Dyson SV18 Digital Slim appliance

IMPORTANT SAFET Y INSTRUCTIONS

BEFOR E US ING THIS A PPLI A NCE R E A D A LL INS TRUC TIONS A ND C AUTION A RY M A R K INGS IN THE US ER M A NUA L A ND ON THE A PPLI A NCE.
When using an electrical appliance, basic precautions should always be followed, including the following:

WARNING

These warnings apply to the appliance, and also where applicable, to all tools, batteries, accessories, chargers or mains adaptors.

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

1. The appliance is not intended for use by persons (including children) with reduced physical, sensor y or mental capabilities, or lack of experience and knowledge, unless they have been given super vision or instruction concerning use of the appliance by a person responsible for their safety.
2. Do not allow to be used as a toy. Close attention is necessary when used by or near children. Children should be super vised to ensure that they do not play with the appliance.
3. Use only as described in the Dyson User manual. Do not carry out any maintenance other than that shown in the manual, or advised by the Dyson Helpline.
4. Suitable for dry locations ONLY. Do not use outdoors or on wet sur faces.
5. Do not handle any par t of the charger or appliance with wet hands.
6. Do not use with a damaged cable or plug. If the supply cable is damaged it must be replaced by Dyson, its service agent or similarly qualified persons in order to avoid a hazard.
7. If the appliance is not working as it should, if it has received a sharp blow, if it has been dropped, damaged, left outdoors, or dropped into water, do not use and contact the Dyson Helpline.
8. Contact the Dyson Helpline when a service or repair is required. Do not disassemble the appliance as incorrect reassembly may result in an electric shock or fire.
9. Do not stretch the cable or place the cable under strain. Keep the cable away from heated sur faces. Do not close a door on the cable, or pull the cable around sharp edges or corners. Arrange the cable away from traffic areas and where it will not be stepped on or tripped over. Do not run over the cable.
10. Do not use to pick up water.
11. Do not use to pick up flammable or combustible liquids, such as petrol, or use in areas where they or their vapours may be present.
12. Do not pick up any thing that is burning or smoking, such as cigarettes, matches, or hot ashes.
13. Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts, such as the brush bar. Do not point the hose, wand or tools at your eyes or ears or put them in your mouth.
14. Do not put any objects into openings. Do not use with any openings blocked; keep free of dust, lint, hair and any thing that may reduce air flow.
15. Use only Dyson recommended accessories and replacement parts.
16. Do not use without the clear bin and filter(s) in place.
17. Unplug the charger when not in use for ex tended periods of time.
18. Unplug the charger and disconnect the batter y pack from the appliance before carrying out any cleaning or user maintenance.
19. Use extra care when cleaning on stairs.
20. To prevent unintentional star ting, be careful to keep your hands and fingers away from the power trigger until you are ready to begin vacuuming, especially when picking up or carrying the appliance. Carrying the appliance with your finger on the power trigger invites accidents.
21. Do not install, charge or use this appliance outdoors, in a bathroom or within 3 meters (10 feet) of a pool. Do not use on wet sur faces and do not expose to moisture, rain or snow.
22. Use only Dyson charger Par t Number 31120 0 for charging this Dyson appliance and only use the batteries, Par t Number 398857- 01. Only use genuine Dyson batteries as other types may explode, causing injury and damage.
23. When removing or replacing a motorised brush bar, be careful not to pull the power trigger until the cleaner head has been reassembled.
24. Disconnect the battery from the appliance before storing for ex tended periods of time.
25. When the battery is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shor ting the battery terminals together may cause burns or a fire.
26. Do not use a battery or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury. The battery used in this appliance may present a risk of fire or chemical burn if mistreated. Do not place the appliance on or near a cooker or any other hot sur face and do not disassemble or short-circuit the battery ‘s supply terminals. Do not expose the battery or appliance to fire or excessive temperatures. Exposure to fire or temperatures above 60 °C (140 ° F) may cause explosion.
27. Exhausted or damaged batteries should be removed from the appliance before it is discarded. When removing the battery, the appliance must be powered of f. Safely dispose of the battery in accordance with local ordinances or regulations.
28. The battery is a sealed unit and under normal circumstances poses no safety concerns. In the unlikely event that liquid leaks from the batter y, do not touch the liquid as it may cause irritation or burns, and observe the following precautions:
    • Skin contact – can cause irritation. Wash with soap and water.
    • Inhalation – can cause respirator y irritation. Expose to fresh air and seek medical advice.
    • Eye contact – can cause irritation. Immediately flush eyes thoroughly with water for at least 15 minutes. S eek medical attention.
    • Disposal – wear gloves to handle the battery and dispose of immediately, following local ordinances or regulations
29. Follow all charging and battery instructions and refer to the ‘Changing your battery ‘ section on how to change the battery. Do not charge the battery or the appliance outside of the temperature range specified below. Charging improperly or at a temperature outside of the specified range may damage the battery and increase the risk of fire. To ensure maximum battery life, Dyson recommends the following:
    • When not in use the appliance should be stored at room temperature. Recommended range: 18 °C (64° F) to 28 °C (82 ° F).
    • The ambient temperature range for operation and charging should be 10 °C (50 ° F) to 30 °C (86° F).
30. Any servicing must be per formed by Dyson or an authorised service agent using only genuine Dyson replacement parts. This will ensure that the safety of the appliance is maintained. Do not modify or at tempt to repair the appliance.
31. FIRE WARNING – Do not place this appliance on or near a cooker or any other hot sur face and do not incinerate this appliance even if it is severely damaged. The battery might catch fire or explode.
32. FIRE WARNING – Do not apply any fragrance or scented product to the filter(s) of this appliance. The chemicals in such products are known to be flammable and can cause the appliance to catch fire.

Additional information

Charging and storing

• This machine will switch off if the battery temperature is below 10 °C (50°F ). This is designed to protect the motor and battery. Do not charge the machine and then move it to an area with a temperature below 10°C (50°F ) for storage purposes.
• To help prolong battery life, avoid recharging immediately after a full discharge. Allow to cool for a few minutes .
• Avoid using the machine with the battery flush to a surface. This will help it run cooler and prolong battery run time and life.

Battery safety instructions

• If the battery needs replacing, use only Dyson batteries Port Number  398857-01.
• Use only the Dyson charger Part Number 311200 for charging this Dyson machine.

CAUTION
The battery used in this machine may present a risk of fire or chemical burn if mistreated.
Do not short contacts, heat above 60°C {140°F), or incinerate. Keep away from children.
Do not disassemble and do not dispose of in fire.

Changing your battery
Where you hove additional batteries, we recommend that you alternate the batteries to maintain even performance.

To remove a battery
Hold your hand under the battery to support it.
Press the battery release button and slide the battery off the handle.
Place the battery on charge.

To install a battery
Slide the battery onto the handle until it clicks securely in place.

