www.amazon.com/shops/PEMENOL [email protected]
Bluetooth Stereo Amplifier Board 5V 12V 24V 20W 30W
40W Amp Receiver Board with Infrared Remote Control
Pic1.1
GENERAL INFORMATION:
The item is a high-power stereo Bluetooth audio module, with dual channels audio signal output and built-in amplifier module, Therefore it can be connected to loudspeaker directly. It is ideal for DIY wireless Bluetooth speakers, amplifier equipment, Car Bluetooth device, etc.
FUNCTION OVERVIEW
- Width work voltage range
- Applicable multiple type speakers
- Knob adjustment
- Support reverse connection protection
- Support short circuit protection
- Self-recovery overheat protection
- Support remote control
PARAMETERS:
| Item Name | Stereo Bluetooth Power Amplifier Module |
| Work Voltage | DC 5V-24V |
| Communication distance | 15meter(Max) |
| Channel | Dual channel |
| Output Power(at 1KHz) | Output power 20W*2 at 12V 4ohm |
| Output power 30W*2 at 16V 4ohm | |
| Output power 30W*2 at 21V 8ohm | |
| Output power 40W*2 at 24V 8ohm | |
| Match speaker(40W~200W) | 4ohm at 5V~16V |
| 4ohm at 5V~16V | |
| Work Temperature | -40℃~85℃ |
| Work Humidity | 0%~95%RH |
| Size of the Module | 55*38*14mm |
| Size of Remote Controller | 86*40*7mm |
USE STEPS:
- Choose the proper speaker and connect as shown in wiring diagram. (refers to Pic2.1)
- Connect to DC 5V-24V power supply from input terminal. Blue LED indicator flashing means module enters into Bluetooth mode, then pairing mode after broadcasting the “Beep”.
- Turn ON Bluetooth in phone.
- Search Bluetooth device `XY-P40W’ in your Bluetooth device listing.(refers to Pic2.3)
- LED indicator will keep ON and it means that module is successfully connected and is waiting for playing.
- Module will play music after selecting music in the phone. LED indicator will keep slowly blinking.
- Increase volume by turn right potentiometer.
- Decrease volume by turn left potentiometer.
- Press potentiometer to play or pause music.
*The remote control also can control module. (refers to Pic2.2) - Module will broadcast the “beep” if disconnected.
Function Introduction
Pic2.1
Pic2.2
Pic2.3
- Connect power supply.
- Bluetooth Pairing (Blue LED indicator flashing means module enters Bluetooth mode, then pairing mode After broadcasting the “Beep”; Search and connect the bluetooth named “XY-P40W” (power amplifier board device name) on your phone. It will “Beep” if successful.
- Play the music (Play the music in your phone once the LED indicator is keeping ON), then the LED indicator is slow when playing music.
- Standby. The amplifier board is stand by for next pairing after the Bluetooth is disconnected, then it enters the pairing mode and waits for pairing after broadcasting the “beep”.
*CAUTION:
- The power amplifier board should be as far away as possible from the WIFI signal (router) , in order to avoid signal interference.
- Recommended power supply voltage is DC 5 ~24V. Module will be damaged of input voltage is more than 26v.
- Input voltage can not more than 16V if connect 40hm speaker.
- Input voltage can not more than 24V if connect 80hm speaker.
- It is recommended to use a power supply of 2A or higher.
- Please don’t use extra long wires to avoid signal interference.
- It is recommended to use a speaker above 40W to avoid speaker damage.
- Please read user manual and description before use.
PACKAGE:
- >.1pcs XY-P40W Stereo Bluetooth Power Amplifier Module
- >.1pcs Remote control
- >.2pcs Acrylic shell
- >.4pcs Copper column
- >.8pcs screw
AFTER-SALES:
*We have always been keen to provide customers with the best quality service at the most competitive price.
*Looking forward to get progress and growth with all of you.
*For more product questions and inquiries, please send your advice to [email protected]
*Thank you for your purchase!