KLARSTEIN 10040189 Kraftwerk ECO Smart 11 Air Conditioner

Dear customer,
Congratulations on the purchase of your appliance. Please read the following instructions carefully and follow them to prevent potential damage. We accept no liability for damage caused by disregarding the instructions and improper use. Please scan the QR code to access the latest operating instructions and further information about the product.

TECHNICAL DATA

NOTES ON REFRIGERANT

CAUTION
Risk of fire! This device contains the flammable refrigerant R290. If the refrigerant escapes and is exposed to an external ignition source, there is a risk of fire.

Warnings

• The air conditioning system must be kept and transported upright. Otherwise, irreparable compressor damage may occur. Leave the unit for at least 24 hours before putting it into operation.
• Switch off the device and disconnect it from the power supply before cleaning.
• Make sure that the product creates a steady stream of air. Ensure the air inlets and outlets are not blocked.
• To prevent leaks, operate this unit on a horizontal surface.
• Any person performing work on a refrigerant circuit should have a current certificate from an industry-accredited assessment body. This ensures competence for the safe handling of refrigerants according to an industry-recognized assessment specification.
• If the device stops working, dispose of it properly.
• Store the device in a well-ventilated place when not in use.
• Store the device so that it is not damaged.
• Repairs may only be carried out by the manufacturer or an authorized specialist company.
• Do not damage any components of the refrigerant circuit. Escaping refrigerant may not be noticed because it is odorless.
• Maintenance and repairs must be carried out under the supervision of specialists in the use of flammable refrigerants.

Information for rooms with refrigerant pipes

• Limit the piping to a minimum.
• Be careful not to damage the piping.
• Appliances with fl ammable refrigerants may only be installed in a well-ventilated room.
• Comply with national gas regulations.
• All mechanical connections must be freely accessible for maintenance purposes.

SAFETY INSTRUCTIONS

Special notes

• Only use agents recommended by the manufacturer for defrosting or cleaning.
• Never store the appliance in a room in which there are permanent sources of ignition (e.g. open flames, a switched-on gas appliance or a switched-on electric heater).
• Do not puncture or burn the appliance.
• Note that coolant may be odorless.

Note: Only use the unit in rooms larger than X m² (see table):

General safety instructions

• The device is only suitable for indoor use.
• Do not use the product if it needs to be repaired or if it has not been installed properly.
• Do not use the product in the following areas:
  • near heat sources,
  • in areas where oil can splash,
  • in areas exposed to direct sunlight,
  • in areas where splash water can occur,
  • near bathtubs, in washrooms, near showers or swimming pools.
• Never insert your fingers or other objects into the ventilation openings. In particular, warn children of the dangers this may cause.
• Ensure that the unit is held vertically during transport and storage so that the compressor is correctly positioned.
• Always turn off the appliance before cleaning and unplug it from the wall outlet.
• Switch off the appliance before moving it and unplug it from the wall outlet. Move the appliance slowly and carefully.
• To avoid the risk of fi re, do not cover the unit.
• All fan connections must comply with local electrical safety regulations. If necessary, refer to these regulations.
• Supervise children so that they do not play with the unit.
• If the power cord is damaged, it must be replaced by the manufacturer, customer service or a similarly qualifi ed person to avoid danger.
• This equipment may be used by children over the age of 8 and by persons (including children) with limited physical, sensory or mental capabilities and/or lack of experience and knowledge, provided they have been instructed in the use of this equipment by a person responsible for their safety and understand the hazards associated with the use of this equipment. Cleaning and maintenance of the appliance may only be carried out by children under supervision.
• The appliance must be installed in accordance with national wiring regulations.
• Type and voltage of fuses: T, 250 V AC, 2 A or higher.
• Contact customer service for cleaning and maintenance.
• Do not pull the power cord, deform or modify it, or immerse it in water. Incorrect handling of the power cord may result in damage to the equipment and/or electric shock.
• National gas regulations must be observed.
• Do not block the ventilation openings.
• Do not operate the appliance solely by inserting or removing the power plug, as this may result in electric shock or fi re due to heat.
• Immediately unplug the appliance from the wall outlet if it emits strange noises, odours or smoke.

Instructions for handling damage

• In case of damage to the device, contact the manufacturer, customer service or a similarly qualified person.
• If damage occurs, turn off the power, unplug the power cord, and contact the manufacturer, the service representative, or a similarly qualified person.
• The power cord must be securely earthed.
• If the power cord is damaged, turn off the power to avoid danger and unplug the power cord from the wall outlet. The power cord must be replaced by the manufacturer, customer service or a similarly qualified person.

WARNING
Risk of injury! Repairs to the coolant circuit may only be carried out by trained specialist personnel. Never attempt to repair the unit yourself!

DEVICE OVERVIEW

1. Control panel
2. Retainer for remote control
3. Air outlet
4. Air intake
5. Air outlet
6. Air intake
7. Water plug/water outlet
8. Air intake
9. Cable storage
10. Air intake
    Accessories
11. Adapter
12. Exhaust air hose
13. Adapter
14. Water drainage hose (for permanent water drainage)
15. Activated carbon filter
16. Remote control

INSTALLATION

Before you start up your air conditioner, you must install the exhaust hose so that the condensed heat from the unit can be discharged outside. To install the exhaust hose, pass the end of the hose through an existing window and secure it with the provided adapter. Make sure that the distance between the unit and the window is at least 50 cm.

