealing with electrical issues. Any change of valve position, pump size, grille size can cause a change of the flow and the suction velocity can be increased.
- This product is not intended for commercial use.
PLEASE READ THE INSTRUCTION MANUAL CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
SAVE THESE INSTRUCTIONS
RCD WARNING
WARNING: Before inserting the plug into a power outlet, make sure the current rate of the power outlet is suitable for the sand filter.
WARNING: Risk of electric shock. The RCD plug must be tested before each use.
WARNING: Insert the RCD plug into a residual current device (RCD) having a rated residual operating not exceeding 30 mm.
WARNING: Do not use the sand filter if this test fails. For assistance, please visit the support section on our website, www.bestwaycorp.com.
PUMP DISPOSAL
Meaning of crossed-out wheeled dustbin:
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
SPECIFICATIONS
 |
Filter Diameter: | 480 mm |
| Effective Filter Area: | 0.181 m2 (1.95 ft 2) | |
| Max. Operating Pressure: | 1.59 Bar (23 PSI) | |
| Working sand filter pressure: | <0.55 Bar (8 PSI) | |
| Max. Water Temperature: | 35°C | |
| Sand: | Not included | |
| Sand Size: | #20 silica sand,0.45-0.85 mm | |
| Sand Capacity: | Approximately 55 kg |
PARTS REFERENCE OVERVIEW
Before assembling the sand filter, take a few minutes to become familiar with all the sand filter parts.
| REF.NO | SPARE PART NO. | A |
| 1 | P61138ASS16 | 1 |
| 2 | P03832 | 2 |
| 3 | P61209ASS16 | 1 |
| 4 | P03819 | 1 |
| 5 | P03820 | 1 |
| 6 | P61211ASS16 | 1 |
| 7 | P6581ASS16 | 1 |
| 8 | P6580ASS16 | 1 |
| 9 | P03818 | 1 |
| 10 | P6614ASS16 | 1 |
| 11 | P6029ASS16 | 5 |
| 12 | P03830 | 1 |
| 13 | P61214ASS16 | 1 |
| 14 | P61210ASS16 | 8 |
| 15 | P03829 | 1 |
| 16 | P6916ASS16 | 2 |
| 17 | P6124ASS16 | 2 |
| 19 | P6561ASS16 | 1 |
| 20 | P6562ASS16 | 1 |
| 21 | P6563ASS16 | 1 |
| 22 | P03815 | 1 |
| 23 | P03849 | 1 |
| 24 | P6028FRASS16 | 2 |
| 25 | SPARE PART NO. | A |
| 26 | P61322ASS16 | 1 |
| 27 | P61318ASS16 | 1 |
ASSEMBLY
(You will need a screwdriver.)
- Carefully remove all components from the package and check to ensure nothing is damaged. If equipment is damaged, immediately notify the retailer from where the equipment was purchased.
- The sand filter should be placed on solid, level ground, preferably a concrete slab. Position the sand filter so the Ports and Control Valve are accessible for operation, servicing, and winterizing.
- EN60335-2-41 TEST standard requires the sand filter must be vertically fixed on the ground or a certain pedestal made of wood or concrete before use to prevent the sand filter from accidental falling. A fully assembled sand filter will exceed 18 kg. The mounting holes should be 8 mm in diameter and spaced 86 mm apart. Use two bolts and nuts with a maximum of 8 mm in diameter to fasten the sand filter to the pedestal.
LOAD POOL-GRADE FILTER SAND/FLOWCLEAR™ POLY SPHERE.
NOTE: Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85 mm, approximately one 55 kg bag should suffice. If you do not use the recommended size of filter sand, filtering performance will be reduced and the sand filter may be damaged, thereby voiding the warranty.
NOTE: To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the Skimmer on the Hub.
NOTE: Sand/Flowclear™ Polysphere not included.
