Overview

Using your BT969 True Wireless Earphones

Before use: Charge both earbuds by placing it inside the charging case and press the button on the front of the case once to start charging.

Turn off the Bluetooth function from your music device. eg. Mobile phone or music device.

Take out the earbuds from the charging case after they have charged, it will turn on automatically, even it is not charging. If earbuds are not powered on, press and hold the power button on the two earbuds at the same time for about 3 seconds until the blue and red lights start to flash. Then release

Wait about 8-10 seconds for the two earbuds to connect to each other automatically. If the two earbuds are not pairing, quick double press on the left earbud, and wait about 8 seconds for pairing. One of the earbuds will be flashing red+blue, and another side of earbud will be flashing blue.

You can now turn on the Bluetooth function of your mobile phone. search and select BT969. Wait. 5 seconds. Both earbuds will have no lights flashing and a voice will sound “Connected’: then it is ready to use with your device.

To use your Wireless Earphones After setting them up

Turn off the Bluetooth function on your phone or device and then Press the power-on button on both earbuds for 3 seconds at the same time to turn them on.

Wait 8 seconds for them to connect to each other automatically.

Autopair: Alternatively, If both earbuds are inside the charging case. Press the
charging/awake button (Fig.2) on the front of the case. A blue light will turn on indicating the earbuds are awake.
Remove the earbuds from the case, wait 3 seconds, and it will be ready to pair with your Bluetooth device.

Turning off the earbuds

Press and hold the left earbud and right earbud at the same time for about 3 seconds and the earbuds will be powered off (Fig. 1)

Charging the Earphones

a) Power off the earbuds and then put both earbuds inside the Charging Case.
b) The case will charge the earbuds automatically after you put both earbuds inside the charging case, or press the button on the front of the case to start charging (Fig.2). A blue light will show that it is charging (Fig.3) Before charging the earbuds make sure the charging case is fully charged – see point 5 below.

Note: It will take approximately 1 .5 hours to charge the earbuds. The Charging case will automatically stop charging when the earbuds are fully charged. To stop charging the earbuds at anytime, press the charging button again.

Case Charging

Plug the charging cable to the case. Red light flashing indicates charging, charge for minimum 2 hours. ( The charging case must be fully charged in order to charge the earbuds )

Music functions

When you are listening to the music, short press the button on either earbud: one for music playing, one for music pause.
When the earbuds are approaching very low battery power, one of the earbuds will turn off to save power while the other will continue to play.

Phone calls

Picking up a phone call – short press the button on the left earbud to answer the phone call and short press again to end the call. Double Long press (2sec) to reject the call.

Trouble Shooting

In the event that your True Wireless Is not connecting to your device.

1. Make sure both earbuds are fully charged.
2. The music device is not more than 5 meters away from the phone and free from interference from other Bluetooth devices.
3. If the earbuds are on, turn them off by pressing the power button for 3 seconds, and follow Steps 1 – 4 again to reconnect the earbuds and the phone.

If only one earphone Is wor1dng

• Make sure both units are properly charged
• The mobile or music device is no more than 5 meters away from the buds.
• Reset your ear buds by following steps 1 – 4.

If the volume is low

1. Turn up the volume on your device
2. Make sure the your mobile device is fully charged and within 5 meters range.

If earbuds are not charging or not holding a charge.

1. Make sure the charging case is fully charged. See point 5
2. Place the earbuds inside charging case and press the button on the front of the case once. A blue light will show indicating that it is charging the earbuds.
3. Always turn off the earbuds before putting them back in the charging case. Press the button on both earbuds for 3 seconds to power off. (Fig.1)

Specifications

• Model Number: BT969
• Bluetooth Version: 5.0
• Earphone Battery capacity: 40mah+40mah=80mah
• Case Battery capacity: 200mah
• Power Input: DCSV /200MA
• Protocol: HFP/HSP/ A2DP/AVRCP/GAVDP/IOPT
• Works with Bluetooth enabled devices version 3 and above

Limited 90-Day Warranty

Sentry warrants this product to be free from defects in materials and workmanship for 90 days from the date of original purchase. This warranty does not pertain to damage resulting from accident, abnormal use, misuse or neglect Any defective product will be replaced if returned to an authorized Sentry dealer or to Sentry directly at: PO Box 885, One Bridge Street, Hillburn, NY 10931. Please enclose a $5 check for return shipping.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC ID: 2ACP4BT969 Model# BT969

• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.