Installing the exhaust air hose

• Only use the supplied hose and attach the exhaust hose to the back of the air conditioner.
• Avoid kinks and bends in the exhaust air hose, otherwise the expelled humid air will accumulate and the unit will overheat and shut down. The correct positioning is shown in the illustrations (right).
• The hose can be extended from 30 cm to 150 cm, but for maximum efficiency the shortest possible length should be used.
• Note: The length of the exhaust air hose is specifically adapted to the specifications of the appliance. Do not replace or extend this with any other hose from your household as this may cause the appliance to malfunction!

Installation of the activated carbon filter

• Remove the plastic filter from the appliance.
• Take the activated carbon filter out of the plastic bag.
• Put the activated carbon filter into the device. Put the plastic filter back into the unit.

CONTROL PANEL

1. On/Off button
2. Fan speed button
3. Timer indicator
4. Timer button
5. Sleep mode button
6. Sleep mode indicator
7. Mode button
8. Temperature [+] button
9. Temperature [-] button
10. Compressor mode indicator
11. “Water tank full” indicator
12. Low fan speed indicator
13. Medium fan speed indicator
14. High fan speed indicator
15. IR receiver for remote control
16. Display
17. Automatic mode indicator
18. Dehumidification mode indicator
19. Cooling mode indicator
20. Fan mode indicator
21. WiFi indicator
22. WiFi mode button

All functions can also be performed with the supplied remote control. The remote control requires a CR2032 battery for operation.

OPERATION

Switching the unit on/off
Press the On/Off button, the unit starts in automatic mode.
Automatic mode
In automatic mode, the unit can cool or ventilate depending on the ambient temperature and setpoint setting. The unit is preset as follows:

• The default setting in automatic mode: If the ambient temperature is above 25 °C, the unit is in automatic cooling mode and runs according to the set setpoint (default setting: 24 °C). During operation, the “automatic mode” and “cooling mode” indicators light up.
• In automatic cooling mode, the fan speed setting is ineffective, the unit selects the fan speed automatically.
• If the ambient temperature is less than or equal to ( < ) 25 °C, the unit runs in automatic fan mode. The “automatic mode” and “fan mode” indicators light up. In automatic fan mode, the fan speed can be set manually.
• The indicators of the current functions light up simultaneously. The display shows the room temperature from 0 °C to 50 °C.
• To switch off the device, press the On / Off button again.

Note: To prolong the life of the compressor, please wait at least 3 minutes after switching off the unit before switching it on again.

Setpoint adjustment in automatic cooling mode 18-32 °C
If you set the setpoint to 24 °C, the unit starts cooling at 27 °C (setpoint + 3 °C). It cools down to 25 °C (setpoint + 1 °C) and then switches back to fan mode (low fan speed).

Note: The cooling system switches off when the ambient temperature is lower than the set temperature. The fan continues to run at the set level. If the ambient temperature rises above the set value, cooling will start up again.

Setting the functions
Press the mode button to select the desired operating mode:

• Automatic mode
• Cooling mode
• Fan mode
• Dehumidification mode (dry).

The indicator of the selected mode lights up.

Setting the temperature

1. Press the [+] and [-] buttons to set the desired temperature.
2. The display shows the temperature you have set when you press the [+] and [-] button. Otherwise, it always shows the ambient temperature.
3. The preset temperature in cooling mode for this unit is 24 °C.
   Setting fan speed
4. Press the fan speed button to set the desired fan speed: high, medium or low. The indicators for high, medium or low fan speed light up simultaneously.
5. When the unit is in automatic mode, it automatically selects the fan speed according to the ambient temperature (the corresponding indicators light up). The fan speed key and the [+] and [-] keys are deactivated.

Setting the timer

1. Press the timer button to set the desired operating time (1 to 24 hours), the timer indicator lights up. When the set time is reached, the unit switches off automatically. When you press the timer button, the display shows the hour(s) you have set. If the timer button is not pressed, the unit runs continuously.
2. If you press the timer button without switching on the other functions, you can preset the time that the appliance is to be in operation. For example, if you set the timer to “2”, the appliance will automatically go into operation after 2 hours.

Sleep mode

1. If you press the sleep mode button in cooling mode, the set temperature is increased by 1 °C in the first hour, by another 1 °C in the second hour and then kept at this temperature.
2. In sleep mode, the fan runs at a low level. If you press the sleep mode button again, the temperature setting and the fan speed are reset to the originally set values.
3. The unit switches off automatically when the unit has been in sleep mode for 12 hours.

Note: Note that sleep mode is not available when the unit is running in automatic mode, fan mode or dehumidification mode. When the unit is operated in sleep mode, the fan shuts down to the lowest level.

Dehumidification mode (dry).
In dehumidification mode (dry), the temperature cannot be set, the fan runs at low speed. When the unit is running in dehumidification mode (dry), the moisture extracted from the air is collected in a tank inside. When the tank is full, the compressor and the engine switch off automatically. At the same time, the “water tank full” indicator lights up. An alarm sounds. When the tank is full, drain the water as described in the section “Draining the Water”. You can also use the appliance without having to empty the tank so often by using the “permanent water drainage”, see also the section “Draining the Water” for this.
TiO2 mode (photocatalyst)
A photocatalyst is a material that functions as a catalyst (changes the rate of a chemical reaction) when exposed to light. It is helpful in fighting bacteria, mould and bad odours. This function is designed to remain activated as long as the unit is switched on. It is set by default and cannot be controlled via the control panel, the remote control or the smartphone app. Self-diagnosis This unit is equipped with a self-diagnostic function that warns you of any faults or malfunctions it detects in the course of its normal operation. Each error that the unit detects during self-diagnosis is signalled by a display: E1, E2, E3 or E5 (according to the respective malfunction of the unit). Should a malfunction occur, please contact the manufacturer, customer service or a specialist company.
WiFi function
See the following section: “Device Control by Smartphone”.

