PROHEAT® 2X REVOLUTION® PET PRO
QUICK START/USER GUIDE
1986 Series
More of a video person? Look for this icon and go online for an instructional how-to video at www.BISSELL.ca
Built for Pet Owners
CleanShot
Use the onboard pretreat CleanShot at any time while deep cleaning your carpet to target and remove tough stains and odors.
EZ Clean Brush Roll Cover
BISSELL’s first deep cleaner with a nozzle and brush roll cover that’s simple to remove and clean after use.
by Pet Owners
New! Specialized Pet Tools
Easily vacuum and deep clean your upholstery with the new 2-in-1 Pet Upholstery Tool.
Remove Pet Hair, Stains and Odors with a single tool.
Dry Mode:
Use the green switch to change cleaning modes. Begin with Dry Mode to vacuum and remove hair and debris. Use a raking motion to engage the rubber and attract hair to the suction channel.
Wet Mode:
Switch to Wet Mode to deep clean. Keep the tool in contact with the surface and press the trigger to release spray while pulling the tool toward you.
Quick Start Guide
WARNING
Do not plug in your deep cleaner until you are familiar with all instructions and operating procedures.
Your deep cleaner comes in four easy-to-assemble components and an accessory bag.
- Base
- Upper Handle
- Clean Water Tank
- Carry Handle
A Phillips screwdriver is required for Assembly in Step 3. 
First, insert the (aluminum) Upper Handle at the top of the base until you hear a “click”. Do NOT put the clean tank on the machine until Step 5.
Next, align the carry handle with the slots on either side of the base (behind the power switch and cleaning mode switch). The carry handle will “click” into place.
Use a Philips screwdriver to secure the screw (found taped to upper handle) into the carry handle.
Wrap the cord around the carry handle and Quick Release™ Cord Wrap hook.
Side View:
At the bottom of the upper handle, align the clean water tank with the grooves and slide the tank into place.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR DEEP CLEANER.
When using an electrical appliance, basic precautions should be observed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:
- Connect to a properly grounded outlet only. See grounding instructions. Do not modify the 3-prong grounded plug.
- Do not leave appliance when it is plugged in. Unplug from outlet when not in use and before servicing.
- Do not expose to rain. Store indoors.
- Do not allow to be used as a toy. Close attention is necessary when used by or near children.
- Do not use for any purpose other than described in this User’s Guide. Use only manufacturer’s recommended attachments.
- Do not use with damaged cord or plug. If appliance is not working as it should or has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.
- Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.
- Do not run appliance over cord. Keep cord away from heated surfaces.
- Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
- Do not handle plug or appliance with wet hands.
- Do not put any object into openings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.
- Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
- Turn off all controls before plugging or unplugging appliance.
- Use extra care when cleaning on stairs.
- Do not use to pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in areas where they may be present.
- Do not use appliance in an enclosed space filled with vapors given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapors.
- Do not use to pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
- Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
- Use only BISSELL cleaning products intended for use with this appliance to prevent internal component damage. See the Cleaning Formula section of this guide.
- Do not immerse. Use only on surfaces moistened by the cleaning process.
- Keep appliance on a level surface.
- Do not carry the appliance while in use.
- Always install float before any wet pick-up operation.
- Unplug before connecting TurboBrush® Tool.
SAVE THESE INSTRUCTIONS
FOR FUTURE USE
This model is for household use only. Commercial use of this unit voids the manufacturer’s warranty.
WARNING
Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service person if you aren’t sure if the outlet is properly grounded. DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is designed for use on a nominal 120-volt circuit, and has a grounding attachment plug that looks like the plug in the illustration. Make certain that the appliance is connected to an outlet having the same configuration as the plug. No plug adapter should be used with this appliance.
GROUNDING INSTRUCTIONS
This appliance must be connected to a grounded wiring system. If it should malfunction or break down, grounding provides a safe path of least resistance for electrical current, reducing the risk of electrical shock.
The cord for this appliance has an equipment-grounding conductor and a grounding plug. It must only be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Thanks for buying a BISSELL carpet cleaner!
