GE Appliances Opal 2.0 Ice Maker Manual

GE Appliances Opal 2.0 Ice Maker Instruction Manual

GE Appliances Opal 2.0 Ice Maker Instruction Manual

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
WARNING

Do not, under any circumstances, alter or remove the third (ground) prong from the power cord. For personal safety, this product must be properly grounded.
Do not exceed power outlet ratings. It is recommended that the ice maker is connected to its own circuit. Use only a 115 V. 60 Hz standard electrical supply that is properly grounded in accordance with the National Electric Code and local codes and ordinances.
Due to potential safety hazards under certain conditions. we strongly advise against the use of an extension, However, if you must use an extension cord, it is absolutely necessary that it is a UL-listed, 3-wire ground type appliance extension cord having a grounding type plug and that the electrical rating of the cord is 15 Amperes (minimum) and 120 Volts.
This product must be properly installed and located in accordance with the installation instructions before it is used Product is for indoor household use only. Do not use
Do not store or use flammable vapors or liquids near this
Do not allow children to climb, stand. or hang on the ice They could seriously injure themselves.
Do not look directly at the UV lamp when it is operating. The light emitted by the lamp will cause serious eye damage and burn unprotected skin.
In order to avoid exposure to UV radiation, disconnect covers.
Do not use water that is micro-biologically unsafe or of unknown quality.
Place the power cord in such a way it cannot be pulled on by children or cause a tripping hazard.
Place the power cord in such a way that it is not in contact with hot surfaces.
Do not operate if any component, including the cord or plug, is damaged.
Unplug the product before cleaning by hand and when not in use
Do not immerse any part of the product in water.
Do not plug or unplug the product with wet hands.
Do not attempt to disassemble, repair, modify. or replace any part of your product.
Use this product only for its intended purpose as described in this user manual.
Do not use any accessories not recommended by the
When handling, installing, and operating the appliance. care should be taken to avoid damage to the refrigerant
Servicing shall be performed by factory authorized service personnel and component parts shall be replaced with manufacturer authorized replacement components.

CAUTION
To reduce the risk of injury when using your Opal, follow these basic safety precautions.

Do not remove any safety. warning. or product information labels from your ice maker.
Lifting Hazard: It is recommended to have two people move and install the ice maker in order to prevent injury.

Refrigerant and Foam Disposal
Dispose of appliances in accordance with Federal and Local Regulations. Flammable refrigerant and insulation material used require special disposal procedures. Contact your local authorities for the environmentally safe disposal of your appliance.
WARNING
FIRE OR EXPLOSION HAZARD Flammable Refrigerant

This appliance contains isobutane refrigerant, also known as R600a, a natural gas with high environmental compatibility. However, it is also combustible. Adhere to the warnings below to reduce the risk of injury or property damage.

When handling, installing, and operating the appliance. care should be taken to avoid damage to the refrigerant tubing.
Service shall only be performed by authorized service personnel. Use only manufacturer-authorized service parts.
Dispose of the refrigerator in accordance with Federal and Local Regulations. The flammable refrigerant and insulation material used in this product require special disposal procedures. Contact your local authorities for the environmentally safe disposal of your refrigerator.
Keep ventilation openings in the appliance enclosures or in the built-in structure clear of obstruction.
To remove frost, scrape with a plastic or wood spatula or scraper. Do not use an ice pick or metal or sharp-edged instrument as it may puncture the freezer liner and then the flammable refrigerant tubing behind it.
Do not use electrical appliances inside the food storage compartment of the appliance.
Do not use any electrical device to defrost your appliance

READ AND SAVE THESE INSTRUCTIONS

PARTS INCLUDED

GETTING STARTED

Installation Requirements
CAUTION
Lifting Hazard: It Is recommended to have two people move and Install the Icemaker In order to prevent injury.

The product is designed to be installed indoors. Do not use your ice maker outdoors.
The product must be installed upright on a flat, level surface that is able to support the total weight when full of water.
Ensure a minimum of three inches (3″) clearance around the side and back walls of the ice maker for proper air circulation.
Install the product in a well-ventilated area with an ambient temperature between 55^°F and 90^°
Do not place the product near heat sources such as ovens or cooktops.
Do not place the product in direct sunlight.