NOTE: Use 28 g (0.06 lbs) Flowclear™ Polysphere to replace 1 kg (2.20 lbs) sand.
CONNECT TO THE POOL
FOR POOL WITH 32 MM VALVES
STOP
Before switching on, please read the manual carefully.
RCD TEST
OPERATION
TIMER
- Plug into a power source, adjust the power switch to the “ON” (-) position. The sand filter will begin working immediately.
- Adjust power switch to “OFF” (0) position. The sand filter will stop working immediately.
- After turning it on, you can adjust work time, rest time, and cycle time by turning the knob to the desired position. See the table below for more details.
- When the timer knob is moved into a new position, the filter’s previous cycle automatically cancels so a new cycle can begin.
- Each time the filter is powered on or restarted, a new cycle will begin based on the timer knob position.
NOTE: If the knob is adjusted to the 24-hour position (24), the sand filter will work continuously without any rest period.
| Knob Position | Working time(H) | Rest time(H) | Cycle period(H) |
| 4 | 4 | 20 | 24 |
| 6 | 6 | 18 | 24 |
| 8 | 8 | 16 | 24 |
| 10 | 10 | 14 | 24 |
| 12 | 12 | 12 | 24 |
| 24 | 24 | 0 | 24 |
| P4 | 4 | 4 | 8 |
| P6 | 6 | 6 | 12 |
| P8 | 8 | 8 | 16 |
CONTROL VALVE OVERVIEW
WARNING: To prevent equipment damage and possible injury, always switch off the sand filter before changing the Control Valve function. Changing valve positions while the pump is running can damage the Control Valve, which may cause personal injury or property damage. How to Use the Control Valve: Press down on the Control Valve handle and rotate to the desired function.
| Filter: This function is used to filter pool water and should be positioned here 99% of the time. Water is pumped through the sand filter, where it is cleaned and returned to the pool. |
Closed: This function stops water flowing between the sand filter and the pool. |
 |
|
| Backwash: This function is used to clean the sand bed; water is pumped down through the Collector Hub, upwards through the sand bed, and deposited out of Port D. |
Rinse This function for initial startup, cleaning, and sand bed leveling after Backwash; water is pumped downwards through the sand bed, up through the Collector Hub and deposited out of the valve Port D. |
 |
|
| Drain: This function drains water from the pool; another filter bypass setting, water is pumped and deposited out of Port D, instead of returning it to the pool. | Circulate: This function circulates pool water bypassing the sand filter; use this function if the filter is broken to collect debris in the Debris Screens. |
 |
|
NOTE:
- Be sure all provisions for wastewater disposal meet applicable local, state, or national codes. Do not discharge water where it will cause flooding or damage.
- When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the Control Valve.
- Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
- Do not set the Control Valve between two functions, or it will lead to leaking.
- To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the filter or circulate function.
AIR RELEASE
Press down the control valve handle and wait until the water flow from Port D to release the air.
NOTE: It is important to repeat this operation every time you start the pump after winterizing, maintenance, and backwashing the sand bed.
FIRST TIME USE INSTRUCTIONS
Backwash and Rinsing must be performed to prepare the pump for its first use and to wash the sand.
CAUTION: DO NOT DRY RUN THE SAND FILTER
- Press down on the Control Valve handle and rotate to the Backwash function.
- Plugin and run the sand filter for 3-5 minutes, or until the water runs clear.
- Switch off the sand filter and set the Control Valve to the Rinse function.
- Switch on the sand filter and run the sand filter for 1 min. This circulates water backward through the sand filter and drains water out of Port D.
- Switch off the sand filter. Set the Control Valve to the Closed function.
- Top up pool water if required.
IMPORTANT: This procedure removes water from the pool, which you’ll need to replace. Switch off the sand filter immediately if water levels near the pool’s Inlet and Outlet valves.
- Now the sand filter is ready for use. Set the Control Valve to the Filter function.
NOTE: To prevent the risk of electrical shock dry any excess water from yourself and the sand filter.
