HUANUO Monitor Desk Mount Manual

HUANUO Monitor Desk Mount Instruction Manual

Thank you for choosing this HUANUO product! At HUANUO we strive to provide you with the best quality products and services in the industry. Please share your experience of our product with others at www.huanuoav.com/reviews if you are satisfied. Should you have any issues, please don’t hesitate to contact us.

Technical Support:
1-800-556-0533 Mon-Fri 8am – 8pm (PST) (USA) (CAN)

E-mail:
[email protected] (US/CA)
[email protected] (JP)

IMPORTANT SAFETY INFORMATION

Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our customer service at [email protected].

CAUTION: Avoid potential personal injuries and property damage!

• Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
• This product contains a high pressure gas spring, fire and percussion prohibited. Also it is strictly prohibited to dismantle without professionals. Please return to the manufacturer or hand over to professional agencies if the product is abandoned.
• The desk must be capable of supporting three times the weight of the total load (the mount, the monitor and all accessories weight). Don’t use the product on particle board.

Weight Restrictions

If your monitor weighs more, this mount is NOT compatible.

WARNING
DO NOT exceed the maximum weight indicated. This mounting system is intended for use only with the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in failure of the mount and its accessories, causing possible damage and or injury.

Check the VESA Pattern of Your Monitor before You Begin the Installation

75 mm~ 3 in.
100 mm~ 4 in.

Minimum VESA pattern: 75mm/3 in.(W)x75mm/3 in.(H)

If your Monitor VESA is greater than 100×100 mm/4×4 in. or less than VESA 75x75mm/3x3in., this mount is NOT compatible.

If this desk mount is NOT compatible, please contact customer service at [email protected] to find a compatible product.

Product Features

TENSION ADJUSTMENT SHOULD BE DONE ONLY AFTER MOUNT INSTALLATION

Warning
Do not adjust tension without monitor.

1. Ensure monitor has been attached to the mount.
2. Read your monitor box or manual to find out monitor net weight.
3. Ensure the net weight of monitor (including accessories) is between
4. 4~26.4 lbs (2-12 kg).

Adjustment Sign

Warning

Tools Needed (Not Included)

Supplied Parts and Hardware

Warning :This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and und damaged or defective parts. If you require replacement parts, contact our customer service at [email protected] .

• Please note: Not all hardware included in this package will be used.

Step 1

Step 2

Step 3

Step 4

Step 5 and 7

Step 8

Install the Base

A. For Clamp Mounting

A-1 Install the USB Cable and C Clamp to the Base

A-2 Secure the Base to the Desktop

B. For Grommet Mounting

B-1 Install USB Cable and the Grommet Bolt to Base

B-2 Secure the Base to Desktop Using Locking Plate and Butterfly Nut

If there is no grommet hole on your desktop, position the base [03] on the mounting surface and mark the hole. Drill a hole using drill bit in the diameter of 3/8-1 1/16in-.(10-27mm} at the marked position through the mounting surface.

Install the Arms

Install the Monitor Plate

Attach Monitor to the ARM

Adjust Gas Spring Tension

Be sure to keep the arm in horizontal position during adjustment. Or else, it would be difficult to adjust the mount or damage the mount.

1. If the monitor can stay at the desired height by itself, no adjustment needed.
2. If the monitor rises up, press the arm to keep it in horizontal position and then use the 13/64 in.(5mm) Alley key (E) to turn the bolt clockwise(“-“direction) to reduce tension of the arm only until the monitor can stay at the desired height by itself.
3. If the monitor falls down, lift the arm to keep it in horizontal position and then use the 13/64 in.(5mm) Alley key (E) to turn the bolt counter-clockwise(“+” direction) to increase tension of the arm only until the monitor can stay at the desired height by itself.
4. Special situation: If the gas pressure is in minimum torque tension and monitor is 2kg, the monitor can not be hovered at your desired position freely and please wind the set screw(see Fig. G)) in “+” direction with the wrench “E” to fix the monitor in place.

Rotation Restriction

Tilt Adjustment

Attach The Decorative Cover to C-Clamp

Route Cables along the Arms

Thank you again for choosing this HUANUO product!

All of us at HUANUO do appreciate your product purchase. We hope that you are as happy with your product as we designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. Please share your experience of our product with others at www.huanuoav.com/reviews if you are satisfied. If you have any questions please don’t hesitate to contact us at
Technical Support:
1-800-556-0533 Mon-Fri 8am – 8pm (PST) (USA) (CAN)
Other Info:
[email protected] (US/CA)