We love to clean and we’re excited to share one of our innovative products with you. We want to make sure your carpet cleaner works as well as it does today for years to come, so this guide has tips on using (pages 10-13), maintaining (pages 16-19), and if there’s a problem, troubleshooting (page 20).
In just a few simple assembly steps, you’ll be ready to deep clean. Flip to the front and let’s get started!
Package Contents
Upper Handle- 1 Screw attached to Upper Handle
- Base with Dirty Water Tank
- Clean Water Tank
- Carry Handle
- BISSELL Professional Pet Urine Eliminator + Oxy
- BISSELL Deep Clean + Sanitize Trigger (Trigger not pictured)
- Accessory bag & hose
- Tough Stain Tool
- 2-in-1 Pet Upholstery Tool
- Nozzle Clean Out Tool
NOTE: Standard accessories may vary by model. To identify what should be included with your purchase, please refer to the “Carton Contents” list located on the carton top flap.
Getting to Know Your Deep Cleaner
Cleaning Formulas
WARNING
To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL cleaning fluids intended for use with the deep cleaner.
Keep plenty of genuine BISSELL formula on hand so you can clean and protect whenever it fits your schedule.
Always use genuine BISSELL deep cleaning formulas. Non-BISSELL cleaning solutions may harm the machine and may void the warranty.
| BOOST
CARPET CLEANING FORMULA ENHANCER |
PRETREAT
PRE TREAT SPOTS AND STAINS TO IMPROVE CARPET CLEANING PERFORMANCE |
SANITIZE
USE IN BETWEEN DEEP CLEANING |
||
 |
 |
 |
 |
 |
| Oxy Boost | Renew Boost | Pet Oxy Boost | Oxy Stain Destroyer | Deep Clean + Sanitize |
| Removes old, set-in stains permanently | Revives carpets to look their best | Removes pet stains and odors permanently | Permanent Stain Removal in 30 seconds | Kills 99.9% of bacteria* |
| PROFESSIONAL 2X* CLEANING FORMULAS | 2X* CLEANING FORMULA | |||||
 |
 |
 |
 |
 |
 |
 |
| Professional Pet Urine Eliminator + Oxy | Professional
Deep Cleaning |
Pet Stain & Odor | DeepClean
& Protect |
Allergen Cleansing | DeepClean + Refresh | Deep Clean + Oxy |
| Our best formula for pet urine stains & odors Includes Scotchgard™ Protector | Out cleans all other formulas Includes Scotchgard™ Protector | Removes tough pet stains Includes Scotchgard™ Protector | Deep cleans carpets and protects from future stains with Scotchgard™ Protector | Helps remove pet & pollen allergens | Powerful cleaning with a refreshing scent | Removes deep down dirt, pet stains, & pet odor |
ONLY BISSELL Protects from future stains with Scotchgard™ Protector.
Scotchgard™ is a trademark of 3M®.
*2.5 fl. oz. of 2X concentrated formula is equivalent to 5.0 fl. oz. of non-concentrated formula.
Tips Before Carpet Cleaning
- If cleaning an entire room, consider moving your furniture to another area.
- Remove any dry debris or loose impediments before using your deep cleaner.
- Pre-treat stains with BISSELL PreTreat to improve performance on coffee stains and ground-in dirt.
*on soft surfaces in one minute and on carpet (not for use on polypropylene/olefin or wool fibres) in one hour.
Customize Your Clean and Maximize Your Results
ELIMINATE PET URINE, STAINS & ODORS
Our best formula for pet urine, stains, and odors. Permanently remove all three from your carpet!
For Pet Stains & Odors:
Erase pesky stains & remove odors!
Pretreat pesky pet stains with BISSELL Pretreat spray before using your deep cleaner. Choose a BISSELL pet formula for your deep cleaner and clean as directed.
To Clean Dark Stains:
Remove stains permanently!
Use BISSELL Deep Clean + Oxy formula or add BOOST OXY to any of your favorite BISSELL formulas to maximize the stain removal power.
