Panasonic Baby Monitor Additional camera KX-HNC301, KX-HNC300 Manual

Panasonic Baby Monitor Additional camera

Accessory information

Supplied accessories

No.	Accessory item/Part number	Qty.
A	AC adaptor*1	1
B	Wall mounting adaptor*2	1

For U.S.A. users:

1. PNWYAC300W00 (for U.S.A. users only)
2. PNWYAC300W01 (for U.S.A. users only)

Other information

• Design and specifications are subject to change without notice.
• The illustrations in these instructions may vary slightly from the actual product.

Installation

Connections

1. Insert the AC adaptor plug firmly into the DC jack.
2. Connect the AC adaptor to the power outlet.

Note:

• Use only the supplied AC adaptor S006AKU0500100.
• The camera unit can be placed on a flat surface. Make sure to choose a stable location.
• The camera can also be mounted on the wall (page 10).

Note about power connections
AC adaptor connection

• The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.)
• The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected.

Registering a camera unit

You must register the camera unit to your monitor unit before it can be used.

1. Monitor unit:
   MMENUN a MbN: “Camera Management” a MOKN a MbN: “Add Camera” a MOKN
   1. An operation guide is displayed. Press MOKN to continue.
   2. Complete the following step within 90 seconds.
2. Camera unit:
   Press and hold M N for 3 seconds until the LED indicator starts blinking.

Note:
A message is displayed on the monitor unit to show if the registration was successful or not, and a beep sounds.

LED indicator

You can use the LED indicator to confirm the camera unit’s status.

LED indicator	Status
Off	No power
Green, lit	Normal operation
Green, blinking slowly	Registration mode
Green, blinking quickly	Device malfunction

Graphical symbols for use on equipment and their descriptions

About this system

• This system is not designed to provide complete protection from property loss.
  To the maximum extent permitted by applicable law, Panasonic will not be held responsible for any damage incurred as a result of property loss.
• This product should not be used as substitute for a medical or caregiver’s supervision. It is the caregiver’s responsibility to stay close enough to handle any eventuality.
• The system’s wireless features are subject to interference, therefore functionality in all situations cannot be guaranteed.
  Panasonic will not be held responsible for injury or damage to property that occurs in the event of wireless communication error or failure.
• If a power failure occurs or the power is disconnected, the temperature will not be accurate for up to an hour.

For your safety

To prevent severe injury and loss of life/property, read this section carefully before using the product to ensure proper and safe operation of your product.

Power connection

WARNING

• Completely insert the AC adaptor/power plug into the power outlet.
  Failure to do so may cause electric shock and/or excessive heat resulting in a fire.
• Regularly remove any dust, etc. from the AC adaptor/power plug by pulling it from the power outlet, then wiping with a dry cloth. Accumulated dust may cause an insulation defect from moisture, etc. resulting in a fire.
• Unplug the product from power outlets if it emits smoke, an abnormal smell, or makes an unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped emitting and contact us.
  For U.S.A. users
  http://shop.panasonic.com/support
  For Canada users
  www.panasonic.ca/english/support
  www.panasonic.ca/french/support
• Unplug from power outlets and never touch the inside of the product if its casing has been broken open. Danger of electric shock exists.
• Never touch the plug with wet hands. Danger of electric shock exists.

Installation

• To prevent the risk of fire or electrical shock, do not expose the product to rain or any type of moisture.
• Do not place or use this product near automatically controlled devices such as automatic doors and fire alarms. Radio waves emitted from this product may cause such devices to malfunction resulting in an accident.
• WARNING:
  Strangulation Hazard: Children have STRANGLED in cords.
  Keep this cord out of the reach of children (more than 1 m (3 feet) away).
• Do not allow the AC adaptor to be excessively pulled, bent or placed under heavy objects.
• Keep small parts, such as screws, out of the reach of children. There is a risk of swallowing. In the event they are swallowed, seek medical advice immediately.

Operating safeguards

• Unplug the product from power outlets before cleaning. Do not use liquid or aerosol cleaners.
• Do not disassemble the product.
• Never put metal objects inside the product. If metal objects enter the product, turn off the circuit breaker and contact an authorized service center.

Medical

• Consult the manufacturer of any personal medical devices, such as pacemakers or hearing aids, to determine if they are adequately shielded from external RF (radio frequency) energy. DECT features operate between 1.92 GHz and 1.93 GHz with a peak transmission power of 115 mW (max.).
• Do not use the product in health care facilities if any regulations posted in the area instruct you not to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy.

Installation and location

• Never install wiring during a lightning storm.
• The AC adaptor is used as the main disconnect device. Ensure that the AC outlet is installed near the product and is easily accessible.
• Mount the product on the stable location where the camera unit can be adequately supported when installing.
• Do not mount the product on soft material. It may fall down, break or cause injury.
• Do not mount the product on the following materials: gypsum board, ALC (autoclaved lightweight cellular concrete), concrete block, plywood less than 25 mm (1 inch) thick, etc.

Preventing accidents and injuries

Do not put your ear(s) near the speaker, as loud sounds emitted from the speaker may cause hearing impairment.

