THOMSON ROC1128SAM Replacement Remote Control Manual

Replacement Remote Control
ROC1128SAM
Instruction ManualCompatible with most Samsung TVs

Dimensions
=212 x51x25mm
86 g

Replacement Remote for
SAMSUNG SERIES: TV/LCD/LED/HDTV

Thank you for your decision for Thomson product. Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference. This remote control can by default control 90%models of the SAMSUNG brand, there´s no need to set it up. lf the remote doesn‘t work, please choose one of the setup methods described in chapter 5.

The keys

1. Input signal source 2. POWER TV ON /OFF Indicator LED 3. Switch to signal source PC 4. Switch to signal source TV 5. Switch to signal source HDMI 6. Numeric keys 0–9toenter channel numbers 7. Previous channel 8. Access to 2- or 3- digit channel numbers 9. Media Player 10. Show the Electronic Program Guide (if supported by the TV) 11. Program MENU 12. TV Mute 13. Channel up/down 14. Teletext ON /OFF /MIX 15. Streaming app menu 16. Change your TV‘s volume 17. TOOLS MENU

18. On-Screen Info 19. Use when watching TV to see what‘s on other channels or to highlight/Select On-Screen options 20. Return /Back key 21. Turn off the menu of the selected product. 22. Use to select a variety of on-screen options 23. Sound Mode 24. PictureMode 25. Multi Sound 26. Favorite Channel 27. PictureSize 28. 3D Mode ON/OFF 29. Suspends play and stops on an image (DVD, BlueRay…) 30. Fast Forward(DVD, BlueRay … ) 31. Goes backward(DVD, BlueRay … ) 32. Stop the disc (DVD, BlueRay … ) PIP (PictureinPicture) 33. Play adisc (DVD, BlueRay … ) PIP Position 34. Record  SWAP PIP

 Explanation of the Note and Warning symbol

Warning
This symbol is used to indicate safety instructions or to draw your attention to specifichazards and risks.
Note
This symbol is used to indicate additional information or important notes.

Package Contents

• Replacement Remote Control
• 2xAAA Batteries
• These operating instructions incl. Code List

Safety notes

• Do not use the Universal Remote Control in moist or wet environments and avoid spray water contact.
• Do not expose the Universal Remote Control to heat sources or direct sunlight.
• Do not drop the Universal Remote Control.
• Never open the Universal Remote Control. It contains no user-serviceable parts.
• As with all electrical devices, keep the Universal Remote Control away from children.

Warning

• When inserting batteries, note the correct polarity (+ and -markings) and insert the batteries accordingly. Failure to do so could result in the batteries leaking or exploding.
• Do not short-circuit batteries.
• Do not charge batteries.
• Do not throw batteries in a fire.
• Keep batteries out of the reach of children.
• Do not allow children to change batteries without supervision.
• Remove the batteries from products that aren’t being used for an extended period.

Getting started –Installing the Batteries

Note

• Use 2AAA batteries
• Remove the battery cover from the bottom of the remote.
• Check the +/- polarity on the batteries and inside the compartment.
• Insert the batteries.
• Slide the battery holder back into the remote until the clips locate.

Note –
Note – Code Memory
Code Memory
This remote control saves the settings during battery change.

Setup

This remote control can by default control 90% of models of the SAMSUNG brand, there´s no need to set it up. lf it doesn‘t work, please choose one of the following setup methods 5.1 or 5.2.

INPUT CODE

CODE List:
001, 002, 003, 004, 005, 006, 007, 008, 009, 010, 011, 012, 013, 014, 015, 016, 017, 018, 019, 020, 021, 022, 023, 024, 025, 026, 027, 028, 029, 030, 031, 032, 033, 034, 035, 036, 037, 038, 039, 040, 041, 042, 043, 044, 045, 046, 047, 048, 049, 050, 051, 052, 053, 054, 055, 056, 057

1. Press and hold the key [MUTE] and [POWER] until the LED will be lit, then release keys.
2.  Enter the three codes from code Iist. When the code input is finished, the LED will turn off.
3.  Please try to use the remote control. lf it doesn‘t work well, please try other codes: [002], [003], [004] …

Note
lf the code is invalid, the LED flashes twice  and then lights up permanently.Toexit the setup, please press [MUTE].

FAST SEARCH

1. Press and hold the key [MUTE] and [POWER] until the LED will be lit, then release keys.
2.  Press the key [CH+]. Each time you press, the remote will search once. When the code changes, you can test if [POWER], [VOL+],[MENU],[0-9] keys work well. If ok , please press [MUTE] to save the code and exit.
3. lf it doesn‘t work well, repeat the fast search by pressing [CH+].

CODE INQUIRY

Use the following method to find out which code is currently set:

1. Press and hold [MUTE], then press [POWER] until the LED will be lit, then release keys.
2. Input [9].[9].[0] with number keys. The LED will flash twice and goes off.
3. Press the number key 1for the 1st digit of the code. The LED will start to flash. Count the LED flashes. The number of flashes resembles the code‘s first digit. Repeat this procedure for the 2nd and 3rddigit of the code:
   2nd digit -> enter 2 ->count LED flashes
   3rddigit -> enter 3 ->count LED flashes
   lf code number is [0] the LED will not flash.

Compatible Remote Control Model

Due to too many Remote Control models, we only list some of them below.
If your remote control is similar to the drawing, the replacement remote can control your TV (Page 74).

Resetting to factory settings

Press and hold the [RETURN] and [0] buttons for about 5seconds until the status LED flashes three times and then goes out. The remote control is now successfully reset to the factory settings.
Note
All keys with learned codes or all copied keys, as well as all remote control settings will be deleted.