DEVICE CONTROL BY SMARTPHONE

If you integrate the device into your home WiFi, you can conveniently operate it via the associated Klarstein app. The app not only allows you to remotely control the device via your smartphone, but also gives you access to recipes and additional information. Follow these steps to connect your smartphone to your Klarstein device:

1. Download the Klarstein app first by scanning the QR code with your smartphone (see below), or download it directly from App Store or Google Play.
2. Make sure your smartphone is connected to the same WiFi network that your Klarstein device is to be connected to.
3. Open the Klarstein app.
4. Sign in to your account. If you do not have an account, sign up in the Klarstein app.
5. Follow the instructions from the app.

App Download
Use the scan function of your smartphone to scan the QR code and save the app on your smartphone.

Note: The app provides further information on how to use the app and help on how to connect to your device as soon as you open it for the first time.

Troubleshooting connection problems
If your Klarstein device cannot be found in the WLAN, check the following:

1. The device is not plugged in. Make sure that your device is plugged into an electric socket.
2. The device is not in pairing mode. Make sure that the WiFi indicator (LED) on the smart device control panel is blinking as described in the ‘Reset WiFi settings‘ instruction of your smart device (instructions are usually available on device connection process).
3. The WiFi access point does not operate on 2.4 GHz. Make sure that your access point operates on 2.4 GHz band and you have a separate SSID on 2.4 GHz band. If you are not sure about the operating band of your access point, please contact your internet provider company.
4. Firewall settings of your WiFi network; the firewall setting of your WiFi network may not allow the Klarstein app to configure the WiFi settings on your smart device. Please make sure that you are not using a public WiFi network, e.g. airports, dormitories, companies, etc.
5. Different credentials used in smartphone and the app. Make sure that the WiFi credentials entered in the Klarstein app are the same as the ones that your smartphone is connected to.Following the above mentioned points, if your smart device still fails to connect to the app, please contact us via email for support: [email protected]

DRAINING THE WATER

During the cooling process, the unit extracts water from the humid air. When the water tank is full, both the compressor and the motor switch off and the appliance emits a buzzing sound. Press any key to stop the buzzing. The “water tank full” indicator flashes. To restart the cooling function, empty the water tank as follows:

1. Switch off the air conditioner and do not move it when the water tank is full.
2. Place a container (e.g. a water bowl) under the drain opening.
3. Remove the drain plug and the rubber plug from the drain opening and let the water drain off.
4. When the container is almost full, put the rubber plug back on the drain hole and empty the water tray.
5. Repeat the process until the unit is completely empty.
6. Replace the rubber plug and screw the drain cap tight.
7. Switch the device on. The full water tank or compressor indicator should now stop flashing.

Permanent water drainage
If you want to use the machine without emptying the water tank, proceed as follows:

1.  Remove the drain plug and rubber plug and store it well for later use.
2. Connect the supplied drain hose to the drain opening as shown and guide the other end into a drain.
3. The drain hose can be extended using an extension hose with a suitable connector.

Notes:

1. The drain must be at or below the level of the water outlet of the appliance.
2. The “water tank full” indicator does not flash when water is continuously draining.
3. If you want to extend the drain hose, you can connect it to another hose (outer diameter OD: 18 mm).

FIXING THE WINDOW SEAL

Fixing the sealing frame for sliding windows
The sliding window sealing frame is designed to fit most standard vertical and horizontal windows. However, you may need to change some aspects of the installation for certain types of windows. The sealing frame can be fixed with screws.

Adjusting the sealing frame for sliding windows

Slide frame (B) into frame (A) and adjust the size of the frame to the width of your window. Lock the locking screw (C) in the holes corresponding to the measured width to ensure that there are no gaps or air pockets between the window and sealing frame after installation.

Fixing the seal for side-opening windows and roof windows
The installation of the window seal is simple. You can attach the seal to a tilted window, a side-opened window or a roof window. We have chosen a side-opened window for demonstration purposes. It is particularly suitable because the exhaust hose can be attached to the side far down. The Velcro tape is attached to the three open sides. The side where the window is against the frame is left out. Clean and dry the window frame beforehand so that the tape adheres.

CLEANING AND MAINTENANCE

• Always disconnect the air conditioner from the power supply before cleaning.
• To increase the efficiency of the air conditioner, it should be cleaned regularly.

Cleaning the housing

• Use a soft, damp cloth to wipe the housing.
• Never use aggressive chemicals, petrol, cleaning agents, chemically treated cloths or other cleaning solutions. These can damage the housing.

Cleaning the filter
Use a hoover or tap the filter lightly to remove loose dust and dirt from the filter, then rinse it thoroughly under running water (not hotter than 40 °C). Allow the filter to dry thoroughly before reinserting it.

Note: Never operate the unit without the filter.

Storage at the end of the season

• Empty the water tank before running the unit in fan-only mode for a few hours to thoroughly dry the inside of the unit.
• Clean or change the filter.
• Unplug the power cord and stow it away.
• Place the unit in the original box or lid for storage.

TROUBLESHOOTING

Note: Never attempt to repair or disassemble the unit yourself.