To Remove Ground-In Dirt:
Renew your carpet!
Pretreat ground-in dirt with a BISSELL Pretreat Spray. Choose BISSELL Professional Deep Cleaning formula and pair with a BISSELL Boost to enhance your cleaning.
To Refresh Your Home:
Choose your favorite scent!
Pair your carpet cleaner with BISSELL Febreze™ formulas to give your home a clean and refreshing scent.
To Sanitize In-Between Deep Cleaning:
Use BISSELL Deep Clean + Sanitize
Use BISSELL Deep Clean + Sanitize in between deep cleaning to kill 99.9% of bacteria on soft surfaces in one minute and on carpet (not for use on polypropylene/ olefin or wool fibres) in one hour.
Always use genuine BISSELL deep cleaning formulas. Non-BISSELL cleaning solutions may harm the machine and may void the warranty.
Filling Your Clean Water Tank:
The clean water tank is at the top of the machine.
Lift the clean water tank straight up to remove from the machine.
Unscrew the cap from the clean water tank. Add hot tap water to the water fill line. Next, reference the chart below for formula amounts to add to the tank. Twist cap back into place.
At the bottom of the upper handle, align the clean water tank with the grooves and slide the tank into place.
FORMULA FILLING INSTRUCTIONS
BISSELL 2X Concentrated Formulas
DEEP CLEAN MODE
Fill water to the Water Fill Line that is next to DEEP CLEAN MODE on the Clean Tank. Add 2.5 oz of formula.
EXPRESS CLEAN MODE
Fill water to the Water Fill Line that is next to EXPRESS CLEAN MODE on the Clean Tank. Add 1.25 oz of formula.
NOTE: Fill with hot (140°F/60°C MAX) tap water and add the appropriate BISSELL solution. DO NOT USE BOILING WATER. DO NOT HEAT WATER OR TANK IN MICROWAVE. Do not substitute BISSELL 2X Formula cleaning solution with other household cleaning products.
Pour in more power with BISSELL Boosts
- Fill tank with water and 2X formula (Step 3 above).
- Add 2 ounces of any BISSELL Boost per 1 gallon of water.
- The ProHeat 2X Revolution has a 1 gallon clean water tank.
Cleaning Your Carpet
Plug into a properly grounded outlet.
Select cleaning mode:
Deep Clean – Delivers a deep clean to your carpet.
Express Clean – Provides a lighter clean with about 1 hour of dry time.
Press the power button to turn the machine on.
To recline your machine for use, press the recline pedal with your foot.
NOTICE: To prevent damage to Berber carpets, avoid repeated strokes in the same area.
Deep Clean Mode:
- Press the spray trigger to apply solution while making 2 slow wet passes – 1 forward and 1 back.
- Release the trigger.
- Make 2 slow dry passes – 1 forward and 1 back, to suck up the dirty solution. (Do not hold down the trigger for this step.)
NOTE: For best cleaning performance, clean with your machine in Deep Clean Mode.
Express Clean Mode:
- Press the spray trigger to apply solution while making 2 wet passes – 1 forward and 1 back.
- Release the trigger.
- Make 2 dry passes – 1 forward, 1 back to suck up the dirty solution. (Do not hold down the trigger for this step.)
NOTE: In Express Clean Mode, the dirty tank will not get as full as when cleaning with Deep Clean Mode.
Area Rug Cleaning
Important! Please check manufacturer’s tag before cleaning area rugs for any specialized cleaning instructions. We do not recommend deep cleaning delicate, silk, wool, antique or area rugs without a manufacturer’s tag.
Regularly clean your high-traffic area rugs in Express Clean Mode:
- Check the manufacturer’s tag.
- Select Express Clean Mode.
- When cleaning area rugs, place the rug on a sealed surface to test for colorfastness in an inconspicuous area. Your cleaner should not be used on unsealed surfaces.
- Important: Keep the foot of the deep cleaner perpendicular to the rug’s edge with each cleaning pass to prevent damage.
