Dyson HP01 Pure Hot + Cool Purifier Heater Manual

REGISTER TODAY
3 easy ways to register your 2-year limited warranty.

IMPORTANT SAFETY INSTRUCTIONS
WHEN USING ELECTRICAL MACHINES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO PERSONS INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.

WARNING
THE MACHINE AND THE REMOTE CONTROL BOTH CONTAIN MAGNETS.

Pacemakers and defibrillators may be affected by strong magnetic fields. If you or someone in your household has a pacemaker or defibrillator, avoid placing the remote control in a pocket or near to the device.
Credit cards and electronic storage media may also be affected by magnets and should be kept away from the remote control and the top of the machine.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:
This Dyson machine is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction by a responsible person concerning the use of the machine to ensure that they can use it safely.
Do not allow it to be used as a toy. Close attention is necessary when used by or near children. Children should be supervised to ensure that they do not play with the machine.
Always plug this machine directly into a wall outlet/receptacle. Never use an extension cord or relocatable power tap (outlet/power strip).
This machine must not be located immediately below a socket outlet.
If there is a loose fit between the plug and the outlet or the plug becomes very hot, the outlet may need to be replaced. Check with a qualified electrician to replace the outlet.
CAUTION – Risk of electric shock, do not open the machine, and no user-serviceable parts inside.
This machine is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. When moving the machine, hold it by the base and not the air loop amplifier. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the machine and keep them away from the sides and rear.
This machine has hot parts inside. Do not use it in areas where petrol, paint, or flammable liquids are used or stored or where their vapors are present.
Extreme caution is necessary when any machine is used by or near children or infirm persons and whenever it is left operating and unattended.
Do not operate any machine with a damaged cord or plug or after the machine malfunctions, or has been dropped or damaged in any manner. Discard the machine, or return it to an authorized service facility for examination and/or repair.
Do not run the cord under the carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not route the cord under furniture or machines. Arrange the cord away from traffic areas and where it will not be tripped over.
To avoid a tripping hazard, wind the cord when not in use.
This machine is not intended for use in bathrooms, laundry areas, and similar indoor locations. Never locate the machine where it may fall into a bathtub or other water containers. Do not store this machine in the immediate surroundings of a bath, shower, or swimming pool.
WARNING: In order to avoid overheating, do not cover the machine.
To prevent a possible fire, do not block air intakes or exhausts in any manner. Do not use it on soft surfaces, like a bed, where openings may become blocked.
Use this machine only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
Do not use this machine if it has been dropped or if it has visible signs of damage.
Always use this appliance on a horizontal and stable surface.
Do not use it outdoors or on wet surfaces and do not handle any part of the machine or plug with wet hands.
Keep this machine and cord away from heated surfaces. Do not position the cord under the furniture or machines.
If the supply cord is damaged, it must be replaced or repaired by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
Do not use this machine if it has been damaged or submerged in water.
Do not put any objects into any opening as this may cause an electric shock or fire, or may damage the machine.
Disconnect power or unplug before cleaning, performing any maintenance or replacing a filter. Always unplug the machine when not in use.
Chemical Burn and Choking Hazard. Keep batteries away from children. This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Even used batteries may cause injury. POLARIZATION INSTRUCTIONS
To reduce the risk of electric shock, this machine has a polarized plug (one blade is wider than the other) as a safety feature. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not attempt to defeat this safety feature and do not change the plug in any way.
SAVE THESE INSTRUCTIONS

Each time the heating mode is selected, it conducts a short calibration cycle. Airflow will be automatically controlled during this cycle. Once the calibration cycle is complete, it will revert to the selected airflow speed. On first use, the machine will default to a temperature 3°C higher than the detected room temperature.
Thereafter, the machine will remember the last target temperature set.
Select the desired room temperature using the Thermostat control button. Press the large red button on the remote control to increase the target temperature by 1°C; press the small red button on the remote control to decrease it by 1°C. The machine will not operate in heating mode unless the target temperature is above room temperature.

Remote control

Remote control docks magnetically
Attach the remote control to the top of the machine with the buttons facing down.

Airflow speed control

Press the red Thermostat control button until the digital display shows the target room temperature. The power button light will change from blue to red to indicate that you have entered the heating mode. The heating symbol will be red while heating and will change to white when the target room temperature has been reached. Once the target room temperature has been reached, the machine will stop heating the air. If the room temperature falls below the target temperature, the machine will start to heat again. The red circle surrounding the power button remains on when the machine is in heating mode. To adjust the airflow speed, use the airflow control button.

