FRIGIDAIRE IM117000 Automatic Ice Maker Manual

FRIGIDAIRE IM117000 Automatic Ice Maker

Instruction

An authorized service technician is recommended to install the ice maker kit.

WARNING

To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator.
Connect the ice maker to a potable water supply only.

NOTE
Check with your local building authority for recommendations on water lines and associated materials prior to installing your new refrigerator. For household water line hookup from the home water supply system to the unit, Frigidaire recommends for homes with existing valves its Smart Choice® water line kit 5304437642 (with a 6 Stainless Steel Water Line) and for homes without an existing valve, Frigidaire recommends its Smart Choice® water line kit 5304493869 (with a 6 Polyline Waterline). Please refer to www.frigidaire.com for more information.

Tools Needed:
Flathead screwdriver	Phillips or Quadrex driver
1/4″ Hex driver	Gloves
Drill	Needle nose pliers

Ice Maker (IM117000) Kit Components

Parts needed for install inside the unit

Parts needed for install on the backside of the unit

Ice Maker Installation Instructions

Unplug the refrigerator from the electrical outlet. 2. Lift the freezer shelf up and out. Set aside.
Lift the freezer shelf up and out. Set aside.
Remove the water inlet and electrical cover, located on the inside of the unit, by inserting a flathead screwdriver on the left side of the opening in the small cover. Push to the right to disengage the snap.
Locate dimples in the freezer liner for screw placement (a flashlight may help). Align the shoulder screws with the dimples. Push the screws to penetrate the freezer liner and drive the screws in until they are tight against the liner. Use 2 screws on the left side wall, and 3 on the top of the liner.
For a 30″ wide refrigerator install the bracket onto the ice maker. The Ice maker will slide onto the mounting features on the bracket and snap into place. The locking feature is located on the rear of the ice maker.
Plug the ice maker in the electrical connector on the back wall.
Make sure the ice maker water channel is under the water fill tube, and then slide the ice maker onto the 2 sidewall shoulder screws. The ice maker will snap into place.
Install the plastic shutter into the window in the front of the cover. The shutter snaps into the clips on the inside face of the cover, no tools are required. Slide the ice maker cover onto the shoulder screws on top of the unit until it locks into place with a snap.
To install the ice bin, the freezer shelf needs to be in the lowest position. Slide the ice bin between the sidewall and the right side of the ice maker housing positioned on the shelf.
Locate the Ice maker installation label on the rear outside right top corner of the refrigerator. Cut the label on the dashed lines, and push flaps inward until they stick to the unit.
Install the waterline by screwing the nut on the end of the tube onto the water inlet. Tighten the nut until snug, and then tighten an additional ¼ turn with needle-nose pliers. (See A.)
Install the 2 water line clips on the unit evenly spaced inside the depressed area located under the water inlet. Insert the water line tube into the clips. (See B.)

*If you have a unit with an access cover, continue to page 4 for additional installation instructions. For a unit without an access cover, continue

CAUTION
Wear gloves and use extreme CAUTION when handling the access cover.
Remove 8 screws from the access cover located at the bottom rear outside of the unit. Set aside.
Place the green water tube to the icemaker into the bottom outlet of the water valve. The tube must be pushed into the valve up to the black line marked on the tube. Check to make sure the tube is installed correctly.
The water valve location has pre-made holes on the right rear of the unit. The water line should be oriented downward when the valve is installed. Install the water valve using a ¼” hex head driver, install the 2 hex head screws. Tighten screws until they are snug and then tighten an additional ¼ turn.
Plug connector on water valve wire harness into the connector above the condenser coil. Install the water valve clip at the bottom right side of the unit, and route and attach the water valve harness into the clip.
Reinstall the access cover by hooking the cover onto the bottom flange of the cabinet, and then tilt the cover upward to align with the screw locations on the cabinet. Install the screws starting with the 2 on the left side, then the right side, finish with the center screws.
NOTE
Ensure the power cord is aligned with the notch at the bottom of the access cover and the water line is located inside the notch at the top right of the cover.
Connect the household water line to the water valve. Follow instructions in Connecting Ice Maker to Water Supply.
Remove the connector box from the unit with a Philips screwdriver. Discard screw.
Open the connector box using a flat head screwdriver. Insert at the notched point and turn. Insert the water valve in the hole in the box.
Connect the valve wire harness with the white connector from the unit. Insert the wiring in the box as shown. Close the box cover completely, ensuring all wiring is inside.
Plug the green water tube from the icemaker into the bottom outlet of the water valve. The tube should be pushed into the valve up to the black line marked on the tube.
Attach the water valve bracket to the unit at the 2 pre-made holes using the 2 screws included in the kit.
Connect the household water line to the water valve fitting (pointed up). Follow instructions in Connecting Ice Maker to Water Supply.