Sentry Industries inc declares that radio equipment BT969 is in compliance with Directive 2014/53/EU. The EU declaration of conformity is available at
https://sentryindustries.com/european-declaration-of-conformity/

Conformity with Directives
This product is CE marked to denote conformity with Directives 73/23/EEC
(low voltage) and 89/336/EEC
(Electromagnetic Compatibility) , as amended.

Environmental Protection
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

BC BT969

WIRE-FREE
EARBUDS

Using your BP369True Wireless Earphones

Before use: Charge both earbuds by placing them inside the charging case and press the button on the front of the case once to start charging.

STEP 1 Turn off the Bluetooth function from your music device. eg. Mobile phone or music device.
STEP 2 Take out the earbuds from the charging case after they have charged, it will turn on automatically, even it is not charging. If earbuds are not powered on, press and hold the power button on the two earbuds at the same time for about 3 seconds until the blue and red lights start to flash. Then release
STEP 3 Wait about 8-10 seconds for the two earbuds to connect to each other automatically. If the two earbuds are not pairing, quickly double press on the left earbud, and wait about 8 seconds for pairing. One of the earbuds will be flashing red+blue, and another side of the earbuds will be flashing blue.
STEP 4 You can now turn on the Bluetooth function of your mobile phone. Search and select BT969. Wet 5 seconds. Both earbuds will have no lights flashing and a voice will sound “Connected; then it is ready to use with your device.

Using your BT969 True Wireless Earphones

To use your Wireless Earphones After setting them up
Turn off the Bluetooth function on your phone or device and then press the power-on button on both earbuds for 3 seconds at the same time to turn them on.

Wait 8 seconds for them to connect to each other automatically. Auto pair: Alternatively, If both earbuds are inside the charging case. Press the charging/awake button (Fig.2) on the front of the case. A blue light will turn on indicating the earbuds are awake.
Remove the earbuds from the case, wait 3 seconds, and it will be ready to pair with your Bluetooth device.
Then turn on your Bluetooth function on your device and it should automatically pair with the BT969 earbuds.

Turning off the earbuds

Press and hold the left earbud and right earbud at the same time for about 3 seconds and the earbuds will be powered off (Fig.1)

Charging the Earphones

1. Power off the earbuds and then put both earbuds inside the Charging Case.
2. The case will charge the earbuds automatically after you put both earbuds inside the charging case, or press the button on the front of the case to start charging (Fig.2). A blue light will show that it is charging (Fig.3) Before charging the earbuds make sure the charging case is fully charged – see point 5 below.
   Note: It will take approximately 1.5 hours to charge the earbuds. The Charging case will automatically stop charging when the earbuds are fully charged. To stop charging the earbuds at any time, press the charging button again.

 Case Charging

Plug the charging cable into the case. Red light flashing indicates charging, charge for minimum 2 hours. ( The charging case must be fully charged in order to charge the earbuds) The charging complete the red flashing indicate will be changed to solid.

Music functions

When you are listening to the music, short press the button on either earbud: one for music playing, one for music pause.

When the earbuds are approaching very low battery power, one of the earbuds will tum off to save power while the other will continue to play.

Phone calls.

Picking up a phone call – short press the button on the left earbud to answer the phone call and short press again to end the call. Double Long press (2sec) to reject the call.

Trouble Shooting

In the event that your True Wireless Is not connecting to your device.

