Soundbar Fidelio B95
View Fullscreen
Soundbar 5.1.2 Fidelio B95
TAPR802
User manual
Register your product and get support at
www.philips.com/support
Contents
1 Important Safety Care for your product Care of the environment Compliance Help and support
2 Your product What’s in the box Main unit Remote control Wireless subwoofer Connectors
2
5 Settings
16
2
Adjust speaker level
16
3
Set display brightness
16
3
Auto standby
16
3
Apply factory settings
16
3
6 Update software
17
4
Update software via Wi-Fi
17
4
Update via USB
17
4
5 6 6
7 Wall mount your product Wall mount
18 18
3 Connect and set up
7
8 Product specifications
19
Placement
7
Connect to TV
7
9 Troubleshooting
20
Connect TV or digital devices
through HDMI
8
Connect audio from TV or
other devices
8
Connect to power
9
Pair up with the subwoofer
9
Connect to Wi-Fi
(Wireless Operation)
10
4 Use your product
12
Insert batteries before using
the remote control
12
Adjust the volume
12
Choose your sound
12
Dolby Atmos®
13
Play audio through Bluetooth 14
MP3 player
14
Play-Fi multi-room
15
Chromecast(audio) / AirPlay2
/ Alexa 3PDA
15
Listen to Spotify
15
1 EN
1 Important
Read and understand all instructions before you use your product. If damage is caused by failure to follow instructions, the warranty does not apply.
Safety
Risk of electric shock or fire! · Before you make or change any
connections, make sure that all devices are disconnected from the power outlet. · Never expose the product and accessories to rain or water. Never place liquid containers, such as vases, near the product. If liquids are spilt on or into the product, disconnect it from the power outlet immediately. Contact Consumer Care to have the product checked before use. · Never place the product and accessories near naked flames or other heat sources, including direct sunlight. · Never insert objects into the ventilation slots or other openings on the product. · Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. · Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. · Disconnect the product from the power outlet before lightning storms. · When you disconnect the power cord, always pull the plug, never the cable. · Use the product in tropical and/or moderate climates.
Risk of short circuit or fire! · For identification and supply ratings, see
the type plate at the back or bottom of the product. · Before you connect the product to the power outlet, ensure that the power voltage matches the value printed on the back or bottom of the product. Never connect the
2 EN
product to the power outlet if the voltage is different.
Risk of injury or damage to this product! · For wall mounting, this product must be
securely attached to the wall in accordance with the installation instructions. Use only the supplied wall mount bracket (if available). Improper wall mounting may result in accident, injury or damage. If you have any query, contact Consumer Care in your country. · Never place the product or any objects on power cords or on other electrical equipment. · If the product is transported in temperatures below 5°C, unpack the product and wait until its temperature matches room temperature before connecting it to the power outlet. · Parts of this product can be made of glass. Handle with care to avoid injury and damage.
Risk of overheating! · Never install this product in a confined
space. Always leave a space of at least four inches around the product for ventilation. Ensure curtains or other objects never cover the ventilation slots on the product.
Risk of contamination! · Do not mix batteries (old and new or
carbon and alkaine, etc.). · Danger of explosion if batteries are
incorrectly replaced. Replace only with the same or equivalent type. · Remove batteries if they are exhausted or if the remote control is not to be used for a long time. · Batteries contain chemical substances, they should be disposed of properly.
Risk of swallowing batteries! · The product/remote control may contain
an AAA battery, which can be swallowed. Keep the battery out of reach of children at all times! If swallowed, the battery can cause serious injury or death. Severe internal burns can occur within two hours of ingestion. · If you suspect that a battery has been swallowed or placed inside any part of the body, seek immediate medical attention. · When you change the batteries, always keep all new and used batteries out of
reach of children. Ensure that the battery compartment is completely secure after you replace the battery. · If the battery compartment cannot be completely secured, discontinue use of the product. Keep out of reach of children and contact the manufacturer.
This is CLASS II apparatus with double insulation, and no protective earth provided.
~
AC voltage
Use only the power supplies listed in the user manual.
Care for your product
Use only microfiber cloth to clean the product.
Care of the environment
Disposal of your old product and battery
Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.
This symbol on a product means that the product is covered by European Directive 2012/19/EU.
3 EN
This symbol means that the product contains batteries covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. Inform yourself about the local separate collection system for electrical and electronic products and batteries. Follow local rules and never dispose of the product and batteries with normal household waste. Correct disposal of old products and batteries helps prevent negative consequences for the environment and human health.
Removing the disposable batteries To remove the disposable batteries, see battery installation section.
Compliance
This product complies with the radio interference requirements of the European Community. Hereby, TP Vision Europe B.V. declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.p4c.philips. com.