Cleaning with Hose and Tool
Lift the accessory hose door on top of foot on the front of the machine. The door flips toward the machine to open.
Insert the hose and snap into place. Be sure the colored hose release clip is facing out, away from machine.
Attach the tool to the end of the hose. (Tools may vary by model.) Press the power button to turn machine on.
— Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. Brushroll continues to rotate when in the upright position.
— Brushroll continues to turn while product is turned on and handle is in upright position. To avoid damage to carpet, rugs, furniture and flooring, avoid tipping cleaner or setting it on furniture, fringed area rugs, or carpeted stairs during tool use.
— The brushroll remains on while cleaning with the hose and tool. Do not allow cleaner to sit in one location for an extended period of time, as damage to floor can result.
Press the spray trigger button to spray the soiled area, then slowly move tool back and forth over the area.
Release the trigger to suck up the dirty solution. Work in small sections until the area is clean.
When finished cleaning, turn the machine on to suction up warm clean water to rinse the inside of the hose and tool. Detach the hose and tool and close the accessory hose door. Let the hose and tool air dry before storing.
NOTE: If using the Deep Reach Tool or Pet Stain Tool be sure the needles of the tool are pressed down into the carpet so the spray gets into the carpet fibers.
Cleaning with CleanShot
Press the CleanShot button with your foot. The window of the button will be green and show an “I” symbol when it is on.
Spray will continue until you turn it off. To turn CleanShot off, press the button with your foot. The window of the button will be red and show an “O” symbol when it is off.
Completely cover the stain with CleanShot spray. Allow the stain to soak. To extract, maneuver the foot of the machine over the stain to brush and remove.
2-in-1 Pet Upholstery Tool
*Make sure your clean tank has water & formula to use the tool in wet mode.
Follow hose plug-in instructions from steps 1 & 2 on page 14.
Attach the tool and select dry mode to first pick up dry debris and pet hair. The suction will be at the lower part of the tool, near the dry cup.
DRY MODE NOTE: Use a “raking” motion to clean. Start with the tool farthest away and rake in small increments as you bring the tool toward you. The rubber nubs will help attract hair to the suction channel.
Empty the cup when it fills with hair and debris.
Turn off the machine. Hold the cup and twist counterclockwise line up the arrow with the unlock symbol and remove.
Take off the cup to empty hair and debris.
Remove hair that may wrap around the filter.
To reattach the cup, line up the cup to the tool indents, and rotate clock wise. The arrow will line up with the locked icon when secured.
To Deep Clean, move the switch to wet mode.
Press the trigger to spray your water and formula; use the top of the nozzle to extract stains and odors.
To remove any hair or trapped debris from the nozzle, first turn off the machine. Pull the nozzle tab away from the tool to remove and rinse under running water.
Replace to the tool by lining up the nozzle edge and snap into place.
Before storing, make sure all hair is removed from the dry cup and nozzle has been rinsed under running water.
WET MODE NOTE: Start from the area farthest away. Hold the trigger down, and pull the tool toward you. Keep the tool in contact with the surface as you pull. You will see extraction through the nozzle.
Empty Dirty Water Tank
WARNING
To reduce the risk of fire, electric shock or injury, turn power OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting.
To release dirty water tank, press down on the colored tank handle.
Tilt the tank slightly toward you.
Grab the handle and tank with both hands and pull the dirty water tank up and away to remove.
For quick empty: Pull the rubber tab and tilt to pour. (Located at the corner of the top of the tank.) When closing the rubber tab, make sure all edges are sealed tight.
For final clean and rinse: Unscrew the ring at the bottom of tank.
Gently remove the float stack, rinse, and clean.
Once clean, return float stack into the tank by lining up the arrows so they point at each other. This is the only way the float stack will fit into the tank.
With the arrows aligned, the float stack should lock into place.
Return the ring and twist to lock. Water may leak if the ring is not fully tightened.
Clean the red filter below the dirty tank by wiping off any remaining dirt or debris.
