Perlesmith PSMTK1 Medium Tilt TV Wall Mount

PSMTK1

WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER INSTALLATION OR ASS EMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.
If you do not understand the instructions or have any concerns or questions, please contact a qualified installer.
Do not install or assemble if the product or hardware is damaged or missing. Not all parts and hardware included must be used. If you require replacement parts, contact customer service at: [email protected]
This product has been designed for using on vertical wall constructed of wood studs. Wood studs being defined as a wall consisting of a minimum of 2x 4studs with a maximum of 16stud spacing with a maximum of 1/2of wall covering (drywall, lath, plaster).For custom installations please contact a qualified installer.
This product may contain moving parts. Use with caution.
Please check www.perlesmith.com for more products and company information.

Tools Needed

Hardware Included

WARNING: This product includes small items that could cause a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, please contact: [email protected] and you will get the new parts ASAP
NOTE: Not all parts and hardware included will be used

Hardware (Wall/product)

CAUTION: These concrete anchors are for concrete and brick installations ONLY. Do not use in drywall or wood.

TV Screws / Washers

STEP 1-1 Select TV Screw Diameter

Thread screws by hand into the threaded holes on the back of your TV to select which screw diameter fit your TV

STEP 1-2 Select TV Screw Length

When attaching brackets to the flat screen, be careful not to over tighten screws and be sure that screws do not bottom out in the mounting holes.

STEP 1-3 Attach the TV Bracket

Position your TV bracket configuration (A or B) over your TV hole pattern – making sure the bracket is centered over the TV hole pattern and level. Secure bracket using your screw/washer (A-Flat Back) or spacer/screw/ washer (B-Round Back/ Extra Space) selection.
CAUTION: Ensure TV bracket is securely fastened before moving on to
the next step.

(a) Flat Back

(b) Round Back/ Extra Space

STEP 2A Wall Plate Installation (Concrete or brick)

CAUTION: Avoid potential personal injury or property damage! All lag bolts firmly tightened to prevent unwanted movement of the wall plate .
CAUTION: Ensure the wall plate is securely fastened to the wall before continuing to the next step.

2A-1

Position the wall plate  at your desired height, level the wall plate and mark the pilot hole locations.

2A-2

2A-3

Install wall plate using lag bolts  and washer  and anchor .
Tighten the lag bolts until they are pulled firmly against the wall plate .

STEP 2B Wall Plate Install (Wood stud)

CAUTION: Avoid potential personal injuries and property damage!

• Drywall covering the wall must not exceed 5/8 in. (16mm)
• Minimum wood stud size: common 2 x 4 in.(51×102 mm) nominal 1½ x 3½ in.(38 x 89mm)

CAUTION: Avoid potential personal injury or property damage! All lag bolts firmly tightened to prevent unwanted movement of the wall plate .
CAUTION: Ensure the wall plate is securely fastened to the wall before continuing to the next step.

2B-1

Position the stud. Verify and mark the center of the stud by finding the stud edges using an awl, a thin nail, or an edge to-edge stud finder.

2B-2

Position the wall plate at your desired height and line up the holes with your stud center line.
level the wall plate and mark the holes.

2B-3

Drill pilot holes using a 7/32 in.
(5.5mm) diameter drill bit.

IMPORTANT: Pilot holes must be drilled to a depth of 2¾ in.(70mm). Be sure to drill into the center of the stud.

2B-4

Install the wall plate assembly using lag bolts and washer Tighten the lag bolts only until it against the wall plate

STEP 3 Tighten Nuts

Please adjust the tilting angle with the Allen wrench for both and as
the pictures show before hanging TV

STEP 4 Hang TV

STEP 5 Secure TV

Pull the strap down and push the TV to secure the TV brackets and to the wall plate .If cannot tilt TV, please take TV off and then adjust the tilt as STEP 3 shows.

Installation Instruction

V1.0
PSFS01

https://www.perlesmith.com
Thank you for choosing our product! We strive to provide the best quality and services for our customers. Would you kindly share your experience on Amazon if you are satisfied? Should you have any issues, please don’t hesitate to contact us. Telephone800-5566-806 Mon-Fri 10am – 6pm (PST) (USA) (CAN) [email protected] (US/CA/DE/UK/FR/IT/ES/JP/AU)

IMPORTANT SAFETY INFORMATION

WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER INSTALLATION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.

• If you do not understand the instructions or have any concerns or questions, please contact customer service at [email protected]
• Do not install or assemble if the product or hardware is damaged or missing.
• Not all parts and hardware included will be used. lf you require replacement parts, contact customer service at [email protected]
• This product may contain moving parts. Use with caution. ·Please check www.perlesmith.com for more products and company information.

Supplied Parts List

Step 1 Connecting the Support Pillar to Tempered Glass

Step 2 Connecting the TV Plate to Support Pillar

Step 3 Measure VESA and Check TV screws

Step 3 Measure VESA and Check TV screws

Measure the distance between the holes located at the back of your TV (these measures may form the shape of a square, or a rectan-gle) and check that these taken measures are within the VESA(*) range for this wall mount. (*) VESA: International standard established by the TV manufacturers used to determine if LCD/LED TVs are compatible with wall mounts.

Check TV screws

Hand thread screws into the threaded inserts on the back of your TV to determine which screw diameter (M6, or M8) to use.

When attaching brackets to the flat screen, be careful not to over tighten screws and be sure that screws do not bottom out in the mounting holes.

Step 4 Mounting the Monitor Bracket to a TV

FLATBACK TV (UNIVERSAL MONITOR PLATE)
ROUND BACK TV (UNIVERSAL MONITOR PLATE)
First, make sure the diameter of the bolt(TV1-6) fits your TV. Then, please see the diagram above. You will need to thread the bolt into the TV using the correct washer (TV9) and spacer (TV7 or TV8) if necessary with a screwdriver(Not included). Please make sure the monitor brackets(4) are vertically centered and level with each other.

Step 5 Attaching TV to TV Plate and Managing the Wires

Step 6 Adjusting the Height of the TV

Height adjustable vertical bracket(4) first choice
If you find your TV set is too close to the base, please take off the TV from the stand. Then, change to the second choice or third choice to allow more space between TV and the tempered glass base (3).