Help and support
For extensive online support, visit www.philips.com/support to:
· download the user manual and the quick start guide
· watch video tutorials (available only for selected models)
· find answers to frequently answered questions (FAQs)
· email us a question · chat with our support representative.
Follow the instructions on the website to select your language, and then enter your product model number. Alternatively, you can contact Consumer Care in your country. Before you contact, note down the model number and serial number of your product. You can find this information on the back or bottom of your product.
2 Your product
Congratulations on your purchase, and
Main unit
This section includes an overview of the main unit.
of product software upgrade), register your product at www.philips.com/support .
What’s in the box
Check and identify the items in the package: · Soundbar x1 · Wireless subwoofer x1 · Remote control x1 · AAA battery x2 · Power cord* x2 · Power adapter x1 · Wall mount kit (wall bracket x2, screw x 6,
dowel x2) · Quick start guide · Warranty card · Safety sheet · Mounting guide *Power cord quantity and plug type vary by regions.
1 234 5
6
æ +/- (Volume) · Increase or decrease volume.
ç (Play/Pause) · Play, pause or resume in Bluetooth playback.
è (Source) · Press to select an input source for this product.
é (Standby-On) · standby) · standby)
ê Display panel
ë Power and Wi-Fi LED indicator
LED indicator Color
White
Display Power state Wi-Fi network Sources available to use Panel
Eco standby Disconnected All sources are shut down.
Amber
Semi-
Connected Play-Fi, Chromecast(Audio), AirPlay2,
standby
Alexa 3PDA & Spotify Connect
(These sources are running in
background.)
Amber
On
Power on Connecting HDM1, HDMI2, E-ARC(ARC), OPTICAL &
BT
Amber
On
Power on Connected All sources are ready.
4 EN
Remote control
This section includes an overview of the remote control.
1
2
9
3
4
8
5
7
6
a (Standby-On) · Short press: Switch On / Off (Semistandby) · Long press(5 sec): Switch Off (Eco standby)
b (Source) Select an input source for this product. · HDMI 1: Switch your source to the HDMI IN 1 connection. · HDMI 2: Switch your source to the HDMI IN 2 connection. · E-ARC: Switch your source to HDMI E-ARC or ARC connection. · OPTICAL: Switch your audio source to the optical connection. · AUDIO IN: Switch your audio source to AUDIO IN connection (3.5mm jack). · BT: Switch to Bluetooth mode.
Note
Play-Fi multi-room, Chromecast(Audio), AirPlay2, Alexa 3PDA & Spotify Connect are running in background when Wi-Fi is connected. They are selected and controlled by respective casting device/APP.
c Navigation buttons · Up: Increase volume or select the previous item in the menu. · Down: Decrease volume or select the next item in the menu. · Left: Skip to the previous track in playback mode or select level down in the menu mode. · Right: Skip to the next track in playback mode or select level up in the menu mode. · Center: Play, pause or resume in playback mode. Confirm a selection.
d (Menu) Enter the general settings menu.
SUB CTR
SIDE L
SIDE R
DIM DISP BT PAIR
UPGRADE
Subwoofer gain control Center speakers relative volume level Left side firing speaker relative volume level Right side firing speaker relative volume level Display brightness level Display auto off Start BT pairing (BT source only) Firmware upgrade via USB
e (Equalizer)
Select surround sound modes: (Movie/
Music/Voice/Sport/Custom).
MOVIE MUSIC VOICE
Preset EQ for movie Preset EQ for music Prest EQ for news or talk
show SPORT Preset EQ for sport
programme CUSTOM User custom EQ (controlled
in Philips Sound app)
5 EN
f Select a height effect level for Dolby Atmos.
g (Sound) Select sound settings: (Surround/DRC/ IMAX/Dialogue/Bass/Treble/Sync).
SUR DRC IMAX DLG CTRL
BASS
TREBLE
SYNC
Surround sound options Dynamic Range control IMAX mode options Adjust dialogue level (for DTS-X only) Adjust bass level for preset EQ Adjust treble level for preset EQ Adjust audio and video sync delay (HDMI only)
h Exit settings.
i Mute or restore volume.
Wireless subwoofer
This product comes with a wireless subwoofer.
CONNECT
1
2
AC MAINS~
3
a CONNECT (Connect) Press and hold for 5 seconds to enter the pairing mode between the main unit and the subwoofer.
b Subwoofer indicator · When the power is turned on, the indicator lights up. · During wireless pairing between the subwoofer and the main unit, the indicator blinks white quickly.
6 EN
· When the pairing succeeds, the indicator lights up white.
· When the pairing fails, the indicator blinks white slowly.
· When the wireless connection is disconnected for 1 minute, the indicator turns off.
c AC MAINS Connect to the power supply.
Connectors
This section includes an overview of the connectors available on the main unit.
