Loading manuals...

Shark Navigator Lift-Away Upright Vacuum UV650 Manual


Shark Navigator Lift-Away Upright Vacuum UV650 Manual Image

IMPORTANT SAFETY INSTRUCTIONS

FOR HOUSEHOLD USE ONLY • PLEASE READ CAREFULLY BEFORE USE
If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. DO NOT force into outlet or try to modify to fit.

WARNING
To reduce the risk of fire, electric shock, injury, or property damage:

GENERAL WARNINGS
When using an electrical appliance,
basic precautions should always be
followed, including the following:

  1. Your vacuum cleaner may consist of
    a motorized nozzle, wand, hose, and/
    or vacuum pod. This device contains
    electrical connections, electrical wiring,
    and moving parts that potentially present
    risk to the user.
  2. Use only identical replacement parts.
  3. Carefully observe and follow the
    instructions provided below to avoid
    improper use of the appliance. DO NOT
    use the vacuum for any purpose other than
    those described in this manual.
  4. Before use, carefully inspect all parts
    for any damage. DO NOT use if any parts
    are damaged.
  5. The use of an extension cord is
    NOT recommended.
  6. This vacuum cleaner contains
    no serviceable parts.
    USE WARNINGS
  7. This appliance can be used by persons
    with reduced physical, sensory or mental
    capabilities or lack of experience and
    knowledge if they have been given
    supervision or instruction concerning
    use of the appliance in a safe way and
    understand the hazards involved. Cleaning
    and user maintenance shall not be made by
    children. Keep the appliance and its cord
    out of reach of children. DO NOT allow the
    appliance to be used by children. DO NOT
    allow to be used as a toy. Close supervision
    is necessary when used near children.
  8. Always turn off the vacuum cleaner
    before connecting or disconnecting any
    motorized nozzles or other accessories.
  9. DO NOT handle plug or vacuum cleaner
    with wet hands.
  10. DO NOT use without filters in place.
  11. Only use Shark® branded filters
    and accessories. Failure to do so
    will also void the warranty.
  12. DO NOT damage the power cord:
    a) DO NOT pull or carry vacuum cleaner
    by the cord or use the cord as a handle.
    b) DO NOT unplug by pulling
    on cord. Grasp the plug, not
    the cord.
    c) DO NOT run the vacuum cleaner over
    the power cord, close a door on the
    cord, pull the cord around sharp
    corners, or leave the cord near heated
    surfaces.
  13. DO NOT put any objects into nozzle or
    accessory openings. DO NOT use with any
    opening blocked; keep free of dust, lint,
    hair, and anything that may reduce airflow.
  14. DO NOT use if nozzle or accessory
    airflow is restricted. If the air paths or
    the motorized floor nozzle become
    blocked, turn the vacuum cleaner off and
    unplug from electrical outlet. Remove all
    obstructions before you plug in and turn
    on the unit again.
  15. Keep nozzle and all vacuum openings
    away from hair, face, fingers, uncovered
    feet, or loose clothing.
  16. DO NOT use if vacuum cleaner is
    not working as it should, or has been
    dropped, damaged, left outdoors, or
    dropped into water.
  17. Use extra care when cleaning
    on stairs.
  18. DO NOT leave the vacuum cleaner
    unattended while plugged in.
  19. When powered on, keep the vacuum
    cleaner moving over the carpet surface
    at all times to avoid damaging the
    carpet fibers.
    WARNING
  20. DO NOT place vacuum cleaner
    on unstable surfaces such as chairs
    or tables.
  21. Your Shark® Vacuum may not be designed
    to stand up on its own. When taking a
    break from cleaning, you may need to
    lean it against furniture or a wall, or lay it
    flat on the floor. Using the vacuum for an
    application where the unit lacks stability
    may result in personal injury.
  22. DO NOT use to pick up:
    a) Liquids
    b) Large objects
    c) Hard or sharp objects
    (glass, nails, screws, or coins)
    d) Large quantities of dust (drywall dust,
    fireplace ash, or embers). DO NOT use
    as an attachment to power tools for
    dust collection.
    e) Smoking or burning objects
    (hot coals, cigarette butts,
    or matches)
    f) Flammable or combustible materials
    (lighter fluid, gasoline,
    or kerosene)
    g) Toxic materials (chlorine bleach,
    ammonia, or drain cleaner)
  23. DO NOT use in the following areas:
    a) Poorly lit areas
    b) Wet or damp surfaces
    c) Outdoor areas
    d) Spaces that are enclosed and may
    contain explosive or toxic fumes or
    vapors (lighter fluid, gasoline, kerosene,
    paint, paint thinners, mothproofing
    substances, or flammable dust)
  24. Turn off all controls before plugging in
    or unplugging the vacuum.
  25. Unplug from electrical outlet
    when not in use and before
    any maintenance or cleaning.
  26. Hand wash with water only.
    Washing with cleaning chemicals could
    damage the unit.
  27. During cleaning or routine maintenance,
    DO NOT cut anything other than hair,
    fibers, or string wrapped around the
    brushroll.
  28. Allow all filters to air-dry completely
    before replacing in the vacuum to
    prevent liquid from being drawn
    into electric parts.
  29. Make sure the dust cup and all filters
    are in place after routine maintenance.
  30. If provided, secure the power
    cord around the two cord hooks
    during storage.

