MATTRESS FIRM RF510A Remote Control
Button Of Remote
ITEM
- Child Lock 18
Click the Child Lock button for 3 seconds to lock or unlock the remote. - Bed lamp 7
Click the bed lamp button to open or shut the light under the bed. - Antisnore 16
Click the Anti snore button, the bed moves to Anti snore position, press and hold Anti snore
button for 5s, until the backlight flashes, the control set the current position as Anti snore position - TV 15
Click the TV button, the bed moves to TV position, press and hold the TV button for 5s, until
backlight flashes and the control set the current position as the TV position. - HEAD AND FOOT UP 5
Press the head and foot up button, head and foot actuator moves out, stops when released. - HEAD AND FOOT DoWN 6
Press the head and foot down button, head and foot actuator moves in, and stops when released. - M1 20
Click the MI button, and the bed moves to the MI position, press and hold the MI button for Ss until
backlight flashes, the control set the current position as MI position - HEAD-UP 1
Press and hold the HEAD-UP button, the head actuator moves out, stops when released. - HEAD DOWN 2
Press and hold the HEAD DOWN button, the head actuator moves in, stops when released. - FOOT UP 3
Press and hold the FOOT UP button, foot actuator moves out, stops when released. - FOOT DOWN 4
Press and hold FOOT DOWN button, foot actuator moves in, stop when released. - ZG 17
Click the ZG button, and the bed moves to zero position, press and hold the zero buttons for 5s,
until the backlight flashes, the control set the current position as zero position - HEAD MASSAGE 9,10
Click the HEAD MASSAGE button, head massage motor switches massage intensity, massage
intensity switches among 0-1-2-3: - MASSAGE model 14
Click the MASSAGE MODEL button to change the massage model. - FOOT MASSAGE 11,12
Click the FOOT MASSAGE button, foot massage motor switches massage intensity, massage
intensity switches among 0-1-2-3 - MASSAGE TIME 13
Click the MASSAGE TIME button to set the massage time among 0-10-20-30mins. - FLAT 19
Click the FLAT button, the bed goes flat. - FLASHLIGHT 8
Click the FLASHLIGHT button to open and shut the Flashlight.
FCC warning
Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following two
conditions
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by doing one or more of the following measures:- Reorient or relocate the receiving antenna.
- lncrease the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected. - Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End-users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC exposure compliance requirements, please follow operation instructions as documented in this manual.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End-users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with ISED exposure compliance requirements, please follow operation instructions as documented in this manual.
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada license-exempt
RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