IMPORTANT: Before the operation, make sure the tank is placed steadily on its base and connected correctly to the pump. - Switch on the sand filter to run it.
NOTE: The sand filter has now started its filtering cycle. Check that water is returning to the pool and take note of the filter pressure on the Pressure Gauge. Generally, the recommended sand filter pressure is less than 0.56 Bar (8.0 PSI) when it is running.
SAND FILTER MAINTENANCE
CAUTION: You must ensure the sand filter is switched off and unplugged before any maintenance begins or severe risk of injury or death exists. As dirt builds up in the sand filter, the pressure reading on the Pressure Gauge will increase. When the Pressure Gauge is 0.62 Bar (9.0 PSI) or higher, or water flow to the pool is too low, it is time to clean the sand. To clean the sand bed, follow all instructions outlined previously in Backwash and rinsing.
NOTE:
- The Pressure Gauge is just used for measuring the water pressure, not used for precision measurement.
- We recommend you clean the sand bed once a month or less regularly depending on how often the pool is used. Do not clean the sand too frequently.
CLEANING THE STRAINER
- Switch off the sand filter and set the Control Valve to the Closed function.
- Close the connection valves.
- Remove the Strainer Cover by unscrewing it.
- Take out the Strainer, remove any debris.
- Put the Strainer back into position. Ensure the hole in the strainer is aligned.
- Ensure the Seal Ring is in place. Secure the Strainer Cover back.
- Open the connection valves.
NOTE: The Strainer must be emptied and cleaned periodically. A dirty or blocked strainer will reduce the performance of the sand filter.
LOWERING OR DRAINING POOL WATER
- Switch off the sand filter and set Control Valve to the Drain function.
- Detach the Hose from the pool’s Port A and sand filter Port A and attach to Port D.
- Switch on the sand filter and press the “RESET” button to run the filter and remove the pool water.
WARNING: DO NOT DRY RUN THE SAND FILTER.
STORAGE
In areas that have freezing winter temperatures, pool equipment must be winterized to protect against damage. Allowing water to freeze will damage the sand filter and void the warranty.
- Backwash the sand filter.
- Drain the pool according to the pool owner’s manual.
- Unscrew the drain valve cap at the bottom of the tank and release the remaining water.
- Disconnect the two Hoses from the pool and the sand filter.
- Completely spill the sand out of the tank and dry all components.
- Move away the sand filter from the pool area, store the sand filter in a dry indoor location out of the child’s reach.
TROUBLESHOOTING
| Problems | Probable Causes | Solutions |
| Sand is flowing to the pool |
– Sand is too small – Move the control valve from the backwash to the filter function without stopping the sand filter – The level of the sand is too high – The skimmer is broken |
– Recommend 0.45 mm to 0.85 mm #20 silica sand – Stop the sand filter every time set the control valve – Check if the level of the sand is between the marked “MAX” and ” MIN” on the collector hub – Replace the skimmer |
| No water flow | – Stopper plugs were not removed – Air was not released – The control valve is set to Close – The strainer is blocked – Sand filter broken |
– Remove the stopper plugs and insert the debris screens – Release the air – Set to filter function – Clean the strainer – Call for service |
| Excessive filter pressure |
– Dirty filter – Calcified sand bed – Insufficient backwashing – The pressure gauge is broken |
– Backwash – Inspect sand and change if necessary – Backwash until water runs clear – Replace the pressure gauge |
| Control Valve leaks from the port D |
– Control Valve is set between two functions – The gasket is broken |
– Set to one function – Replace the gasket |
| Connectors leak | – Washer of the connectors is not in place – Washer of the connectors broken – Loose Hoses |
– Reposition the washer – Replace the washer – Tighten the |
©2021 Bestway Inflatables & Material Corp.