1. Make sure both earbuds are fully charged.
2. The music device is not more than 5 meters away from the phone and free from Interference from other Bluetooth devices.
3. If the earbuds are on, turn them off by pressing the power button for 3 seconds, and follow Steps 1 – 4 again to reconnect the earbuds and the phone.

If only one earphone Is working

1. Make sure both units are properly charged
2. The mobile or music device is no more than 5 meters away from the buds.
3. Reset your earbuds by following steps 1 – 4.

If the volume Is low

1. Turn up the volume on your device
2. Make sure your mobile device is fully charged and within 5 meters range.

If earbuds are not charging or not holding a charge.

1. Make sure the charging case is fully charged. See point 5
2. Place the earbuds inside the charging case and press the button on the front of the case once. A blue light will show indicating that it is charging the earbuds.
3. Always tum off the earbuds before putting them back in the charging case. Press the button on both earbuds for 3 seconds to power off. (Fig.1)

If after some time, the earbuds not pairing correctly.

1. Delete the earbuds from your phone by going to the phone’s Bluetooth settings.
2. Reset the earbuds by long-pressing both buttons on the earbuds for 10 seconds.
3. Follow Steps 1-4 on the first page of this manual to repair your earbuds to your phone device. Also, it is good to check that the earbuds and charging case are fully

Specifications:

Model Number: BT969

• Bluetooth Version:5.0
• Earphone Battery capacity: 40mah+40mah=80mah
• Case Battery capacity: 200mah
• Power Input: DCSV/200MA
• Protocol: HFP/HSP/A2DP/AVRCP/GAVDP/IOPT
• Works with Bluetooth enabled devices version 3 and above Communication system: Bluetooth Specification version 5.0
• Operating temperature:0 °C to 40 °C
• Radio Frequency: 2.402 GHz-2.480 GHz
• RF Output Power -2.025 dBm (Max)

Limited 90-Day Warranty:

Sentry warrants this product to be free from defects in materials and workmanship for 90 days from the date of original purchase. This warranty does not pertain to damage resulting from accidents, abnormal use, misuse, or neglect. Any defective product will be replaced if returned to an authorized Sentry dealer or to Sentry directly at PO Box 885, One Bridge Street, Hillburn, NY 10931. Please enclose a $5 check for return shipping.

FCC ID: 2ACP4-BT969 Model # BT969

Sentry Industries inc declares that radio equipment BT969 is in compliance with Directive 2014/53/EU. The EU declaration of conformity is available at https://sentryindustries.com/european-declaration-of-conformity/

Confirm ity with Directives
This product is CE marked to denote conformity with Directives 73/23/EEC (low voltage) and 89/336/EEC (Electromagnetic Compatibility), as amended.

Environmental Protection
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sentry Industries Inc is under license. Other trademarks and trade names are those of their respective owners.

Supplier’s Declaration of Conformity 47 CFR 47 CFR Part 15.21, 15.105(b)
Compliance Information
Sentry Bluetooth Earphone and Headphone
Responsible Party –
Sentry Industries Inc
One ridge street, Hillburn, NY 10931
Tel +1 843 753 2910

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and12) this device must accept any interference received, inducing interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class 8 digital device, pursuant to part 15 of the FCC Rules. These knits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radiocommunication.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
• Consult the dealer or an experienced radio/TV technician for help

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.”

SENTRY Safes with electronic lock

Thank you for purchasing this Sentry product.

For safes with key lock only

Your Sentry safe is equipped with a high security, 8 lever key lock, two (2) keys are provided.

For safes with electronic lock

Battery Installation

To power the lock, four alkaline AA batteries (not included) are required.

NOTE: Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED.

To install batteries, remove keypad by rotating the cover counterclockwise, then pulling toward you. (Fig. A) Unlock door with the override key provided in the plastic bag attached to the owner’s manual, and open the door using the lever handle. Remove key hook plate located on the inside back of the door by sliding the plate upward, then pulling toward you. (Fig. B) Insert the four batteries as indicated. Replace the key hook plate and keypad.