1
5
2
3 6
4
a DC IN Connect to the power adapter.
b AUDIO IN Connect to an audio output (3.5mm jack) on a device.
c OPTICAL IN Connect to an optical audio output on the TV or a digital device.
d USB (For service) Connect to a USB flash drive to upgrade software of this product.
e HDMI OUT (eARC/ARC) Connect to the HDMI (eARC/ARC) input on the TV.
f HDMI IN 1 / HDMI IN 2 Connect to the HDMI output on a digital device.
3 Connect and set up
This section helps you connect this product to a TV and other devices, and then set it up. For information about the basic connections of this product and accessories, see the quick start guide.
Caution · For identification and supply ratings, see the
type plate at the back or bottom of the product.
· Before you make or change any connections,
make sure that all devices are disconnected from the power outlet.
Placement
Place the subwoofer at least 1 meter (3 feet) away from the main unit, and 10 centimeters (4 inches) away from the wall.
For best results, place your subwoofer as shown below.
10cm/4″
1m/3ft
SUB WOOFER
Connect to TV
Connect this product to your TV. You can enjoy audio from TV programs through the soundbar speaker. Use the best quality connection available on your soundbar speaker and TV.
Connect to TV through HDMI (ARC/eARC)
This product supports HDMI with eARC (Enhance Audio Return Channel). eARC is a new function standardized by HDMI 2.1 and supports the latest audio formats in addition to audio formats that are supported with existing ARC (Audio Return Channel). If your TV is HDMI eARC compliant, you can enjoy the TV audio that ARC cannot transfer, such as Dolby Atmos-Dolby TrueHD and DTS:X, or multi-channel LPCM contents, by using a single HDMI cable.
What you need · A High-Speed HDMI cable. · Your TV supports both HDMI ARC and
HDMI-CEC (see the TV user manual for details). · For some TV models, enable the external speaker output from the TV setting menu (see the TV user manual for details).
(eARC/ARC) HMDI IN (eARC/ARC) TV
1 Using a High Speed HDMI cable, connect the HDMI OUT connector on this product to the HDMI ARC connector on your TV. · The HDMI ARC connector on the TV might be labeled differently. For details, see the TV user manual.
7 EN
2 On your TV, turn on the HDMI-CEC operations. For details, see the TV use manual.
3 Repeatedly press the source button until E-ARC displays on the display panel.
Note
· Your TV must support the HDMI-CEC and ARC
function and you must enable them.
· 100% interoperability with all HDMI-CEC
devices is not guaranteed.
· Only HDMI 2.1 compatible cables can support
the eARC function.
· If your TV is not HDMI ARC compliant, connect
an audio cable then enjoy the TV audio through this product.
Connect TV or digital devices through HDMI
If your TV is not HDMI ARC-compliant, connect your soundbar to the TV through a standard HDMI connection. You can also connect a digital device such as a set-top box, DVD/Blu-ray player, or games console to this product through a single HDMI connection. When you connect the devices in this way and play a file or game, the · video is automatically displayed on your
TV, and · audio is automatically played on this
product.
1 Using a High-Speed HDMI cable, connect the HDMI OUT connector on your digital device to the HDMI IN 1/2 on this product.
2 Connect this product to TV through HDMI OUT. If the TV is not HDMI CEC compliant, select the correct video input on your TV.
3 On the connected device, turn on HDMI-CEC operations. For details, see the user manual of the device.
HDMI OUT (eARC/ARC)
HDMI 1 / HDM2I
Blu-ray Player / DVD Player / Recorder / Set-top Box…
HDMI OUT
TV TV
HDMI IN
Connect audio from TV or other devices
Play audio from TV or other devices through this product. Use the best quality connection available on your TV, soundbar, and other devices.
Note · When this product and TV are connected
through HDMI ARC, an audio connection is not required.
Option 1: Connect audio through a digital optical cable
TV
1 Using an optical cable, connect the OPTICAL IN connector on this product to the OPTICAL OUT connector on the TV or other devices.
· The digital optical connector might be labeled OPTICAL OUT, SPDIF or SPDIF OUT.
2 Repeatedly press the source button until OPTICAL displays on the display panel.
8 EN
Option 2: Connect audio through an analog audio cable
AUDIO OUT LR
1 Using an analog cable, connect the AUDIO IN connector on this product to the AUDIO OUT connector or analog audio output connectors (red and white) on TV or other devices.
2 Repeatedly press the source button until AUDIO IN displays on the display panel.
Connect to power
· Before connecting to the AC power cord, make sure that you have completed all other connections.
· Risk of product damage! Make sure that the power supply voltage corresponds to the voltage printed on the back or the underside of the main unit.
· Connect the mains cable to the DC socket of the main unit and then into a mains socket.
· Connect the mains cable to the AC~ socket of the subwoofer and then into a mains socket.