To reduce the risk of electric shock, this appliance has a polarized plug (one blade
is wider than the other). This plug will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. Do not change the plug in any way.
SAVE THESE INSTRUCTIONS

ASSEMBLY

  1. Place Pod onto Floor Nozzle Post.
  2. Insert Wand into pod.
  3. Attach bottom Accessory Holder onto pod.
  4. Insert Handle into wand.
  5. Attach Hose Clip to wand.
  6. Connect Hose to back of pod.

For proper operation, ensure all parts are firmly clicked into place.

WHOLE-HOME CLEANING

Select surface setting:
O Power Off
I Hard Floor For bare floors and area rugs.
II Carpet For high pile carpets

Suction Control offers variable suction based on your needs. Slide to MIN to reduce
suction and increase maneuverability on carpets. Slide to MAX to increase suction on bare floors.

BRUSHROLL INDICATOR LIGHT

WHAT DOES THE BRUSHROLL INDICATOR LIGHT MEAN?
Solid Green: The brushroll is spinning and working as it should.
Solid Red: There is a jam in the brushroll area. Turn your vacuum off and remove any blockages
in the nozzle.
Flashing Red: The motorized floor nozzle is overheating. Turn your vacuum off and wait a
minimum of 45 minutes for it to cool down.

NOTE: For deep carpet cleaning per ASTM F 608 (embedded dirt in carpets), setting II, Carpet. For deep carpet cleaning per ASTM F 608, set to MAX suction and Carpet.

CLEANING MODES

To engage brushroll, place foot on floor nozzle and tilt handle back.

Press the Handle Release button to detach the handle from the wand.

Press the Wand Release button to detach the wand from the pod.

Press the Lift-Away button to detach the pod from the floor nozzle.

With pod removed, press the Wand Release
button to detach the wand from the pod.

NOTE: All accessories are compatible with both the wand and the handle.

EMPTYING THE DUST CUP

IMPORTANT: Unplug the power cord before performing any maintenance

To remove Dust Cup, slide up release tabs on both sides of dust cup handle. Tilt dust cup
forward, then lift to remove.

Press lower release button to open bottom of dust cup.

To remove collected debris from Lint Screen, press top release button and lift handle to
open. Gently brush lint screen to clean.

To reinstall, place bottom of dust cup into pod and then tilt back until it clicks into place.

