ENGLISH
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with your new OttLite® product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and return it today by mail.
WARNING: To prevent electric shock, make sure the lamp is not plugged in until all steps are complete.
NOTE: THIS UNIT IS FULLY ASSEMBLED
- Remove lamp from packing, placing lamp body base (A) flat on a steady surface.
- Connect power adapter input (H) into connector (J) in the rear-bottom of the lamp.
- Plug the power adapter (G) into a standard household 120V AC outlet. Note:
Only use with the supplied power adapter to avoid damage or fire. - Turn the lamp ON/OFF by using power switch in touch panel (B) located on top of
base (A). Power switch (B) is a “touch” switch that controls the dimmer function
from low to high brightness setting. A quick touch will turn the lamp on and off. - Wireless charger for Qi-certified devices (C) is located in the center of base (A).
See Wireless Charging Instructions section for details. - To power LED dimmer setting, slightly touch switch (B) to turn “ON” lamp and
achieve the following:
• To operate dimmer function; continuously “press” switch to increase
brightness. Stop pressing switch once desired brightness level is achieved.
• Continuously “press” switch again to decrease brightness. Stop pressing
switch once desired brightness level is achieved. - To reposition the light, hold the lamp base (A) steady and grasp either lamp
body (D) or shade (E) depending on needed adjustment.
WIRELESS CHARGING INSTRUCTIONS:
Wireless charging requires a Qi-certified device. To determine if your device is Qi-certified, please visit the Wireless Power Consortium website. To wirelessly charge a device, perform the following:
- Check for a RED light on top of base (A). This signifies a device can be charged.
- Place the device, which supports Qi wireless charging standard, face up on the middle
of the Qi wireless charging icon (C). - A different light on top of base (A) will turn BLUE noting charging mode is active.
- When the device is centered on the Qi wireless charging icon (C), a solid BLUE
light will indicate the device is charging properly. NOTE: If a solid RED light, or a
RED or BLUE blinking light is visible, this indicates the device is not charging and
needs to be properly centered. - Check the charge level on your device periodically to determine when device is fully
charged. NOTE: Lamp DOES NOT provide any indication of when device is fully charged.
CAUTION! DEVICE MAY BECOME WARM DURING CHARGING. THIS IS NORMAL
AND PART OF THE PROCESS. CHARGING TIMES VARY BY DEVICE.
SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
- Turn lamp off and WAIT UNTIL LAMP HEAD (E) IS COOL before handling.
- The LED panel (F) might get hot after several hours of continuous use DO NOT place
your hands directly on LED light panel. - Never use with an extension cord unless the plug can be fully inserted into the
receptacles in the extension cord. - Do not alter the plug.
- The lamp head included with this unit cannot be replaced by the consumer.
- INDOOR USE ONLY.
NOTE: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.
Power Up LED Desk Lamp with Wireless Charging
CAUTION! If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer orits service agent ora similar qualified person in order to avoid a hazard. Indoor use only.
CAUTION! THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN
THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.
FCC Part 15
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that of the receiver.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CAN ICES-001 (B)/NMB-001 (B)
CAN ICES-005 (B)/NMB-005 (B)
CAUTION: Any change or modification to product not expressly recognized by OttLite Technologies voids OttLite’s responsibility for proper function of product.
POWER ADAPTER SPECIFICATION:
Input: AC 100-240V, 50/60 Hz, 1.2A Max
Output: 12V DC, 2A with a Male DC Plug
Qi CHARGER SPECIFICATION:
Output: 5V, 1A or 5 watts
THIS LAMP CONTAINS a 5V, 2,1A USB output port (K) located on the bottom rear of lamp. USB port can charge items such as tablets, cellular phones, etc. The “Qi” symbol is a trademark of the Wireless Power Consortium