Connecting Ice Maker to Water Supply

WARNING
To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator.
CAUTION
To Avoid Property Damage:

Stainless Steel braided tubing is recommended
for the water supply line. Water supply tubing made of ¼” plastic is not recommended to be used. Plastic tubing greatly increases the potential for water leaks, and the manufacturer will not be responsible for any damage.
DO NOT install water supply tubing in areas where temperatures fall below freezing.
Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft water, ensure that the softener is maintained and working properly.

IMPORTANT
Ensure that your water supply line connections comply with all local plumbing codes.
Before Installing The Water Supply Line, You Will Need:

Basic Tools: adjustable wrench, flat-blade screwdriver, and Phillips screwdriver
Access to a household cold water line with water pressure between 30 and 100 psi.
A water supply line preferably made of Braided
Stainless Steel or Braided Poly with integral fittings for connection to the refrigerator and the valve at the wall. If the home has a ¼” copper line, and the owner prefers to keep the copper line, a compression fitting ferrule (sleeve) and nut should be replaced each time the fitting is reused.

NOTE
Check with your local building authority for recommendations on water lines and associated materials prior to installing your new refrigerator. Depending on your local/state building codes, Frigidaire recommends for homes with existing valves its Smart Choice® water line kit 5304437642 (with a 6 ft. Stainless Steel Water Line) and for homes without an existing valve, Frigidaire recommends its Smart Choice® water line kit 5304493869 (with a 6′ Polyline Waterline). Please refer to www.frigidaire.com.
NOTE
Water lines should be long enough to allow the refrigerator to roll forward for cleaning or service. Typically, 6 ft. length works well for braided Stainless or Poly kits. A ¼” copper line should be longer to coil extra length behind the refrigerator so movement will not kink the copper line.

Connecting Ice Maker to Water Supply

To Connect Water Supply Line To Ice Maker Inlet Valve

Disconnect refrigerator from an electrical power source.
Place the end of the water supply line into the sink or a bucket.
Turn ON the water supply and flush the supply line until the water is clear.
Turn OFF the water supply at the shutoff valve.
Remove the plastic cap from the water valve inlet and discard the cap.
If you use copper tubing, slide the brass compression nut and then ferrule (sleeve) onto the water supply line.
Push the water supply line into the water valve inlet as far as it will go (¼ in. / 6.4 mm). Slide the ferrule (sleeve) into the valve inlet and finger tighten the compression nut onto the valve.
Tighten another ½ turn with a wrench; DO NOT overtighten. See below.
Secure the copper line to the clamp (as shown), using the existing screw.
If you use braided flexible stainless steel tubing, the nut is already assembled on the tubing. Slide the nut onto the valve inlet and finger tighten the nut onto the valve. Tighten another ½ turn with a wrench; DO NOT overtighten. See below.
With the steel clamp and the screw, secure the water supply line to the rear panel of the refrigerator as shown.
To turn the ice maker on, press the ice maker’s On/ Off power switch so the LED is steadily illuminated.
Turn ON the water supply at the shutoff valve and tighten any connections that leak.
Reconnect the refrigerator to an electrical power source.

