7.2V Cordless Grass Shear & Hedge Trimmer
Instruction Manual
WARNING: READ THIS MANUAL BEFORE USING
For your safety and for proper operation and maintenance, please read carefully and keep it readily available for future reference.
IMPORTANT TIPS:
- The unit is fully assembled. Remove clear plastic blade guard before use and save it to use as blade cover when the unit is not in use.
- The battery must be charged before use. Please refer to the battery charging instructions.
- If the blade becomes jammed on a branch while cutting, IMMEDIATELY release trigger and clear jam. If you continue to hold the trigger with the blade jammed you will damage the motor.
- IMPORTANT: This is a powerful tool that is remarkably easy and comfortable to use. As such, please pay attention to the placement of the blades while using to avoid cutting yourself.
TECNICHAL SPECIFICATIONS
| Type | ET1511 |
| Battery voltage | DC 7.2V |
| Battery type | Li-Ion |
| No load speed | 1100rpm |
| Cutting length | 170mm |
| Cutting width | 93mm |
| Battery capacity | 1.5Ah |
| Charging time | 4Hours |
SAFETY INSTRUCTIONS
Please read these instructions before operating this product and save these instructions. For safe operation:
- Keep children and animals away from the working area.
- Switch on the motor only when the hands and feet are away from the cutting blades.
- Use only the manufacturer-recommended replacement parts and accessories.
- When not in use, tools and batteries should be stored separately in a dry, high, or locked-up place, out of reach of children. Ensure that the battery terminal cannot be short-circuited by other metal parts such as screws, nails, etc.
- Do not use excessive pressure during operation. It will do the job better and safer at the rate for which it was intended.
- Dress properly
Do not wear loose clothing or jewelry; they can be caught in moving parts.
Wear stout shoes while using the grass shear. Wear protective hair covering to contain long hair. - Maintain tools with care
Keep cutting tools sharp and clean for better and safer performance. Follow instructions for lubrication and changing accessories. - Disconnect tools
Disconnect the tool from its battery pack when not in use, before servicing and when changing accessories such as blades. - Avoid unintentional starting
Do not carry the tool with a finger on the switch. - Stay alert
Watch what you are doing. Use common sense. Do not operate the tool when you are tired. - Warning
The use of any accessory or attachment, other than recommended in this instruction manual, may present a risk of personal injury.
Ensure that the battery pack is correct for the tool.
Ensure that the outside surface of the battery pack or tool is clean and dry before plugging it into the charger.
Ensure that batteries are charged using the correct charger recommended by the manufacturer. Incorrect use may result in a risk of electric shock, overheating, or leakage of corrosive liquid from the battery. - Have your tool repaired by a qualified person
This tool is constructed in accordance with the relevant safety requirements. Qualified persons using original spare parts should only carry out repairs; otherwise, this may result in considerable danger to the user. - Disposal of battery
Ensure battery is disposed of safely as instructed by the manufacturer.
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER
- Before using the charger, read all instructions and cautionary markings on the charger, battery pack, and product using the battery pack.
- DANGER: 230 volts present at charging terminals. Do not probe with conductive objects. Danger of electric shock or electrocution.
- The charger and battery are specifically designed to work together. DO NOT attempt to charge the battery with any chargers other than the ones in this manual.
- Do not expose the charger to rain or snow.
- This charger is not intended for any use other than charging rechargeable batteries. Any other uses may result in a risk of fire, electric shock, or electrocution.
- To reduce the risk of damage to the electric plug and cord, disconnect from the mains socket by pulling the plug rather than the cord.
- Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
- The charger is ventilated through slots in the top and the bottom of the housing. Do not place any object on top of the charger or on a surface that might block the ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source.
- Do not operate the charger if it has received a sharp blow, been dropped, or otherwise damaged in any way.
- Do not disassemble the charger. Take it to an authorized service center when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
- To reduce the risk of electric shock, unplug the charger from the outlet before attempting any cleaning. Removing the battery pack will not reduce this risk.
- Never attempt to connect 2 chargers together.
- DO NOT store or use the tool in locations where the temperature may reach or exceed 105°F (such as outside sheds or metal buildings in summer).