Disposal information

• Dyson products ore made from high grade recyclable materials. Recycle where possible.
  – The battery should be removed from the machine before disposal.
  – When removing the battery, ensure the machine is powered off.
• Safely dispose of or recycle the battery in accordance with local ordinances or regulations.
• Dispose of the exhausted filter unit in accordance with local ordinances or regulations.

Dyson customer care

Thank you for choosing to buy o Dyson machine After registering your two years guarantee, your Dyson machine will be covered for ports and labour (excluding filters) for two years from the date of purchase, subject to the terms of the guarantee.
However, indispensable legal rights of the final consumer under applicable notional legislation governing the sale of consumer goods ore not affected by the terms of the guarantee. If you have any queries regarding your Dyson machine, visit www.dyson.com/support for online help, general tips and useful information about Dyson.
Alternatively, you con call the Dyson Helpline with your serial number and details of where and when you bought the machine.
If your Dyson machine needs o repair, call the Dyson Helpline so we con discuss the available options. If your Dyson machine is under guarantee, and the repair is covered, it will be repaired at no cost.

Limited 2-year guarantee

Terms and conditions of the Dyson 2-yeor limited guarantee

What is covered

• The repair or replacement of your Dyson machine (at Dyson’s discretion) if it is found to be defective due to faulty materials, workmanship or-function within two years of purchase or delivery (if any port is no longer available or out of manufacture, Dyson will replace it with a functional replacement port).
• This guarantee will only be valid if the machine is used in the country in which it was sold.

What is not covered

Dyson does not guarantee the repair or replacement of a machine where a defect is the result of:

• Accidental damage, faults caused by negligent use or care, misuse, neglect, careless operation or hand ling of the machine which is not in accordance with the Dyson User manual.
• Use of the machine for anything other than normo I domestic household purposes.
• Use of ports not assembled or installed in occorda nee with the instructions of Dyson.
• Use of parts and accessories which are not genuine Dyson components.
• Faulty installation (except where installed by Dyson).
• Repairs or alterations carried out by parties other than Dyson or its authorised agents.
• Blockages – refer lo the Dyson User manual for details on how to look for and clear blockages.
• Normal wear and tear (e.g. fuse, brush bar etc.).
• Use of the machine on rubble, ash, plaster.
• Reduction in battery discharge time due lo battery age or use (where applicable).
  If you ore in any doubt as to what is covered by your guarantee, please contact Dyson.

Summary of cover

• The guarantee becomes effective from the dote of purchase {or the dote of delivery if this is later).
• You must provide proof of (both the original and a ny subsequent} purchase/ delivery before any work con be carried out on your Dyson machine. Without this p roof, a ny work carried out will be chargeable. Keep your receipt or delivery note.
• All work will be carried out by Dyson or its authorised agents.
• Any ports which ore replaced by Dyson will become the property of Dyson.
• The repair or replacement of your Dyson machine under guarantee will not extend the period of guarantee.
• The guarantee provides benefits which ore additional to a nd do not affect your statutory rights as o consumer.

Important data protection information

When registering your Dyson machine:

• You will need to provide us with basic contact information to register your machine and enable us to support your guarantee.
• When you register, you will hove the opportunity to choose whether you would like to receive communications from us. If you option to communications from Dyson, we will send you details of special offers and news of our latest innovations.
• We never sell your information to third parties and only use information that you shore with us as defined by our privacy policies which ore available on our website at privacy.dyson.com.

dyson Airblade Wash Dry Instructions

TECHNICAL SPECIFICATION

Tap dimensions
WD04 Height 159 mm Width 303 mm Depth 286 mm
Motor bucket dimensions
WD04 Height 266 mm Width 142 mm Depth 189 mm
Minimum clearance
Z 100 mm clearance from floor

Tap dimensions
WD06 Length 312 mm Width 303 mm
Motor bucket dimensions
WD06 Height 266 mm Width 142 mm Depth 189 mm
Minimum clearance
Suggested installation height 955 mm from finished floor to centre of tap, depending on height of basin. Check installation guide for further details.

WD06 Wall installation

The Dyson Airblade Wash+Dry hand dryer is designed so that the motor unit is located behind the stud wall within a metal enclosure which is supplied with the Dyson Airblade Wash+Dry hand dryer (Fig.1). The vertical wall studs must be constructed so as to allow the metal enclosure to be fitted between them (Fig.2). One of the horizontal wall studs must be fitted a) so it holds the main weight of the metal duct and the unit, and b) so it is in the correct position for the tap stem.
For complete instructions, please refer to the printed installation guide supplied with the machine.
It’s also available online at www.dyson.co.uk/docs

 Fig.1

Fig.2

Install plasterboard.

Fig .3

Install Dyson Airblade Wash+Dry hand dryer

Fig .4

Electrical
Input voltage/Frequency: 200-240V 50-60Hz
Motor specification: 1000W digital brushless motor
Operating temperature range: 0°-40°C, 32°– 104°F
Heater type: None
Standby power consumption: Less than 0.5 W

Construction
Tap construction: Stainless steel (brushed)
Under counter motor assembly construction: Moulded ABS (main unit)
Exterior screw type: Torx T15
Water ingress protection to IP35

Filter
HEPA filter (glass fibre and fleece prelayer)
Captures 99.95% of particles the size of bacteria from the washroom air

Operation
Touch-free infra-red activation
Hand dry time measurement: 14 seconds
Operation lock-out period: 30 seconds
Airspeed at apertures: 341 mph / 549 km/h
Maximum altitude: 2,000 metres / 6,562 ft.

Water operation
Water flow rate: 1.9 l/min normal fitted aerator.
4 l/min with low flow aerator supplied with product.
Water temperature control: Thermostatic mixer recommended (not supplied)
Water pressure required: 1-8 bar
Equipped with automatic duty flush – every 24 hours for 60 seconds after the last use.

Logistics
Net weight: WD04 4.26 kg; WD05 4.54 kg; WD06 9.51 kg
Packaged weight: WD04 6.76 kg; WD05 7.38 kg; WD06 13.65 kg
Packaged dimensions: WD04 H303 × W284 × D291 mm
WD05 H434 × W275 × D288 mm; WD06 H610 × W375 × D302 mm

Basin specification
The Dyson Airblade Wash+Dry hand dryer is compatible with most basin types. Ensure plugs are not installed in the basins and avoid inserts with embedded plugs (e.g. ones that swivel or elevate).
Using a specially designed test method, Dyson engineers evaluated the user experience of a wide range of basin types when used with the Dyson Airblade Wash+Dry hand dryer. For further details on our recommended basins, please see the guide on our website dyson.co.uk/docs
We recommend avoiding basins with the following geometric characteristics:
Flat bases immediately surrounding the drain hole (nominally within a 60 mm radius).
Sloping back and front wall transitions in relation to the base of the basin.
See our pre-installation guide for further details: dyson.co.uk/docs
Basin dimensions:
All basin measurements are internal unless stated otherwise.
Minimum width of basin: 350 mm, Front to back – Minimum: 300 mm
Minimum depth of basin: 100 mm
Maximum depth of basin for WD05 only: 200 mm (External measurement of vessel basin)
Basin materials: Basins with highly polished surfaces should be avoided, e.g. reflective chrome. Porcelain or brushed metal is ideal. When multiple taps are installed side-by-side, tap centres should be a minimum of 580 mm apart.

