TOMMY EARBUDS 333
AIR SPORT
NOISE-CANCELING WIRELESS EARBUDS
Bluetooth
USER MANUAL
HILFIGER EP333 Noise Cancelling Wireless Earbuds
Multifunction button:
Power on/off
Charge Directions and Use:
- Fully charge the earphones before using them for the first time.
- Plug the USB charging cable Into the controller of the headphones.
- The LED light will turn blue when the earphones are fully charged.
Attention: Please use the original Included charging cable to connect the earphones to your computer or compatible USB charging device.
Basic Use:
 |
Power on: Press & hold the multi-function button until the blue LED goes on. Power off: Press & hold the power button until the red LED goes on |
 |
Pairing: When the unit is powered off, press & hold the multi-function button for about 10-15 sec until blue & red LED lights begin to blink. The unit is now in pairing mode. Make sure your Bluetooth-enabled device is discoverable. In Available Devices choose “TOMMYEARBUDS 333” and select ‘Pair. |
 |
Volume control: While listening, press the V+ button to increase volume, or the V- button to decrease volume. |
 |
Music track: While listening, press & hold the V+ button for the next song, and press & hold the V- button for the previous song. |
 |
Pause/Play: While listening, press the multi-function button to pause music. Press the button again to play music. |
 |
Answer/End call: Tap the multi-function button. Reject call: Press the multi-function button for 2-3 seconds. |
LED Indicator:
Low battery warning:
Red LED flashing.
Charging:
Red LED on when charging and blue LED on when fully charged. }
Bluetooth connected:
Blue LED flashing slowly.
Power on/off:
When turning the earphones on the LED light will blink blue. When turned off the LED will turn red.
Bluetooth pairing:
Blue and red LED flashing rapidly together.
Pairing The Bluetooth Earphones:
Pairing the device Is quite simple. Put the earbuds and compatible Bluetooth device close to each other (no more than 3 feet apart). When powering on the SWS EtECNONICS earbuds press and HOLD down the center power button on the controller. The voice prompt will say “Ready to pair”
***DO NOT release the power button for another 10-15 sea and the LED indicator lights should begin to blink red and blue. Your device is now in pairing mode.
From here you’ll have to navigate through Bluetooth Settings on your mobile device and choose “SVESEP333” from the list of all available Bluetooth devices within range. This should begin the pairing sequence.
After pakhg Is successfully completed, you ‘Mil hear a tone in the earphones indicating that the connection has been established and the voice prompt will state “Your Device Is Now Paired.’
Now you can use your Tommy Earbuds 333 to listen to music and make phone calls.
SPECIFICATION
| Bluetooth Profiles Operation Range Frequency Range Lithium-Ion Battery I, Charging Voltage Charging Time Playing Music Time Talk Time Standby Time |
HSP, HFP, A2DP, AVRCP 33 Ft/360o 20Hz-20,000Hz 3.7V/60mAh DC4.75-5.25V About 2 Hours Up to 5 Hours Up to 5 Hours Up to 200 Hours |
Warnings and Notes:
- Do not store the unit in a high-temperature environment, including intense sunlight or heat. Do not place the unit near fire or other excessively hot environments.
- Be cautious of excessive drops, bumps, abrasions, or other types of impact. If there is any damage to the battery such as dents, punctures, tears, or deformities of corrosion, due to any cause, discontinue use and contact the manufacturer or dispose of it in an appropriate manner.
- Do not disassemble or attempt to modify or replace any part of this unit.
- Do not expose the unit to moisture, or snow, or submerge it in liquid.
- Do not use units in the vicinity of flammable fumes or gases (such as propane tanks or large engines).
- Do not attempt to operate the unit using any other method than directed.
TECHNICAL SUPPORT:
Please do not attempt to fix the product by yourself. If you are experiencing any problems with the product please do not return it to the store you bought it from. You can contact our technical support representatives and they will assist you with any questions you might have.
Questions? Visit our support page online at www.sveselectronics.com
WARRANTY REGISTRATION
To register your SVES Electronics product please visit www.sveselectronics.com
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– – Reorient or relocate the receiving antenna.
– – Increase the separation between the equipment and receiver.
– – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– – Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirements.