To return the dirty tank: Angle the tank and insert bottom first. Then tilt the tank toward the machine and push the top in until it clicks into place.
Did You Know?
The Float Stack is what prevents your dirty tank from overflowing.
Cleaning Machine After Use
WARNING
To reduce the risk of electric shock, turn power switch off and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.
To reduce the risk of electric shock, turn power switch off and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.
First, fill the clean water tank with warm tap water and then empty it all to rinse. Then fill again with warm tap water and return the tank to the machine.
Twist cap back on tightly.
Finally, release the trigger and extract the water.
See page 16 to clean the dirty tank from the water that was just extracted.
Empty the clean water tank and let dry before storing.
Wipe your machine’s exterior with a soft cloth.
Store machine in a protected dry area.
Brush Roll and Nozzle Care
NOTE: Be sure to clean the brush rolls and nozzle before storing your machine.
Follow these steps if your nozzle becomes clogged with hair or debris.
Turn off and unplug the machine from the grounded outlet.
Remove the nozzle from the foot: scoop and grip the Accessory Hose Door. Pull up to remove the nozzle.
Next, remove the next layer, the brush roll cover, to reveal the brush rolls.
Press on the two release buttons and lift straight up.
At this point, the nozzle and brush roll cover can be rinsed under running water and the nozzle clean out tool can be inserted to unclog hair or debris.
NOTICE: To reduce the risk of a leaking condition, do not store unit where freezing may occur. Damage to internal components may result.
Use the comb to brush out the debris or hair from the brush rolls
When finished, return the brush roll cover by pushing it straight down. You will here a click from each “push” button when the cover is pushed down into place. Line up the nozzle from the edge near the floor and rotate to snap back into place.
Replacing Belts and Brush Rolls
What you will need: 1 Phillips screwdriver & 1 flathead screwdriver
While the machine is upright, unplug the machine and remove both tanks. Remove the nozzle and brush chamber cover (see steps in Brush Roll & Nozzle Care). Press the recline pedal and lay the machine on its back.
Use a flathead screwdriver and press it into the slot at the back and then front of the belt access door. Lift to remove the Belt Access Door.
NOTE: To replace brush rolls, remove them from the metal posts and replace. Make sure the metal post goes completely through the end of the brush roll. The brush roll bristles should be aligned in a ‘V’ pattern as pictured.
The other brush roll rotates with it.
Check that washers are in place.
Reassemble the belt and end cap, securing with screws you removed.
If it needs replacing for any reason, the gear belt should already be removed before removing the flat belt.
Rotate the machine back to its side. Feed the new flat belt through the opening so that it wraps around the red pulley.
Snap the Belt Access Door back down into place.
NOTE: See Step 6 on page 18 for hobgw to put the brush roll cover and nozzle back in place.
Troubleshooting
WARNING
To reduce the risk of electric shock, turn power switch off and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.