Prepare Opal For Use

Carefully remove the packing material. Do not use sham tools that can damage the box contents.
Ensure all components are present. If any item is missing, please contact 1.866.907.6718.
Place the ice maker upright on a flat, level surface and plug it in.
Install drip tray by sliding it under the front edge of The tray slots should align with the front feet of Opal.
Sanitize and rinse the ice maker with clean water for five minutes before first use.

NOTICE
Some types of under-cabinet lamps can be hot enough to cause damage to your Opal top’s appearance.

CARE AND CLEANING

To keep your nugget ice tasting fresh and your Opal looking great, we recommend cleaning/sanitizing your Opal once per week.
To clean the exterior of the ice maker, unplug the product, then use a soft cloth dampened with soapy water to gently clean the exterior surfaces.
Dry with a soft cloth. The exterior stainless steel surfaces can be cleaned with commercially available stainless steel cleaner.
Use only a liquid cleaner free of grit and rub in the direction of the brush lines with a damp, soft sponge.
Do not use appliance wax, polish, solvents, or chemicals on the stainless steel. Do not use soap to clean the reservoir. Use a soft cloth moistened with water.
WARNING
Chemical Exposure Hazard, when cleaning with bleach, use bleach in a well-ventilated area and avoid mixing bleach with other household cleaners.
WARNING
Unplug the product before cleaning by hand, and when not in use.

System Cleaning / Sanitizing Procedure

To clean Opal’s internal components. complete the following steps:

Unplug Opal,
Remove water filter (if present). and replace with the reservoirs screened intake cap. See Figure 1.
Drain Opal (see page 8 for detailed instructions).
Create a solution of five cups of water and one teaspoon of household bleach. Skip to page 9 for further instructions on how to remove hard mineral
Pour the solution into the water reservoir, up to the fill line shown. See figure 2.
Plugin Opal and hold the ‘Clean’ button for 3 seconds to initiate the cleaning process. See figure 3
Water will begin circulating and the ‘Cleaning’ indicator will light up on the left-hand side of the unit to confirm the unit is now in the cleaning process. See figure 4. After three minutes the water will stop and the ‘Cleaning’ indicator light will turn off.
When the ‘Cleaning’ indicator light turns off. drain the
Unhook the top of the drain hoses at the back of the unit See figure 5
Then lay them down to drain into a sink or bucket that is below the level of the ice maker. See Figures 6 and 7.
Remove the plugs and allow the water to completely See figure 7.
Once the water stops flowing. re-insert the drain plugs.
To rinse: add five cups of fresh water to the water reservoir, and press the ‘Clean’ button to initiate a second cleaning cycle. To exit the cleaning cycle at any time. press and hold the ‘Clean’ button for 3
Repeat steps 8 through 13 two more times. adding fresh water to the reservoir each time (you may continue to repeat the rinse cycle. as many times as you like).
Replace drain tubes on the back. See figure 8.
When complete. fill the unit with fresh water and press the ‘Power’ button to start making ice. See figure 9.

UNDERSTANDING THE DISPLAY

Care and Cleaning

Removal of Mineral Deposits

Fill the reservoir with white vinegar to the max fill line and run up to three cleaning cycles. Or purchase an Opal Cleaning Kit and follow instructions inside.
If using vinegar. leave the vinegar in the unit for 18 hours and set a vinegar-soaked towel on the ice chute overnight to further dissolve any mineral buildup. See figure 10.
Clean the sensors with vinegar and wipe them clean with water. After draining the vinegar. run three rinse cycles. using freshwater for each rinse. See figures 11. 12. and 13 to reference the location of the sensors.