Standard guarantee
5 year parts, 5 year labour.

Product range

WD04 Short                       WD05 Tall                         WD06 Wall

Further documents are available online to download.

Pre-installation guide.
Installation guide.
Dyson Airblade Wash+Dry hand dryer brochure.
Cleaning guide.
CAD drawings.
Installation videos.

The Carbon label is a trademark of the Carbon Trust.
HACCP International non-food certification mark is the registered trademark of HACCP International.
HACCP International have certified Dyson products based on their recommended installation and operating conditions. Licensed by Dyson. Quiet Mark is a trade mark of the Noise Abatement Society.

For further information please contact Dyson.
0800 345 7788
www.dyson.co.uk

Contents

• Assembling your machine
• Getting started
• Connecting to the Dyson Link app
• Connecting to your smart home
• Power and continuous monitoring
• Information menu
• Auto mode
• Airflow speed and direction
• Oscillation
• Night mode
• Sleep timer
• Heating and Cooling modes
• Changing your HEPA+Carbon filter
• Resetting your HEPA+Carbon filter life
• Changing your HEPA and carbon filters
• Resetting your HEPA and carbon filter life
• Changing your HEPA+Carbon filters with a catalytic filter
• Resetting your HEPA+Carbon filter life
• Looking after your machine

Assembling your machine

• Use both hands to lift your machine out of the box, by its base.
• Do not lift out by the loop amplifier.
• Assemble your machine with the filters that are supplied.
• Dyson Purifier Hot+Cool
• Supplied with a HEPA+Carbon filter.
• Push your HEPA+Carbon filter into the outer cover and position onto the base. Push firmly until both outer covers click securely into place.

Dyson Purifier Hot+Cool
Supplied with separate HEPA and carbon filters.

Push the carbon filters into place on the machine.

Push the HEPA filter into the outer cover. Put the outer covers into position on the base and push firmly until they both click securely into place.

Dyson Purifier Hot+Cool Formaldehyde
Your machine comes with a permanent catalytic filter and a HEPA+Carbon filter.

Push the catalytic filter into position on the machine.

Push the HEPA+Carbon filter into the outer cover and position on the base.
Push firmly until both outer covers click into place.

Getting Started

Connecting to the Dyson Link app

Take full control with the Dyson Link app and access step-by-step setup and support, control how and when your Dyson purifying fan heater operates, monitor air quality with visual updates and automatically keep up to date with the latest software updates.

Download the Dyson Link app from the App Store or Google Play.
Open the app and follow the on-screen instructions to create a new account.

The Android robot is reproduced or modified from work created and shared by Google and used according to terms described in the Creative Commons 3.0 Attribution License.

Connecting to your smart home

Using Amazon Alexa
Ask Alexa to enable the Dyson skill, to control your Dyson purifier or purifier humidifier. And set a routine that automates how your machine works with other devices in your home.

Using Google Assistant
Control all of your connected purifiers with Google or set a routine to automate how your machine works with other devices in your home. Just say “Hey Google” to get started.

Using Siri
Connect your Dyson machines to Siri Shortcuts and you’ll be able to control them with your voice, on your Apple device.

Power and continuous monitoring

Standby on/off
Press the Standby on/off button on your Dyson purifying fan heater or remote control to stop your machine. It will continue to monitor the air quality.

Continuous monitoring
Continuous monitoring is turned off by default. Once turned on, it will always be active until you turn it off again.

With continuous monitoring turned on, your Dyson purifying fan heater will gather air quality, temperature and humidity information, which is displayed on the LCD screen and in the Dyson Link app.

Continuous monitoring
Press and hold the Auto mode button on the remote control for 5 seconds to turn it on. The LCD screen will indicate when continuous monitoring is on or off.

Wi-Fi Connectivity
Wi-Fi is on by default. To turn the Wi-Fi on or off, press and hold the Standby on/off button on your machine for 5 seconds.

Information menu

Press this button to scroll through the information being monitored by your Dyson purifying fan heater.

Information about air quality, temperature, humidity and filter levels is shown on the LCD screen.

When a particular type of pollutant causes air quality to decrease, a symbol for the pollutant will show on the LCD screen.

Auto mode

Set your Dyson purifying fan heater to Auto mode and the on-board sensors will intelligently adjust the settings of the machine according to the air quality.

Air quality: your machine will pause when the target air quality has been reached, switching on again when the air quality levels drop.

Airflow speed: the airflow speed will increase until the target air quality and temperature have been reached.

Airflow speed and direction

Press the Airflow speed button to increase and decrease the airflow speed.
Press the Airflow direction button to change the direction of airflow from front to back.

Change the airflow direction for your personal comfort.

Select the Airflow direction to Fan mode for airflow from the front for purifying, cooling and heating.

Oscillation

Press the Oscillation button to circulate the air around the room and scroll through the oscillation settings from 0° to 350°.

Customize your oscillation setting in the Dyson Link app.

Night mode

In Night mode, your Dyson purifying fan heater will continue to  monitor and respond to changes in air quality, but only using its quietest settings – and with its LCD screen dimmed.

Sleep timer

Your Dyson purifying fan heater will turn off automatically after the selected amount of time.

To set the time: press the button to scroll through the time options. Once activated, press the Sleep timer button once to see the time selected.

To cancel the Sleep timer: press the Sleep timer button twice.

Heating and Cooling modes

Press the button to set the required room temperature.

Your machine will pause when the temperature set has been reached.

Press the Cooling mode button to switch your machine from heating mode to cooling mode.

Before changing your filter, switch off and unplug your Dyson purifier fan heater.

The remaining filter life is displayed on the screen and will indicate when your non-washable filters need replacing. Press the Information button on your remote or check on the Dyson Link app.

You’ll need to reset the filter life on your machine.

Dyson Purifier Hot+Cool Supplied with a HEPA+Carbon filter.

To change your HEPA+Carbon filter, push down on the buttons either side of your machine to release the outer cover. Push down on the tabs to remove the filter.

Push the replacement filter into the outer cover and make sure the tabs click into place.

Put the outer covers into position on your machine and push firmly until they both click securely into position.

Plug in and switch your machine, and reset your filter life.

Resetting your HEPA+Carbon filter life

It’s important to reset your filter life after you have replaced your filter.

Resetting your HEPA+Carbon filter life
Press and hold the Night mode button on your remote control.

The display on your machine will countdown from five, the filter life will be reset and your machine is ready to use.

Changing your HEPA and carbon filters

Before changing your filter, switch off and unplug your Dyson purifier fan heater.

The remaining filter life is displayed on the screen and will indicate when your non-washable filters need replacing. Press the Information button on your remote or check on the Dyson Link app.

You’ll need to reset the filter life on your machine.

Dyson Purifier Hot+Cool
Supplied with separate HEPA and carbon filters.

