The Anker SoundCore can connect to smart devices using Bluetooth. If you need to pair it using that Bluetooth technology then you can learn how to do so in this digital instructions manual.
For FAQs and more information, please visit:
At a Glance
Using Your SoundCore
Turn on / off
Note: SoundCore will automatically turn off after 10 minutes if no device is connected.
Charge your SoundCore
Flashing red Low power
Steady red Charging
Off Fully charged
Use the included USB cable to charge your SoundCore and make sure it is fully charged before first use.
Pair with your device
Un-pair connected device and re-enter pairing mode
Rapidly flashing blue Pairing mode
Steady blue Connected to a device
When turned on, SoundCore will automatically connect to the last connected device if available. If not, SoundCore will enter pairing mode.
Having connection problems? Remove SoundCore from your device’s Bluetooth history, ensure it’s less than 3 feet away then try pairing again.
Connect via AUX
SoundLine AUX cable sold separately.
Rapidly flashing blue AUX mode
When using AUX mode, control audio playback via the connected device.
Play – pause
Volume up / down
Answer / End call
Put current call on hold and answer incoming call
- Input : 5 V = 1 A
- Audio output : 3 W × 2
- Charging time: 5 – 6 hours
- Play time (varies by volume level and content) : 24 hours
- Size : 165 × 45 × 54 mm 6.5 × 1.8 × 2.1 in
- Weight : 365 g / 12.9 oz
- Range : 20 m / 66 ft
Use original or certified cables
Don’t expose to liquids
Avoid extreme temperatures
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for help.
RF Warning Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction. Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados.
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Anker Technology Co., Limited is under license.
This product complies with the radio interference requirements of the European Community.
Declaration of Conformity
Hereby, Anker Technology Co., Limited declares that the radio equipment type A3102 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
4003-0329 (Capitais e regiões metropolitanas) ou 0800 729 0329 (Demais localidades).
BT Maximum output power: 1.5dBm
BT Frequency band: 2.4G band (2.4000GHz-2.4835GHz)
IC NOTICE TO CANADIAN USERS
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. This Class B digital apparatus complies with Canadian ICES-003 (Cet appareil numérique de la Classe B conforme à la norme NMB-003 du Canada).
1. 18-month limited warranty
2. Lifetime technical support