Orbit WT24 B-Hyve Smart WiFi Indoor Sprinkler Timer User Guide
Contents in the Box
- Wi-Fi Indoor Sprinkler Timer
- Screwdriver
- Mounting Screws and Anchors
- Transformer
- Quick Start Guide
- Conduit Cover
FCC and IC Statement
This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Warning: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help This device meets the FCC and IC requirements for RF exposure in public or controlled environments. The end-user is advised to maintain a distance of 20 cm from the controller and any personnel to ensure compliance with RF exposure regulations.
This Class B digital apparatus complies with Canadian ICES-003
The B-have App
Install the B-have app on your smart device
You will need a smart device to connect the timer to Wi-Fi.
Note: The app will guide you through the initial setup of your sprinkler timer. In addition, there are help icons throughout the app with more information and useful tips.
Timer Installation
Select a location
Choose a location near power and away from direct sunlight, if possible.
This location should also have a good Wi-Fi signal. You can check this using a smartphone. (Find a location that has a minimum of two bars)
Note: If replacing a timer, it is helpful to take a photo of the wires before you remove them from the old-timer.
Mount the timer
Install a screw (included) into the wall.
Use the expanding anchors (included) for plaster, masonry, or drywall installations. Hang the timer on the installed screw using the keyhole slot.
Level the timer and use the second screw in one of the preformed mounting holes to secure the timer.
Connect Valve Wires
Prepare wire
Strip 1/2″ (13 mm) of insulation from each wire.
Connect wires
Attach one wire from each valve to a “Common” (COM) wire and the other wires to a numbered terminal (only one wire per terminal.)
Timer Installation–Connecting to Wi-Fi
- Plugin your Orbit® B-have timer
Once your B-have timer is plugged into the power source, it will automatically look to pair with your smart device. They will begin to blink blue. This indicates that your timer is ready to pair with your smart device. Ensure that your smart device has Bluetooth® turned on. - Connect to your Orbit® B-have timer
Open your B-have app, create an account or log in, and follow the step-by-step process to add and set up your device. The B-have app will connect to your device and you will, then, be guided to connect to your home Wi-Fi network. - Connect to your Wi-Fi network
Select your network from the list and enter the password for the network to connect your timer to your Wi-Fi signal. When connected, the will illuminate solid white indicating a successful pairing.
Note: If you do not see your network name in the list, tap the refresh button in the app. If your network name still does not appear, tap “Advanced” in the app and enter your network name and password. This device will only connect through 2.4 GHz Wi-Fi networks. 5.0 GHz networks are not supported and will not appear in your app.
FOR OPTIMUM TIMER PERFORMANCE, CONNECT TO WIFI TO RECEIVE THE LATEST TIMER UPDATES.
Programming and Operation
- Programming the timer
The app has help screens and videos to assist you with Wi-Fi connections, programming, smart watering, and other general questions you may have. - Note: Your programmed schedules are stored both in the app and on the timer. Watering will continue if the Wi-Fi connection is lost.
- Manual Operation
All programming and full functionality of the timer is available in the B-have app. If you have the need, there are some basic operations you can perform directly at your timer.
| Function | Button Press |
| MANUAL WATERING | Hold 0 until R (water ALL stations) appears, then release. Quickly press 0 again until the desired station appears. Default watering is 10 min. per station. |
| CANCEL STATION | Press 0 once to cancel the current station. |
| RAIN DELAY | Set in-app; 0 blinks yellow and d appears. |
| ON/OFF | Hold 0 for 10 sec. until 0 turns white. |
| HARD RESET | Quickly press 05 times. |
Specifications
Transformer ratings:
Input:
Argentina: 230V AC 50Hz 23W
Australia: 240V AC 50/60Hz 23W
Chile: 220V AC 50Hz 23W
Europe: 230V AC 50/60Hz 23W
Peru: 220V AC 50/60Hz 23W
USA:
120V AC 60Hz 23W
Output: 24V 750 mA
Timer ratings:
Input/Output:
Argentina, Australia, Chile, Europe, Peru:
26V AC 750 mA 50/60 Cycle
USA: 24V AC 750 mA 60Hz
Timer Temperature Operating Range:
Operating: 32-158° F (0–70° C)
Storage & transport: -4–176° F (-20–80° C)
Timer Humidity Operating Range:
Operating: 0–80%
Storage & transport: 0–90%
Altitude:
6,500′ (2,000 meters)
RF Specifications:
Technologies: Bluetooth® / WiFi
Frequencies: 2402 – 2480 MHz
EIRP: BT (8.9mW), WiFi (114.29mW)
Installation Class II
Over Voltage Category II
This timer works with any standard 24V irrigation solenoid.
