Northair 26-Lb. Countertop Ice Maker HZB-12 SA Manual

26-Lb. Countertop Ice Maker User’s Manual

Item #1296908
Model #HZB-12/SA

26-Lb. Countertop
Ice Maker
User’s Manual

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic safety precautions should be followed to reduce the risk of ﬁre, electric shock, and injury to persons or property. Read all instructions before using any appliance.

DO NOT operate this or any other appliance with a damaged cord.
Connect to properly polarized outlets only. No other appliance should be plugged into the same outlet. Be sure that the plug is fully inserted into the receptacle.
DO NOT run the cord over carpeting or other heat insulators. DO NOT cover the cord. Keep cord away from trafﬁc areas, and DO NOT submerge in water.
We do not recommend the use of an extension cord, as it may overheat and become a ﬁre hazard. If you must use an extension cord, use No. 14 AWG minimum size and rated no less than 1875 watts.
Unplug the ice maker before cleaning or making repairs.
Exercise caution and use reasonable supervision when the appliance is used near children.
DO NOT clean your ice maker with ﬂammable ﬂuids. The fumes can create a ﬁre hazard or explosion.
DO NOT tip over.
If the ice maker is brought indoors from outdoors during the wintertime, give it a few hours to adjust to room temperature before plugging it in.
DANGER: Risk of ﬁre or explosion. The flammable refrigerant used. DO NOT use mechanical devices to defrost the ice maker.
DO NOT puncture refrigerant tubing.
DANGER: Risk of ﬁre or explosion. The flammable refrigerant used. To be repaired only by trained service personnel. DO NOT puncture refrigerant tubing.
CAUTION: Risk of ﬁre or explosion. The flammable refrigerant used. Consult repair/owner’s manual before attempting to install or service this product. All safety precautions must be followed.
CAUTION: Risk of ﬁre or explosion. Dispose of properly in accordance with local or federal regulations. The flammable refrigerant used.
CAUTION: Risk of ﬁre or explosion due to puncturing of refrigerant tubing. Follow handling instructions carefully. The flammable refrigerant used.
The ice maker should be installed in accordance with the safety standard for refrigeration systems, ASHRAE15. The ice maker shall not be installed in corridors or hallways of public buildings.
If the unit has a problem that needs service or parts replaced, the service must be done by factory authorized personnel to minimize the risk of the refrigerant igniting due to incorrect parts or improper service.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY SAVE THESE INSTRUCTIONS

SPECIFICATIONS

Dimensions (W x H x D)	9.5” x 12.9” x 14.1” (242 mm x 328 mm x 358 mm)
Weight	17.0 lbs (7.7 kg)
Ice Producing Capacity	Up to 26 Lbs a day

PARTS AND FEATURES

a. See-Through Window (Allows visibility of the interior)
b. Ice Full Sensor
c. Ice Basket
d. Ice Scoop
e. Control Panel
f. Air Outlet
g. Water Drain Cap (At the front underside of the unit)
h. Maximum Water Level (Not shown on the unit image above. You can see the water level mark when the ice basket is removed.)

INSTALLATION INSTRUCTIONS

UNPACKING YOUR ICE MAKER

Remove all exterior and interior packaging. Check that the ice basket and ice scoop are included. If any parts or accessories are missing, please contact customer service.
Clean the interior with lukewarm water and a soft cloth. Remove the ice basket and wash it in warm water.
Find a location for your ice maker that is protected from direct sunlight and other sources of heat (i.e.: stove, furnace, radiator). Place the ice maker on a level surface. Make sure that there is at least 5 inches of space between the back and sides of your ice maker and the wall.
Allow one hour for the refrigerant fluid to settle before plugging it into the unit.
The appliance must be positioned so that the plug is accessible.

CONNECTING YOUR ICE MAKER

DANGER: Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged.

This unit should be properly grounded for your safety. The power cord if this appliance is equipped with a three-prong plug that connects with standard three-prong wall outlets to minimize the possibility of electric shock.
Plug your appliance into an exclusive, properly installed, grounded wall outlet. DO NOT under any circumstances, cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician.
This appliance requires a standard 115 Volt, 60 Hz electrical outlet with three-prong ground.
NOTE: Before using your ice maker, it is strongly recommended to clean it thoroughly.
WARNING: The ice maker is not designed to be installed in an outside area such as a garage or a porch.
Ambient temperatures of below 50°F or above 100.4°F will hinder the performance of the appliance.