Test first with door open!

(See back cover of this manual for your factory code.)

Test your combination several times with the door open.

NOTE: All electronic lock units have been provided with an override key (skeleton key). Some electronic units are equipped with a handle OR electronic lock and key.

1. Insert the four-bitted key into the lock to the left of the key pad. (Be sure key lock is turned as far left as possible.)
2. Press the five-digit factory code. The green light will come on.
3. For units with key, turn the key to the right.
4. Open the door.

Using the keypad

Only a light touch is needed. A green PROCEED light and a single beep indicate that the keypad “felt” your touch. The lock allows 5 seconds for each key press. If you pause longer, an error signal will occur (blinking red light and three beeps), indicating you should start over.

Access Codes

There are three possible ways to unlock and access the safe—by entering its preset Factory Code, your own User Code or a Passcode.

You can always open the safe by entering the 5-digit Factory Code. But if you prefer to use your own code, you can program the safe to open to the 5-digit User Code of your choice. If you wish to give someone else temporary access to the safe, you can program a passcode that can later be erased.

Programming a user code

There are two ways to program a user code.

A

1. Press the Program key.
2. Enter the Factory Code. The green LED remains ON while you enter the 5-digit user code of your choice. After 5 digits are entered the green LED turns OFF.
   (To enter a new User Code, repeat these steps.)

B

1. Press the red button inside the safe. The lock will “beep” and the green LED will come on.
2. Enter a 5-digit user code.
   (To enter a new User Code, repeat these steps.)

Programming a passcode

1. Press the Program key twice.
2. Enter your 5-digit User Code. The green LED remains ON.
3. Enter the 5-digit passcode of your choice (any combination except 00000.) After 5 digits are entered, the green LED turns OFF.
   (To enter a new passcode, repeat these steps. To erase the passcode, press Program twice, enter your User Code and then enter 00000.)

Unlocking

To unlock the safe, you must enter a valid Factory Code, User Code or Passcode.
Once you have done this, you have 4 seconds to open the safe by turning the handle or 4-bitted key to the unlock position. If you fail to do so in time, the lock will reactivate.

(If you realize you have made an error while entering your code, press the CLEAR button and start over.)

Key override

If your electronic lock fails or you do not have any codes available, you may use a key override to access this unit. Remove the keypad by rotating the cover counterclockwise, then pull toward you. Unlock the door by inserting the key provided into the hole and turning clockwise. Open the door. Do not lock override key inside of unit.

Signals

Your electronic-lock safe communicates by means of several audio/visual signals.
Red (Error) LED + three beeps indicates one of the following:

1. You have pressed Program key out of sequence
2. You have entered an invalid code or passcode.
3. You have let 5 seconds or more elapse between key entries.

Green (Proceed) LED + single beep occurs

1. After entering each digit of Factory or User Code, or Passcode
2. After pressing Clear key
3. After pressing Program key

Green LED only

1. Comes ON after you enter a valid code/passcode and remains lit during the 4-second period in which the safe can be opened.
2. Comes ON in the Program User Code mode after you enter the Factory Code and remains lit until you have finished entering a 5-digit User Code.
3. Comes ON in the Program Passcode mode after you have entered your
   User Code and remains ON until you have entered a 5-digit passcode. Indicates “low battery” and will typically not turn OFF until new alkaline batteries are installed.

Your electronic lock automatically performs a low battery test during each lock use.
If a “low battery” condition is detected, the Yellow LED will come ON and remain ON during each subsequent lock operation. (The lock will continue to function in a Low Battery state, until battery failure.) The Yellow LED will turn OFF only after three consecutive “Good Battery” readings or after the low batteries are replaced.
(Note: When the new batteries are installed, the Yellow LED may come ON and stay ON during the first lock operation before it returns to OFF.)

NOTE: When changing the batteries, you must use the factory code to open (See back cover.) Passcode will have to be re-programmed.

