SAMSUNG Washer and Dryer Stacking Kit Installation Guide
STACKING KIT INSTALLATION INSTRUCTIONS (WASHER and DRYER ONLY)
CAUTION : Two people are required to lift the dryer on to the washer.
WARNING : These washer and dryer are not suitable for mobile home or RV installation.
Dryer
STEP 1 : Have two persons place the dryer on a non-slippery floor. Then, have one person tilt the dryer to the side. Do not lay the dryer down. The dryer may be scratched.
STEP 2-1 : SKK-7*, SKK-8*: Check if the legs are tightened up, and then insert the stacking support guides in the rectangular holes of the dryer’s base until you hear a clicking sound. You don’t need to remove the legs.
STEP 2-2 : SKK-BB: Disassemble legs, and Snap the stacking support guides into the rectangular holes in the dryer base and secure each with two(2) screws Phillips-pan head (6006-001174)
STEP 3 : Repeat the same step above on the other side.
STEP 4 : Bottom view of the dryer after assembling the Stacking Support Guides to the dryer base. * Use a stacking-kit compatible with the purchased model.
Washer (Stacking kit: SKK-7*, SKK-8*, for 27” models)
CAUTION : You need to use the proper rear bracket depending on your washer model. (There are 2 different rear brackets : DC61-04160A, DC61-04955A)
5-1) DC61-04160A : WF5*K**, WF4*H**, WF4*K**, WF4*M**, WF4*N**, WF18H**, WF20H**, WF20M**, WF22H**, WF22K**, WF15K**, WF16J65**
DO NOT TIGHTEN SCREWS COMPLETELY
STEP 5-1 : LOOSELY assemble the Rear Brackets (DC61-04160A) to the washer as shown below. Use two (2) Screws-Hex Head (6002-001431) with washers (DC60-00044A) in each washing machine Top Cover tail, per bracket. * Before installing the rear bracket, loosen two screws (Screw-Hex) on the Cover Top that is secured to the frame.
5-2) DC61-04955A : WF5*R**, WF4*R**
DO NOT TIGHTEN SCREWS COMPLETELY
STEP 5-2 : LOOSELY assemble the Rear Brackets (DC61-04955A) to the washer as shown below. Use two (2) Screws-Hex Head (6002-001431) with washers (DC60-00044A) in each washing machine Top Cover tail, per bracket. * Before installing the rear bracket, loosen two screws (Screw-Hex) on the Cover Top that is secured to the frame.
Washer (Stacking kit: SKK-BB, for 30” models)
WF56H** :
STEP 5-3 : Loosely assemble the Rear Bracket (DC61-03846A) to the washer as shown above in either case A or Case B, Use (2) Screws-Hex Head (6009-001476) with washers (DC60-00044A) to the each hole of Cover Top and Frame. * Case A only : Before installing the rear bracket, loosen two screws (Screw-Hex) on the Cover Top that is secured to the frame.
STEP 6 : Lift and position dryer into the position on the washer shown above, slide dryer backwards to make contact with rear brackets
CAUTION : To prevent noise, check the followings.
- Make sure the washer is level.
- Make sure the dryer’s leveling legs are tightened up. (Stacking kit: SKK-7*, SKK-8*, for 27” models).
STEP 7 : Align rear brackets with mounting holes on the rear of dryer as shown above.
STEP 8 : LOOSELY assemble rear brackets to the back of the dryer using two (2) Screws- Phillips Pan Head (6006-001174) for each rear bracket as shown above. Extra screws may be included with this kit.
STEP 9 : Tighten screws on the dryer side of the rear bracket.
WARNING : Additional gas hook-up components are required for gas dryer.
STEP 10 : Tighten screws on the washer side of the rear bracket.
- DO NOT REVERSE THE ORDER OF STEPS 9 & 10.
STEP 11 : Stacked Unit is now ready to be installed. Refer to detailed installation instructions packed with products.
Stacking kit components
| Stacking Support Guides (2) | SKK-7*, SKK-8* – | – DC61-04159A |
| Rear Bracket (2) (WF5*K**, WF4*H**, WF4*K**, WF4*M**, WF4*N**, WF18H**, WF20H**, WF20M**, WF22H**, WF22K**, WF15K**, WF16J65** | SKK-7*, SKK-8* | – DC61-04160A |
| Rear Bracket (2) (WF5*R**, WF4*R**) | SKK-7*, SKK-8* – | – DC61-04955A |
| Stacking Support Guides (2) | SKK-BB | – DC61-01480B |
| Rear Bracket (2) (WF56H** | SKK-BB | – DC61-03846A |
| Screws-Hex Head (4) | SKK-BB
SKK-7*, SKK-8* |
– 6009-001476 |
| Screws Phillips-Pan Head (8) | – | – 6006-001174 |
| Washer (4) | – | – DC60-00044A |
- Rear Bracket : (WF5*K**, WF4*H**, WF4*K**, WF4*M**, WF4*N**, WF18H**, WF20H**, WF20M**, WF22H**, WF22K**, WF15K**, WF16J65**)
- Rear Bracket : (WF56H**)
- Rear Bracket : (WF5*R**, WF4*R**)
- Screw-Hex Head : SKK-BB (M5, L10) SKK-7*, SKK-8* (M5, L16)
- Screw Phillips-Pan Head : (M4, L12)
- Washer : (ID5, OD10)
- Stacking Support Guide