LEARN MODE

This remote control is equipped with a learning function. Thus, you could learn the functions of your original remote to this remote control.

BEFORE STARTING TO LEARN MODE

• The batteries in the two remote controls have to be in good condition. Replace them if necessary.
• Place the remote controls with the infrared diodes so that they point towards each other.
• Where necessary adjust the height of both remotes so that infrared diodes are properly aligned.
• The distance between the remote controls should be about 3cm.

Note

• Do not move the remote controls during the learning procedure.
• Ensure that the room is not lit by fluorescent tubes or low energy consumption lamps since such light sources could interferewith the copying.
• The 2remotecontrols must be at least 1meter away from any light source.
• During learning mode, if no key is selected for more than 15 seconds, the learning mode will exit automatically or if no other remote signal is received.
• Each function key will hold only one command. The new command to be learned will automatically replace the previous one.

ENTER LEARN MODE

1. Press and hold the [MUTE] and [VOL+] keys for approx. 5seconds until the LED will be lit.
2. Enter the code [9] [8] [0], the LED will flash 2times and then remain on.
3. The remote control is now ready to learn new commands.

LEARNING OF KEYS

1. Press and release the desired key on the original remote control which you want the command to be learned. The LED at your replacement remote will flash to confirm that the information has been received.
2. Then press and release the target key on the remote control you want to be learned.
3. If the LED flashes 3times and then remains on, the command has been learned successfully.
4. Repeat these steps to learn other key functions.
5. Press the [MUTE] and [VOL-] buttons to save all learned functions and to exit the learning mode.

Note
While replacing the batteries, the remote control will keep the functions of the learned keys.

CLEARING OF LEARNED KEYS

6.4.1 CLEARING OF ONE LEARNED KEY 

1. Press and hold [MUTE] and [VOL+] keys for 5seconds until the LED will be lit.
2. Enter the code [9] [8] [1], the LED will flash 2times and then remain on.
3. Press and release the desired key at the replacement remote control which you want to clear the learned command. If the LED flashes 3times, the learned command has been cleared successfully.

6.4.2 CLEARING OF ALL LEARNED KEYS

1. Press and hold [MUTE] and [VOL+] keys for 5seconds until the LED will be lit.
2. Enter the code [9] [8] [2], the LED will flash 2times and then remain on.
3. Press and release the [OK] key at the replacement remote control. If the LED flashes 3times, all commands have been cleared successfully.

SIMPLE Mode

This remote control is equipped with an SIMPLE Mode. Thus you could reduce the functionality of the remote control to its basic functions. It avoids that the TV Settings are changed by mistake. During the SIMPLE Mode, you still could use the following keys:

	POWER TV ON /OFF
VOL	Change your TV‘s volume
	TV Mute
CH	Channel up/down
0-9	Numeric keys 0–9toenter channel numbers
TTX/MIX	Teletext ON /OFF /MIX
	Use to select a variety of on-screen options
GUIDE	Show the Electronic Program Guide (if supported by the TV)
	Input signal source /Indicator LED
	Turn off the menu of the selected product
TV	Switch to signal source TV

Enter SIMPLE Mode

1. Press and hold [MUTE] and [VOL+] keys for 5seconds until the LED will be lit.
2. Enter the code [9] [7] [0], the LED will flash two times and then remain on.
3. Press and release the [OK] key,if LED flash 3times, you have entered the SIMPLE Mode successfully

Exit SIMPLE Mode

1. Press and hold [MUTE] and [VOL+] for 5seconds until the LED will be lit.
2. Enter the code [9] [7] [0], the LED will flash two times and then remain on.
3.  Press and release the [EXIT] key,if the LED flashes 3times, you have exited the SIMPLE Mode.

Note
While the SIMPLE Mode is activated only the keys mentioned in chapter 7. will work. If one of these keys is pressed the LED will be lit until the key is released. If one key is pressed during the normal mode, the LED will flash.

Maintenance

• Do not mix new and used batteries for powering the Universal Remote Control, as old batteries tend to leak and may cause power drain.
• Do not use corrosive or abrasive cleansers on your Universal Remote Control.
• Keep the Universal Remote Control dust-free by wiping it with a soft, dry cloth.

Troubleshooting

Q. My Universal Remote Control does not work at all!
A. Check your TV. If the TV main switch is turned off, your Remote cannot operate your TV.
A. Check whether your batteries are inserted properly and are in the correct +/- position.
A. If the batteries are low, replace the batteries.
Q. My TV responds only to some of the commands.
A. Try other codes until most keys work properly.
Q. Some keys of the Remote Control do not work anymore?
A. Maybe the SIMPLE Mode had been activated. Deactivate the SIMPLE Mode as explained in chapter 7.2.

Warranty Disclaimer

The manufacturer assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or failure to observe the operating instructions and/or safety notes.

Service and Support

Please contact Hama Product Consulting if you have any questions about this product.
Hotline: +49 9091 502-115 (German/English)
Further support information can be found here: www.hama.com

Recycling Information

Note on environmental protection:
After the implementation of the European Directive 2012/19/EU and 2006/66/EU in the national legal system, the following applies: Electric and electronic devices, as well as batteries, must not be disposed of with household waste.
Consumers are obliged by law to return electrical and electronic devices as well as batteries at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilizing old devices/Batteries, you are making an important contribution to protecting our environment.

83502
Thomson is a trademark of Technicolor or its affiliates used under license to HAMA GmbH &CoKGin86652 Monheim /Germany www.thomson-av-accessories.eu

ROC1128SAM
00132673