To change your HEPA filter, push down on the buttons either side of your machine to release the filter covers. Push down on the tabs to remove the HEPA filter.

Push the replacement filter into the outer cover and make sure the tabs click into place.

To change the carbon filter from your machine, remove the filter from the base of your machine and insert the replacement filter.

Put the outer covers into position on your machine and push firmly until they both click securely into position.

Plug in and switch your machine, and reset your filter life.

Resetting your HEPA and carbon filter life

It’s important to reset your filter life after you have replaced your filter.

Resetting your HEPA filter life
Press and hold the Night mode button on your remote control.

The display on your machine will countdown from five, the filter life will be reset and your machine is ready to use.

Resetting your carbon filter life
Press and hold the Oscillation button on your remote control.

The display on your machine will countdown from five, the filter life will be reset and your machine is ready to use.

Changing your HEPA+Carbon filters with a catalytic filter

Before changing your filter, switch off and unplug your Dyson purifier fan heater.
The remaining filter life is displayed on the screen and will indicate when your non-washable filters need replacing. Press the Information button on your remote or check on the Dyson Link app.

You’ll need to reset the filter life on your machine

Dyson Purifier Hot+Cool Formaldehyde
Your machine comes with a permanent catalytic filter and a HEPA+Carbon filter.
You won’t need to change your catalytic filter.
To change your HEPA+Carbon filter, push down on the buttons either side of your machine to release the outer cover. Push down on the tabs to remove the filter.
Push the replacement filter into the outer cover and make sure the tabs click into place.
Put the outer covers into position on your machine and push firmly until they both click securely into position.
Plug in and switch your machine, and reset your filter life.

Resetting your HEPA+Carbon filter life

It’s important to reset your filter life after you have replaced your filter.
Resetting your HEPA+Carbon filter life
Press and hold the Night mode button on your remote control.
The display on your machine will countdown from five, the filter life will be reset and your machine is ready to use.

Looking after your machine

To always get the best performance from your Dyson purifying fan heater, it’s important to regularly clean it and check for blockages.

Cleaning your machine
If your machine is dusty, wipe with a damp lint-free cloth.
Look for blockages in the air inlet holes on the filter and the small aperture inside the loop amplifier.
Use a soft brush to remove dust and debris.
Don’t use detergents or polishes to clean your machine.

Error codes
If your machine shows an error code, try turning it off and then on again.
If this doesn’t clear the error code contact Dyson Customer Care.
For more information and support for your machine go to the Dyson Link app or online: www.dyson.com/support

Dyson Airblade hand dryer

IMPORTANT SAFETY INSTRUCTIONS

BEFORE INSTALLING OR USING THIS APPLIANCE, READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN THE INSTALLATION INSTRUCTIONS AND MAINTENANCE MANUAL.
When using an electrical appliance, basic precautions should always be followed, including the following:

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. This Dyson appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or reasoning capabilities, or lack of experience and knowledge, only if they have been given supervision or instruction by a responsible person concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
2. Before servicing or cleaning the appliance, switch the power off at the service panel. Ensure the switch is locked to prevent the power from being switched on accidentally. If the means of switching off the power cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
3. Do not use sealant when fixing the appliance to the wall.
4. Do not install directly above a heating appliance.
5. The maximum altitude of use is 2,300 meters.
6. The size of the lead wire used for the wiring connection (including grounding lead) shall not be smaller than 18AWG.

• DO NOT USE ANY JETWASH EQUIPMENT FOR CLEANING ON OR NEAR THIS APPLIANCE.
• ALL ELECTRICAL INSTALLATION AND REPAIR WORK SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN OR DYSON FIELD SERVICE ENGINEER IN ACCORDANCE WITH CURRENT LOCAL CODES OR REGULATIONS.
• The appliance should be located indoors. Operating temperature range 0°C (32°F) to 40°C (104°F). To reduce the risk of fire or electric shock, do not expose the internal mechanisms/components of this appliance to moisture.

Tools required

• Suitable screwdriver for wall type fixings
• Small Phillips screwdriver
• Small flat head screwdriver
• Dyson tool (supplied)
• Tape measure and pencil
• Hand drill
• Suitable drill bit
• Pliers/wire strippers
• Knife

Pre-installation checks

Pre-installation planning

• The machine is designed for a dry, internal location only.
• Conformity and compliance is the responsibility of the installer. Consult local and national accessibility codes and regulations for relevant installation guidelines.
• Install the machine in compliance with all building codes and/or regulations.
• Isolate the power supply before installation or service.
• Make sure that no pipework (gas, water, air) or electrical cables, wires or ductwork are located directly behind the drilling/ mounting area.
• Select a location that will allow accessibility to the machine and proper clearance from surroundings and floor.
• Make sure that there are no obstructions between the machine and the floor and at least 210mm above for filter removal.
• Dyson recommends the use of protective clothing, eye wear and materials when installing/repairing as necessary.

Wall fixing requirements

• Do not fix to unsupported plasterboard (drywall) as this will not provide a safe and secure installation for the machine and may also invalidate the guarantee.
• Where only unsupported plasterboard is available for installation, a Dyson backplate must be used. Contact the Dyson Helpline for further information.
• If the wall has an airgap, the fixings use must be of a sufficient length to provide a secure installation.
• Don’t use sealant when fixing the machine to the wall.

Power modes

• This Dyson Airblade™ hand dryer has two power modes, 900W and 650W.
• The machine is set to 900W as default. If required, change the power mode to 650W before installation.
• For more information about the power modes, go to www.dyson.com/airblade

Electrical

• Input voltage/frequency: refer to rating plate.
• Make sure that the power supply is switched off before installing.
• Cable specification: 3 core cable (live/neutral/earth).
• Local electrical regulations must be adhered to when installing or repairing this machine.
• Rated power: refer to rating plate.
• Operating temperature range: 0°C to 40°C.
• Maximum length of strip-back of Live and
• Neutral wire insulation: 7mm.

Quality testing

The Dyson Airblade™ hand dryer has undergone extensive quality testing, to make sure it can withstand forces and impacts typical of a commercial and public bathroom environment.

Installing the Dyson Airblade™ hand dryer

Drill the mounting holes

• Select the installation location and appropriate height.
• Recommended mounting heights are shown on the Mounting template. It may be necessary to adjust the measurements for individual installations.
• Fix the supplied Mounting template to the wall in the correct location.
• Rear cable entry installation: the electricity supply cable must align from the wall to the entry point on the Mounting template.
• Side cable entry installation: an additional hole will need drilling. Refer to the Mounting template for location.
• Drill the holes, where marked, using a suitable drill bit.

