ARRIS VIP7300 Set-Top Box Manual

In the box

Rear panel

INSTALLING YOUR SET-TOP BOX

1. Connect one end of the HDMI cable to the HDMI port on your set-top box and the other end to the HDMI connector on to your TV.
   To display a picture from your set-top box, your TV must be switched to the correct external input. This is either done automatically or manually, using a button on the TV remote control. See your TV user’s guide for instructions.
2. Connect your set-top box to your home Wi-Fi network.
   Alternatively: Connect one end of the Ethernet cable (not included) to the Ethernet port on your set-top box and the other end to your home router.
   NOTE: When removing the Ethernet/LAN cable make sure to firmly press the underside latching tab on the Ethernet/LAN cable; to unlock the cable from the Ethernet/LAN port on the product.
3. Connect one end of the power supply to POWER port on your set-top box and to the power outlet.
4. Insert the batteries into your remote control.
   The remote control will initiate pairing with your set-top box when batteries are inserted and any key is pressed.

NOTE:
Do not use any power supply other than the one supplied with the product. Doing so may cause fire or seriously damage your set-top box.

IMPORTANT SAFETY INSTRUCTIONS

• Never place the product on top of or close to any heat sources such as other electronic devices. Doing so will reduce lifetime and may cause irreparable damage or malfunction. Do not use the product near water. Note that the ambient temperature must be below 104° F/40 C. Be sure to maintain necessary space around the product to allow for proper ventilation.
• Never use the product outside. The product is designed to stand on a horizontal surface.
• Do not use any power supply other than the one supplied with the product. Doing so may cause fire or seriously damage the product.

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures.

• Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• .Consult the dealer or an experienced radio/ TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

IC Warning

– English: ”
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Ambient operating temperature	0 °C to +40 °C
Voltage	100-240 V~,50/60 Hz, 1A max
Power supply unit	This Class II product, VIP7300, shall be powered by the Limited Power Supply that is provided together with the product.
Maximum Power consumption	12 W

The following table shows the maximum EU RF Output Power:

Frequency Band (GHz)	Maximum RF Power (dBm)
2.4 to 2.48	10
5.150 – 5.350*	23
5.470 – 5.725	23
*Indoor use only BE, BG, CZ, DK, DE, EE, IE, EL, ES, FR, HR, IT, CY, LV, LT, LU, HU, MT, NL, AT, PL, PT, RO, SI, SK, FI, SE, and UK(NI).

© 2022 CommScope, Inc. All rights reserved.
ARRIS and the ARRIS Logo are trademarks of CommScope, Inc. and/or its affiliates. All other trademarks are the property of their respective owners.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.