Loading manuals...

Tribit BTS20C XSound Go Bluetooth Speaker Manual

Tribit BTS20C XSound Go Bluetooth Speaker Manual Image

Safety instructions

• Avoid dropping.
• Do not disassemble.
• Avoid extreme temperatures.
• Do not use the device outdoors during thunderstorms.
• Do not use any corrosive cleaner/oil to clean.


Bluetooth version: V5.0
Support: A2DP, AVRCP, HFP, HSP
Output power: 2 x 8W
Battery: 3.7V, 4400mAh
Battery charge time: 5 hour
Input: DC5V/1A
Dimension: 175 x 59 x 56 (mm)
Weight: 380g

Tribit BTS20C XSound Go Bluetooth Speaker - in the box Tribit BTS20C XSound Go Bluetooth Speaker - over viou
Tribit BTS20C XSound Go Bluetooth Speaker - Connections Tribit BTS20C XSound Go Bluetooth Speaker - Bluetooth

Stereo Mode

  1. Make sure both speakers are on.Tribit BTS20C XSound Go Bluetooth Speaker - stereo mode
  2. PressTribit BTS20C XSound Go Bluetooth Speaker - Bluetooth 1on one of the speakers to enter the pairing state.
  3. PressTribit BTS20C XSound Go Bluetooth Speaker - Bluetooth 1on the other speaker for 5s, then release the button to enter Stereo pairing when you hear the “Stereo mode”. When you hear “Left channel” on the left speaker and “Right channel” on the right speaker, the “Stereo mode” is on.


Buttons Operation & Function
Power on/off Press to turn on/off
Bluetooth Pre. to enter pairing mode
Volume + Press to incr.se the volume level
Volume – Press to decrease the volume level
play/pause • Press to play/pause music and answer/end call
• Long press to reject a call
• Press twice to skip to the next track
• Press triple to skip to the previous track


Indicator Status
Blue indicator flashes slowly Reconnection mode
Blue indicator flashes quickly Bluetooth pairing mode
Blue indicator keeps on The pairing has been successful
Red indicator flashes slowly Low battery power (<15%), charge the speaker as required
Red indicator flash. quickly Low battery power (<2%) and will automatically power off after 5s charge the speaker immediately

Reset If this speaker has some problem, you can try to press and hold the “Volume +” and “Volume —” buttons simultaneously for 5 seconds to reset, and then pair again (delete the old pairing in your device).
FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.lf this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF warning for Mobile devices:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Customer service
18-month limited warranty
• For FAQS and more information, please
• Email to: [email protected]

More Manuals From Tribit