Pair up with the subwoofer
Automatic pairing
The wireless subwoofer automatically pairs up with the main unit for wireless connection when you turn on the main unit and the subwoofer.
9 EN
Determine the status based on the wireless subwoofer indicator.
LED behavior Fast blink Constant on
Slow blink
Status Subwoofer in pairing mode Connected / Pairing successfuly Connecting / Pairing failed
Note
· Do not press the CONNECT (Connect) button
on the rear of the subwoofer, except for manual pairing.
Manual pairing
If no audio from the subwoofer can be heard, manually pair up the subwoofer. 1 Unplug both the main unit and the
subwoofer from the mains sockets, then plug them in again after 3 minutes.
2 Press and hold the CONNECT (Connect) button on the rear of the subwoofer for 5 seconds.
» The indicator on the subwoofer blinks quickly.
3 Press and hold on the main unit or remote control for 5 seconds to switch the main unit to Eco standby.
4 Press on the main unit or remote control to switch the main unit on.
» The indicator on the subwoofer blinks white quickly and SBW PAIRING displays on the display panel.
» If the pairing succeeds, the indicator on the subwoofer lights up white and SBW PAIRED displays on the display panel.
5 If the pairing fails, the indicator on the subwoofer blinks slowly and CHK SBW displays on the display panel. Repeat the steps above.
Note
· The subwoofer should be within 6 meters from
the main unit in an open area (the closer the better).
· Remove any obstacles between the subwoofer
and the main unit.
· If the wireless connection fails again, check if
there is a conflict or strong interference (e.g. interference from an electronic device) around the location. Remove them and try again.
· If the wireless dis-connection or pairing lasts for 1
minute, the subwoofer automatically switches to standby and the LED on the subwoofer turns off.
» If the connection succeeds, PLAY-FI displays on the display panel.
Note
For iOS version only Wi-Fi network used by iPhone should be switched temporarily to Play-Fi device AP and restart Philips Sound app to complete the product’s Wi-Fi setup. See the steps below:
· Go to Settings. · Select Wi-Fi setting.
Connect to Wi-Fi (Wireless Operation)
(For iOS and Android version)
By connecting this unit and mobile devices (such as iPad, iPhone, iPod touch, Android phones, etc.) to the same Wi-Fi network, you can then use the Philips Sound app powered by DTS Play-Fi to control the soundbar to listen to audio files.
1 Connect your phone or tablet to the same Wi-Fi network that you want to connect your soundbar.
2 Download and install the Philips Sound app powered by DTS Play-Fi on your device.
* Make sure your router is turned on and working properly.
3 Press and hold the (Wi-Fi) button located on the back cabinet for 8 seconds to trigger the Wi-Fi connection.
» Until the speaker makes a second tone and then release the button.
4 Wait until the Wi-Fi LED indciator on the front cabinet goes from a fast blink to a slow pulse. When it begins to slow pulsing indicating that the speaker is entering the Wi-Fi setup mode.
5 Launch the Philips Sound app powered by DTS Play-Fi. Follow the instructions in the app to connect this product to your Wi-Fi network.
10 EN
· Select the Play-Fi
device in the Wi-Fi setup.
· Return to Philips
Sound app to continue the setup.
6 After successful Wi-Fi connection, the Wi-Fi LED indicator on the front cabinet will stop pulsing and turn solid. Once you set up this product on your Wi-Fi network, you can control it from any smartphone or tablet on the same network.
» When using the app to play music, the display panel will show PLAY-FI.
7 After connection, you can change the device name. There are several names to choose from or create your own by choosing Custom Name at the bottom of the name list. Otherwise, if follows the default name.
8 After connection, this product may perform a software update.
» Upgrade to the latest software when it is set up for the first time. The software upgrade may take several minutes. Do not unplug your speaker, turn off your device, or break the network during the update.
AirPlay setup Use AirPlay to set up the Wi-Fi connection between iOS device (iOS7 or later) and soundbar.
1 iOS device: Settings > Wi-Fi > select home network [Play-Fi device (xxxxxx)].
2 Launch the Philips Sound app powered by DTS Play-Fi. Follow the instructions in the app to connect this product to your Wi-Fi network.
» After successful Wi-Fi connection, the Wi-Fi LED indicator on the front cabinet will stop pulsing and turn solid. Once you set up this product on your Wi-Fi network, you can control it from any smartphone or tablet on the same network.
» When using the app to play music, the display panel will show PLAY-FI.
3 After connection, you can change the device name. There are several names to choose from or create your own by choosing Custom Name at the bottom of the name list. Otherwise, if follows the default name.
4 After connection, this product may perform a software update.
» Upgrade to the latest software when it is set up for the first time. The software upgrade may take several minutes. Do not unplug your speaker, turn off your device, or break the network during the update.
Note
· After connection, the product may perform a
software update. Upgrade is required after initial setup. Without the upgrade, not all product features can be available.