OPERATING INSTRUCTIONS

CONTROL PANELa. Button to turn on/off the unit
b. Button to select ice cube size
c. Power Indicator.
d. Ice Full Indicator
e. Water Shortage Indicator
f. Selected ice size: Small or large

BEFORE USE

Before connecting the appliance to the power supply, let the unit stand upright for 1 hour, which will reduce the possibility of the cooling system malfunctioning due to improper handling.
Clean your unit thoroughly before putting into use. (Refer to “CARE AND MAINTENANCE”.)
Use the parts diagram on page 6 to insure proper positioning of internal components.

USING YOUR ICE MAKER

Clean your ice maker thoroughly.
Open the cover, remove the ice basket and pour normal tap water into the tank. Keep water level below the level mark.
Plugin the unit and the power indicator light will blink.
Press “POWER” on the control panel to begin the ice-making cycle. The power indicator light will light.
Select the size of the ice cube by pressing the “SELECT” button. If the ambient temperature is below 60°F, it is recommended to select a small size to avoid ice sticking together.
While the ice maker is on, check the water level periodically. If the water pump cannot inject water, the ice maker will stop automatically, and the “WATER” indicator will be on. Press the “POWER” button, ﬁll water up to the level mark, and press “POWER” again. Allow 3 minutes for the refrigerant to settle before restarting.
The icemaker automatically stops working when the ice basket is full and the “ICE FULL” indicator will be illuminated.

WARNING: Direct or reﬂected sunlight may cause the infrared sensor to malfunction. If the unit doesn’t stop making ice, even when full, move the unit where there is no sunlight. Change water in the water reservoir every 24 hours to ensure a reasonable hygiene level. If the unit is not in use, drain all water in the tank reservoir.

CARE AND MAINTENANCE

HOW TO CLEAN

Remove the ice basket.
Remove the drain plug from the front underside to drain the water.
Clean the interior with diluted detergent, warm water, and a soft cloth.
The outside of the ice maker should be cleaned regularly with a mild detergent solution and warm water.
Dry the interior and exterior with a soft cloth.
Put back the drain plug.
When the machine is not in use, open a water drain cap to drain the water completely from the water reservoir.

CARE AND MAINTENANCE

The ice maker should be cleaned on a regular basis.
It is necessary to have an adequate ventilation space around the ice maker in order to sustain proper performance, dissipation of heat, maintain efficiency, and low power consumption. Clearance of a minimum of 5 inches should be maintained at the rear and sides of the unit and 8 inches at the top of the unit
To attain proper performance, be sure to plug the appliance into a properly grounded 115/60 Hz outlet.
DO NOT modify the power cord under any circumstances to allow the unit to be plugged into a non-grounded outlet. To avoid heat damage to the power cord, please ensure that it does not come in proximity or in direct contact with the compressor of the ice maker.
Please avoid installing the ice maker in a location where the appliance will come in contact with water or moisture to minimize rusting of metal parts.
The ice maker should not be installed near any heat source or in a location where it will come in direct contact with the sunlight.

TROUBLESHOOTING

Problem	Possible Cause	Solution
The “ADD WATER” indicator is on.	Lack of water.	Stop the ice maker, gill water, and press the “POWER” button again to restart the unit
“ICE” indicator is on.	The ice basket is full.	Remove ice from the ice basket or continuously press the “SELECT” button for 5 seconds. The unit could make ice 10 cycles even “ICE” indicator is on.
“WATER” and “ICE” indicators are both illuminated.	Ice shovel is stuck.	Check if ice is blocking the ice shovel, otherwise consult a certified technician.
Ice cubes stick together.	Ice making cycle is too long.	Stop the ice maker, and restart when the ice blocks melt. Select the small ice size.
	The water temperature in inner tank is too low.	Change the water in the reservoir. Use water between 45°F-90°F.
	Leaving ice in the appliance for an extended period of time may result in the appliance recycling the ice by melting it down and making a new batch.	Transfer ready-made ice to another container and store in a cooler or freezer to avoid recycling.
Ice cubes are melting.	Leaving ice in the appliance for an extended period of time may result in the appliance recycling the ice by melting it down and making a new batch.	After extended period transfer ready-made ice to another container and store in a cooler of the freezer to avoid recycling.
Ice making cycle is normal but no ice is made.	Ambient temperature or water temperature in inner tank is too high.	Operate the ice maker below ambient temperature of 90°F and use cold water.
	Refrigerant liquid leakage.	Consult a qualified technician.
	Pipe in the cooling system is blocked.	Consult a qualified technician.