Press the blue Cooling mode button to enter cooling mode. The power button light will change from red to blue to indicate that you have entered the cooling mode. To adjust the airflow speed, use the airflow control button.

Sleep timer

Tilt function

To set the sleep timer, select the desired time. When the time reaches zero, the machine will go into standby mode. To cancel, increase the time until two dashes appear.
When using the sleep timer, the LED display will turn off after 10 seconds of inactivity.
Carefully hold the base and the main body. Tilt the loop amplifier forward or backward for the required airflow angle.

Diffused and Focused modes

Diffused mode
Press the wide-angle button to change from a personally directed airflow to a whole room airflow. Heating and cooling modes work in this mode.

Oscillation and Airflow speed control

Oscillation control
To start the machine oscillating, Press the Oscillation control button. To stop the machine from oscillating, press it again. The machine will not oscillate when the control buttons are pressed

Focused mode
Press the narrow-angle button to change from a whole room airflow to a personally directed airflow. Heating and cooling modes work in this mode.

Airflow speed control
To change the airflow speed, press the Airflow speed control button. The digital display will show the new fan speed. If in heating mode, after 3 seconds it will change back to displaying the target temperature

Cleaning

Unplug from the main power source. If the machine has been in use, leave it for 1 to 2 hours before cleaning to allow the machine to cool completely. Dust may accumulate on the surface of the machine. Wipe dust from the loop amplifier, filter unit, and other parts with a dry or damp cloth when dust accumulates. Do not use detergents or polishes.

Clearing blockages
Unplug from the main power source. If the machine has been in use, leave it for 1 to 2 hours in order to allow the machine to cool down completely. Look for blockages in the air inlet holes and in the small aperture inside the air loop amplifier. Use a soft brush to remove debris.

Caution: Hot when in use
This machine is hot when in use and for a short period after use. Do not let bare skin touch hot surfaces. If children are present, consider positioning the machine out of their reach.

Battery replacement
Unscrew the battery compartment on the remote control. Loosen the base and pull to remove the battery.

Replacing the filter unit

When your non-washable filter unit needs replacing the machine will display the pattern shown. To replace the non-washable filter unit, follow these steps. If the machine has been in use, leave it for 1 to 2 hours before replacing the filter unit to allow the machine to cool down completely. Your Dyson machine is programmed to remind you to replace the filter unit after 12 months based on 12 hours of usage a day. Please note that your indicator will activate sooner with more use. The indicator is only a guide. Use in heavily polluted environments may require the filter unit to be replaced more regularly.

When you have reassembled your machine, press and hold the Standby on/off button for 6 seconds on the remote control to reset the filter indicator.

USING YOUR DYSON MACHINE
PLEASE READ THE ‘IMPORTANT SAFETY INSTRUCTIONS’ IN YOUR DYSON USER MANUAL BEFORE PROCEEDING. LOOKING AFTER YOUR DYSON MACHINE

Do not carry out any maintenance or repair work other than that shown and described in your Dyson User manual, or advised by the Dyson Helpline.
Always disconnect the plug from the mains outlet before inspecting for problems. If the machine will not operate, first check that the mains outlet has an electricity supply and that the plug is properly inserted into the outlet.
If the fuse needs replacing, please check ‘User servicing instructions’.

OPERATION

Ensure that the machine is fully assembled in line with the instructions before use.
Do not dismantle the machine or use it without the loop amplifier fitted.
The machine will not operate in heating mode unless the target temperature is above room temperature.
Each time the heating mode is selected, it conducts a short calibration cycle. Airflow will be automatically controlled during this cycle. Once the calibration cycle is complete, it will revert to the selected airflow speed.
The machine will not oscillate when the control buttons are pressed.
Do not lubricate any part of this machine.

CONTROL WITHOUT REMOTE

Press the power button on the machine to turn on/off.
Press and hold the power button on the machine to adjust the target temperature.
The target temperature will increase to a maximum before decreasing. If the target temperature is set at 0°C it will switch from heating to cooling mode.
The airflow, diffused and personal heating modes, oscillation function, and sleep timer controls cannot be operated without the remote control.

LED DISPLAY

The LED display will dim after 10 seconds of use.
Press any button, other than the Standby ON/OFF, to reactivate.
Do not press Standby ON/Off as this will turn the machine off.

SLEEP TIMER
To set the sleep timer, press and hold the Sleep timer button to select the desired time. When the time reaches zero, the machine will go into standby mode. To cancel, reduce the time until two dashes appear.

The LED display will turn off after 10 seconds of inactivity – this is a power-saving feature and avoids light interference at night time.
Press any button, other than the Standby ON/OFF, to reactivate.
When the sleep timer is ON, do not press the Standby ON/OFF as this will turn the machine off and turn the sleep timer off too.

