PROheat2x™ USER’S GUIDE 8920, 8930, 8960, 9200, 9300, 9400 SERIES
Product view
|
|
Cleaning fluid
Keep plenty of genuine Bissell 2X formula on hand so you can clean and protect it whenever it fits your schedule. always use genuine Bissell deep cleaning formulas. non-Bissell
Special features
Built-in-heater feature
Custom Clean
Flow indicator (select models only)
Scotchgard
- Pretreating is recommended to improve cleaning effectiveness for heavily soiled carpets in high traffic areas such as entryways and hallways.
- 8a. 8b.
hot tap water, following instructions 1c through 1e on page 10.
|
|
- the 2-in-1 water tank and the formula tank.
|
|
- Clean under warm water before storing.
- Caution: Do not overwet.
|
|
Maintenance and care
|
|
- IMPORTANT: cord side down.
|
|
Troubleshooting
Built-in heater ready light does not illuminate Possible causes
1. The heater switch is not turned ON ( I )
2. The power switch is not turned ON ( I )
Remedies
1. Turn the heater switch ON ( I )
2. Both switches must be ON ( I ) to activate the heater ready light
Reduce Spray or No Spray Possible causes
1. Water tank may be empty
2. Formula tank may be empty
3. Tank may not be seated completely
4. Pump may have lost prime.
Remedies
1. Fill the heavy-duty bladder with hot tap water
2. Fill formula tank with BISSELL 2X Formula for cleaning
3. Turn power OFF (0). Remove and reseat tank
4. Turn power OFF (0) and then back ON (I). Wait one minute, then depress trigger
DirtLifter® PowerBrush does not turn Possible causes
1. The belt is off or broken
2. The unit is in the upright position
3. Circuit breaker on the machine may have tripped
Remedies
1. Turn power OFF ( O ) and unplug the unit from the outlet. Follow instructions on page 19
2. Brushes only rotate when the unit is reclined using the detent pedal
3. Turn the machine OFF ( O ) and unplug from the outlet. Check to see if a foreign object is caught in the brush roll. Remove object. Plug machine in to reset circuit breaker
Cleaner not picking up solution Possible causes
1. ReadyTools dial may be at wrong setting
2. Tank may not be seated properly
3. Tank may not be assembled properly
4. Solution or 2-in-1 water tank is empty
5. 2-in-1 water tank has picked up maximum dirty water and red float door has closed.
6. Red float “door” in the tank may have closed as a result of bumping an object or moving the machine back and forth too quickly
Remedies
1. Set ReadyTools dial to either FLOOR CLEANING or TOOLS setting
2. Pick up both the 2-in-1 water tank and formula tank and reseat them so they fit snugly on the unit
3. Check to make sure the “lip” of the nozzle is securely hooked into the groove on the bottom of the Tank (see page 10)
4. Check fluid levels in heavy-duty bladder and formula tank.
5. Empty 2-in-1 water tank. Refill heavy-duty bladder with clean hot tap water and replace it.
6. Turn the machine OFF ( O ), allowing the red float door to release
arranty – BISSELL PROheat 2X
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
©2011 Bissell Homecare, inc
Bissell canada corporation
Mississauga, Ontario l5n 0b3
all rights reserved. Printed in china
Part number 120-4342
Rev 1/11
Visit our website at: www.bissell.ca
Scotchgard is a registered trademark of 3m