CLEANING THE FILTERS

CLEANING FILTERS

Regularly clean and replace the filters to keep your vacuum’s suction power optimal.
To clean filters, rinse with cold water only to prevent damage from cleaning chemicals. Allow all
filters to air-dry for at least 24 hours before reinstalling them to prevent liquid from being drawn
into electric parts.
CLEANING THE FILTERS
CLEANING FILTERS
IMPORTANT: DO NOT use soap when cleaning the filters.

CLEAN PRE-MOTOR FILTERS
EVERY 3 MONTHS
Remove Dust Cup, then lift out Filters.

CLEAN HEPA FILTER
EVERY YEAR
Press button at bottom of Filter Door. Tilt Filter Door and lift out. Remove HEPA Filter.
To reinstall, insert HEPA filter into unit and replace the filter door.

MAINTENANCE

Using a coin, turn locks counterclockwise to open, then lift off cover to access brushroll.

Squeeze tabs together and pull up to expose the airway.

Clear blockages from airway. Replace cover, pressing down firmly on all sides
before turning locks clockwise to close.

Use scissors to remove any string, carpet fibers, or hair that is wrapped
around the brushroll.

CHECKING FOR BLOCKAGES

Detach hose from vacuum pod, and check hose
and opening on back of pod for blockages

Detach wand from floor nozzle and handle, and check both ends for blockages

Detach wand from floor nozzle, tilt nozzle neck back, and check opening for blockages

Detach handle from wand and hose from the
vacuum pod, and check openings for blockages

Detach dust cup from vacuum pod. Empty dust cup, remove debris from lint screen, and check for
blockages.

AVAILABLE ACCESSORIES

A Duster Crevice Tool
Two cleaning tools in one. The crevice tool 
gives you extended cleaning reach for small
spaces, while the soft dusting brush cleans
a multitude of surfaces.

B Wide Upholstery Tool
The wide cleaning path helps remove pet
hair, dust, and large debris from mattresses,
couches, curtains, lampshades, and other
delicate upholstered surfaces.

C Hair Removal Multi-Tool
A single convertible tool for cleaning
tough pet messes two ways: Use the stiff
bristle brush to remove stubborn hair from
carpets, or take off the bristles to reveal
an upholstery tool perfect for cleaning
couches and bedding.

D Pet Power Brush
Designed to remove pet hair and ground-in
dirt from carpeted stairs and upholstery.

E Under-Appliance Wand
Clean under and behind hard-to-move
appliances and furniture with this adjustable
36” tool. Flip the extension piece over to
clean the underside of appliances

TROUBLESHOOTING

Vacuum is not picking up debris. No suction or light suction.

  • Check filters to see if they need cleaning. Follow instructions for rinsing and air-drying the
    filters before reinserting in the vacuum.
  • Dust cup may be full; empty dust cup.
  • Check hose, hose connections, nozzle, wand, pod, and accessories for blockages. Clear any
    blockages found.

(Refer to Checking for Blockages section for more information.)
Vacuum lifts area rugs.

  • Make sure Power/Surface switch is set to Hard Floor (setting I).
  • Suction is powerful. Take care when vacuuming area rugs or rugs with delicately sewn edges.
  • To minimize suction, slide the suction control valve to MIN.

Brushroll does not spin.

  • If the Brushroll Indicator Light turns red, immediately turn off and unplug the vacuum.
    Remove pod from floor nozzle and clear any blockages. Reconnect nozzle, plug in vacuum,
    and turn on power.
  • Set the Power/Surface switch to position II, Carpet.
  • Step on the floor nozzle and recline the handle to activate the brushroll.
  • If brushroll repeatedly stops spinning on plush or high-pile carpet, slide suction control
    to MIN.

Vacuum turns off on its own or indicator light flashes red.
This vacuum is equipped with a motor-protective thermostat. If your vacuum overheats, the
thermostat will automatically turn the suction motor off. Perform the following steps to restart
the thermostat:

  1. Turn vacuum off and unplug it.
  2. Empty dust cup and clean filters (see Emptying the Dust Cup and Cleaning the Filters).
  3. Check for blockages in hose, accessories, and inlet openings.
  4. Allow unit to cool for a minimum of 45 minutes.
  5. Plug in vacuum and turn it on.