· When the first-time setup is not successful,
press and hold the Wi-Fi button on the soundbar for 8 seconds until the second tone can be heard and the Wi-Fi LED is changed to slow pulse. Reset the Wi-Fi connection, restart the app and start the setup again.
· If you want to change from one network to
another, you need to set up the connection again. Press and hold the Wi-Fi button the soundbar for 8 seconds to reset the Wi-Fi connection..
WPS mode If your router has Wi-Fi Protected Setup (WPS), you can set up the connection without entering a password.
1 Press and hold the Wi-Fi button for 4 seconds. You will hear a tone and the Wi-Fi LED will begin in double blink.
2 Press the WPS button on your
WPS
router. The button is normally marked with this WPS logo.
3 Follow the instruction in Philips Sound app powered by DTS Play-Fi to start the pairing.
Note
· WPS is not a standard feature on all routers. If
your router does not have WPS then use the starndard Wi-Fi setup.
· Press the Wi-Fi button once if you want to exit
the WPS mode or it will automatically exit after 2 mintues..
11 EN
4 Use your product
This section helps you use this product to play media contents from all sources. Before you start · Make the necessary connections
described in the quick start guide and the user manual. · Switch this product to the correct source for other devices.
Insert batteries before using the remote control
Slide to remove the battery compartment cover, insert 2 AAA batteries (1.5V) with correct polarity, then slide the battery compartment cover back into position.
1 2
3
Adjust the volume
Press +/- (Volume) to increase or decrease a volume level. · To mute sound, press . · To restore the sound, press again or
press +/- (Volume).
Choose your sound
This section helps you choose the ideal sound for your video or music.
Preset EQ modes
Select predefined sound modes to suit your video or music.
Press on the remote control to select a preset EQ mode. · MOVIE: Create a surround listening
experience. Ideal for watching movies. · MUSIC: Create two-channel or multi-
channel stereo sound. Ideal for listening to music. · VOICE: Create sound effect which makes human voice more clear and outstanding for listening. · SPORT: Create an atmosphere as if watching a sports game in a stadium. · CUSTOM: Customize the sound based on your preferences (controlled in Philips Sound app: Settings > Fine Tune).
Bass/Treble levels adjustment
Change the low frequency (bass) and high frequency (treble) settings of this product.
Repeatedly press to select BASS or TREBLE, then press the left and right navigation buttons to change the bass or treble level.
The changes are effective in MOVIE, MUSIC, VOICE and SPORT EQ modes.
IMAX Enhanced mode
Repeatedly press to select IMAX, then press the left and right navigation buttons to set IMAX mode on or off.
Mode Auto
On
Off
Function IMAX Enhanced mode is detected and engaged automatcially. IMAX Enhanced mode is engaged even for DTS 5.1 bitstreams. Disable IMAX Enhanced mode for all bitstreams.
12 EN
Surround mode (SURR)
Repeatedly press to select SURR, then press the left and right navigation buttons to select surround mode options. · UPMX: Up-mixing mode for driving output
to all speakers even when content with audio channels lesser than the 5.1.2 (B95) or 7.1.2 (B97) speaker configuration. Upmixing technology from Dolby or DTS is applied according to content type. · STD: Standard mode for delivering original sound. The speaker outputs will follow the audio channels in content. (Note: If the audio content is 2.0 channel, only the left & right channel speakers and the subwoofer will output sound. Use UPMIX if virtual surround is desired.) · A-I: The media intelligence function of Dolby Atmos for home audio is utilized to drive the vocal enhancement or surround effects.
Dynamic Range Control (DRC)
You can apply dynamic range control to Dolby or DTS bitstreams.
Repeatedly press to select DRC, then press the left and right navigation buttons to turn DRC on, off or auto.
Note
· DRC is not available in BT/AUDIO IN/Play-Fi
mode.
Dialogue Control (DLG CTRL)
Dialogue mode improves the clarity of dialogue and vocals in movies, TV programs and podcasts by adjusting the tonal balance of this product.
Repeatedly press to select DLG CTRL, then press the left and right navigation buttons to adjust dialogue level.
This control is supported in DTS:X stream only.
13 EN
Synchronize video and sound (SYNC)
If the audio and video are not synchronized, delay the audio to match the video.
Repeatedly press to select SYNC, then press the left and right navigation buttons to synchronize the audio with the video.
Dolby Atmos®
In addition to horizontal distribution of 5-channel audio, this product also has built-in Dolby Atmos enabled speakers as additional audio channels to generate overhead distribution of audio for powerful delivery of 3D sound immersion and greater reality.
2.8~3m
0.7~0.8m 2~3m
Optimal setup for Dolby Atmos sound · Place this product at a height of
0.7m-0.8m. · Ceiling height is 2.8m-3m. · Listening distance from this product is 2m-
3m. · Ceiling is not made of sound absorbent
material. · Preferably no protrusive objects (such as
lighting and decorations) are on the ceiling.