Delay Mode

The lock automatically enters a two-minute Delay Mode after an invalid code has been entered three consecutive times. In this mode, the lock cannot be activated and any key entry will generate an ERROR signal.

Bolt-down Instructions

1. Select a suitable and convenient location for your safe. Set the safe in place and use the holes provided in the bottom or back of the safe to mark the location of the holes to be drilled in the floor or wall. It is not recommended to attempt to bolt to both floor and wall. If bolting to a wall, please ensure that the safe is resting on a supporting surface, i.e. floor, table or shelf.
2. Move the safe away and drill holes of the appropriate diameter and depth for the type of hardware being used and the mounting surface.
3. Place the safe back over the holes and install the fasteners as required.
4. NOTE: For maximum security on models which have feet, remove feet before bolting to floor.

Sentry Gun and Executive Safes Owners Manual

•••IMPORTANT•••

DO NOT RETURN SAFE TO THE STORE!

If you experience problems or challenges with your safe, please contact us. Many issues can be resolved quickly the product being returned.

www.sentrysafe.com

900 Linden Avenue / Rochester, New York / 14625-2784 USA
Customer Service: 1-800-828-1438
Fax: 585-381-2940

Thank you for purchasing this SentrySafe gun safe product.

Please read this manual before using this product.

We are pleased that you have chosen one of our gun safes to protect your firearms. You can be assured that your safe meets the California Department of Justice standards for firearm safety. This manual will provide you with the information you need to:

• unpack and set up your safe
• open the safe
• operate the lock
• take full advantage of your safe’s special features.

Remember to keep your combination a secret. Writing down a combination and putting it in a desk drawer is like leaving your door key under the mat – it invites entry.

Please retain this manual for your records. If you have any questions about your gun safe, please visit our website at www.sentrysafe.com or call Sentry Customer Service at 1-800-828-1438 or 1-585-381-4900. Customer Service representatives are ready to assist you, 8 a.m. to 6 p.m., E.S.T., Monday – Friday.

Unbolting your gun safe from the shipping pallet

WARNING! UNBOLTING YOUR GUN SAFE FROM THE SHIPPING PALLET!

This is a two-person operation and should not be attempted without help. Before attempting to unbolt your new safe, be certain someone is with you to help steady the safe while you work. Ensure the safe is standing upright on a flat, level surface. (Fig. A)

Tools/equipment required

• Adjustable wrench, pliers, or 17 mm (11/16”) socket wrench
• Hammer

1. Using a wrench or pliers, remove the nuts located under the X-cut in the carpet in the bottom of the unit. (Fig. B)
   NOTE: If the bolts turn when you begin to remove the nuts, reach between the slats of the pallet and hold the bolts, by hand and/or with pliers, as you turn the nuts.
2. Once the nuts are removed, use a hammer to tap the bolts through the bottom of the safe.
3. Close door and put handle in locked position.
4. With your helper, slide safe to one edge of pallet. Tip the safe so that the edge moves to the floor. (Fig. C)
5. Remove the pallet and stand the safe upright on the floor.

Bolt-down instructions

To help provide maximum security, SentrySafe strongly recommends this safe be bolted down. (Hardware supplied)

1. Select a suitable and convenient location for your safe. Set the safe in place and use the holes provided in the bottom or back of the safe to mark the location of the holes to be drilled in the floor or wall. It is not recommended to attempt to bolt to both floor and wall. If bolting to a wall, please ensure that the safe is resting firmly on the floor.
   Note: Fire-Safe models cannot be bolted to the wall.
2. Move the safe away and drill holes of the appropriate diameter and depth for the type of hardware and the mounting surface being used (2 each – bolts, washers and masonry anchors).
3. Place the safe back over the holes and install the fasteners as required. If a water resistant unit was purchased, rubberized washers are provided. Assure that the area around the safe hole opening is clean using a damp cloth. Place the rubber side of the washer facing down against the safe floor and install the fastener.
   NOTE: SentrySafe is not responsible for any costs incurred if unit is to be replaced.

