WISeNeT In-ceiling Housing SHP-1680F Manual

Wisenet In-Ceiling Housing Installation Manual

SHP-1680F

Overview

This In-CEILING HOUSING is a mounting ADAPTOR that is designed to mount the smart dome camera in built-in style on a double-layer ceiling.

What’s Included

Installation Instructions

1. Select an installation position or place that can endure more than 4 times of the total weight of the installation structure.
2. At least 250mm or more of spare height is required above the CEILING BOARD.
3. CEILING BOARD’s thickness should be less than 40mm.
4. Be sure to secure the SAFETY WIRE to avoid a product fall.
5. If you want to attach the camera to the ADAPTOR, use the only provided SCREWS.

How to install (XNP-6120/HCP-6120 SERIES)

1. Place the TEMPLATE on the CEILING BOARD and drill a guided hole.
   ❶ Remove the round filling (“C”) from the TEMPLATE.
   ➋ Place TEMPLATE A onto the CEILING BOARD to which you will attach the ceiling mount ADAPTOR and drill a hole of Ø213mm in diameter.
   See the figure below for the hole shape.
   
2. Fix the ANCHOR BOLT onto the concrete CEILING, and secure the SAFETY WIRE to the ANCHOR BOLT as below:
   ❶ Tighten the nut (“N1”) on the ANCHOR BOLT.
   ➋ Insert the provided SAFETY BRACKET into the ANCHOR BOLT.
   ➌ Tighten two nuts (“N2”,”N3”) onto the ANCHOR BOLT.
   ➍ Hook and fix one end of the SAFETY WIRE onto the SAFETY BRACKET.
   ➎ Hook and fix the other end of SAFETY WIRE onto the HOUSING as shown below.
   
3. To connect to the camera, insert the external cable through the side hole on the housing to the inside of the housing as shown in the figure.
   
4. Push the HOUSING inside the CEILING through the CEILING hole, and tighten the SCREWs (x2) clockwise to fix the HOUSING on the CEILING.
   (The BRACKET will be positioned from <A> to <B> as shown.)
   
5. Remove the dome cover after loosening the three bolts by turning them counterclockwise using an L wrench.
   
6. Remove the safety wire that is connected to the dome cover and camera body, and connect it inside of the dome cover as shown in the picture.
   
7. Connect the required cable to the terminal on the camera. Please refer to the installation guide for details on camera installation.
   
8. Connect the camera to the bracket placed in the housing using the screws (3 EA).
   
9. Attach the COVER to the HOUSING.
   

How to install (XNV-6120 SERIES/XNV-6085 SERIES)

1. Place the TEMPLATE on the CEILING BOARD and drill a guided hole.
   ❶ Remove the round filling (“C”) from the TEMPLATE.
   ➋ Place the TEMPLATE A onto the CEILING BOARD to which you will attach the CEILING mount ADAPTOR and drill a Ø213mm hole.
   See the figure below for the hole shape.
   
2. Insert the lower bracket into the housing and turn it in the [LOCK] direction to fix it.
   
3. Fix the ANCHOR BOLT onto the concrete CEILING, and secure the SAFETY WIRE to the ANCHOR BOLT as below:
   ❶ Tighten the NUT (“N1”) on the ANCHOR BOLT.
   ➋ Insert the provided SAFETY BRACKET into the ANCHOR BOLT.
   ➌ Tighten two NUTs (“N2”,”N3”) onto the ANCHOR BOLT.
   ➍ Hook and fix one end of the SAFETY WIRE onto the SAFETY BRACKET.
   ➎ Hook and fix the other end of SAFETY WIRE onto the HOUSING as shown below:
   
4. To connect to the camera, insert the external cable through the side hole on the housing to the inside of the housing as shown in the figure.
   
5. Push the HOUSING inside the CEILING through the CEILING hole, and tighten the SCREWs (x2) clockwise to fix the HOUSING on the CEILING.
   (The BRACKET will be positioned from <A> to <B> as shown.)
   
6. As shown in the figure, pull out the protrusions of the rubber cap in the bottom to make a small hole and remove the cable through it to connect to the external cable.
   
7. Connect the camera to the bracket placed in the housing using the screws (3 EA).
   
8. Attach the COVER to the HOUSING.
   

How to install (XND-6085/XND-6085V SERIES)

1. Place the TEMPLATE on the CEILING BOARD and drill a guided hole.
   ❶ Remove the round filling (“C”) from the TEMPLATE.
   ➋ Place the TEMPLATE A onto the CEILING BOARD to which you will attach the CEILING mount ADAPTOR and drill a Ø213mm hole.
   See the figure below for the hole shape.
   
2. Insert the lower bracket into the housing and turn it in the [LOCK] direction to fix it.
   
3. Fix the ANCHOR BOLT onto the concrete CEILING, and secure the SAFETY WIRE to the ANCHOR BOLT as below:
   ❶ Tighten the NUT (“N1”) on the ANCHOR BOLT.
   ➋ Insert the provided SAFETY BRACKET into the ANCHOR BOLT.
   ➌ Tighten two NUTs (“N2”,”N3”) onto the ANCHOR BOLT.
   ➍ Hook and fix one end of the SAFETY WIRE onto the SAFETY BRACKET.
   ➎ Hook and fix the other end of SAFETY WIRE onto the HOUSING as shown below:
   
4. To connect to the camera, insert the external cable through the side hole on the housing to the inside of the housing as shown in the figure.
   
5. Push the HOUSING inside the CEILING through the CEILING hole, and tighten the SCREWs (x2) clockwise to fix the HOUSING on the CEILING.
   (The BRACKET will be positioned from <A> to <B> as shown.)
   
6. Connect the camera to the bracket placed in the housing using the screws (3 EA).
   
7. Attach the COVER to the HOUSING.
   

Product Specifications

Unit: mm (Inches)

Head Office
6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si,
Gyeonggi-do, 463-400 Rep. of KOREA
Tel : +82.70.7147.8753 Fax : +82.31.8018.3740
www.hanwha-security.com

Hanwha Techwin America
500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666
Toll Free +1.877.213.1222 Direct +1.201.325.6920
Fax +1.201.373.0124
www.hanwha-security.com

Hanwha Techwin Europe
Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom
Tel +44.1932.57.8100 Fax +44.1932.57.8101
www.hanwha-security.eu