Dolby Atmos® is available only in HDMI mode. For the details of the connection, please refer to “Connect to TV”. Best Dolby Atmos effects may be achieved through the following two use cases.
From your Blu-ray disc player: · Movie with Dolby Atmos. · Your Blu-ray disc player is connected to
this product via HDMI IN 1/2 connector. · On your Blu-ray disc player, enable
bitstream/raw audio format for HDMI sound output. · A high-speed HDMI cable.
From your TV: · Movie with Dolby Atmos. · Your TV supports Dolby Atmos bitstream/
raw output. · Your TV is connected to this product via
HDMI OUT connector. · A high-speed HDMI cable.
Note
· The full Dolby Atmos experience is only
available when the soundbar is connected to the source via a HDMI 2.0 cable.
· The soundbar will still work when connected via
other methods (such as a digital optical cable) but these are unable to support all the Dolby features. To ensure full Dolby support, you are strongly recommended to connect via HDMI.
Enjoy Dolby Atmos sound
Press
to select a height
surround effects level to best suit
your personal taste according to your
environment.
· ATMOS 00: minimal height effect. · ATMOS 01: small height effect. · ATMOS 02: medium height effect. · ATMOS 03: big height effect.
Note
· For non-HDMI connections (such as use of
Bluetooth, OPTICAL or AUDIO IN), only limited height surround effects are generated.
14 EN
Play audio through Bluetooth
Through Bluetooth, connect this product with your Bluetooth device (such as an iPhone, iPad, Android phone, or Android pad), and then you can enjoy the audio files stored on the device through the speakers of this product.
Note
· The maximum operational range between
this product and a Bluetooth device is approximately 10 meters (30 feet).
· The music streaming may be interrupted
by obstacles between the device and this product, such as wall, metallic casing that covers the device, or other devices nearby that operate in the same frequency.
· If you want to connect this product with
another Bluetooth device, break the current Bluetooth connection first.
1 Repeatedly press the source button to switch the main unit to Bluetooth mode, and wait until the display to show BT PAIR for starting the pairing operation.
2 On the Bluetooth device, turn on Bluetooth, search for and select “PlayFi Device (XXXXXX)-BT” to start connection.
» When the Bluetooth connection succeeds, BT CONNECTED displays on the display panel.
» If the connection fails, BT PAIR displays on the display panel.
3 Select and play audio files or music on your Bluetooth device.
4 To exit Bluetooth, select another source.
MP3 player
Connect your MP3 player to play your audio files or music.
What you need · An MP3 player. · A 3.5mm stereo audio cable.
1 Using the 3.5mm stereo audio cable, connect the MP3 player to the AUDIO IN connector on this product.
2 Repeatedly press the source button until AUDIO IN displays on the display panel.
3 Press the buttons on your MP3 player to select and play audio files or music.
Play-Fi multi-room
With Play-Fi built-in, your soundbar can sync or group with multiple Play-Fi enabled speakers for multi-room music which allows you to listen to the same song in every room of your house or different songs in different defined zones. All these are controlled by Philips Sound app. Source will be switched to Play-Fi as long as your soundbar is selected in the app.
To download Philips Sound app, please refer to “Wi-Fi (Wireless operation)” section. To learn more about Play-Fi operation, please visit play-fi.com.
Chromecast(audio) / AirPlay2 / Alexa 3PDA
Your soundbar is built-in with services running in background which support Chromecast(audio), AirPlay2 or Alexa 3PDA. When Wi-Fi is connected, you can cast audio from corresponding devices/apps at any time. Source will be switched automatically when respective streaming is detected.
Listen to Spotify
Use your phone, tablet or computer as a remote control for Spotify, go to spotify.com/ connect to learn how.
15 EN
5 Settings
Adjust speaker level
Repeatedly press to enter the settings menu, select the speakers below and press the left and right navigation buttons to adjust the speaker level
· SUB (subwoofer) · CTR XX (center speaker) · SIDE L XX (side left speaker) · SIDE R XX (side right speaker)
Apply factory settings
In case of no response from this product, you can reset this product to the default settings programmed at the factory.
In standby mode, press and hold VOL +/buttons on the main unit simultaneously for 8 seconds until RESET displays on the display panel.
When the factory settings restore is complete, the product automatically turns off and restarts.
Set display brightness
Repeatedly press to enter the settings menu, select DIM and press the left and right navigation buttons to adjust the brightness level of the display panel on this product. · HIGH (high) · MID (medium) · LOW (low)
Display auto off
Repeatedly press to enter the settings menu, select DISP and press the left and right navigation buttons to select DISP ON or DISP OFF.