Lock instructions

Gaining Entry into Safes with Combination Locks

3-Number Combination Lock and Dual Combination Key Lock

NOTE: See the sticker on the back cover of this manual for your combination.

IMPORTANT: The lock on this safe is in the open position. DO NOT operate the combination until first reading and understanding the following instructions.

Test first 

WITH DOOR OPEN!

Test your combination several times with the door open.

To unlock and open

Before dialing your combination, simply insert the key (if equipped) in the lock and turn clockwise.

1. Start the dial at ZERO.
2. Turn the dial to the left. Make sure ZERO passes the pointer at least THREE times. Then stop at the first number of your combination.
3. Turn the dial to the right. Stop the SECOND time you reach the second number of your combination.
4. Turn the dial to the left. Stop the FIRST time the pointer reaches the third number of your combination.

To Close and Lock

With the door closed, turn the handle counterclockwise to secure the locking bolts, then spin the combination dial to the left at least four times to scramble the combination.

Gaining Entry into Safes with Electronic Locks

Standard Electronic Lock and Dual Electronic Key Lock

To activate lock:

Four alkaline AA batteries, Voltage: 6Vdc, (not included) are required to activate the keypad.

NOTE: Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED.

To install batteries:

1. Using two hands, hold the keypad, thumbs down, on its left and right sides. Push up the keypad with your thumbs, and disconnect it from the safe by pulling it towards you. (Fig. A)
2. Let the disengaged keypad hang by its wires. This will expose the battery holder. (Fig. B)
3. Install four alkaline AA batteries as illustrated on the back of the battery holder.
4. Reconnect the keypad by inserting the keypad’s four posts into the matching holes.
5. Push down to snap into place.

Test first
WITH DOOR OPEN!

(See back cover of this manual for your factory code.)

Test your factory code several times with the door open.

NOTE: Only a light touch is needed. A green PROCEED light and a single beep indicate that the keypad “felt” your touch. The lock allows 5 seconds for each key press. If you pause longer, an error signal will occur (blinking red light and three beeps), indicating you should start over.

For safes with dual combination key lock insert key and turn clockwise.

1. Press the 5-digit factory code. The green light will come on.
2. Turn the handle clockwise and open the door.

Access codes

There are three possible ways to unlock and access the safe—by entering its preset Factory Code, your own User Code or a User PIN (Personal Identification Number).

You can always open the safe by entering the 5-digit Factory Code. This code cannot be deleted.

But if you prefer to use your own code, you can program the safe to open to the 5-digit User Code of your choice. If you wish to give someone else temporary access to the safe, you can program a User PIN that can later be erased.

Programming a user code

There are two ways to program a user code.

A

1. Press the Program key. (Prog.)
2. Enter the Factory Code. The green LED remains ON while you enter the 5-digit user code of your choice. After 5 digits are entered the green LED turns OFF.
   (To enter a new User Code, repeat these steps.)

B

1. Press the red button on inside of door (hinge side). The lock will “beep” and the green LED will come on.
2. Enter a 5-digit user code.
   (To enter a new User Code, repeat these steps.)

Keep your new user code secure

For your records, please copy it here:

_____ _____ _____ _____ _____

Programming a user PIN

1. Press the Program key.
2. Press it a second time.
3. Enter your 5-digit User Code. The green LED remains ON.
4. Enter the 5-digit User PIN of your choice (any combination except 00000.) After 5 digits are entered, the green LED turns OFF.

(To enter a new User PIN, repeat these steps. To erase the User PIN, press Program twice, enter your User Code and then enter 00000.)

Key override

If your electronic lock fails or you do not have any codes available, you may use a key override to access this unit.

1. Using two hands, hold the keypad, thumbs down, on its left and right sides. Push up the keypad with your thumbs, disconnect and remove the battery holder.
2. Insert the skeleton key into the key hole inside the opening for the battery.
3. Turn the key to the right.
4. Open the door.