| Problem | Possible causes | Remedies |
| Reduced or No Spray
Through Foot of Machine |
Clean water tank may be empty | Refill tank |
| Clean water tank may not be seated completely | Turn power OFF; remove and reseat tank | |
| No spray through hose & tool | The hose to your machine is not primed or may have lost prime | 1. With the machine off and unplugged, remove the nozzle from the foot. Place a ball point pen in the black cylinder next to the screw. When water bubbles up, remove the pen. Reassemble the nozzle and hose
2. Hold end of hose below water level in tank to prime 3. With the clean tank full of water, the machine OFF and RECLINED, press the CleanShot button ON and wait for the CleanShot to drain for a few seconds; This will re-prime the machine |
| Clean Water tank may be empty | Refill the Clean Water Tank | |
| Clean Tank may not be seated properly | Turn power OFF; Remove and reseat the clean water tank | |
| No Spray Through CleanShot | Clean Water tank may be empty | Refill the Clean Water Tank |
| Clean Tank may not be seated properly | Turn power OFF; Remove and reseat the clean water tank | |
| The machine is not reclined | Press the Recline pedal and bring the handle down to recline the machine | |
| Pump may have lost prime | With the machine off and unplugged, remove the nozzle from the foot. Place a ball point pen in the black cylinder next to the screw; When water bubbles up, remove the pen; Reassemble the nozzle before cleaning again | |
| CleanShot Continues Spray When Machine is Off | CleanShot button is not in the “OFF” position | Press the CleanShot button to turn it off. The button window will show the color red and a “O” symbol when it is in the off position |
| Loss of suction power | Dirty tank may not be seated properly | Pick up the dirty tank and reseat so it fits in the unit |
| Dirty tank has picked up maximum amount of dirty water and has reached full line | Empty dirty tank | |
| Rubber tab on dirty water tank is not sealed tight | Check the rubber tab on the dirty water tank and press firmly on all edges to secure it tightly (see step 4 on page 16 for detail) | |
| Accessory hose door may not be closed tightly in place | Check the accessory hose door and make sure it is closed tightly – it should be locked into place | |
| Nozzle may be clogged from pet hair or debris | Use the nozzle clean out tool and follow steps on page 17 for “Cleaning Nozzle” | |
| Brush roll cover not fully snapped into place | Remove the nozzle and brush roll cover; Follow step 6 from page 18 and make sure you hear both buttons click into place | |
| No power | Cleaning mode switch mistaken for power button | Press the red power button on the left side of the machine to turn the machine on |
| Outlet may not be active | Try plugging in a different device that uses a grounded outlet to test for power from the outlet | |
| Leaking tank | Tank may have been over-filled | 1. Make sure your tank has the water and formula in it that you’ve prepared
2. With the cap twisted ON tightly, hold your tank at an angle, over a sink or drain, so any extra water can pour out of the space 3. Wipe the tank dry with a cloth |
| Water may be caught in space between the tank and the tank’s handle |
Warranty
If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Care by E-mail, telephone, or regular mail as described below.
Limited Five-Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for five years any defective or malfunctioning part.
See information below on “If your BISSELL product should require service”.
This warranty applies to products used for personal, and not commercial or rental service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User’s Guide is not covered.
BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT. *EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE FIVE-YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim.
Service
If your BISSELL product should require service:
Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Care.
Website: www.BISSELL.ca
E-mail: www.BISSELL.ca/email-us
Call: BISSELL Consumer Care
1-800-263-2535
Monday – Friday 8am – 10pm ET
Saturday 9am – 8pm ET
Sunday 10am – 7pm ET
Please do not return this product to the store.
Other maintenance or service not included in the manual should be performed by an authorized service representative.
For any questions or concerns, BISSELL is happy to be of service.
Contact us directly at 1-800-263-2535.
Register your product today!
Registering is quick, easy and offers you benefits over the lifetime of your product.
You’ll receive:
Faster Service
Supplying your information now saves you time should you need to contact us with questions regarding your product.
Product Support Reminders and Alerts
We’ll contact you with any important product maintenance reminders and alerts.
Special Promotions
Optional: Register your email to receive notice of offers, contests, cleaning tips and more!
Visit www.BISSELL.ca/registration!
Visit us online at: BISSELL.ca
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ____________________________________
Please record your Purchase Date: _____________________________________
NOTE: Please keep your original sales receipt.
It provides proof of purchase date in the event of a warranty claim. See Warranty on page 21 for details.
Parts & Supplies
For Parts and Supplies, go to BISSELL.ca and enter your model number in the search field.
We can’t wait to hear from you!
We really do read your comments, tweets, and posts.
Rate this product on BISSELL.ca
or any of our retailer sites and let us (and millions of your closest friends) know what you think!
For cleaning tips and more visit www.BISSELL.ca or find us at:
©2017 BISSELL Homecare, Inc
BISSELL Canada Corporation
Mississauga (Ontario) L5N 0B3
All rights reserved. Printed in China
Part Number 161-0844 Rev 05/17
Visit our website at: www.BISSELL.ca
Scotchgard is a trademark of 3M