Important safety instructions

When using your product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Do not use this product near water for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool.
2. Use only the power cord indicated in this manual.

Other information

Routine care

• Wipe the outer surface of the product with a soft moist cloth.
• Do not use benzine, thinner, or any abrasive powder.

Camera image quality

• Camera images may have the following characteristics.
  • Colors in images may differ from the actual colors.
  • Faces or objects may appear dark when there is light behind the subject (i.e., backlighting).
  • Image quality may be reduced in dark locations.

When the subject is lit by sunlight or halogen lights, black areas of the image may appear purplish. This is not a malfunction.

Wall mounting

• Attach the wall mounting adaptor to the camera unit after making the connections (page 3).
• Only use the supplied screw that is attached to the camera base when attaching the wall mounting adaptor to the camera unit. Do not use user supplied screws. This may cause the camera unit to become loose from the wall mounting adaptor.
• Mount the camera unit on the stable location where the unit can be adequately supported when installing.
• Use a string or wire to prevent the camera unit from falling and causing injury if the camera unit comes off from the wall.
• Do not mount the wall mounting adaptor to a ceiling.
• Do not mount the camera unit on a soft material. It may fall down, break or cause injury.
• Do not mount the camera unit on the following places: plaster board, ALC (autoclaved lightweight cellular concrete), concrete block, plywood less than 25 mm (1 inch) thick, etc.

1. Remove the screw and then remove the camera base from the camera unit.A. Supplied screw
2. Attach the wall mounting adaptor to the camera unit.
3. Drive the supplied screw into the camera unit.A. Supplied screw
4. Drive the screws (not supplied) into the wall.
   B. Longer than 20 mm (25/32 inches)
   C. Space 1.3 mm (1/32 inches)Note: Use the following template when determining the location of the screw holes.
5. Mount the camera unit to the wall.
   D. Screws
   E. 31 mm (1 7/32 inches)
6. Adjust the angle of the camera unit by using MFN, MEN, MDN, or MCN on the monitor unit.

Specifications

• Standards
  DECT (Digital Enhanced
  Cordless Telecommunications)
• Frequency range
  DECT: 1.92 GHz – 1.93 GHz
• RF transmission power
  DECT: 115 mW (max.)
• Power source
  Input: 100 – 240 V AC,
  50/60 Hz
  Output: 5.0 V DC, 1,000 mA
• Power consumption
  Normal operation: 2.8 W
  Night vision mode: 4.2 W
  Sleep mode: 2.1 W
• Operating conditions
  0 °C – 40 °C (32 °F – 104 °F) up to 90 % relative humidity (non-condensing)
• Transmitting range
  Up to 457.5 m (1,500 feet)*1
• Image sensor
  0.3 megapixel CMOS
• Minimum illuminance required
  0 lx*2
• Focal length
  Fixed (0.4 m (1.3 feet) – infinity)
• Angular field of view (camera angle)
  Horizontal: approx. 37°
  Vertical: approx. 28°
• Motion detection method
  Visual sensor
• Detection range
  Motion sensor:
  Horizontal: approx. 37°
  Vertical: approx. 28°
• Adjustable mounting angles
  Horizontal: ±136°
  Vertical: facing forward – facing
  down approx. +0° to -44°
  (movable range with the pan/tilt)
• Dimensions (height ´ width ´ depth)
  Approx. 123 mm ´ 77 mm ´
  69 mm (4 13/16 inches ´
  3 1/16 inches ´ 2 11/16 inches)
• Mass (weight)
  Approx. 224 g (0.49 lb)
  1. When used in the direction of maximum radiation, in the line of sight, and with no interference.
  2. The infrared LEDs that surround the camera lens will illuminate in low-light conditions.

FCC and other information (for U.S.A. users)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Privacy of communications may not be ensured when using this device.

CAUTION:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Some devices operate at frequencies that may cause interference to nearby TVs and VCRs. To minimize or prevent such interference, this device should not be placed near or on top of a TV or VCR. If interference is experienced, move this device further away from the TV or VCR. This will often reduce or eliminate interference.

FCC RF Exposure Warning:

• This product complies with FCC radiation exposure limits set forth for an uncontrolled environment.
• To comply with FCC RF exposure requirements, the device must be installed and operated 20 cm (8 inches) or more between the product and all person’s body.
• This product may not be collocated or operated in conjunction with any other antenna or transmitter.

Notice:
FCC ID can be found on the rear of the unit.

Limited Warranty (ONLY FOR U.S.A.)

Limited Warranty Coverage (For USA Only)
If your product does not work properly because of a defect in materials or workmanship, Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (“warranty period”), at its option either (a) repair your product with new or refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price. The decision to repair, replace or refund will be made by the warrantor.

Product or Part Name	Parts	Labor
Home Network System Products	One (1) Year	One (1) Year
microSD card (Included model only)	90 days	N/A

During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period, there will be no charge for parts. This Limited Warranty excludes both parts and labor for non-rechargeable batteries, antennas, and cosmetic parts (cabinet).
This warranty only applies to products purchased and serviced in the United States.
This warranty is extended only to the original purchaser of a new product which was not sold “as is”.