DMP XR150 CONTROL PANEL Manual

DMP XR150 CONTROL PANEL

IDENTIFY PANEL COMPONENTS

Identify the following panel components using the panels in front of you, or the on-screen photo of the XR.

AC Power terminals
Cellular pins
100 Series antenna
Reset header
On-board zone
Programming
header
terminals
Network connection
EXP header
Outputs
Connection

POWER UP THE CONTROL PANEL

Connect AC power to terminals 1 & 2
1. Transformer type: 16.5VAC 50VA
Connect battery backup to terminals 3 & 4
Connect alarm bell to terminals 5 & 6
1. Normal 12VDC is supplied to terminal 5, terminal 6 is the ground reference
2. 1/2 W 1K Ohm resistor should be added across the bell circuit for supervision

ENTER PANEL PROGRAMMER

Reset the panel using the RESET JUMPER
Enter 6653 (PROG) and press CMD
Press CMD to navigate through the panel programmer menus:
- Initialization
- Communication
- Network Options
- Device Setup
- Remote Options
- System Reports
- System Options
- Bell Options
- Output Options
- Output Information
- Output Groups
- Status List
- Menu Display
- PC Log Reports
- Area Information
- Zone Information
- Stop
- Set Lockout Code
- Feature Upgrade

ADJUST COMMUNICATION TYPE

Navigate to COMMUNICATION and press a top-row select area
Press a top-row select area to clear the default ACCOUNT NUMBER
Enter in an ACCOUNT NUMBER
Press CMD to navigate to PATH
Press 1 to program PATH 1
Press a top-row select area to display the COMMUNICATION types
Select NET
Press CMD to navigate to RECEIVER IP
Press a top-row select area and enter in the DMP Tech Support receiver IP Address
1. 209.248.148.051 (Port 2001)
Press CMD to exit COMMUNICATION

ADD A KEYPAD

Navigate to DEVICE SETUP and press a top-row select area
Enter a DEVICE NUMBER and press CMD
1. The valid range for an XR150 panel is 1-8, XR550 is 1-16
Press a top-row select area and enter a DEVICE NAME
Press CMD to confirm the DEVICE TYPE
Press CMD to exit DEVICE SETUP

ADJUST THE KEYPAD ADDRESS

GRAPHIC TOUCHSCREEN KEYPAD

Select OPTIONS from the carousel
Select the INSTALLER OPTIONS icon
Enter 3577 (INST) and press CMD
Select KEYPAD OPTIONS (KPT OPT)
Press a top-row select area and enter a new keypad address
Press CMD to exit Keypad Options
Select STOP to save keypad programming

THINLINE KEYPAD

Press and hold the BACK ARROW and CMD for 2 seconds
Enter 3577 (INST) and CMD
Select KEYPAD OPTIONS (KPD OPT)
Press a top-row select area or key to change the keypad address
Press CMD to exit KEYPAD OPTIONS
Select STOP to save keypad programming

CONFIGURE SYSTEM OPTIONS

Navigate to SYSTEM OPTIONS and press a top-row select area
Press CMD to navigate to ENTRY DELAY 1
Press a top-row select area and choose a time from 30 to 250 seconds
Repeat this process for ENTRY DELAY 2
Press CMD to navigate to HOURS FROM GMT
Press a top-row select area, enter in the hours from GMT for your location and press CMD
Using CMD, navigate to HOUSE CODE
Press a top-row select area and enter a house code from 1-50 and press CMD
Using CMD, navigate to ENTER WEATHER ZIP CODE
Press a top-row select area and enter a local ZIP code to display weather alerts on the keypad

ADD AN AREA

Navigate to AREA INFORMATION and press a top-row select area
Enter an AREA NUMBER and press CMD
Press CMD until EXIT DELAY displays
Press a top row select key or area and enter a time between 45 and 250 seconds
Press a top-row select area to clear any text and enter in a new area name
Exit AREA INFORMATION and navigate to STOP to save changes

ADD A WIRELESS ZONE

Navigate to ZONE INFORMATION and press a top-row select area
Enter a ZONE NUMBER and press CMD
Press a top-row select area and enter a ZONE NAME
Press a top-row select area and select a ZONE TYPE
Press the top-row select area to display the list of available areas and select the appropriate area
At the NEXT ZONE? prompt, select NO to program a wireless zone
At the WIRELESS? prompt, select YES and press CMD
Enter a SERIAL NUMBER and press CMD to navigate to the NEXT ZONE? Prompt

ADD A WIRED ZONE

Add ZONE 1 as a hard-wired zone in the ZONE INFORMATION menu
- EOL resistor value defaults to 1k, but you can change the value up to 2.2k for taking over an existing panel in System Options.

STANDARD WALK TEST

At the keypad, enter 8144 (WALK) to enter the WALK TEST menu
Select STD to begin the standard walk test
Trip wired and wireless zones to complete the standard walk test

WIRELESS CHECK-IN TEST

At the keypad, enter 8144 (WALK)
Select WLS to begin the wireless check-in test

PIR WALK TEST

At the keypad, enter 8144 (WALK)
Select PIR to begin the PIR walk test

DIAGNOSTIC MENU

At the keypad, enter 2313 (DIAG) to enter the DIAGNOSTIC MENU
Press CMD until the keypad displays COMM STATUS and presses a top row select area
Press 1 to test COMMUNICATION PATH 1
When the signal strength is displayed, select YES to continue the test
1. Cellular Communication Only
Press CMD and select STOP to exit the DIAGNOSTIC MENU