- The charger is designed to operate on standard household electrical power (230volts). Do not attempt to use it on any other voltage!
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY
The battery is not fully charged when you first receive it. First, read the safety instructions below the follow charging notes and procedures.
READ ALL INSTRUCTIONS CAREFULLY AND KEEP THEM IN A SAFE PLACE FOR FUTURE REFERENCE.
- Do not incinerate the battery even if it is severely damaged or is completely worn out. The battery can explode in a fire.
- A small leakage of liquid from the battery cells may occur under extreme usage or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If battery liquid gets in your eyes, flush them with clean water for a minimum of minutes and seek immediate medical attention.(medical notes: the liquid is 25-35% solution of potassium hydroxide.) - Do not connect the positive pole and the negative pole of the battery with any metal objects. The battery could be short-circuited causing damage to the battery and possibly causing severe burns or fire.
- Charge the battery only in the chargers supplied with the product.
- NOTE: the battery in your tool is the lithium-ion type, with no self-discharge or memory effect. Insert/remove the battery pack
- Always release the On/Off switch before insertion or removal of the battery pack.
- To remove the battery pack, withdraw it from the tool while pressing the spring buttons 5 on
both sides of the cartridge.
Attention: The moving blade will move back if the moving blade is not in the fully open position
when inserting the battery pack.
OPERATING YOUR TOOLS
Warning: Never remove or bridge the switching devices.
The starting lockout prevents your tools from being switched on unintentionally.
Cutting without swivel handle:
1. Push the lock-off button (1) forward and press switch (2).
2. Release the lock-off button (1) again.
The function of the swivel head
Hold the handle 2 tightly. Slide the lock button 1 up and then turn the cutter head 3 to the desired position.Release the lock button 1 again and check whether the cutter head is locked in place.
Note:The cutter head can be locked in four positions(-90°、0°、90°、)。
● Battery charging
Do not use other battery chargers. The supplied battery charger is designed for The lithium-ion battery in your machine.
Observe correct mains voltage: The voltage of the power source must agree with the voltage specified on the nameplate of the unit. Equipment marked with 230 V can also be connected to 220 V or 240 V.
The Li-ion battery is protected against deep discharging by the “Electronic Cell Protection”. When the battery is empty, the machine is switched off by means of a protective circuit: The inserted tool no longer rotates.
WARNING: Do not continue to press the On/Off switch after the machine has been automatically switched off. The battery can be damaged.
The battery is supplied partially charged. To ensure the full capacity of the battery, completely charge the battery in the battery charger before using your power tool for the first time.
A battery that is new or has not been used for a longer period does not develop its full capacity until after approx. 5 charging/discharging cycles.
When the machine can not rotate while the On/Off switch is pressed, then the battery has no enough capacity and should be charged.
Plug the mains plug7 of the charger 6 into socket 8 of the battery pack 5. And then Insert the charger into the power supply. At this time, the battery charge control indicator 9 lights up. The battery charge-control indicator indicates the charging progress. The indicator lights up red during the charge procedure. The battery is completely charged when the indicator lights up green again.
Disconnect the battery charger from the mains supply when not using it for longer periods.
LIGHT BUTTON INSTRUCTION
Press the button （ 1 ）, when the battery pack is full of charge, the red light（LG）、yellow light（LY）and green light （LG）on; and when the battery pack comes to be low power, the red light and yellow light on; when the battery is no power, only red light on.
CHANGE THE BLADES
Warning!
DO NOT operate the switch before dismantling or fitting the blades. Risk of injury!
The blade can be changed rapidly and expediently without any tools.
Follow the steps as shown in the upper figure.
1 About the button press enter
2 The blade take-up
Take off the blades and install another blade.
① Blade according to the graphical position inclined outfit, put the blade part (A) into the body
② The blade according to the graphic cover
Warning!
DO NOT operate the switch before the blade cover is installed. Risk of injury!
MAINTENANCE AND REPAIR
Do not rinse the machine with water.
The cutter should be stored in a dry place when it is not in use.
Before every use of this cutter, check whether the blade is in good order and it must be repaired in time if damage has been found.
The blade should be cleaned and lubricated in time after every use of the cutter. When the cutter is to be used for a long time the blades should be lubricated during operations intervals.