Cleaning the Bin and Tray
To clean the ice bin. remove the ice bin from the ice maker and clean with a soft cloth dampened with soapy water. Rinse thoroughly. Dry with a soft cloth. Do not use solvents or chemicals.
The drip tray should be wiped dry. Water left in this area may leave deposits. To clean the drip tray. remove the tray from Opal and use a soft cloth dampened with mild soapy water to gently clean the surface. Dry with a soft cloth. Do not use solvents or chemicals.
Understanding the display

Power
The Power button. when pressed. will begin the ice-making process. When pressed. while ON. will tum the ice maker off.
Light
The light feature has three different modes: ONIDIWOFF Toggle between the three modes by pressing the light button until you reach your desired lighting mode.
Clean
The cleaning cycle is initiated by pressing and holding the ‘Clean’ button for three seconds.
Indicator Lights
The four indicator lights on the left-hand side of the unit display the current status of the Opal. If ‘Add Water is highlighted. your unit needs more water before it can cycle to make ice or clean.
Win
Using the complimentary SmartHO mobile app. customers can connect to their Opal and control it from their Android or iPhone. The indicator light on the left-hand side will confirm a successful connection. See page 14 for how to connect Opal 2M Ice Maker to WIFi Application.

Making Ice with Opal

Once Opal has been cleaned sanitized. move the ice maker to its desired location and complete the following steps.

Remove ice bin, Fill the reservoir with potable (safe to drink) water up to the “Max Fill’ line. Water hardness must be less than 12 grains per gallon. Do not fill the reservoir with any liquid except water. Using any liquid except potable water is misuse and will void your warranty
Plug the ice maker into a grounded outlet.
Touch the Power button to start the ice maker. The indicator on the left-hand side will light up ‘Making Ice’ to confirm that unit has begun to make ice.
Opal will begin to produce ice in 15-30 minutes. It will continue to make ice until the bin is full. or it runs out of water. To continue making ice. just add more water.

Draining Opal

We recommend draining your Opal when.

You put it away or anytime it’s being relocated
You turn it off for more than a few days (i.e vacation)
You are not using much ice. Continuous recirculation of meltwater may affect the taste. For best results. drain your Opal.

Water Filter

The Opal Water Filter is available at GE Appliances and is the only water filter compatible with Opal. Please cleaning your following the installation instructions included with your filter.
NOTE: Remove your water filter (if installed) and reinstall the screened intake cap prior to Opal.

SIDE TANK ACCESSORY

NOTE: The Side Tank Accessory is only included with model numbers XPIO13BCBT and XPIO13SCSS.
NOTE: There are two drain tubes located on the back of your Opal Nugget Ice Maker indicated as drain tubes A and B in the illustration on page 11

Hand Washes Only: Rinse and hand wash Opal Side Tank with warm water and mild dish soap. Remove Opal Side Tank’s cap and wash the cap and rubber valve with water and mild dish soap. The Side Tank base can be washed by disconnecting the hose and adding a small amount of soapy water to it. Scrub as needed and rinse thoroughly. The rinse water should drain out the port in the back.
Rinse the cap. rubber valve. tank and the base well to remove any residual soap (see illustration)

DO NOT WASH THE SIDE TANK IN THE DISHWASHER.
Unplug Opal Nugget, Ice Maker. Unhook Opals drain tubes and drain the water from the reservoir.
Connect drain tube. labeled B. to the back of Opal Side Tank’s base
Make sure drain tube (A) is connected to the black hanger and installed on the back of Opal.
Make sure drain tube (B) connecting to the Side Tank is resting flat on the countertop.
Place Opal Side Tank on the right or left-hand side of the Opal Nugget Ice Maker. Us ng the side tank attachment. slide the shorter side of the attachment under the unit. near the front of the unit. The at ached will slide into a slot on the bottom of the unit. Once this is placed. the side tank can slide onto the opposite atta home. See the figures below and on the next page.

NOTE: Care should be taken to connect the correct tube to the Opal Side Tank. Tube (B) should always be connected to the Side Tank whether it is installed on the left or right side of the Opal Nugget Ice Maker. It is important to make sure the tube is lying flat, otherwise, water may not flow from the side tank into the ice maker.
Remove Opal Side Tank’s reservoir from its base.
Unscrew Opal Side Tank’s cap from the reservoir. Fill the clear reservoir with water.
Replace Opal Side Tank’s cap. Ensure the cap is clean when installing.
Carefully flip over Opal Side Tank’s reservoir and place it in the base. Water should start flowing into the Opal Nugget Ice Maker and bubbles in the Opal Side Tank will appear periodically during the time water is flowing to the ice maker.
NOTE: If water does not appear to flow into the ice maker. please check for the following.
– There may be bubbles in the tube (B) connecting the Side Tank to the Opal.
– Tube (B) is not lying flat.
If either of the above issues is present. adjust tube (B) to allow the water to flow
Fill Opal Nugget Ice Maker’s reservoir (if desired).
Plugin Opal Nugget Ice Maker. and begin making ice.