Signals

Your electronic-lock safe communicates by means of several audio/visual signals.

Red (Error) LED + three beeps indicates one of the following:

1. You have pressed Program key out of sequence.
2. You have entered an invalid code or user pin.
3. You have let 5 seconds or more elapse between key presses.
4. Lights after three consecutive invalid codes are input (2-minute delay mode).

Green LED only:

1. Comes ON after you enter a valid code and remains lit during the 4-second period in which the safe can be opened.
2. Comes ON in the Programming mode and remains lit until you have finished entering a 5-digit code.

Yellow LED only:

1. Comes ON when the batteries need to be replaced.

Delay mode

The lock automatically enters a 2-minute Delay mode after an invalid code has been entered three consecutive times. In this mode, the lock cannot be activated and any key entry will generate an ERROR signal.

Sentry Group Customer Care

Using the keypad on electronic safes

Caution! Liquids can damage the keypad!

Caution! Pen points or other sharp objects can puncture the keypad membrane!

Fire ratings

To be sure your safe performs as rated and complies with its ratings, remove it from the pallet before installation.

ETL verified fire claim for all models except GM1055C/E + EM1055E

Verified by ETL SEMKO to meet manufacturer’s specification for fire resistance 1400°F (760°C) for 30 minutes endurance.

ETL verified fire claim for GM1055C/E + EM1055E

Verified by ETL SEMKO to meet manufacturer’s specification for fire resistance 1200°F (649°C) for 20 minutes endurance.

Lost keys or combination

First, find your safe’s Serial Number. The Serial Number is printed on the small label on the right side and the back side of the safe (outside). Send this and a check or money order for $15.00 (U.S. funds) ($15.00 for keys and $15.00 for combinations). Please include a written statement of ownership witnessed and signed by a notary public or bank official. The notary must have a different last name than the owner.

Mail to: Sentry Group, Dept. 200, 882 Linden Avenue, Rochester, NY 14625-2784, USA, or fax statement (notary seal must be legible) to 1-585- 381-2940. Payment may also be made using your VISA or Mastercard credit card by phone only. Call 1-800-828-1438 to make credit card payment. Do not fax credit card information.

NOTE: Prices subject to change without prior notification.

WARNING!

DO NOT store your safe on the pallet on which it was shipped.
SentrySafe gun safes which are ETL-tested and verified, will not comply with their ratings if the safe is stored on the shipping pallet.

WARNING!

If children live or visit in your home, do not leave your SentrySafe Gun Safe or Executive Safe open and unattended. Children at play could accidentally be locked inside the safe.
Keep your safe closed and locked at all times.

Using your BT980 True Wireless Earphones

Before use: Charge both earbuds by placing it inside the charging case.

STEP 1 Turn off the Bluetooth function from your music device. eg  Mobile phone or music device.
STEP 2 Take out the earbuds from the charging case after they have charged, it will turn on automatically, even it is not charging. If earbuds are not powered on, press and hold the power button on the two earbuds at the same time for about 3 seconds until the blue and red lights start to flash. Then release
STEP 3 Wait about 8-10 seconds for the two earbuds to connect to each other automatically. If the two earbuds are not pairing, quickly double press on the left earbud, and wait about 8 seconds for pairing. One of the earbuds will be flashing red+blue, and another side of the earbuds will be flashing blue.
STEP 4 You can now turn on the Bluetooth function of your mobile phone. Search and select BT980. Wait 5 seconds. Both earbuds will have no lights flashing and a voice will sound “Connected”, then it is ready to use with your device.

Using your True Wireless Earphones

To use your Wireless Earphones After setting them up
Turn off the Bluetooth function on your phone or device and then press the power-on button on both earbuds for 3 seconds at the same time to turn them on. Wait 8 seconds for them to connect to each other automatically.

Turning off the earbuds

Press and hold the left earbud and right earbud at the same time for about 3 seconds and the earbuds will be powered off.