TILT FUNCTION
Carefully hold the base and the main body. Tilt the loop amplifier forward or backward for the required airflow angle.

AUTOMATIC CUT-OUT
For your safety, this machine is fitted with automatic cut-out switches that operate if the machine tips over or overheats. If the switches operate, unplug the machine and allow it to cool. Before restarting the machine, check and clear any blockages and ensure that the machine is on a solid level surface. In heating mode, the machine will automatically switch off after 9 hours of continuous use and will return to standby mode. To restart the machine, press the power button on either the remote control or the base.

TROUBLESHOOTING

Fault codes F4, F5, and F6: If one of these appears on the display, unplug the machine, wait for 30 to 60 seconds, and/or plug the machine into a different socket. If you continue to receive the fault code, please contact the Dyson Helpline.
Fault codes F2, F3, and F7: If one of these appears on the display, please contact the Dyson Helpline.

REPLACEABLE PARTS BATTERY REPLACEMENT
CAUTION

Switch off and unplug the machine before replacing the batteries.
Unscrew the battery compartment on the remote control. Loosen the base and pull to remove the battery.
Do not install backward or short-circuit the batteries.
Do not attempt to dismantle or charge the batteries. Keep away from fire.
Always replace the screw in the remote control and refer to the battery hazard in the warning section.
Follow battery manufacturers’ instructions when installing new batteries (battery type CR 2032).
Limited functionality is available without the remote control (see ‘Control without remote’).

NON-WASHABLE FILTER UNIT

Your filter unit is non-washable and non-recyclable.
To replace your filter unit follow the steps as shown.
Failure to replace the filter when prompted may result in changes to the product

DISPOSAL INFORMATION

Dyson products are made from high-grade recyclable materials. Recycle where possible.
Dispose of or recycle the battery in accordance with local ordinances or regulations.
Keep the used batteries away from children as these can still harm children if swallowed.
Your filter units are non-washable and non-recyclable.
Dispose of the exhausted filter units in accordance with local ordinances or regulations.
The battery should be removed from the machine before disposal.

DYSON CUSTOMER CARE

THANK YOU FOR CHOOSING TO BUY A DYSON MACHINE.
After registering your 2-year warranty, your Dyson machine will be covered for parts and labor (excluding filters) for 2 years from the date of purchase, subject to the terms of the warranty. If you have any questions regarding your Dyson machine, visit www.dyson.com.mx for online help, general tips, and useful information about Dyson. Alternatively, you can contact us via email or phone with your serial number and details of where and when you bought the machine. If your Dyson machine needs a repair, email or phone Dyson so we can discuss the available options. If your Dyson machine is under warranty, and it is a covered repair, it will be repaired at no cost. Your serial number can be found on your rating plate which is on the base of your machine.

PLEASE REGISTER AS A DYSON MACHINE OWNER
To help us ensure that you receive prompt and efficient service, please register as a Dyson machine owner.

Online at www.dyson.com.mx/register
Register by phone: 01 800 872 0154
This will confirm ownership of your Dyson machine in the event of an insurance loss, and enable us to contact you if necessary.

IMPORTANT DATA PROTECTION INFORMATION
WHEN REGISTERING YOUR DYSON MACHINE:

You will need to provide us with basic contact information to register your machine and enable us to support your warranty.
When you register, you will have the opportunity to choose whether you would like to receive communications from us. If you opt-in to communications from Dyson, we will send you details of special offers and news of our latest innovations.
We never sell your information to third parties and only use information that you Share with us as defined by our privacy policies which are available on our website at privacy.dyson.com

ELECTRICAL SPECIFICATIONS
CONNECTION INSTRUCTIONS

Connect the plug on the power cord to a 127V AC power socket
Do not unplug by pulling on the cord, firmly grasp the plug and remove it gently.
Unplug the device from the AC power socket if you are not going to use the product for an extended period

THANK YOU FOR CHOOSING TO BUY A DYSON MACHINE
After registering your free 2-year warranty, your Dyson machine will be covered for parts and labor (excluding filters) for 2 years from the date of purchase, subject to the terms of the warranty. If you have any questions about your Dyson machine, please contact Dyson Customer Care with your serial number and details of where and when you bought the machine. Most questions can be solved by one of our trained Dyson Customer Care staff. Your serial number can be found on your rating plate which is on the base of the machine. Visit www.dyson.com.mx/support for online help, support videos, general tips, and useful information about Dyson Note your serial number for future reference.

This illustration is, for example, purposes only.