For rear cable entry installation

• Unscrew and remove the cable clamp, terminal block and terminal block holder from the backplate. Loosen all three screws on the terminal block, ensuring the preinstalled earth wire remains in place.
• Cut the gland smaller than the diameter of the cable and feed the cable through the conduit box and gland. Don’t remove the gland from the backplate.
• Using suitable fixings (not countersunk screws), fix the backplate to the wall.
• Make sure that the cable sits securely in the cable guide. Any part of the cable not seated securely may prevent the machine from being fixed properly onto the backplate.
• Secure the live, neutral and earth wires to the appropriate terminal block locations, as indicated on the backplate. Ensure the preinstalled earth wire remains securely inserted into the connector block.
• Secure the terminal block to the backplate with the terminal block holder and secure the cable clamp.
• Only clamp double insulated cables with the cable clamp.
• Don’t overtighten any of the electrical fixtures.

For side cable entry installation

• Using suitable fixings (not countersunk screws), fix the backplate to the wall.
• Identify which side the cable will enter.
• Unscrew the entry tab on the machine.
• Cut the rubber side tab of the conduit box on the side that will be facing downwards after installaton.
• Use a suitable cable gland/conduit connector (not supplied) for the installation.
• Secure the conduit box on the wall using suitable fixings.
• Unscrew and remove the cable clamp, terminal block and terminal block holder from the backplate. Loosen all three screws on the terminal block, ensuring the preinstalled earth wire remains in place.
• Cut the gland smaller than the diameter of the cable and feed the cable through the conduit box and gland. Don’t remove the gland from the backplate.
• Make sure that the cable sits securely in the cable guide. Any part of the cable not seated securely may prevent the machine from being fixed properly onto the backplate.
• Secure the live, neutral and earth wires to the appropriate terminal block locations, as indicated on the backplate. Ensure the preinstalled earth wire remains securely inserted into the connector block.
• Secure the terminal block to the backplate with the terminal block holder and secure the cable clamp.
• Only clamp double insulated cables with the cable clamp.
• Don’t overtighten any of the electrical fixtures.

Install the main body

• This Dyson Airblade™ hand dryer has two power modes, 900W and 650W.
• The machine is set to 900W as default. If required, change the power mode to 650W before installation.
• Hook the machine on to the backplate and gently lower the bottom of the machine until it is flush with the wall. Check that both backplate hooks are securely in position before continuing.
• Fix the 2 security screws into the bottom of the machine using the tool supplied.

Complete the installation
Place the filter unit in the machine and make sure it clicks securely into place. Turn on the mains power supply and test the machine is working as it should by placing hands in sight of the sensors.

Maintenance

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1.  This Dyson appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or reasoning capabilities, or lack of experience and knowledge, only if they have been given supervision or instruction by a responsible person concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
2. Do not allow the appliance to be used for any purpose other than drying hands. Use this appliance only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
3. Before servicing or cleaning the appliance, switch the power off at the service panel. Ensure the switch is locked to prevent the power from being switched on accidentally. If the means of switching off the power cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
4. The maximum altitude of use is 2,300 metres.

WARNING

• ALL ELECTRICAL INSTALLATION AND REPAIR WORK SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN OR DYSON FIELD SERVICE ENGINEER IN ACCORDANCE WITH CURRENT LOCAL CODES OR REGULATIONS.
• The appliance should be located indoors. Operating temperature range 0°C (32°F) to 40°C (104°F). To reduce the risk of fire or electric shock, do not expose the internal mechanisms/components of this appliance to moisture.

Looking after your hand dryer

Please register as a Dyson hand dryer owner To help us ensure you receive a prompt and efficient service, please register your machine at www.dyson.com/airblade. This will register your guarantee, confirm ownership of your Dyson machine in the event of an insurance loss, and enable us to contact you if necessary.
You will need your serial number, which can be found on the rating plate inside the main body and on the information sticker on the front of the machine.
Please ensure all instructions and guidance in the Installation instructions and Maintenance manual are adhered to or your guarantee may be invalidated.

Maintenance

How to use
Place your hands beneath the Dyson Airblade™ hand dryer arms and it will start automatically, creating sheets of air that scrape water from your hands.
For best dry time results: Keep your hands flat and parallel to the machine’s surface, approximately 5mm from the air aperture, drawing your hands through the airflow from your wrists to finger tips.
Move your hands slowly through the airflow, keeping a consistent speed (approx. 2.5 seconds per side), alternating between front and back each time. Keep your hands flat, close the gaps between your fingers and keep your thumbs tucked in, so the whole of your hand is drawn through the airflow.
For more information about the power modes, go to www.dyson.com/airblade

Troubleshooting

Hand dryer cuts out
After 30 seconds of continued use the hand dryer will turn off automatically. Remove and replace hands to restart.
Turn the machine off and on again at the mains electricity supply.
Make sure the sensors are clean.
Check the air apertures are clean and free of dust and blockages. If the air apertures are dusty, simply remove dust.
Check that the air inlet is free from blockages.

Dry time has increased
Make sure that the correct power mode has been selected.
Check that the air inlet is free from blockages.
Inspect the air apertures for dust, and remove.

Airflow is running hotter than usual
Check that the air inlet is free from blockages.
Inspect the air apertures for dust, and remove.

Air is continuously running
After 30 seconds of continued use the hand dryer will turn off automatically. Remove and replace hands to restart.
Check that the air inlet is free from blockages. Inspect the air apertures for dust, and remove.
Contact Dyson for further support and information or online at www.dyson.com/airblade

Filter maintenance

Regularly check the air inlet to ensure that it is free from dust and debris. Simply wiping the inlet with a soft cloth should be sufficient to remove dust and debris.
If the air inlet gets clogged, further cleaning or a filter change might be required.
If required for high usage environments, a Dyson filter change kit provides everything needed to change your machine’s HEPA filter on site. Contact the Dyson Helpline for more information.

Filter cleaning or replacement for your hand dryer can be carried out by carefully following the instructions given in the filter change kit. If in any doubt, consult a qualified electrician or contact the Dyson Helpline for support.

Servicing

If your hand dryer needs servicing, please call the Dyson Helpline or visit the website at www.dyson.com/airblade

Additional Information

Disposal information

Dyson products are made from high grade recyclable materials. Recycle where possible.
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

Your guarantee
Terms and conditions of the Dyson 5 year guarantee

• If you have registered your machine online, your guarantee will start from the date of purchase. Please retain your proof of purchase. If you do not have your proof of purchase, your guarantee will start 90 days after the date of manufacture, according to Dyson’s records.
• Where this machine is sold within the EU, this guarantee will only be valid (i) if the machine is installed and used in the country in which it was sold or (ii), if the machine is installed and used in Austria, Belgium, France, Germany, Ireland, Italy, Netherlands, Spain or the United Kingdom and the same model as this machine is sold at the same voltage rating in the relevant country. Where this machine is sold outside of the EU, this guarantee will only be valid if the machine is installed and used in the country in which it was sold.

What is covered

• All factory parts of your hand dryer are guaranteed against original defects, material and workmanship when used in accordance with the Dyson manual for a period of 5 years from the start of your guarantee.
• Please call the Dyson Helpline for more information.
• Where Dyson determines that the main body assembly needs replacing, Dyson will send a replacement to be fitted by the customer on site. The customer will need to return any defective parts to Dyson using the prepaid postage box provided.
• Any replaced parts must be returned to Dyson or an administration fee will be levied.
• Where a filter change is required, Dyson will provide a filter change kit to be installed on site by the customer.
• Any parts which are returned and replaced by Dyson will become the property of Dyson.
• The replacement of any part of your machine under guarantee will not extend the period of guarantee.
• The guarantee provides benefits which are additional to and do not affect any statutory rights you may have as a consumer.