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your  localauthority or your household waste disposal service. This product contains batteries. If there is a legal regulation for the disposal of batteries in your country, the batteries must not be disposed of with household waste. Find out about local regulations for disposing of batteries. By disposing of them in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences.

DECLARATION OF CONFORMITY

Manufacturer:
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.
Importer for Great Britain:
Chal-Tec UK limited Unit 6 Riverside Business Centre Brighton Road Shoreham-by-Sea BN43 6RE
United Kingdom
The complete declaration of conformity of the manufacturer can be found at the following link: use.berlin/10040189

KLARSTEIN 10028295 Spin Doctor Ceiling Fan

Dear Customer,
Congratulations on purchasing this device. Please read the following instructions carefully and follow them to prevent possible damages. We assume no liability for damage caused by disregard of the instructions and improper use. Scan the QR code to get access to the latest user manual and more product information.

TECHNICAL DATA

SAFETY INSTRUCTIONS

• Never attach the fan to a power point,but to the ceiling itself.
• The minimum distance between the blades of the fan and the floor must be more than 2.3 m.The minimum carrying capacity of the hook from which the fan is hung must be 100 kg.
• Make sure to install all poles disconnection switch having a contact separation of at least 3 mm between poles in the supply wiring to the ceiling fan.
• The model or type reference of luminaries which may be installed in fans which are constructed for his purpose.
• Switch off the power before connecting.
• The electrical wiring must be in accordance with the local regulation.
• The fan must be properly earthed to avoid the risk of electric shocks.
• Never mount the fan in a moist or wet room.
• Be careful when working near the rotating blades.

INSTALLATION

1. Locate and mark the canter of the joist. Pass the supply wires throught the hole in the bracket.
   Secure the bracket to the ceiling joist by using the flat washers, sping washers and wood screws.
   
2. Hang the fan onto the bracket hook by using one of the holes at the top of the upper canopy screws.
   
3. Connect wires from supply and the wiring terminals as the photo.
   Brown wire: “L”
   Blue wire: “N”
   Green/Yellow wire:
   
4. Lift fan until the screws reach the bottom of the slots and then rotate the canopy counterclockwise until the screws drop into the slot redesses.
   
5. Insert the other two set screws and washers.
   Tighten all the screws, make sure that the canopy is secure and that you have not trapped any wires.
   
6. Install the fan blades onto the motor by tightning the hexafonal screws and spring washers.
   
7. Unscrew the regulator cover, Connect wires through the inlet hole according to the diagrams. Mount the regulator on wall on a wooden base block.
   

USE AND OPERATION

• Turn electricity on before the fan start to work.
• The fan starts to operate when pulling the Three-speed Switch connected by an extension chain on the motor housing.

The fan can be in different speeds as pulling the Three-speed Switch:

• The first pulling = HIGH SPEED
• The second pulling = MEDIUM SPEED
• The third pulling = LOW SPEED
• The fourth pulling = OFF

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

MANUFACTURER & IMPORTER (UK)

Manufacturer:
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.

Importer for Great Britain:
Chal-Tec UK limited
Unit 6 Riverside Business Centre
Brighton Road
Shoreham-by-Sea
BN43 6RE
United Kingdom

www.klarstein.com

Klarstein 900-1000W Coffee Machine

TECHNICAL DATA

SAFETY INSTRUCTIONS

• Read this manual carefully to avoid any risk of physical damage, fi re, electric shock, personal injury or property damage.
• This machine is intended for making coffee by means of a pressure fi lter („espresso“) and for domestic use indoors.
• Do not use the machine for any purpose other than its intended use.
• Children from the age of 8 years and persons with mental, sensory and physical disabilities may only use the appliance if they have been thoroughly familiarised with the functions and safety precautions by a responsible supervisor and understand the risks involved.
• Repairs may only be carried out by qualifi ed personnel and are necessary if the appliance has been damaged, the power cable or plug has been damaged, liquids have spilled on it or objects have fallen on it, if the appliance has been exposed to moisture or dampness or has been dropped or does not work properly.
• Please use only the accessories recommended by the manufacturer of this unit to ensure the operation of the unit.
• Before using the appliance, ensure that the water tank of the appliance is always fi lled with the amount of water required for the intended application to prevent damage to the appliance.
• Keep away from hot steam escaping from the appliance. Only use the handles or levers attached to the appliance or its components when moving hot components of the appliance, such as the frother or fi lter.
• To avoid electrical damage to the unit, do not immerse the unit in water for cleaning.
• Do not touch the plug of the unit with wet or damp hands. The moisture from your hands may drip onto the plug and cause a dangerous electric shock when it comes into contact with the power outlet.
• Supervise the unit during operation.
• Keep the unit and its components dry, clean and out of the reach of unauthorised persons.
• Supervise children while they are playing near the machine to protect them from damage.
• Unplug the machine from the power outlet when not in use.

PRODUCT OVERVIEW

• Remove the appliance from the packaging and check that all parts are complete and undamaged.
•  Clean all removable parts and dry them carefully.

COMMISSIONING

1.  Place the unit on a stable and level surface near a power outlet.
2.  Install the drip tray and place the cup holder tray on it.
3.  Remove the water tank, fill it with water and replace it.
   Note: The water must be filled in between the MIN and MAX marks.
4.  Place a cup or mug on the cup holder tray. Make sure that the steam switch and the coffee switch are in the off position.
5.  Insert the coffee sieve in the sieve holder, but do not yet fill in any coffee. Make sure that the coffee sieve is properly engaged.
6.  Place the cup or mug under the coffee outlet nozzles.
7.  Connect the machine‘s power cord to a power source.
8.  Set the On/Off switch to the ON position and scrape the machine The power indicator starts flashing red and the machine starts to heat up. When the heating phase is complete, the red light is steady on.
9.  Press the coffee switch upwards and the machine starts dispensing hot water. Slide the coffee switch down to stop the water output.
10.  When no more water is dispensed, remove the water tank, rinse it and clean the cup or mug used. The coffee machine is now ready for use.