Charging the Earphones

1. Power off the earbuds and then put both earbuds inside the Charging Case.
2. The case will charge the earbuds automatically after you put both earbuds inside the charging case, Red light on the earbuds will show they are charging.
   Before charging the earbuds make sure the charging case is fully charged – see point 5 below.

Note: It will take approximately 1.5 hours to charge the earbuds. The Charging case will automatically stop charging when the earbuds are fully charged.

Case Charging

Plug the charging cable into the case. Blue light flashing indicates charging, charge for minimum 2 hours. ( lf the charging case is not charged, the earbuds will be kept on or will turn on when placed inside the case. The charging case must be fully charged in order to charge the earbuds.)

Music functions

When you are listening to the music, short press the button on either earbud: one for music playing, one for music pause.
When the earbuds are approaching very low battery power, one of the earbuds will turn off to save power while the other will continue to play.

Phone calls.

Picking up a phone call – short press the button on the left earbud to answer the phone call and short press again to end the call. Double Long press (2sec) to reject the call.

Trouble

In the event that your True Wireless is not connecting to your device.

1. Make sure both earbuds are fully charged.
2. The music device is not more than 5 meters away from the phone and free from interference from other Bluetooth devices.
3. If the earbuds are on, turn them off by pressing the power button for 3 seconds, and follow Steps 1 – 4 again to reconnect the earbuds and the phone.

If only one earphone is working

1. Make sure both units are properly charged
2. The mobile or music device is no more than 5 meters away from the buds.
3. Reset your earbuds by following steps 1 – 4.

If the volume is low

1. Turn up the volume on your device
2. Make sure your mobile device is fully charged and within 5 meters range.

If earbuds are not charging or not holding a charge.

1. Make sure the charging case is fully charged. See point 5
2. Place the earbuds inside the charging case and press the button on the front of the case once. A blue light will show indicating that it is charging the earbuds.
3. Always turn off the earbuds before putting them back in the charging case.
   Press the button on both earbuds for 3 seconds to power off.

If after some time, the earbuds are not pairing correctly.

• Delete the earbuds from your phone by going to the phone’s Bluetooth settings.
• Reset the earbuds by long-pressing both buttons on the earbuds for 10 seconds.
• Follow Steps 1-4 on the first page of this manual to repair your earbuds to your phone device. Also, it is good to check that the earbuds and charging case are fully charged.

Specifications:

• Model Number: BT980
• Bluetooth Version: 5.0
• Earphone Battery capacity: 50mah+50mah=100mah
• Case Battery capacity: 300mah
• Power Input: DC5V/200MA
• Protocol: HFP/HSP/A2DP/AVRCP/GAVDP/IOPT
• Works with Bluetooth enabled devices version 3 and above
• Communication system: Bluetooth Specification version 5.1
• Operating temperature: 0 °C to 40 °C
• Radio Frequency: 2.402 GHz-2.480 GHz

Limited 90-Day Warranty: Sentry warrants this product to be free from defects in materials and workmanship for 90 days from the date of original purchase. This warranty does not pertain to damage resulting from accident, abnormal use, misuse or neglect. Any defective product will be replaced if returned to an authorized Sentry dealer or to  Sentry directly at PO Box 885, One Bridge Street, Hillburn, NY 10931. Please enclose a $5 check for return shipping.

FCC ID: 2ACP4-BT975 Model # BT980

The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sentry Industries Inc is under license. Other trademarks and trade names are those of their respective owners. Sentry Industries inc declares that radio equipment BT980 is in compliance with Directive 2014/53/EU.The  EU declaration of conformity is available at https://sentryindustries.com/european-declaration-of-conformity/ Conformity with Directives
This product is CE marked to denote conformity with Directives 73/23/EEC (low voltage) and 89/336/EEC (Electromagnetic Compatibility), as amended.
Environmental Protection
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
• Consult the dealer or an experienced radio/TV technician for help  Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.