PELONIS Oil Filled Radiator Heater Manual

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury, including the following:

Read all instructions before using this heater.
This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces.
If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater and keep them away from the sides and rear.
Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
Always unplug heater when not in use.
Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater or return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
Do not use outdoors.
This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into bathtub or other water container.
Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
To disconnect heater, first turn controls to off, then remove plug from outlet.
Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
A heater has hot and arcing or sparking parts inside. Do not use it in the areas where gasoline, paint, or flammable liquids are used or stored.
Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
CAUTION: Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
This heater draws 12.5 amps during operation. To prevent overloading a circuit, do not plug the heater into a circuit that already has other appliances working.
It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet (receptacle) and plug may cause overheating and distortion of the plug. Contact a qualified electrician to replace loose or worn outlet.
The output of this heater may vary and its temperature may become intense enough to burn exposed skin. Use of this heater is not recommended for persons with reduced sensitivity to heat or an inability to react to avoid burns.
Don’t leave the heater on unattended.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT.

“SAVE THESE INSTRUCTIONS”

PART FIGURE

Air outlet, Fin, Display window, Control button, Caster assembly

Installation of the caster assembly

Place the heater body inversely with the bottom upward.
Figure1, expand the supporting foot outward into place.
Figure2, align the four casters to the supporting foot mounting holes and press them into the holes.

1 2

Note: The universal wheels are placed inside the foam at the bottom of the package.

Warning: Avoid to overturn, Expand the four casters outward into place.

OPERATING INSTRUCTION

: Temperature/ timer decrease
: ON / OFF button
: Temperature/ timer increase
: Timer button
MODE : Mode button
: Power indicating light, when the appliance is plug-in, the light will light up.

[Inspection before start]

The power cord shall not be damaged or fractured.
Please verify the rated current of the power socket is in line with the requirements in the table above and is equipped with a safety grounding device before use; otherwise, replace the socket.

[Operating Instructions]

<Turn on/Turn off>:Plug in power, buzzer gives off a sound of “beep”, press the on-off key “” to enter heating status at high gear and then press the on-off key “” for closing down.

<Gear selection>: For work status, press the gear key “MODE” gently to select one of work modes such as high gear, medium gear, low gear and energy saving gear.

[Timer function]

This function can be activated in two different ways
1) Delayed start: with the appliance off, press the timer button ““, the timer “” is displayed and hour ” h ” is flashing. Change the hours by pressing “” and “” buttons, then wait a few seconds for program to be stored. Once delayed start is settled, the delayed start hour and timer symbol “” remains on display.
2) Delayed stop: with the appliance on, press time button “” , the timer “” is displayed and hour ” h” is flashing, change the hours by pressing “” and “” buttons, then wait a few seconds for program to be stored. The current setting and timer symbol “” are displayed.
Note: the timer is settable from 0 to 24 hours.
Cancel the timer: There are three options for canceling delayed start/ stop setting:
a) Press on-off button ““
b) Press timer button “” and set the timer to 0 hour
c) Unplug the appliance.

[Temperature settings]

To select the desired temperature, press button “” or ““, By pushing the “” or “” button once , the temperature (shown on the display ) will increase or decrease by 1°F. Holding the ““or “” button depressed the value will increase or decrease rapidly .

Attention: When the heater is on ECO mode, The appliance allows the temperature range from 40°F to 95°F.
A. If the set temperature is higher than the room temperature, the heater will continue heating. The current settings and “” symbol are displayed; Once the room temperature reaches the set temperature, the heating element will stop heating, The “” symbol disappears from the display.
B. If the set temperature is lower than or equal to the room temperature , The heating element will stop heating .The current setting remains on but the “” symbol will not be displayed until the room temperature falls to below the set temperature, the appliance will resume heating. The current setting and the “” symbol are displayed.

<Children Lock Function> When the turning-on and standby status are valid without children lock, press on both “” and “MODE” for 3s at the same time to boot the children lock function. When the turning-on and standby status are valid with children lock, press on both “” and “MODE” for 3s at the same time to close down the children lock function.

Remarks:

When the children lock function works upon turning on, turn-off may be conducted and other operations are invalid (except for children lock releasing). Children lock function is cancelled upon turn-off.
If the children lock function works upon standby status, all operations are invalid (except children lock releasing).

<Memory function>: When the apparatus is closed down normally, it will run based on the latest status prior to closing down in the case of restarting. Power is off and the apparatus is closed down; the apparatus also runs based on the status prior to the power off in the case of power on for starting. Close down the apparatus normally, and cut off power; if the apparatus is energized for starting-up again, it runs based on factory default, namely, high gear operation, and the setting temperature is 95°F by default.

Note:
After power failure, the children lock function is not be memorized.

<Safety protection function>: If the indoor temperature (Th) exceeds 122°F, all output commands are terminated, the buzzer gives off an urgent sound for 10 times and digital screen displays “FF”, with 75s for 1Hz, whether standby or power-on. Even if the environmental temperature is less than 122°F, the running or operation cannot be recovered, as long as the protection exists; the only thing is to unplug the power cable, and then power up for operation.

[Stop]
Turn off the heater and then pull out the power plug.