The internal fuse is non-replaceable.
Help
Europe & South Africa
Email:
South America
Phone: +56 2 22419718
Email: | bhyve.orbitonline.com
For proper treatment, recovery, and recycling, local codes require that you take this product(s) to designated collection points where it will be recycled free of charge.
Acts as a hub for other B-have products Orbit ® Irrigation Products, Inc.
845 North Overland Road
North Salt Lake, UT 84054 USA
FAQS
Does the Orbit WT24 B-Hyve Smart WiFi Indoor Sprinkler Timer work with my sprinkler system?
Yes, the Orbit WT24 B-Hyve Smart WiFi Indoor Sprinkler Timer can be used with any sprinkler system.
Can I control my Orbit WT24 B-Hyve Smart WiFi Indoor Sprinkler Timer remotely?
Yes, you can control your Orbit WT24 B-Hyve Smart WiFi Indoor Sprinkler Timer from anywhere using your smartphone or tablet. You can also control it from your computer using a web browser.
How many sprinklers can I control with my Orbit WT24 B-Hyve Smart WiFi Indoor Sprinkler Timer?
The Orbit WT24 B-Hyve Smart WiFi Indoor Sprinkler Timer can control up to 24 sprinklers at once.
Dose it come with power supply cord?
It comes with a 24 volt AC power pack. One of those wall watt power supply. You run low voltage wires from that wall wart to the controller. I was replacing old controller and used the already existing transformer as the 24 VAC is standard for these.
What if wifi takes a crap? And happens when you’re on vacation? Or won’t shut off & you’re gone 6 hours? Is it like flying w/auto pilot but no yoke?
If wifi is down, nothing happens. If your on vacation you can make a custom schedule for that time
You have complete control of your system, water saturation levels, everything.. And can adjust or change anytime.
How many zones does my Orbit WT24 B-Hyve Smart WiFi Indoor Sprinkler Timer support?
The Orbit WT24 B-Hyve Smart WiFi Indoor Sprinkler Timer supports up to 8 zones.
Can I use my existing wires to connect my Orbit WT24 B-Hyve Smart WiFi Indoor Sprinkler Timer?
Yes, you can use your existing wires to connect your Orbit WT24 B-Hyve Smart WiFi Indoor Sprinkler Timer to your irrigation controller. All you have to do is connect the wires according to the instructions in this manual and then mount the unit on a wall or ceiling using the included mounting hardware.
Can you use 2 different Orbit wifi controllers on same app?
Yes
Does this replace a diaphragm valve, or a timer that a pump is hooked up to?
It controls the opening and closing of diaphragm valves, but it does not replace them. It does have a “pump” circuit, to switch your pump on and off at running times.
Can I remotely turn on a valve manually from the smartphone app? That is why I want to buy a wifi controller.
Yes you can, you can manually control individual valves from the app.
Can a master valve be wired? If so, where does it plug in? Can I plug it at the “pump” terminal?
Yes, you can wire a master valve into the “Pump” terminal.
Can this controller use to control one 24v solenoid for a 4 zone index valve? did anyone tried and succeed ? capable of 4 on/off times in 1 day?
Yes it can! Also…You can set as many on/off times you want in a 24 hour period.
Does this work with Smartthings?
No, it doesn’t work with smartthings.
Is it compatible with Google home mini?
Do not know what google mini is
Does this time have the ability to withstand heat and cold? It would be placed on my garage wall (inside).
The package insert says operating temperature range is 32-158°F (0-70°C), humidity 0-80% and altitude 6,500ft. I have no idea why the altitude would be a limiting factor unless there is a built-in barometric pressure sensor on the circuit board.
Can this replace an old time for four zone system?
It should providing the old system used low voltage (24vac) valves and used a 24vac contactor to start and stop the pump if your system has a pump. If your old system used a mechanical time clock and an indexing valve to switch zones you would need to replace the time clock with a low voltage contactor and program the new controller to switch the pump off and back on to make the indexing change zones. This controller has 5 low power relays internally that the controller uses to turn power on and off to the valves and pump control contactor.
how to change when watering occurs?
Not quite sure what the question is.
If you’re asking about changing settings once your lawn has been watered then all you have to do is open the app and make any changes moving forward.
Is it safe for outside ?
It’s not weather sealed, so no. And it requires the router password for your internet system which means it’s not safe inside OR outside.
why are the dimensions conflicting?
Yes
Can the B-hyve connect over a Verizon cellular mifi for monitoring and use at a remote location?
As long as you have a wifi internet connection between your phone and the controller you should be able to control the unit.