WARNING
To reduce the risk of electrical shock or in safety precautions:

Unplug the product before cleaning by hand and when not in use.
Do not use water that is microbiologically unsafe or of unknown quality.
Use caution when filling and installing Opal Side Tank. as the filled unit may be heavy.
Do not use this side tank for any liquid other than water.
Children should not fill or install Opal Side Tank. as the filled unit may be heavy.
The side tank should be assembled to an ice maker per installation instructions. Installing the side tank in a different manner may result in overturning the risk.
Make sure that Opal Nugget Ice Maker is unplugged when draining the reservoir and installing Opal Side Tank.
Ensure that Opal Side Tank is installed on a level surface that will be stable even when Opal Side Tank is full.
Make sure the cap of the Side Tank remains clean during filling and operation. Hands should be washed and clean prior to opening and closing the cap.

Use and Care
Cleaning the Side Tank

Remove and drain the Side Tank.
If there is residual water in the Opal Side Tank base unit. flip Opal Side Tank’s base to drain.
Remove and wash Opal Side Tank’s cap and valve with dish soap and warm water as needed. Ensure the cap is clean after removing and re-installing by hand.
Only remove drain tubes while near a sink or bucket. as removing drain tubes from Opal or Opal Side Tank will drain any water in either unit.

Proper Installation and Location
The side tank should be installed flush to the front of the Opal Nugget Icemaker. Opal Side Tank needs to sit on the same level surface as your Opal Nugget Ice Maker. Do not elevate Opal Side Tank. or your Opal may overflow.
To Remove Mineral Deposits:
Mix two quarts of water with two quarts of white vinegar. OR use the Opal Cleaning Kit.
Clean any visible mineral buildup or deposits with this solution. If deposits are present in the tank, fill the tank with this solution and let soak. Be sure to drain and rinse the tank thoroughly after cleaning. Stubborn deposits may require more than one treatment
Side Tank Troubleshooting
If water does not flow from the Side Tank to the Opal Ice Maker:
There may be bubbles in the tube connecting the side tank to the Opal if the tube is not lying flat. Try adjusting the tube to allow the water to flow. Once the water starts flowing it typically will not need further adjusting.

TROUBLESHOOTING

Normal Operating Sounds
Your new ice maker may make sounds that are not familiar. floor, walls, and countertops can amplify these sounds. And what may be creating them?

WHIR – When Opal is first turned on, you may notice the condenser fan spinning.
BUZZ – When the water pump first tums on, it may be dry and slightly noisy. Once it is filled with water, the noise reduces significantly.
RATTLE – Rattling noises may be produced from the flow of the refrigerant. These noises should reduce significantly once the refrigerant system has stabilized.
GURGLE – When the refrigerant system shuts off, there may be a brief gurgle as the refrigerant stops flowing.
HUM – The compressor is a motor. It produces a low-toned humming sound while it is running.
CLICK – As nugget ice is produced, it drops into the ice The first nuggets produced are the loudest, as they impact the bottom of the ice bin. As the bin fills, this noise reduces significantly.
SQUEAK — When Opal is in need of defrosting, it may start to squeak as the ice starts to build up around the mechanisms. The defrost cycle is automatic and may take 30-45 minutes. During this time, the front button won’t respond. More frequent squeaking usually requires white vinegar cleaning to remove internal mineral scale buildup.

Radio Frequency Interference
This product has been tested and found to comply with the limits set forth in Title 47 CFR Part 15 – Radio
Frequency Devices. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product generates, uses, and can radiate radio frequency energy, and if not used in accordance with the instructions, may cause harmful interference to radio communications. If this product does cause harmful interference to radio or television reception, which can be determined by unplugging Opal, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the N or radio antennas.
Increase the distance between the product and N or radio.
Plug Opal into a separate outlet from a radio or N.