OPERATION

Filling the coffee sieve with coffee

1.  Insert the coffee sieve into the sieve holder.
2.  Fill the coffee sieve with freshly ground coffee.
3.  Make sure that the coffee does not exceed the edge of the filter.
4.  Press down the coffee with the measuring spoon and coffee press, add coffee if necessary and press down again
5.  Remove excess coffee from the edge of the filter to ensure easy installation of the filter holder in the machine and good operation.

Note: Pressing down the coffee is a very important part of coffee preparation.

Installation of the sieve holder

1.  Turn the sieve holder to the left to remove it
2.  Select the desired sieve for 1 coffee or 2 coffees The 2 coffee sieve requires a larger quantity of coffee.
3.  Follow the steps in the section above to fill the sieve with coffee. Use freshly ground coffee for best results.
4.  Put the sieve holder back into the machine by turning it to the right until it fits into the locking position.

Brewing coffee

1.  Fill the appropriate coffee sieve with coffee.
2.  Attach the sieve holder
3.  Switch on the machine by setting the power switch to ON. The red indicator light starts to blink and the unit starts to heat up.
4.  As soon as the heating phase is complete, the red light is constantly lit.
5.  Press the coffee switch downwards and the machine starts to brew coffee. To stop dispensing coffee, move the switch to the off position.

Frothing milk
When the coffee is brewed, you can start frothing the milk.

1.  Press the steam switch downwards, the blue light indicator starts to flash.
2.  As soon as the machine has heated up, the blue indicator light stops flashing.
3.  Fill a cup or mug with milk. We recommend using whole milk at room temperature for better results.
4.  Insert the steam pipe into the cup or container at a depth of 1-2 cm. When frothing milk, move the cup or container up and down. Slowly turn the steam regulator counter-clockwise to allow steam to escape. The steam pipe can release a few water droplets before steam is generated.
5.  Once the required amount of milk foam has been produced, turn the steam control knob clockwise and set the steam switch to the off position.

Boiling water

1.  Turn on the machine by setting the power switch to ON. The red indicator light starts to blink and the unit starts to heat up.
2.  As soon as the heating phase is complete, the red light is constantly lit.
3.  Press the coffee switch downwards and the machine starts dispensing water. To stop the water output, move the switch to the off position.
4.  Wait until the machine has heated up again and repeat these steps to dispense hot water.

After use
After steam/water dispensing or coffee brewing, the temperature of all machine components rises because the machine has been working under high pressure. If the machine overheats, the two light indicators will start to fl ash rapidly, indicating that the temperature of the machine needs to be lowered.

• Turn the steam control knob anti-clockwise and press the coffee switch to the on position. Water is released through the steam pipe.
• When the red light stops flashing, set the coffee switch to the off position and turn the steam control knob clockwise.
• The machine is now ready to brew coffee again.

CLEANING AND CARE

To ensure a pure taste, carry out cleaning after each use. Descaling and maintenance should be carried out every 2-3 months.
Cleaning the coffee sieve and sieve holder

• Remove the sieve holder and remove the coffee sieve. Tap the sieve holder lightly against the sieve to remove the coffee grounds.
• Then clean the sieve holder and the coffee sieve with clean water and dry them before putting them back together.

Water outlet, steam pipe and steam attachment
After milk frothing, turn the steam control knob completely open so that the steam outlet releases steam for a few seconds and cleans the steam pipe and steam attachment. Allow the steam pipe and steam attachment to cool down after milk frothing. Then clean the steam tube and steam attachment immediately with a damp cloth. This prevents milk residues from accumulating.

Removable parts and housing
Clean the water tank, the surface of the appliance, the drip tray and the drip tray cover with a damp cloth.

Descaling
Descale the machine every two months using a standard descaler or a vinegar-water solution in a ratio of 1:4. Fill the water tank with the mixture and run the mixture through the machine once. Then fill the tank with fresh, clean water up to the MAX mark and let the water run through again.

FREQUENTLY ASKED QUESTIONS

Which powder is right for the espresso machine?
The right powder can be identified by the shape of the powder after it has been compressed in the sieve:

• If the powder is mushy, it is too fine.
• If the powder crumbles, it is too coarse.
• If the powder holds firmly together, it is suitable.

What is the right amount of powder?

• If you are preparing 1 espresso, put a spoon (about 8 g) of espresso powder in the small sieve.
• If you are preparing 2 espressos, put two spoons (about 16 g) of espresso powder in the large sieve.

What is the function of the small hook on the screen holder?
The hook prevents the sieve from falling out of the sieve holder when the powder is emptied.

What is the function of the steam cap on the steam tube?
It ensures that the milk is swirled by the steam. This makes the milk foam firmer and finer.

Why can‘t the milk be frothed?

• Make sure that the milk used is cold.
• Do not froth the milk for too long. If it gets too hot, no milk foam can form.

What can you do if the bubbles in the milk foam are unevenly large?
Knock on the milk cup to remove large bubbles. Then shake the milk cup horizontally to completely mix the milk and milk foam.