Ice Service

If your refrigerator has an automatic icemaker, minimal ice will be produced during the first 24 hours of operation. Air in new plumbing lines may cause the ice maker to cycle 2 or 3 times before making a full tray of ice. With no usage, it will take approximately 1 to 2 days to fill the ice bin.
New plumbing connections may cause the first production of ice cubes to be discolored or have an odd flavor. Discard ice made during the first 24 hours.
Turning Your Ice Maker On
After the plumbing connections have been completed, the water supply valve must be opened. Place the ice bin under the ice maker, pushing it as far back as possible. Press the ice maker’s On/Off button. The button will illuminate in green when the ice maker is On.
Turning Your Ice Maker Off
To stop the ice maker, press the ice makers On/Off button. The ice maker also stops producing ice automatically when the bin is full, and then it resumes when the level in the bin drops.
IMPORTANT
To ensure proper function for your ice maker, hook up the water supply immediately or turn the ice maker OFF. If the ice maker is on and the water supply is not connected, the water valve can make a loud chattering noise.
Ice Production: What To Expect
The ice maker will produce about 2 pounds of ice every 24 hours depending on usage conditions.
Note: You can make more ice by setting the freezer to a colder setting. Ice is produced at a rate of 10 cubes every 100 to 160 minutes.
CAUTION
Do Not place the ice container in your dishwasher.
Ice Maker Tips
Remember that water quality determines your ice quality. If the water source uses a water softener, ensure that the softener is maintained and working properly. Chemicals from a malfunctioning softener can damage the ice maker.
CAUTION
Do Not place the ice container in your dishwasher.

Wash the ice container in warm water with mild detergent. Rinse well and dry.
Stop the ice maker when cleaning the freezer or for short vacations.
If the ice maker will be turned off for a long period of time, turn the water supply valve to the closed position.

DOWNLOAD RESOURCES

FRIGIDAIRE IM117000 Automatic Ice Maker [pdf] Instruction Manual IM117000, Automatic Ice Maker
Read more: https://manuals.plus/frigidaire/im117000-automatic-ice-maker-manual#ixzz7e2ubwjBk

FAQ’S

What is the purpose of the water filter?

The water filter is a sediment filter that reduces particulates in the water. It also reduces chlorine taste and odor. The filter may be cleaned and reused.

Do I need to install a water filter?

If you have hard water, it is recommended that you install a water filter.

What is the purpose of the ice maker shutoff arm?

The ice maker shutoff arm is used to turn off the ice maker when not in use.

How do I know if my refrigerator has a hot gas valve or a cold gas valve?

If your refrigerator has a hot gas valve, it will have an exhaust vent on the back wall of your refrigerator compartment. If your refrigerator does not have an exhaust vent, it has a cold gas valve.

Does the Frigidaire ice maker turn off automatically?

To stop the ice maker, simply lift the wire signal arm until it clicks and locks in the “up” or OFF position. Keep in mind the ice maker will also turn off automatically when the ice container/bin is full.

Why is my automatic ice maker not working?

If your ice maker isn’t producing ice at all or is producing crescents or cubes that are smaller than usual, it’s typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.

How do you reset a Frigidaire ice maker?

The reset button on a Frigidaire ice maker is usually located behind the control panel. To access it, you will need to remove the control panel. Once you have removed the control panel, you should be able to see the reset button. Press and hold it for 5 seconds to reset the ice maker.

How long does it take for Frigidaire ice maker to make ice?

After the refrigerator is installed and has cooled for several hours, the ice maker can produce ice within 24 hours. The ice maker will fill the ice bin from the rear. You must dispense some ice to force the ice forward in the bin. This will allow the ice bin to fill completely.

Why is my Frigidaire ice maker so slow?

The top reasons for a slow ice maker inside of a freezer are incorrect temperature setting, too much or too little food inside, and a clogged water line or filter.

What does quick ice mean on Frigidaire?

The Quick Ice feature is found on select dispenser model refrigerators to help speed up the production of ice. When the Quick Ice button is pressed on the dispenser control, a fan will blow over the icemaker, accelerating ice production by up to 48%.

How long does it take to make ice after changing water filter?

After replacing the water filter, it takes approximately 6 to 12 hours for the ice maker to start producing ice again. It might take longer in some cases. It is advisable to throw out the first few batches of ice from the ice maker (at least 30 ice cubes) to ensure the ice you are consuming is made from clean water.

Will a dirty water filter stop ice maker?

A clogged or incorrectly installed water filter can reduce the water flow to the ice maker and dispenser and could cause one or more of the following: Ice cubes to be thin or hollow. Odd tasting ice or water. Low ice production.

FRIGIDAIRE IM117000 Automatic Ice Maker
www://frigidaire.com/