[Movement of the heater]
To move the heater, turn it off first, and pull out the power plug; then push the body to make the four casters below the body to roll.

[Note]
To use the machine for the first time or to re-insert the socket, please pay attention to check whether the plug and the socket are fitted well.

<Inspection method>
Insert the power plug into the socket and start for use; after about half an hour, turn off and pull out the plug. Check whether the plug pins are hot, replace the socket if so (more than about 122°F) to avoid burning the plug or even causing a fire caused by overheating of the socket due to poor contact.

Special Note: This heater is provided with a safe feature to de-energize the power of heater when over-heating because of any abnormal operation. When it occurs, unplug the heater and check the abnormal conditions and eliminate them before attempting to use it. After cooling down, it may be energized for reuse.

USING THE REMOTE CONTROL

Instructions for remote control button function are basically consistent with the operation panel of the body, and the remote-control unit cannot control the combination key.

	ON/OFF button
	Mode button
	Temperature / Timer increase
	Temperature / Timer decrease
	Timer button

BATTERIES INSTRUCTIONS (included)

Please push locking latch in the direction of Arrow A, and pull out the pull notch in the direction of Arrow B at the same time.
Use 1 “CR2032” lithium battery (included)
Insert the batteries, making sure that the positive terminals are facing the proper way.
Replace the cover.

Battery installation

BATTERY WARNING

Do not dispose of batteries in fire, batteries may explode or leak.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
Non-rechargeable batteries are not to be recharged.
Batteries are to be inserted with the correct polarity.
Exhausted batteries are to be removed from the product.
The batteries must be removed from the remote controller before it is scrapped and that they are disposed of safely.

CARE AND CLEANING

Always remove the plug from the power socket and allow heater to cool. Wipe heater with a soft, damp cloth. Do not use detergents and abrasives.
If the heater is not in use over some days, wind the cable around the holder and store it in a dry place.
In case of malfunction, do not try to repair the heater by yourself. It may result in fire hazard or electric shock.
For any other service not mentioned in this instruction, it should be performed by an authorized service representative.

SPECIFICATIONS

Model No.: NY1506-18SRA
Voltage: 120V, 60Hz
Current: Maximum continuous draw: 12.5 Amps.
Rated Power: 1500W

DOWNLOAD RESOURCES

PELONIS Oil Filled Radiator Heater [pdf] User Manual Oil Filled Radiator Heater
Read more: https://manuals.plus/pelonis/oil-filled-radiator-heater-manual#ixzz7od1iDyCQ

FAQ’S

What is the difference between Pelonis and other heater brands?

Pelonis is a brand name of electrical heaters. It’s like comparing a Ford to a Chevy. They are both cars, but they are not the same.

What is the best way to clean my heater?

The best way to clean your heater is to use a damp cloth with mild soap and water. DO NOT USE A STRONGER SOLUTION!

How do I know if my heater has an automatic shut-off?

If your heater has an automatic shut-off, it will have a red button on the top of the heater. This button will pop up when your heater shuts off automatically. If you don’t see this button, then your unit does not have an automatic shut-off feature.

How do I know if my heater has an overheat protection feature?

If your heater has an overheat protection feature, it will have a red light on the top of the unit. This light will turn on when your unit overheats and automatically shuts off to prevent damage to your unit. If you don’t see this light, then your unit does not have an overheat protection feature.

Can you leave an oil filled radiator on all the time?

Yes, you can leave an oil heater “ON” overnight. Oil heaters are designed to be very safe, modern electric oil-filled heater comes with lots of additional advanced security features such as built-in-timers, tip-over protection, thermostat, and more.

How long can you run a Pelonis heater?

This heater offers users several options, with three heat modes (low, high, and ECO mode) and five settings. Its long list of safety features with everything from overheating protection to a 10-hour timer will allow you to breathe easy this winter.

Do oil filled radiators use a lot of electricity?

All the electricity used by an oil filled radiator is used to generate heat; namely by warming the oil inside. There is no electricity wasted. This makes the oil filled radiator one of the most energy efficient ways of heating any room. It is also surprisingly cheap to run!

Do oil filled heaters dry the air?

Oil-filled heaters are almost entirely silent. The most noise it makes is some clicking as the thermostat adjusts itself. Won’t dry the air. The lack of a fan means the air in your room won’t dry out either.

Can you get carbon monoxide poisoning from oil heaters?

Any appliances that use gas, oil, kerosene, or wood can produce carbon monoxide. When not properly ventilated, carbon monoxide emitted by these appliances can build up.

How long can you keep a Pelonis heater on?

Its long list of safety features with everything from overheating protection to a 10-hour timer will allow you to breathe easy this winter.

Are oil radiator heaters safe?

Because oil heaters do not rely on combustion, they do not typically produce toxic gases such as carbon monoxide. They can operate safely indoors without the need for ventilation. This greatly improves their safety relative to kerosene heaters and oil-burning furnaces.

Can oil filled radiators leak?

Oil filled electric radiators are very unlikely to leak. The thermal fluid heating element is fully encapsulated inside the radiator body. The fluid expands as it heats up, and is kept at pressure by an automatic pressure valve.