What is not covered

Dyson does not guarantee the repair or replacement of a product as a result of:

• Accidental damage, faults caused by negligent use or care, unintentional or deliberate misuse, neglect, vandalism, careless operation or handling of the machine which is not in accordance with the Dyson manual.
• Use of parts not assembled or installed in accordance with the instructions of Dyson.
• Use of parts and accessories which are not genuine Dyson components.
• Faulty installation, or installation that does not precisely follow the installation instructions supplied by Dyson (except where installed by Dyson).
• Repairs or alterations carried out other than in accordance with instructions by Dyson.
• Damage from external sources such as transit, weather, electrical outages or power surges.
• Normal wear and tear (e.g. fuse, etc.).
• Damage caused by cleaning which is not in line with the instructions in the manual.
• Damage caused by water ingress due to cleaning or treatment prohibited in the manual.
• Any electrical, flooding or structural damage, or any loss of business or revenue as a result of product failure.
  If you are in any doubt as to what is covered by your guarantee, please contact Dyson.

Summary of cover

• You must provide proof of (both the original and any subsequent) delivery/ purchase before any work can be carried out on your Dyson machine or before any replacement parts will be supplied. Without this proof, any work carried out or parts supplied will be chargeable. Keep your receipt or delivery note.
• Subject to the exclusions above, all work to be carried out under this guarantee will be carried out by Dyson or its authorised agents.

Important data protection information when registering your Dyson machine:

• You will need to provide us with basic contact information to register your machine and enable us to support your guarantee.
• When you register, you will have the opportunity to choose whether you would like to receive communications from us. If you opt-in to communications from Dyson, we will send you details of special offers and news of our latest innovations.
• We never sell your information to third parties and only use information that you share with us as defined by our privacy policies which are available on our website: privacy.dyson.com

To achieve enhanced styling with less reliance on heat, Dyson engineers developed flexing plates. Made from materials selected for their flexibility,
strength and thermal conduction, they shape to gather and control hair.

Explore www.dyson.com/mycorrale to:

– Discover styling tips and guides
– Learn about your machine’s features
– Activate your 2-year warranty.

Getting the most

from your warranty
We don’t stop caring about our machines once they’re yours. Even when your warranty has ended, we’ll still be on hand to help.

Exclusive owner benefits

– Free Dyson parts and labor
– Hassle-free replacement
– Expert advice. 7 days a week.
– Styling tips and guides.
To activate your warranty, you’ll need your serial number, which can be found on the battery pack label.
Go to: www.dyson.com/your-dyson or reach out to our helpline at 866-277-5122

In the box

   Dyson CorraleTM        Heat-resistant travel                        Charging dock              Magnetic 360°
         straightener       pouch and Flight-ready tag protector                                          charging cable

Controls

Using your straightener

Getting started
Before using your Dyson Corrale™ straightener for the first time, remove the Flight-ready tag from any packaging.
Insert the Flight-ready tag into your straightener.
Fully charge your straightener before first use.
For the best styling results, make sure your hair is dry and tangle-free.

Turning on

Slide the Lock button to open your straightener. Press and hold the Power button until a battery icon appears on
the OLED screen. Press the Temperature (+) button to select the temperature you want The Power button will pulse red as your straightener heats up. Your straightener is ready
to use when the Power button illuminates red, a prompt sounds and a tick icon appears on the OLED screen

Adjusting the temperature

Press the Temperature (+/-) control buttons to select the temperature that suits your hair type and styling preference.
Your straightener has three settings, to enable you to style at lower temperatures.
Go to www.dyson.com/mycorrale for styling tips and guides.
The temperature will appear on the OLED screen as it heats up or cools down and the Power button will pulse until the selected temperature has been reached.

Turning off

Press and hold the Power button until the OLED screen turns off. Close your straightener and slide the Lock button to close.
The Power button will pulse until the flexing plates have cooled. If you close your straightener without turning the power off, it will turn off automatically.

Traveling with your straightener

Getting ready to fly

The Dyson Corrale™ straightener is designed to meet ICAO regulations, allowing you to carry it on board an aircraft

Before flying

1. Contact your airline in advance to inform them about the Flightready feature.
2. Remove the Flight-ready tag before airport security and leave disconnected throughout the flight.
3. S tore your straightener in your hand luggage. Please note: Regulations in Japan mean you will not be able to fly in or out of any Japanese airports with your straightener.
   For more information about being flight-ready go to www.dyson.com/mycorrale.

When the Flight-ready tag is removed, all controls will be disabled. If you try to use your straightener when flight-ready, an airplane icon will appear on the OLED screen.
If the airplane symbol does not appear on the OLED screen when the Flight-ready tag is removed, contact Dyson before traveling. Place the Flight-ready tag in the
Flight-ready tag protector to prevent damage to the tag and straightener.

Charging when traveling

Just check if you need a travel adaptor. The Magnetic 360° charging cable is suitable for use with all mains electricity supplies.

Reactivating your straightener

Insert the Flight-ready tag back into your straightener

Assembling the charging dock

Your dock can be used as a charging dock or a stand to store your Dyson Corrale™ straightener. Push the two parts of the charging dock together until
they click securely in place. Connect the Magnetic 360° charging cable to the base of the charging dock.

Charging your straightener

For best performance, place your Dyson Corrale straightener in the dock when not in use and in between sections to extend run time. Always begin with 100% charge before styling.
When your straightener needs charging, the battery icon on the OLED screen will flash and a prompt will sound.
When the battery is empty, the battery icon will flash and a prompt will sound five seconds before your straightener turns off.
The battery charging LED will be amber when charging and turn green when fully charged. Charge your Dyson Corrale™ straightener on the dock or directly with the Magnetic 360° charging cableIf your straightener is turned off, a prompt will sound when you connect to the Magnetic 360° charging cable.
Charging dock Place your Dyson Corrale straightener in the dock when not in use and in between sections to extend run time. Always begin with 100% charge before styling.

Turning the prompt sounds on and off You can mute the prompt sounds during active use. For your safety, you won’t be able to mute the sounds for Sleep mode or alerts. Press and hold the Power and
Temperature (–) buttons to turn the prompt sounds off.

Changing temperature units You can select your preferred temperature units (Centigrade or Fahrenheit).
Press and hold the Power and Temperature (+) buttons to change between units.
When your preferred temperature unit shows on the OLED screen, release the buttons.

Looking after your straightener

Turn off your Dyson Corrale™ straightener and leave to cool before cleaning. Clean the flexing plates with a damp, lint-free cloth. Rub gently to remove any stubborn hair product residue.
Don’t use chemicals or abrasive products as this may damage the surface of the flexing plates

Alert screens

Too hot Turn your straightener off  and leave to cool down

Reset Charge your straightener to 100% then turn it off then back on again to reset.

