Energizer Smart wifi. Video doorbell
Installation Guide

Thank you for choosing the Energizer® Smart Video Doorbell. This installation guide will help you with installing your device with your existing doorbell power wires and mechanical chime.

Note: Please follow the app setup steps in the Quick Start Guide BEFORE installing your device.
Not compatible with digital chimes.

System Requirements:
• Requires a working wired doorbell
• 16-24V AC 10VA transformer voltage
• WiFi router with an interent connection
• WiFi 2.4GHz 802.11n
• Android 7.0 or higher/ iOS 11 or higher
• Energizer. Connect App (on mobile devices)

©2021 Energizer. Energizer and certain graphic designs are trademarks of Energizer Brands, LLC and related subsidiaries and are used under license by Jem Connected IOT, Inc. All other brand names are trademarks of their respective owners. Neither Jem Connected IOT, Inc. nor Energizer Brands, LLC is affiliated with the respective owners of their trademarks.

Step 1
First, ring your doorbell to locate your mechanical chime. Turn off the power breaker at your fuse box for your existing doorbell and mechanical chime. Ring your doorbell again to confirm it’s now off.

NOTE: Your doorbell circut breaker might be unlabled. Try ringing your doorbell to make sure it’s off.

Step 2
Outside at your door, remove the old working doorbell and disconnect the two existing wires from the unit.

NOTE: It is recommended to clean the wires
to be free of any corrosion.

Step 3
Based on your door and entry way, choose either the flat mounting bracket or wedge+flat mounting brackets for an angled view and install it around the wires.

Step 4
Option 1: Mounting Flat Bracket
Use the long screws to mount on the wall.

NOTE: Make sure the bracket shows the arrow facing up and the pre-installed foam backing is against the wall.

NOTE: Make sure to screw the bracket very tightly against the wall to prevent water from touching your wires.

Step 5
Option 2: Mounting Wedge+Flat Bracket (for angeled view)
A) Take the wedge (angled) bracket and position left or right for best viewing angle. Use the long screws to mount to wall.

NOTE: There are two holes, the one that allows you to view the wall is the correct one to drill through. (See image A)

B) Next, take the flat bracket, with arrow facing up, and screw it into the mounted wedge bracket using the short screws.

Step 6
Connect the two wires to the screw terminals on the back of your doorbell.

NOTE: If using a microSD card (not included), install prior to mounting doorbell.

NOTE: It does not matter which wire goes to
which screw terminal, just make sure they are secure.

NOTE: If the wires coming out from your home are too short you can use the included wire crimp extenders.

Step 7
Install the doorbell into the mounting bracket at the top first and then press and hold the bottom in.

Step 8
Lastly, make sure to secure the doorbell with the included security screw and tool.

Step 9
Next, find your mechanical chime and remove the cover and batteries (if applicable).

Step 10
Take the power kit included with your doorbell. Notice there is one main wire that splits into two.

Step 11
Slightly unscrew both screw terminals and slip one hook from the power kit under each screw. Make sure that the wires already on the chime stay connected too.

NOTE: It does not matter which color wire
from the power kit connects to which screw.

Step 12
Using the included double sided tape, affix the power kit to your chime wherever there is space and replace the cover.

Step 13
Turn the doorbell power back on at the fuse box. The light on the doorbell button should tum on and after a few minutes become solid blue.

Enter the Energizer®. Connect App and select the doorbell to choose the appropriate chime and finalize setup. Your Smart Video Doorbell is now ready for use!

Troubleshooting

Questions or Comments?
Visit our FAQ at www.energizerconnect.com

Doorbell:
If the light on your doorbell button does not illuminate and the Energizer® Connect App cannot locate the product:

1. Check that the power has been restored at the fuse box.
2. Check that the wire connections at the screw terminals are secure. Remember to turn the power off before and back on after.

Notice

Chime:
Not all home setups require the power kit to be installed. If after fully installing and setting up your doorbell, you find that everything works except for the mechanical chime:

1. First make sure to check the “CHIME SETTINGS” in the Energizer® Connect App and ensure “MECHANICAL CHIME” is selected.
2. Make sure the power kit and cables are not interfering with the movement of the mechanical chime.
3. If your mechanical chime is still not working, try removing the power kit from the chime. Remember to turn the power off before, and back on after, and then select “MECHANICAL CHIME” again in the app once the doorbell turns back on.
4. If the issue is not resolved, use the included wireless chime and select “WIRELESS CHIME” in the app.

EWL4-1001-WHT
V1.1

Thank you for choosing the Energizer® Smart Water Leak Sensor. This quick start guide will help you with setup and installation.

Package Includes

1 – Smart Water Sensor
1 – Quick Start Guide
1 – Double Sided Mounting Tape
1 – Mounting Screws & Anchors

Note: Energizer® Connect devices only work on a 2.4ghz WiFi network.

©2019 Energizer. Energizer and certain graphic designs are trademarks of Energizer Brands, LLC and related subsidiaries and are used under license by Jem Connected IOT, Inc. All other brand names are trademarks of their respective owners. Neither Jem Connected IOT, Inc. nor Energizer Brands, LLC is affiliated with the respective owners of their trademarks.

Pair the Smart Water Leak Sensor

1. Download the Energizer® Connect app from theApp Store (for iPhones) or Google PlayStore (forAndroid phones).
   Before opening the app, make sure your phone is connected to the WiFi network that your SmartWater Leak Sensor will be placed on.
   
2. Open the app and create an account by following the on-screen instructions.
   
3. Remove back cover by turning counter clockwise.
   Insert 2 AAA batteries (not included).
   
   Note: The indicator light on the sensor should start blinking rapidly (about 4 times per second) for EZ pairing mode.
   EZMODE: Rapidly blinking (about 4times per second)
   APMODE: Slowly blinking (about 2 times per second)
4. After logging in, click “+” on the top right of the screen and select “Add Device”.
   
5. Select “Water Leak Sensor”.
   
6. Confirm that the indicator light is rapidly blinking, then click next.
   
7. Confirm that the networkWiFi displayed is your 2.4ghz WiFi network, enter your WiFi password and click confirm.
   
8. Your Smart Water Leak Sensor will now be connected to the network. Confirm the settings for your device and then click Finish Device Setup.
   
9. Installation Steps:
   

Troubleshooting

If you need to reset or troubleshoot your sensor, simply hold down on the power/reset button for 5-10 seconds.

Pairing Modes:

EZ mode: The device’s indicator light is rapidly blinking for easy, quick pairing setup.

AP Mode: Access Point mode is a secondary setup process in which the device’s indicator light is slowly blinking and requires multiple steps for pairing. Follow the on-screen step by step instructions.

Notice

FCC Compliance

This device complies with Part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement

To satisfy FCC’s RF exposure requirements, a separation distance of20 cm or more should be maintained between the antenna of this device and persons during device operation.

To ensure compliance, operations at closer than this distance is not recommended.