Which milk is suitable for frothing?
Low-fat milk is easy to foam, but the bubbles and foam are slightly larger and looser. Whole milk is more difficult to foam, but the milk foam becomes thick and tough.

What to do if no steam comes out of the steam attachment?

• This is usually because the steam pipe and the steam cap have not been cleaned after milk frothing and milk residues block the steam pipe.
• Try cleaning the pipe with a small cleaning brush.
• If this does not help, add vinegar and water to the water tank at a ratio of 1:1. Then start the steam function to clean the hose. Then top up with fresh water and restart the steam function.
• If the problem persists, contact your service representative.

TROUBLESHOOTING

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

MANUFACTURER & IMPORTER (UK)

• Manufacturer:
• Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.
• Importer for Great Britain:
• Chal-Tec UK limited
• Unit 6 Riverside Business Centre
• Brighton Road
• Shoreham-by-Sea
• BN43 6RE
• United Kingdom

SKAL
Beer Dispenser
10030663
10032176
COOKINGCOwww.klarstein.com

Dear Customer,
Congratulations on purchasing this equipment. Please read  this manual carefully and take care of the following hints to avoid damages. Any failure caused by ignoring the items and cautions mentioned in the instruction manual is not covered by our warranty and any liability. Scan the QR code to get access to the latest user manual and other  information about the product:

https://use.berlin/10030663

TECHNICAL DATA

Note: This is a household beer cooler, equipped with a CO₂ cartridge pressure system to keep the beer fresh. It brings the beer to the best temperature for cold storage (0 to 4℃) within 19-21 hours. The beer cooler will keep the 5 L Keg cool for an almost indefinite period. We do, however, suggest that you initially cool your beer keg for at least 12 hours in your refrigerator before placing it into the beer cooler.

SAFETY INSTRUCTIONS

• Read all safety and operating instructions before using the device. Keep the operating instructions in a safe place for future reference.
• Check that the power cord is intact before use. If this is not the case, contact customer service.
• If the power cord is damaged, it must be replaced by Customer Service to avert danger.
• Before use, check that the plug fits the outlet. If this is not the case, contact Customer Service.
• Do not handle the power plug with wet hands when plugging in or unplugging it.
• Place the appliance on a dry and level surface.
• To ensure adequate ventilation around the unit, leave at least 12 cm of free space around the unit.
• Place the unit in direct sunlight.
• Do not cover the device with objects when it is in operation.
• The device must be installed in an area that is protected from environmental influences such as wind, rain and water splashes.
• Disconnect the device from the power supply before cleaning it. Failure to do so may result in electric shock or death.
• Do not immerse the product in water or any other liquid.
• Do not use coarse cloths or abrasive cleaners to clean the product.
• Do not take the keg out of the dispenser if the beer has not been fully drawn.
• Do not remove the CO₂ cartridge until it is empty.
• Do not use CO₂ cartridges if the room temperature exceeds 49°C. Failure to follow this warning may result in explosion and death.
• Do not allow children to operate, play with or crawl into the system.
• Children must be supervised so that they do not play with the equipment.
• Do not store explosive materials such as spray cans of flammable propellants in this appliance.
• This appliance is intended for use in the home and similar establishments, such as kitchenettes in shops, offices and other working environments in manor houses, hotels, motels and other non-business catering facilities.

PRODUCT OVERVIEW

1 Top cover 2 CO₂ cartridge sheath 3 Tap handle 4 Tap 5 Keg lifter 6 Drain switch 7 Drip tray 8 CO₂ pressure relief valve/ knob 9 LED display Drain switch/ Digital control button Drip tray 10 Door lock button 11 Rear cover 12 Power cord & plug 13 AC power switch

COMMISSIONING

Installation

1. Take out the beer cooler from its package. Place the beer cooler on a steady and horizontal surface, and make sure the beer cooler is at least 5 inches/10 cm away from other appliances or wall on each side so as to allow correct ventilation on the appliances to get better performance.
   
2.  Install the tap handle connect the tap, make sure both end fit together perfectly.
3. Set the water drip tray into the notch provided.
4. Plug the beer cooler.
   Note: Do not connect or disconnect the electric plug when your hands are wet. Before use it, make sure the voltage is in conformity with plug mark, and check whether the power cord is well connected or not; if not, please don’t use it, and call service center.
5. Put 800ml water into the cooling cavity or pour the water to the max mark (It can work without water, but it can’t display the best performance).
   Note: Make sure the drain switch is at “Off” position, and no extra objects in the cooling cavity

HOW TO SELECT A KEG

• Sealed 5L universal keg and Heineken keg applies only
• Pay close attention to safety and storage messages about the keg / on the keg.
• Check the keg is neither damaged nor beer out-of-date before purchasing.
• Protect the top surface from being damaged. Otherwise it could be difficult of accession for the suction tube.
• Keep the keg in a rather cold for 12 hours but not too cold place (e.g. refrigerator) until next use.
• Never shake the keg before use
• Never put the beer keg under the sunlight

Beer keg sealant
All 5 Liter beer keg with the below various appearance sealants can apply to the beer cooler, however, you should follow the information as below.
The sealants with code No. 20 and 21 can be pierced simply by the cooler piercing pin.

The sealants with code No. 22 need to be removed off the marking ring from the sealant and pierce the keg by cooler piercing pin.

The difference between code No 23 and 24 is the safety clasp quantity. Pull up the safety clasp carefully, turn around and take it out from the keg; replaced it by the sealant (like code No 20 sealant) provided in the beer cooler, attach it to the beer keg, and pierce it by cooler piercing pin.