Charger error The charger isn’t working as it should. Please contact the Dyson helpline.

If the airplane symbol doesn’t appear on the OLED screen when the Flight-ready tag is removed,
contact Dyson before traveling

Too hot Turn your straightener off and leave to cool down.

User manual
Dyson V15 detect

Top view of the Dyson V15 detect machine, showing the cleaner head, wand, bin, and main body.

In the box

A vacuum cleaner with a click-in battery	Laser Slim Fluffy™ cleaner head A precisely-angled laser makes invisible dust visible on hard floors.	High torque cleaner head with an anti-tangle comb Dyson DLS™ technology monitors brush bar resistance and adapt power across different floor types. Polycarbonate teeth prevent tangling around the bristles.

Additional click-in battery

Additional click-in batteries included with V15 Detect Absolute and V15 Detect Complete or can be purchased separately from www.dysoncanada.ca

Wand	Charger Charges your vacuum with or without a dock.	Wall dock Your Dyson vacuum drops into the wall-mounted charging dock, ready for your next clean.

Some tools may not be included.
You can buy additional tools at www.dysoncanada.ca

Combination tool Two tools in one – wide nozzle and brush, for quick switching between cleaning and dusting tasks around your home or car.	Crevice tool Engineered for precise cleaning around tricky edges and into hard-to-reach narrow spaces.	Hair screw tool Anti-tangle conical brush bar spirals hair off and into the bin. Motor-riven cleaning for smaller spaces.	Light pipe crevice tool with LED lights lets you reach into dark, narrow spaces and see where you’re leaning.	Soft dusting brush Enclosed is a skirt of soft nylon bristles or gentle, a vacuum-assisted dusting of delicate objects and surfaces.

Stubborn dirt brush Stiff nylon bristles dislodge ground-in dirt from coarse carpets, high traffic areas, and car interiors.	Wand clip Clips to your vacuum wand to hold tools.

Getting started

Power modes

Your machine has three power modes for different tasks. Change power modes quickly using a single button.

Eco-mode

The screen shows the machine set to Eco mode with a full battery in green to show that this will give the longest battery life of the three modes.
Maximum run time for longer cleans all-around your home.

Auto and Med mode

Two screens show the machine set to Auto mode and Med mode with a blue battery showing that this will give a medium length of battery life.
The optimum balance of power and run time.
Attach your cleaner head or Hair screw tool to activate the Auto mode. Suction power automatically adapts to dust levels.

Boost mode

The screen shows the machine set to Boost mode with a red battery to show that this will give the shortest battery life of the three modes.
Designed for intensive spot cleaning of ground–in dirt

Arrow showing the end of the wand connecting to the cleaner head.
Turn your laser on and off
Turn your laser on or off with the slider switch on your cleaner head.

Class 1 laser product – safe for pets and humans.
Avoid looking directly into the beam.

The screen, on the end of the main body, shows a graph of the sizing and counting of the dust particles.

Measures microscopic dust particles

A piezo sensor continuously sizes and counts dust particles at the inlet.
Attach your cleaner head or Hair screw tool and use in Auto mode to automatically increase suction power when needed.

The LCD screen

The LCD screen shows your particle count information and performance, including the cleaning mode selected, remaining run time, filter maintenance, and blockage information.

Settings menu
Control the settings on your machine using the button.
To enter the settings menu, press and hold the button until the menu screen appears. Tap to scroll through the options available.

Particle count and graph
Select to turn the measuring and counting of particles on and off. Turn off the measuring and counting of particles to stop your machine from automatically adjusting suction power and turn off the graph.

Automatic adjustment between hard floors and carpets will continue when using the High Torque cleaner head.

Adjust reactive suction power sensitivity.
Use the selection button to change how sensitive the particle count is.
This will change how your machine automatically reacts to the dust particles.

For more information and support for your machine go online: www.dysoncanada.ca/support

Change language

To change the language on your screen, press the button and hold until the language list appears. Release the button.
Tap the button to scroll through the language list to your preferred language.
Press and hold the button until the countdown ends.
A green tick will appear on the screen to show your language selection is complete.
To cancel your selection, release the button during the countdown.

Change alert settings

You can turn the alert motor pulse off. Your motor will no longer pulse but run time alert information will continue to be displayed on the LCD screen when your machine needs your attention.
Turning off alerts will not turn off the blockage alert pulsing. This is to ensure you clear any blockages, preventing damage to your machine.
Tap to scroll through the settings menu. Select the ‘Alerts’ option.
Scroll to select on or off. Hold the button until the countdown ends and a tick appears on the screen. To cancel your selection, release the button during the countdown

Run time countdown

When the battery needs charging, your machine will pulse three times and a low run time icon will appear on the screen.
When your battery is empty, a red warning icon will appear on the screen.
When the Particle count and graph are turned on, the low run time will be in amber and red when in Boost mode.

Battery health

To get the best performance and life from your battery, use Eco or Auto/Med mode.

Alerts
The alerts you might see are:

Filter – the filter isn’t fitted correctly or needs cleaning.
Blockage – your machine has a blockage that needs removing.

Exit settings menu

Charging your machine

It’s important to fully charge your new machine before using it for the first time and after every clean. This is because the battery and monitoring system’s algorithm ‘learns’  over time, and fully charging your machine helps it to more accurately calculate and display the remaining run time.

Connect to the charger either directly or in the dock.
The blue LEDs on either side of the battery will flash during charging.
When the battery is fully charged, both LEDs will light for 5 seconds.
Your battery is fully charged when the display shows 100%.
Your machine won’t operate or charge if the ambient temperature is below 5°C(41°F). This is designed to protect both the motor and battery.

Changing your click-in battery

If you have additional click-in batteries, we recommend that you alternate the batteries to maintain even performance.
Additional click-in batteries included with V15 Detect Absolute and V15 Detect Complete or can be purchased separately from www.dysoncanada.ca

Removing your battery
Push the battery release button on the handle and slide the battery off your machine.
Charge the battery.

Refitting your battery
Align your battery with the handle and slide it in. Push firmly until it clicks into place.

Caring for your floors

Check that the underside of the cleaner head or tool is clean and free from any objects that may cause damage.
Before vacuuming your flooring, rugs, and carpets, check the manufacturer’s recommended cleaning instructions.
The brush bar on your machine can damage certain carpet types and floors.
Some carpets will fuzz if a rotating brush bar is used when vacuuming. If this happens, we recommend vacuuming without the motorized floor tool and consulting with your flooring manufacturer.

Emptying your bin

Empty as soon as the dirt reaches the MAX level – don’t overfill. Using your machine, when the dirt is above the MAX line, may affect the performance and require more frequent filter washing.
Overfilling your bin could result in inaccurate readings on the particle graph.

Remove your wand

Press the red wand release button, on the top of the wand, and pull the wand away from the bin.