The transmitter must not be co-located or operating in conjunction with other antennas or transmitters.

WiFi Connect — SmartHQ
Your OPAL 2.0 ice maker is WiFi Connect Enabled. A WiFi communication card is built into the product allowing it to communicate with your Smart Phone for remote monitoring, control, and notifications.
Please visit geappliances.com/ge/connected-appliances/ to learn more about connected appliance features and to learn what connected appliance apps will work with your Smart Phone.

ICE MAKER PRODUCT SPECIFICATIONS

Description of product	Portable nugget ice maker
Model	XPIOI3BCBT / XPI013SCSS I XPIO23BCBT I XPIO23SCSS
Voltage/Frequency	120V AC/60Hz
Current	3.0 A
Ice storage capacity	3.0 lbs
Ice making rate	24 lbs per day / 1Ib per hour’
Dimensions (width x depth x height)	13.43 x 17.5 x 16.5
Installation clearance (sides and back)	3 in
Operating environment	55T – 90’F
Weight (when empty)	38.6 lbs

NOTE: Technical data and performance information provided for reference only.
Specifications are subject to change. Check the rating label on your ice maker for the most accurate information.
*The actual quantity of ice produced will vary with environmental conditions.
Note: Products containing refrigerants
This product contains a refrigerant. which under Federal Law must be removed prior to product disposal. If you are disposing of this. or any refrigeration product, check with your local waste company for guidance.
WARNING
In order to avoid exposure to UV radiation, disconnect power to the ice maker before removing the external covers.

Do not attempt to repair or replace the UV lamp

NOTES

LIMITED WARRANTY

GE Appliances Ice Maker Limited Warranty
GEAppliances.com
Please have your serial number and your model number available when calling for service. Call 1.866.907.6718 for service questions.

For the Period of:	GE Appliances Covers
One Year From the date of the original purchase	If the ice machine fails due to a defect in materials or workmanship. during the limited one-year warranty, GE Appliances will either replace your product with a new or remanufactured product. or refund the purchase price of the product at GE Appliances sole discretion.

What GE Appliances Will Not Cover:

Service trips to your home.
Improper installation, delivery, or maintenance.
Failure of the product if it is abused, misused, or used for other than the intended purpose or used
Replacement of house fuses or resetting of circuit
Damage caused after delivery.
Replacement of the light bulbs, if included.
Damage to the product caused by accident. fire, floods, or acts of God.
Incidental or consequential damage caused by possible defects with this appliance.
Software bugs that can be corrected with an update via the SmartHQ App
Labor and other charges to install and/or remove the product

EXCLUSION OF IMPLIED WARRANTIES
Your sole and exclusive remedies are product exchange or refund as provided in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law.
For sale in the 50 United States and the District of Columbia only: For US Customers: This limited warranty is extended to the original purchaser for products purchased for home use within the USA. In Alaska and Hawaii. the limited warranty does not include the costs of shipping units.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Staple your receipt here. Proof of the original purchase date is needed to obtain service under the warranty.

CONSUMER SUPPORT

Service and Registration
Register your new appliance online at your convenience! Timely product registration will allow for enhanced communication and prompt service under the terms of your warranty, should the need arise.
Register your appliance at GEAppliances.com/regIster or visit myopalservlce.com to submit a service request.
Contact Us
If you are not satisfied with the service you receive from GE Appliances, contact us on our Website with all the details including your phone number, or write to:
In the US: General Manager, Customer Relations I GE Appliances, Appliance Park I Louisville, KY 40225 GEAppllances.com/contact
In Canada: Director, Consumer Relations, MC Commercial Inc. I Suite 310, 1 Factory Lane I Moncton, N.B. E1C 9M3 GEAppllances.ca/en/contact-us

FAQS

Does this machine come with 5 year amazon warranty?? these machines don’t last much longer than a year. there’s no way i’d buy this model without one

I purchased a square trade (Allstate) 4 year warranty from Amazon $60. With all the people reporting problems wouldn’t buy it without extending warranty

Is it refrigerated

No, the container is not refrigerated, but that does not seem to be a problem. In the morning, the tub is about half full. I stir it up and the maker gets to making. What melts returns to the system to be made into nuggets again. I too was worried, but it’s not an issue.