NOTE: Not all accessories come with all units. Please see the enclosed Quick Start Guide for your unit’s configuration. To order additional accessories, visit sharkaccessories.com.

FIVE (5) YEAR LIMITED WARRANTY

The Five (5) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja
Operating LLC. Warranty coverage applies to the original owner and to the original product only and is
not transferable.
SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period
of five (5) years from the date of purchase when it is used under normal household conditions and
maintained according to the requirements outlined in the Owner’s Guide, subject to the following
conditions and exclusions:

What is covered by this warranty?

  1. The original unit and/or non-wearable components deemed defective, in SharkNinja’s sole discretion,
    will be repaired or replaced up to five (5) years from the original purchase date.
  2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following the
    receipt date of the replacement unit or the remainder of the existing warranty, whichever is later.
    SharkNinja reserves the right to replace the unit with one of equal or greater value.

What is not covered by this warranty?

  1. Normal wear and tear of wearable parts (such as foam filters, HEPA filters, pads, etc.), which require
    regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered
    by this warranty. Replacement parts are available for purchase at sharkaccessories.com.
  2. Any unit that has been tampered with or used for commercial purposes.
  3. Damage caused by misuse (e.g., vacuuming up water or other liquids), abuse, negligent handling,
    failure to perform required maintenance (e.g., not cleaning the filters), or damage due to mishandling
    in transit.
  4. Consequential and incidental damages.
  5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused
    in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the
    repair is performed by a repair person not authorized by SharkNinja.
  6. Products purchased, used, or operated outside North America.

How to get service
If your appliance fails to operate properly while in use under normal household conditions within the warranty period, visit sharkclean.com/support for product care and maintenance self-help. Our Customer Service Specialists are also available at 1-800-798-7398 to assist with product support and warranty service options, including the possibility of upgrading to our VIP warranty service options for select product categories. So we may better assist you, please register your product online at registeryourshark.com and have the product on hand when you call.
SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of $24.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.
How to initiate a warranty claim
You must call 1-800-798-7398 to initiate a warranty claim. You will need the receipt as proof of purchase. We also ask that you register your product online at registeryourshark.com and have the product on hand when you call, so we may better assist you. A Customer Service Specialist will provide you with return and packing instruction information.
How state law applies
This warranty gives you specific legal rights, and you also may have other rights that vary from state to state. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

REGISTER YOUR PURCHASE

registeryourshark.com

Scan QR code using
mobile device

RECORD THIS INFORMATION
Model Number: ______________________________
Serial Number: _______________________________
Date of Purchase: _____________________________
(Keep receipt)
Store of Purchase: ____________________________

TECHNICAL SPECIFICATIONS
Voltage:                         120V, 60Hz
Watts:                            800W
Amps:                           6.7A

Benefits of registering your product and
creating an account:
• Get easier, faster product support and
access to warranty information
• Access troubleshooting and product care
instructions
• Be among the first to know about
exclusive product promotions

TIP: You can find the model and serial numbers on the QR code label on the
bottom of the back of the vacuum pod.

PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.
This Owner’s Guide is designed to help you get a complete understanding of your new
Shark Navigator® Lift-Away®.
SharkNinja Operating LLC
US: Needham, MA 02494
1-800-798-7398
sharkclean.com
Illustrations may differ from actual product. We are constantly striving to improve our products;
therefore the specifications contained herein are subject to change without notice.
For SharkNinja U.S. Patent information, visit sharkninja-uspatents

© 2019 SharkNinja Operating LLC. LIFT-AWAY, SHARK, and SHARK NAVIGATOR
are registered trademarks of SharkNinja Operating LLC. NAVIGATOR is a
trademark of SharkNinja Operating LLC.
UV650_IB_MP_Mv3
PRINTED IN CHINA



More Manuals From Shark