CLASSIC
MLF13 Instruction Manual
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ THE ENTIRE MANUAL PRIOR TO USE
Before getting started, let’s make sure this mount is perfect for you!
- Does your TV weigh more than 130 lb (58.9 kg) including accessories?
No — Perfect!
Yes — This mount is NOT compatible. Visit MountFinder.Sanus.com or call 1-800-359-5520 (UK: 0800-056-2853) to find a compatible mount. - What is your wall made of?
Drywall with perfect! wood studs?
Unsure? Call 1-800-359-5520 (UK: 0800-056-2853) - Do you have all of the tools needed?
- Ready to begin?
Please read through these instructions completely to be sure you’re comfortable with this easy install process. Also, check your TV
owner’s manual to see if there are any special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the installation, assembly, or use of this product, contact
Customer Service at 1-800-359-5520 (UK: 0800-056-2853).
CAUTION: Avoid potential personal injuries and property damage!
● This product is designed for use in wood stud walls – DO NOT install into drywall alone
● The wall must be capable of supporting five times the weight of the TV and mount combined
● Do not use this product for any purpose not explicitly specified by the manufacturer
● Manufacturer is not responsible for damage or injury caused by incorrect assembly or use
Dimensions in. [mm]
Parts and Hardware
WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service.
Never use damaged parts!
NOTE: Not all hardware included will be used.
Parts and Hardware for STEP 1
Parts and Hardware for STEP 2
Parts and Hardware for STEP 3
Additional Hardware
STEP 1 Attach Brackets to TV
1-1 Select TV Screw Diameter
Hand thread screws into the threaded inserts on the back of your TV to determine which screw diameter (M5, M6, or M8) to use.
1-2 Select TV Screw Length
If your TV has a flat back AND you want your TV closer to the wall, use the shorter screws (a).
Use the spacers and longer screws (b) to accommodate:
- Round/irregular back TVs
- TVs with inset mounting holes
- Extra space needed for cables
Standard configurations are shown. For special applications, or if you are uncertain about your hardware selection, contact Customer Serviceat 1-800-359-5520.
CAUTION:
Verify adequate thread engagement with the screw or screw/spacer combination.
– Too short will not hold the TV.
– Too long will damage the TV.
1-3 Attach L/R TV Interface Brackets
Ensure that your brackets are centered and level on the back of the TV. Secure brackets using your screw/washer (Flat Back) or screw/washer/
spacer (Round Back / Extra Space) selection.
1-4 Attach Horizontal TV Interface Brackets
Ensure horizontal brackets 14 15 are centered and screws 16 are securely fastened.
STEP 2 Attach Wall Plate to Wall Wood Stud
CAUTION: Avoid potential personal injuries and property damage!
- Drywall covering the wall must not exceed 5/8 in. (16 mm)
- Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
- Minimum horizontal space between fasteners: 16 in. (406 mm)
- Locate your stud. Verify and mark the center of the stud by finding the stud edges using an awl, a thin nail, or an edge to edge stud finder.
- Level the wall plate 17 and mark your hole locations.
- Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
IMPORTANT: Be sure to drill into the center of the studs.
IMPORTANT: Pilot holes must be drilled to a depth of 3 in. (75 mm). - Install wall plate 17 using four lag bolts 18 and four washers 19 . Tighten the lag bolts only until they are pulled firmly against the wall plate.
CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.
STEP 3 Attach Arm Assembly to Wall Plate/Attach TV to Arm Assembly
- Hang the arm assembly 20 onto the wall plate 17 .
- Install the wall plate screws
21 using the 3/16 in. hex key 24 .
CAUTION: Avoid potential injuries or property damage! Ensure the wall plate screws 21 are secure. Periodic tightening may be required.
- Hang the TV/bracket assembly onto the arm assembly 20 . Level the TV/bracket assembly and install the washer 23 and locking screw 22 .
CAUTION: Avoid potential injuries or property damage! Be sure to install the washer 23 and locking screw 22 securely. This will prevent the TV from separating away from the mount.
Manage Cables
Adjustments
Thank you for choosing Sanus Classic! Please take a moment to let us know how we did:
Call us: 1-800-359-5520
UK: 0800 056 2853
Email us: [email protected]
Leave a review: sanus.com
Find us on Facebook: SANUS
Follow us on Twitter @sanussystems
Legrand AV Inc. and its a¼liated corporations and subsidiaries (collectively, “Legrand”), intend to make this manual accurate and complete. However, Legrand AV makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Legrand AV makes no representation of warranty, expressed or implied, regarding the information contained herein. Legrand AV assumes no responsibility for accuracy, completeness or su¼ciency of the information contained in this document.
©2020 Legrand AV Inc. All rights reserved. Sanus is a division of Legrand AV.
All other brand names or marks are used for identification purposes and are trademarks of their respective owners.
SANUS • 6436 City West Parkway • Eden Prairie, MN 55344 USA
6901-602526 00