What is the difference between this one and the previous version?

There are a number of differences between the Opal models. Some of these differences include -OPAL01GEPKT has a large round control button in the front with an lighted LED display ring that shows the status of the icemaker. The XPIO models do not have a round button; they have control pads at the top right corner and shows the status at the top left corner. The side tank attaches differently. The XPIO models are available in Black Stainless and Stainless while the OPAL01GEPKT is available only in Stainless. The OPAL01GEPKT connects to a smartphone using bluetooth technology and the GE Profile Opal app. The XPIO models are Wi-Fi enabled and connect to a smartphone and the SmartHQ™ app. The SmartHQ app is our Smart Home app and allows control of our smart appliances. Also, the XPIO models are slightly smaller and not as heavy as the older machine. All of our Opal icemaker offer the “good ice” and we’re confident once of these models will fit your needs. Kind regards

Does this have the cleaning cycle with uv light?

Skip the scrubbing thanks to an advanced, self-cleaning system that keeps your ice maker mold and mildew free when paired with the Opal Cleaning Kit and built in UV light that has the ability to limit bacteria.”
You also make up a bleach solution when you want to clean machine.

Why do the ice maker light cone on blue it is getting water to it an not making ice very fast

The light you’re describing usually means the unit needs water. If you’re seeing it even though the unit is full of water, we’d recommend contacting Opal Support for additional troubleshooting. They can be reached by calling 1-866-907-6718 (Monday – Friday, 8 AM – 8 PM EST). Kind regards – Vikki@GEA

Is this 17.5 tall?

This unit is 16.5” tall and has overall dimensions of 16.5” H x 13.43” W x 17.5” D. We hope this helps, and are confident this ice maker would be a great fit for your needs! If you have any other questions or concerns, we’re always happy to offer assistance.

What do you need the side tank for ?

It keeps the machine supplied with ice. If you don’t have the side tank, you will be filling the internal tank quite often.

when we remove ice bin and replace it. the unit sprays water into the bin and melts remaining ice. Is this normal operation?

he only time the unit has pumped water into the ice hopper, it was at the beginning of the cycle to get the water back down to the bottom reservoir. It looked like it was trickling down the back wall of the ice hopper. If it’s spraying, it might possibly be clogged. If it’s new, not normal behavior that I’ve experienced.

How do i fix the problem of the buckets getting condensation on the back making the sensor think its full of ice? Hence i get very small amouts of ice

As soon as it gets full empty it because if you let the ice sit *& it starts to melt condensation is going to happen. Just empty it & dry it off when it gets full.

Why does my add water light stay on continuously even though it has plenty of water?

The line from your side tank needs to be flat on the surface of your counter. You could also have an air bubble in the tube, just squash the tube multiple times.

Ordered this and it is broken how do I send it back

Contact GE

Does this machine require a drain hose?

Two hoses are attached, one is connected to the water storage container. Both are used to drain the system when cleaning. I would suggest setting the ice maker up near a sink. Will make it easier

Does this have a Proposition 65 warning?

Yes, the Opal icemaker does come with a Prop 65 warning.

While making ice and you need to refill with water do you have to turn opal off then back on?

It is not necessary to turn the unit off when refilling with water. When the ice bin is removed, ice making operation ceases until water is added and the bin has been reinstalled. We appreciate you checking with us.

Is there a way to run a water line to this system?

No, there isn’t an approved method of running a water line to the unit. We are glad you checked with us.

VIDEO

Write the model and serial numbers here:
Model # _________________
Serial # _________________
Find these numbers on a label on the back of the unit.
GE is a trademark of the General Electric Company. Manufactured under trademark license.
49-1000464 Rev. 4 02-21 GEA

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.
We take pride in the craftsmanship, innovation, and design that goes into every GE Appliances product and we think you will too. Among other things, registration of your appliance ensures that we can deliver important product information and warranty details when you need them.
The Good Ice™

OPAL 2.0 ICE MAKER
OWNER’S MANUAL
XPIO13BCBT
XPIO13SCSS
XPIO23BCBT
XPIO23SCSS