Note: Important: Before replacing the sealants or piercing the cooler kit, you must always follow the instructions marked on the keg to eliminate the excess gas and ensure that the keg has rested long enough to avoid foam coming out through the cooler piercing pin /tap faucet. And it is no need to release the gas and replace the seal rubber if you use Heineken keg, because Heineken keg has its own CO₂ pressure inside, and no need to be provided from outer CO₂ pressure system. 

Universal 5 L beer keg

1. Before piercing the plug on the top of the keg, you must always follow the instructions marked on the keg to eliminate the excess gas and ensure that the keg has rested long enough to avoid foam coming out through the tap faucet.
2. Uprightly direct the piercing pin against the sealant on the upper center of the keg (maybe you need to tear off the marking ring or change a proper sealant), press the piercing pin/keg lifter to poke the sealant and then push the piercing pin all immerse in the keg quickly. To assemble the tap mechanism until you hear a “Ka” sound that will indicate the tap mechanism fixes on the beer keg.
   
3. Open the beer cooler with 30-40 N strength and place the well-assembled keg into the cooling cavity; Connect the CO₂ connector tube and beer outlet tube with the keg lifter tube connector. Note: make sure all connection of tap mechanism is well connected, and without damage. And make sure tap valve is on close status, and the CO₂ pressure regulator knob is at “Off” status.
   
4. Loosen the CO₂ bottle sheath (Show as figure 15), insert a 16 gram CO₂ cartridge in the sheath (Figure 16), and screw the sheath tightly until you will hear a “Click”(Figure 17), which indicates that the cartridge seal has been pierced and the CO₂ gas can flow into the keg freely. Make us the bottle sheath is fixed tightly to avoid the CO₂ leakage. Then put CO₂ bottle sheath into the top cover.
   Note: Turn off the CO₂ knob when cooling the beer, turn off when the beer flow is paused, turn off when changing the CO₂ cartridge. If the beer cannot be tapped out (there is still beer in the keg), or beer foams are not enough, turn the knob to „+“ position for 5 seconds then turn it off again.
5. Close the top cover of the beer cooler; When pouring out the beer, the turn the knob on the top cover to “+” position to release the CO₂, and turn it to “-“position when pause or stop pouring beer to close the CO₂. Please refer to the notice label on the top cover.
6. Turn on the power switch to “I” position to power on the beer cooler. (While “0”position is to power it off). Note: Please make sure your hands are dry  when you operate the beer cooler, to avoid electric shock.
7.  It will take 19-21 hours to cool the beer to 0-4 °C at 22-24 °C ambient temperature. And it can keep the temperature as set and displayed on the LED.
   (The LED will display the real temperature of the beer). We do, however, suggest that you initially cool your beer keg for at least 12 hours in your refrigerator before placing it into the beer cooler, especially when the ambient temperature is higher than 25 °C.
8. The beer cooler has 6 preset temperatures. Press and hold the „-“ key to reach the cooling temperature setting. Press the „-“ key to set a fixed value of 12 °C, 10 °C , 8 °C, 4 °C or 2 °C. The cooling temperature is set by pressing the „-“ key. You can also press and hold the „+“ button to enter the temperature setting. Then press „+“ to set a fixed value of 2 °C, 4 °C, 6 °C, 8 °C, 10 °C, or 12 °C.
   

   The unit has a memory function that uses the last selected temperature value when you turn on the cooler. By default, the display shows the current temperature of the  beer. Press and hold the „+“ key to display the set temperature. The set temperature is displayed for 3 seconds, then the current temperature is displayed again.

   9. Adjust the CO₂ pressure regulator knob to “+” position, to pour the beer out by pulling down the tap mechanism, and you can adjust the pressure regulator knob to control the beer flow rate and beer bubble. Note: Clean the glass before pouring beer out; if the beer or beer cup/glass is in high temperature or the beer is not cool enough, there are many bubbles when pouring beer out.
   10. When taping the beer, lean your beer glass against the pouring spout and slowly straighten it up with the beer rising, then open the tap mechanism completely to avoid much bubble; It is advisable to pour half-glass, make a short pause before continuing the rest. Notes: Never immerse the pouring spout into the beer glass to avoid much bubble; Remember to lock the tap after finishing pouring.
   11. It is normal to have more bubbles when pouring the first 3 cup of beer.
   12. There will be a sharp and high-speed jet when pouring the last cup of beer from keg.

Heineken Keg
Heineken kegs are pre-charged with CO₂, and do not require the use of regulator, no need to install the CO₂ cartridge. And the knob on the top cover does not work.

The Heineken connector that comes with your beer cooler can work with all Heineken 5 L kegs. However you must use a flat head screwdriver to remove the green base from
the keg in order to install the new connector, provided with the beer cooler.
When install the new connector to the Heineken keg, you must firstly install the clear beer tube one end to the connector, one end to the tap mechanism, then install the connector to the Heineken keg.

Close the lid. Perform steps 6-12 as for the universal drum. Step 9 is different.

INSERTING A NEW BEER KEG

When the beer in the keg runs out, before changing a new beer keg:

1. Adjust the CO₂ pressure regulation knob to “-“ switch to shut off the CO₂ supplying and save the CO₂.
2.  Open the top cover of the beer cooler, pull down the tap handle to release the rest gas in the keg (maybe with some beer bubble).
3. Then put the piercing pin into the new keg and put into the beer cooler. Connect the gas-tube and beer tube from the keg lifter, by pressing the white parts of keg lifter.
4. Disconnect the gas-tube and beer tube from the keg lifter,
5. Take out the keg by the keg lifter, and pull out the piercing pin from the keg.
6. It is recommended to clean the tap mechanism when changing the beer keg each time. Please refer to the below contents about cleaning.