EDIT AREA NAMES

Press CMD to navigate to AREA INFORMATION
Press a top-row select area to enter AREA INFORMATION
Enter an AREA NUMBER and press CMD
Press CMD until EXIT DELAY displays
Press a top row select key or area and enter a time between 45 and 250 seconds
Press a top-row select area to clear any text and enter in a new area name
Exit AREA INFORMATION and navigate to STOP to save changes
Arm, disarm, and trip an alarm in the Area system type

ARM and DISARM

Arm the system, trip an alarm and disarm

CHANGE THE SYSTEM TYPE TO A/P

Enter the panel programmer by entering 6653 (PROG) at the keypad
Navigate to SYSTEM OPTIONS and press a top-row select area
Press a top-row select area to display the list of system types
Select A/P as the system type
Exit SYSTEM OPTIONS and navigate to STOP to save changes
Arm, disarm and trip an alarm in A/P system type

CHANGE THE SYSTEM TYPE TO H/S/A

Enter the panel programmer by entering 6653 (PROG) at the keypad
Navigate to SYSTEM OPTIONS and press a top-row select area
Press a top-row select area to display the list of system types
Select H/S/A as the system type
Exit SYSTEM OPTIONS and navigate to STOP to save changes
Arm, disarm and trip an alarm in the H/S/A system type

CREATE A SCHEDULE

At the keypad, press CMD until the USER MENU?prompt displays
Select YES and enter 99+CMD to enter the USER MENU
Using CMD, navigate to SCHEDULES? and press a top-row select area
Select TIMES
To create a time schedule, select ADD
Press 1 to create Schedule 1
Press a top row area to name the schedule ACCESS
Press CMD and select a day of the week.
Enter the BEGIN and END times for the chosen day
Set times for each day of the week
Create another schedule named LIGHTS

CREATE A PROFILE

At the keypad, press CMD until the USER MENU?prompt displays
Select YES and enter 99+CMD to enter the USER MENU
Using CMD, navigate to PROFILES? and press a top-row select area
Select ADD and enter 11 to create Profile 11
Press a top row area to name the profile ACCESS
Assign ARM/DISARM AREA 2 and press CMD
Assign ACCESS AREA 2 and press CMD
Press CMD until DISARM? displays and select YES
Navigate to DOOR ACCESS and confirm it is set to YES
Navigate to FIRST ACCESS SCHEDULE and press the third select area to enter the schedule number for the access schedule
LIST will show the schedule names
Press CMD until PROFILE 11 ADDED is displayed
Create another profile named MANAGEMENT using Profile 12
1. The instructor will provide settings for this profile
  ADD A USER CODE WITH A PIN
Enter the USER MENU and navigate to the USER CODES? prompt
Press a top-row select area to add a USER CODE
Select ADD
Select the USER NUMBER and press CMD
1. The fourth top row select area will display the lowest available user number
Enter in a 5-digit user code and press CMD
Press a top-row select area to add a USER NAME and press CMD
Press a top row select area and enter 12 to assign PROFILE 12 to this user
1. LIST will display the profile names
Press CMD until USER ADDED displays

ADD A USER CODE WITH A CARD

Enter the USER MENU and go to USER CODES?
Press a top-row select area to add a USER CODE
Select ADD
Select the USER NUMBER and press CMD
Scan the card by waving it over the blue status LED
Press a top-row select area and add a USER NAME and press CMD
Press a top-row select area and enter 11 to assign PROFILE 11 to this user.
Press CMD until USER ADDED displays

PROGRAM AN ANNUNCIATOR OUT-PUT

Remove all power from the panel
Connect a 4-wire harness to the OUTPUTS header on the panel
Connect the POSITIVE leg of the LED to the RED terminal on the panel
Connect the other leg of the LED to OUTPUT 3 on the panel
Power the panel back up
Enter the Programmer by entering 6653 (PROG) at the keypad
Navigate to AREA INFORMATION and press a top-row select area
Navigate to settings for AREA 1
Navigate to ARMED OUTPUT and press a select area to clear the current setting
Set the output to 3
Navigate to STOP to save changes and exit the Programmer
Arm AREA 1 to confirm the output is working

PROGRAM A RELAY

Remove all power from the panel
Plug a MODEL 305 relay into the socket for OUTPUT 1
1. Make sure the relay is oriented correctly
Connect the MODEL 431 harness to the header between the output sockets
Connect the POSITIVE leg of the LED to the RED terminal on the panel
Connect the other leg of the LED to the second ORANGE wire on the harness
Connect the second GRAY wire to the BLACK terminal on the panel
Power the panel back up
Enter the Programmer by entering 6653 (PROG) at the keypad
Navigate to ZONE INFORMATION and press a top-row select area
Navigate to settings for ZONE 1
Program ZONE 1 as a NIGHT type zone in AREA 1
At the NEXT ZN? prompt, select NO
Navigate to DISARMED SHORT and press CMD until OUTPUT NO is displayed
Press a select area to set the output to 1.
Set the output action to FOLLOW
Navigate to STOP to save changes and exit the Programmer
Press the button to trip ZONE 1.
1. Notice the output state follows the zone state.

CREATE AN OUTPUT SCHEDULE

Enter the user menu and press CMD until SCHEDULES? is displayed.
Press a select area, then select TIMES, then ADD.
Enter 1 for the schedule number, then name the schedule LED.
Set begin and end times for each day of the week.
When all times are set, press the BACK ARROW until SAVING SCHEDULES is displayed on the keypad.
Re-enter the schedule programming section. Press CMD and select OUTPUT.
Enter output 1, then schedule 1.
Press the BACK ARROW to exit scheduled programming.
Advance panel time to test the beginning and end times for the schedule.

QUESTIONS

What else would you like to learn about the XR series?

DMP XR150 CONTROL PANEL Manual