Auto standby
When playing media from a connected device, this product automatically switches to standby if: · no source button is pressed for 15 minutes,
and · no audio/video playback is detected from
a connected device.
16 EN
6 Update software
To get the best features and support, update your product with the latest software.
Update software via Wi-Fi
Two parts in this product can be updated via Wi-Fi & Philips Sound App. 1 Play-Fi system 2 Audio system (Firmware) handles all
control and sound features
Play-Fi system This part can be updated directly by Philips Sound app. Once the product is connected with the app, It will check and prompt for update if a newer version software is available. Follow the steps on screen to complete the update. It is done over the air and the update time requires less than 10 minutes in normal network condition.
Audio system (Firmware) This part can be updated via the special tool (PS Fine Tune) provided in setting menu of Philips Sound App (settings>Fine Tune/ Update Firmware). When the update is available, the download icon will be shown (see the 2nd App screen capture below). Follow the steps provided on screen to complete the update.
B95
Caution
· During update, smartphone is required to turn
on and stay in the update screen until the whole process is finished.
· It may take 10-30minutes and please arrange
update to be done in product unused time.
Update via USB
Caution
· Do not turn off the power or remove the USB
flash drive when the software update is in progress because you might damage this product.
· The upgrade time may take around 8 minutes.
1 Check if there is the latest software version on www.philips.com/support.
» Search for your model and click on “Software and drivers”.
2 Download the software into a USB flash drive.
» Unzip the downloaded file and make sure that the unzipped folder is named “update.zip”.
» Put the “update.zip” folder in the root directory.
3 When turned on, plug the USB flash drive into the USB port of this product.
4 Press and hold and VOL+ buttons simultaneously for 3 seconds or select UPGRADE in setting menu.
» “FW UPG” (firmware upgrade) displays on the display panel.
5 Wait until the upgrade is completed. » If the upgrade is complete, this product automatically turns off and on again.
17 EN
7 Wall mount your product
Before you mount your product on the wall, read all safety precautions. (see `Safety’)
Wall mount
Note · Improper wall mounting may result in
accident, injury or damage. If you have any query, contact Consumer Care in your country.
· Secure the wall mount to a wall that can
support the combined weight of the product and the wall mount.
· Before wall mount, you need not remove the
four rubber feet at the bottom of the main unit, otherwise the rubber feet cannot be fixed back.
Screw length/diameter Depending on the type of wall mounting this wall mount bracket, make sure that you use screws of a suitable length and diameter.
3.5-4mm/0.14″-0.16″
4mm/ 0.16″”
>25mm/0.98″
See the illustration on the quick start guide on how to wall mount the main unit. 1) Drill 2 holes on the wall. Use the supplied
paper template to mark 2 holes on the wall, then secure 2 suitable screws in the holes. 2) Secure the wall bracket on the wall with the dowels and screws. 3) Hook the main unit on the wall bracket.
18 EN
~50mm/2.0″ ”
1
790mm/31.1″
3.5-4mm/0.14″-0.16″
4mm/ 0.16″”
>25mm/0.98″
3
2
8 Product specifications
Note
·
change without notice.
· Total output power: 808W MAX / 410W RMS (1%THD)
· Frequency response (main unit): 150Hz20kHz
· Frequency response (Subwoofer): 35Hz150Hz
· Signal-to-noise ratio: >65 db(CCIR) /(A-weighted)
Audio
· S/PDIF Digital audio input: · Optical: TOSLINK
Bluetooth
· · Bluetooth version: 4.2 · Frequency band/Output power: 2402
MHz _ 2480 MHz / 2dBm
Wi-Fi
· Wi-Fi IEEE 802.11 a/b/g/n · Frequency band: 2.412 – 2.472 GHz,
5.18 – 5.32GHz, 5.50 – 5.70GHz, 5.745 5.825GHz · Radio frequency power transmitted: WiFi 2.4G: 17.6dBm; WiFi 5G: 16.38dBm; WiFi 5.8G: 8.07dBm
Main unit
· Power supply: Model (Philips branded AC power adapter): NSA120EC-19063200
· Input: 100-240 V_, 50/60 Hz, 2.0 A · Output: 19 V 6.32 A · Power consumption: 25 W · Standby power consumption: <0.5 W · Audio channel: 5.1.2 · Built-in speakers: · Central: 2 racetracks full range drivers · Front speaker: 4 full range drivers +
2 tweeters · · · Dimensions (W x H x D):
1049 x 55.6 x 120 mm · Weight: 4.07kg · Operating temperature: 0°C – 45°C
Subwoofer
· Power supply: 220-240 V_, 50/60 Hz · Power consumption: 20 W · Standby power consumption: <0.5 W · Speaker driver: 1 x 8″ subwoofer · Impedance: 3 ohm · Dimensions (W x H x D):
230 x 400 x 407 mm · Weight: 9.6kg · Operating temperature: 0°C – 45°C
Audio codec format
· HDMI: Dolby Digital, Dolby Digital plus, Dolby Digital EX, Dolby TrueHD, Dolby Atmos, DTS, DTS 96/24, DTS-ES, DTS Digital Surround (5.1-ch), DTS-HD High Resolution Audio, DTS-HD Master Audio, DTS ES, DTS: X, IMAX Enhanced
· HDMI eARC: Dolby Digital, Dolby Digital plus, Dolby Digital EX, Dolby TrueHD, Dolby Atmos, DTS, DTS 96/24, DTS-ES, DTS Digital Surround (5.1-ch), DTS-HD High Resolution Audio, DTS-HD Master Audio, DTS ES, DTS: X
· Optical: Dolby Digital, Dolby Digital plus, LPCM 2ch
· Bluetooth: SBC · Play-Fi: MPEG4 AAC, MPEG4 M4A, MP3,
WAV, FLAC, AIFF
19 EN
9 Troubleshooting
Warning
· Risk of electric shock. Never remove the casing of the product.