INSERTING A NEW CO2 CARTRIDGE

Note: not required for Heineken kegs!
Please change the CO₂ cartridge if can’t pour beer out when the CO₂ pressure knob is at “on” position and has beer in keg.

1. When turn the CO₂ pressure knob to “-“ position, to close the CO₂ supplying.
2. Open the top cover, loose the cartridge sheath, and take out the empty CO₂ cartridge. Insert a new 16g CO₂ cartridge in the sheath, and screw the sheath tightly until you will hear a “Click”, which indicates that the cartridge seal has been pierced and the CO₂ gas can flow into the keg freely. Make us the bottle sheath is fixed tightly to avoid the CO₂ leakage. Then put CO₂ bottle sheath into the top cover.
3. Close the top cover of beer cooler.
4. Turn the CO₂ pressure knob to “+“ position to turn on the CO₂ supply, and it is ready to pour beer out.

Note: Each 16 g CO₂ cartridge can pressure more than 5 L beer out.
Safety instructions:

• Please use the qualified CO₂ cartridge. The below CO₂ cartridge information for your reference. Never use Nitrogen gas cartridge in the beer cooler to avoid the explosion, because of its much higher pressure;
• New CO₂ cartridge need good reserve, any play if forbidden, or will cause hazards.

Net weight	15,5-16,5 g	B	88-89 mm
Volume	20 ml	C	21,7-22 mm
Gross weight	57-58,6 g	D	19-11 mm
Cartridge weight	42-42,6 g	Pressure	60 kgf/cm2
A	8,6-8,9 mm	Detonation pressure	45 bar

1. Open the drain switch to drain out the water from the cavity into the drip tray. Make sure the drip tray is fit into the notch to avoid water flow to the desk; the drip tray can load 450 ml water;
2.  After all water drain out, close the drain switch and put 800 ml fresh water into the cavity.
3. Open the drain switch (drag the switch forward to 90 degree angle), and drain out the water inside the cavity to drip tray, and need twice to drain out the water.

Note: clean water is necessary; make sure the drip tray is fit into the notch to avoid water flow to the desk; the drip tray can load 450 ml water.

CLEANING THE BEER TAP MECHANISM

The beer dispenser must meet hygienic requirements. It must be cleaned before first use and after a long period of non-use. Clean the whole machine with a dry cloth. In addition, there are 2 recommended cleaning instructions:

1. Fill the cleaning set with warm water.
2.  Connect the end of the piercing needle. Press the water into the piercing needle to clean the inlet pipe. Press the water out of the beer hose at the other end. Repeat until the beer hose is clean. You need at least 3 bottles of warm water). Clean the dosing mechanism as shown in the picture below. Disassemble the tap when cleaning.

Dosing mechanism

• When cleaning the beer hose, open the tap.
• This connection must be connected to the cleaning cartridge.

Cleaning cartridge

Note: Never place the dosing mechanism in the washing machine or dishwasher. Never use chemical detergents to clean the parts. Use as warm, clean water as possible.

To change spare parts

Items	Name	Picture	Qty.	Instalment
1	Connector seal		3	Regulator valve
2	Piercing pin		1	Regulator valve
3	Beer tube		1	Beer-out connector
4	Tube seal circle		3	Beer-in pipe
5	Keg seal		2	Standard keg
6	Adaptor		3	Keg with integrated pressure cartridge
7	CO₂ cartridge		3	Regulator valve assembly
8	Air bulb		1

Firstly, pick out the seal washer with a tiny metal stick (Show as fi gure), and take out Cartridge pierced probe. Be careful not damage other parts of regulator.
Cartridge pierced probe and seal washer
Cartridge pierced probe and seal washer maybe damaged when wrong usage or other  reasons, please replace a new one.

1. Install a new cartridge pierced probe in the regulator (leave the sharp end outside toward), and install the seal washer (Show as fi gure). Don’t remove other parts of regulator in the replacing process.

WARNING
Risk of injury! Remember to press the seal circle with empty cartridge instead of new cartridge, or will cause hazard.
To change beer tube
Please replace the beer tube if beer tube is damaged and cause beer leakage (see fi gure 26).

1. Loosen the tube at connection 1 and draw out the tube. Pull down the lock setting, and draw the tube out.
2. Screw out nut at connection 2, and draw the tube out.
3. Replace a new beer tube, and install the beer tube according to with the reverse procedure.

Note: Don’t move other screws when processing tube replacement, otherwise it may cause the beer leakage or gas leakage.

Replace the seal circle of beer tube
Replace the new seal circle of beer tube if the connector has leakage (see figure).

1. Replace the new seal circle of beer tube if the connector has leakage
2. Take out the seal circle of beer tube
3. Replace a new seal circle on same position
4. Turn the seal circle tightly to avoid any leakage

TROUBLESHOOTING

Note: If the beer cooler does not work properly, please call the service centre. To save time and money, before you call for service, check the Troubleshooting Guide. It lists cause of minor operation problems that you can correct yourself.

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must
not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

MANUFACTURER & IMPORTER (UK)

Manufacturer:
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.
Importer for Great Britain:
Chal-Tec UK limited
Unit 6 Riverside Business Centre
Brighton Road
Shoreham-by-Sea
BN43 6RE
United Kingdom