Bestway Inflatables & Material Corp., Shanghai, China
Bestway (Europe) S.r.l., Via Resistenza, 5, 20098 San Giuliano Milanese (Milano), Italy
Bestway (USA) Inc., 3411 E. Harbour Drive, Phoenix, Arizona 85034, United States of America
Bestway Central & South America Ltda, Salar Ascotan 1282, Parque Enea, Pudahuel, Santiago, Chile
Distributed in Australia & New Zealand by Bestway Australia Pty Ltd, Unit 2/98-104 Carnarvon St Silverwater, NSW 2128, Australia
Tel: Australia: (+61) 29 0371 388; New Zealand: 0800 142 101
Distributed in the United Kingdom by Bestway Corp UK Ltd. 8 Wentworth Road, Heathfield Industrial Estate, Newton Abbot, Devon, TQ12 6TL
Bestway (Hong Kong) International Ltd./Bestway Enterprise Company Limited
Suite 713, 7/Floor, East Wing, Tsim Sha Tsui Centre, 66 Mody Road, Kowloon, Hong Kong
FAQs
What is Power Suggestion?
Normally this is caused by an electrical issue. Please ensure that the filter pump is plugged directly into the mains socket and not an extension lead. We recommend also checking the socket with other items to ensure this is not an issue with the socket itself.
What do we face water flow issues?
Step 1 – Make sure hoses are clear from any blockages and water is not being restricted by tight connections.
Step 2 – Make sure the stopper caps have been removed and ensure the debris screens are clear.
Step 3 – Check the filter cartridges in the pump are clean or replace them.
Step 4 – Purge any air from the pump pipes which could be preventing a waterflow.
What do leaking water from the top of the pump unit?
If this issue occurs this means the seal is not aligned correctly. Check the placement of the seal to ensure this is in the correct place.
Who to setup noisy filter pump
Step 1 – Check for air trapped in the pump.
Perform air purge operation which removes the build up of air that should not be there from the pipes.
Open/unscrew the Air Purge Valve on the top of the Filter Pump; air is released as water fills the Filter Pump.
When water comes out of the Air Purge Valve screw it closed and wipe away any water.
To start the Filter Pump, insert the plug.
Step 2 – Check if the filter cartridge is dirty
The filter cartridge in the pump may need to be cleaned or replaced.
Who to fix leaking water from the top ring
Step 1 – Check filter cartridge is correct size
Check the size of the filter cartridge being used and replace with correct size. The size you need should be on the box the pool arrived in.
Step 2 – Check filter cartridge is positioned correctly
Check the position of the filter cartridge and align if necessary.
Step 3 – Check the filter cap seal is aligned incorrectly
Check the position of the filter cap seal and realign if necessary.
Step 4 – Check if the filter cap seal is damaged
Who to fix leaking water from purge valve
Step 1 – Check if the purge valve is missing.
Step 2 – Check if the purge valve is loose.
If it is we recommend tightening the purge valve.
Step 3 – Check if the cap seal is damaged.
Who to fix Leaking water from hose connections
Step 1 – Check if the hose seal ring is missing.
Step 2 – The clamp is not tightened correctly.
If it is we recommend tightening the clamp correctly.
Who to Change water if Pool water is dirty?
Step 1 – Check if the filter cartridge is dirty
If it is clean the filter cartridge. If this isn’t possible replace the filter cartridge. This will need to be replaced every 14 days/ uses.
Step 2 – Is the filter pump smaller than the one required for your pool?
If this is the case the pump will not be cleaning your pool correctly. We always recommend checking the compatibility of pools and filter pumps.
Step 3 – Is the operating time of the filter pump under 10 hours a day?
If this is the case we recommend increasing the operating time of the filter pump.
Step 4 – Purchase some chemicals
We recommend purchasing some chemicals to support the use of your filter pump. If you need further chemical advice we recommend checking our chemical guide here.
Video
www.bestwaycorp.com
For support please visit us at:
bestwaycorp.com/support