To keep the warranty valid, never try to repair the product yourself. If you have problems using this product, check the following points before you request service. If you still have a problem, get support at www.philips.com/support
Main unit
The buttons on the main unit do not work. · Disconnect form the power supply for a
few minutes, then connect again.
Sound
No sound from the soundbar speaker. · Connect the audio cable from your
soundbar to your TV or other devices. However, you do not need a separate audio connection when: – the soundbar and TV are connected
through HDMI ARC connection, or – a device is connected to the HDMI IN
connector on your soundbar. · On the remote control, select the correct
audio input. · Make sure that the soundbar is not muted. · Reset this product to its factory settings
(see `Apply factory settings).
No sound from the wireless subwoofer.
·
Read “Pair up with the subwoofer”
section to manually connect the subwoofer to
the main unit.
Distorted sound or echo. · If you play audio from TV through this
product, make sure that the TV is muted.
Audio and video are not synchronized. · Press to synchronize the audio with the
video.
Bluetooth
A device cannot connect with the soundbar.
· The device does not support the compatible profiles required for the soundbar.
· You have not enabled the Bluetooth function of the device. See the user manual of the device on how to enable the function.
· The device is not correctly connected. Connect the device correctly.
· The soundbar is already connected with another Bluetooth device. Disconnect the connected device, then try again.
Quality of audio play from a connected Bluetooth device is poor. · The Bluetooth reception is poor. Move the
device closer to the soundbar, or remove any obstacle between the device and the soundbar.
Wi-Fi
Wi-Fi connection cannot be established. · Check the availability of the WLAN network
on the router. · Place the Wi-Fi router closer to this
product. · Make sure the password is correct. · Check the WLAN function or reboot the
modem and Wi-Fi router.
Dolby Atmos
Cannot achieve outstanding Dolby Atmos effects. · For non-HDMI connections (such as use of
Bluetooth, OPTICAL or AUDIO IN), limited height surround effects are generated. See the section of `Dolby Atmos’ about how to achieve best Dolby Atmos effects.
Play-Fi
Cannot discover the Play-Fi supported devices from the app. · Make sure the device is connected to the
Wi-Fi.
Cannot play Play-Fi music. · Certain network service or contents available
through the device may not be accessible in case the service provider terminates its service.
20 EN
Dolby, Dolby Vision, Dolby Atmos, and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Manufactured under license from Dolby Laboratories. Confidential unpublished works. Copyright © 2012-2020 Dolby Laboratories. All rights reserved.
Use of the Works with Apple badge means that an accessory has been designed to work specifically with the technology identified in the badge and has been certified by the developer to meet Apple performance standards. Apple® and AirPlay® are trademarks of Apple Inc., registered in the U.S. and other countries.
Manufactured under license from IMAX Corporation. IMAX® is a registered trademark of IMAX Corporation in the United States and/ or other countries. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.
The Adopted Trademarks HDMI, HDMI HighDefinition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.
The Wi-Fi CERTIFIEDTM Logo is a registered trademark of Wi-Fi Alliance®.
Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together,DTS:X, and the DTS:X logo are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners.
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS, Inc. (for companies headquartered in the U.S./ Japan/Taiwan) or under license from DTS Licensing Limited (for all othercompanies). DTS, Play-Fi, and the DTS Play-Fi logo are registered trademarks or trademarks of DTS, Inc. in the United States and other countries. © 2020 DTS, Inc. ALL RIGHTS RESERVED.
Chromecast is a trademark of Google Inc. Google Play, and the Google Play logo are trademarks of Google Inc.
To control this AirPlay 2enabled speaker, iOS 11.4 or later is required.
21 EN
2020 © Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong
Limited is the warrantor in relation to this product.
B95_10_UM_V2.0