Release the dirt
Hold the machine over the bin, pointing downwards.
Firmly push the red bin release button. The bin will slide down, cleaning the shroud as it goes, and the bin base will open.
The bin base won’t open if the red bin release button isn’t pushed down all the way.

Minimize dust contact
Cover your bin tightly in a dust-proof bag while you empty. Remove the bin carefully, seal the bag tightly and dispose of.

Close your bin
Push the bin base upwards until the bin and bin base click into place.

Cleaning your bin

Remove your bin

If it is necessary to clean your bin, empty it as shown in the ‘Emptying your bin’ section.
Press the red button located on the bin runner to release the bin and slide your bin off the runner.
Only clean your bin with a damp cloth.
Make sure that the bin and seals are completely dry before replacing.

Refit your bin
Insert the spine onto the bin runner.
Close your bin by pushing the bin base upwards until the bin and bin base click into place.
Your bin isn’t dishwasher safe and the use of detergents, polishes, or air fresheners to clean your bin isn’t recommended, as it may damage your machine.

Clearing blockages

Disconnect your machine from the charger before looking for blockages.
Be careful not to touch the trigger and be aware of sharp objects.
Leave your machine to cool down before looking for blockages.
Don’t use your machine when looking for blockages as this could cause injury.
If your machine detects a blockage, the motor will pulse and you won’t be able to use your machine until the blockage has been cleared.
If you try to use your machine when the motor is pulsing, it will automatically cut out.

Check the main body

Remove the bin and check for blockages in the main body of your machine.
Make sure any blockages are completely cleared and all parts are fitted
before using your machine.

Check the wand and cleaner head
Check the wand for blockages.
Check your cleaner head for blockages, following the instructions to remove
the brush bar, where necessary.

Reassemble your machine
Refit all parts securely before using your machine.
Clearing blockages isn’t covered by your warranty.

Wash your filter at least once a month to maintain optimum suction power.
For more information and support for your machine go online: www.dysoncanada.ca/support
Important: your filter must be completely dry before you put it back into the machine. Your machine could be damaged if used with a damp filter.

Twist off your filter
Twist your filter counter-clockwise and pull it away from your machine.

Tap your filter
Before washing your filter, tap it gently over a bin to remove any loose dust and debris.

Wash your filter
Wash with warm, running tap water – gently rub your filter with your fingers to remove the dirt.

Fill and shake
Place your hand over one end of your filter.
Fill the filter with warm tap water.
Place your hand over the open end of the filter and shake it firmly to remove trapped dirt and debris.

Shake out the water
Empty the filter and shake firmly to remove excess water.
Shake with the filter in both an upward and downward position.
Keep shaking until there’s no water coming from the filter.

Dry your filter

Leave your filter to dry for at least 24 hours in a well-ventilated, warm place.
Don’t dry your filter in a tumble dryer, microwave, or near a naked flame.
Important: your filter must be completely dry before you put it back into the machine. Your machine could be damaged if used with a damp filter.

Washing your Laser Slim Fluffy™ brush bar

Your Laser Slim Fluffy™ cleaner head has a washable brush bar. To maintain optimum performance, check and wash your brush bar regularly.
Make sure your machine is disconnected from the charger and take care not to touch the trigger.

Remove your brush bar

Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.
Press the cleaner head release button on the end of the wand. Place the cleaner head upside down.
Push the end cap up fully and pull the brush bar out of the cleaner head.

Wash and dry your brush bar

Hold your brush bar under running water and gently rub to remove any lint or dirt.
Stand your brush bar upright as shown. Leave to dry completely for at least 24 hours.

Replace your brush bar

Before replacing, check that your brush bar is completely dry.
Reattach the end cap to your brush bar.
Slide your brush bar into the cleaner head. Push the end cap back down to the closed position.

Cleaning your laser lens
To maintain optimum performance, keep your laser lens clean. Only clean the lens when the cleaner head is not attached to your machine.
Use a soft, dry, lint-free cloth to wipe the lens.

Clearing obstructions from your High Torque cleaner head with an anti-tangle comb

Your High Torque cleaner head with an anti-tangle comb doesn‘t have a washable brush bar. To maintain optimum performance, check your brush bar regularly and clear any obstructions.
Make sure your machine is disconnected from the charger and take care not to touch the trigger.

Remove your brush bar

Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.
Press the cleaner head release button on the end of the wand. Place the cleaner head upside down.
Use a coin to unlock the end cap.
Twist the end cap and remove it from your brush bar. Don’t wash the end cap.
Slide your brush bar out of the cleaner head.

Look for obstructions

Clear any debris from your brush bar.
Check inside the cleaner head and remove any debris or blockages.
Your High Torque cleaner head and brushbar aren’t washable. Wipe over with a damp lint-free cloth.
Don’t put any part of your machine in a dishwasher or use detergents, polishes, or air fresheners.

Replace your brush bar

Push the end cap back onto your brush bar and slide it back into the cleaner head.
Turn the end cap into the locked position.
Your cleaner head isn’t washable and should only be wiped over with a damp lint-free cloth.

Cleaning your tools

Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.
Wipe with a damp, lint-free cloth, without touching the connector end.
Make sure your tools are completely dry before using.

Clearing blockages from your Hair screw tool

Your Hair screw tool doesn’t have a washable brush bar. To maintain optimum performance, check your brush bar regularly and clear any obstructions.
Make sure your machine is disconnected from the charger and take care not to touch the trigger.

Remove the cover and brush bar

Remove the Hair screw tool from the wand or machine.
Push the base plate open. Press the red lever down to release the cleaner headcover.
Pull the cleaner headcover off the main body of the tool.

Look for obstructions.

Pull your brush bar firmly to remove it from the main body.
Check and remove any obstructions from all three parts of your Hair screw tool.
Your Hair screw tool isn’t washable. Wipe over with a damp lint-free cloth.
Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.

Reassemble Hair screw tool

Put your brush bar back into position and press firmly until it clicks back into position.
Check the red locking lever is in the unlocked position. Align the cleaner headcover with the guide on the main body. Push it down until it clicks into position.
Push the red locking lever up until it clicks into position and push the base plate back into place.

Looking after your machine

To always get the best performance from your machine, it’s important to clean it regularly and check for blockages.

Look after your machine
If your machine is dusty, wipe with a damp lint-free cloth.
Check for blockages in the cleaner head, tools, and main body of your machine.
Wash your filter regularly and leave it to dry completely.
Don’t use detergents or polishes to clean your machine.

Look after your battery
To get the best performance and life from your battery, use Eco or Auto/Med mode.
Your machine won’t operate or charge if the ambient temperature is below 5°C(41°F).
This is designed to protect both the motor and battery.

Your serial numbers
You can find your serial numbers on your machine, battery, and charger.
Use your serial number to register.
For more information and support for your machine go online: www.dysoncanada.ca/support

SV12 JN.00000 PN.000000-00-0000.00.00 VERSION NO.01

REGISTER TODAY
3 easy ways to register your 2-year limited warranty.

IMPORTANT SAFETY INSTRUCTIONS
WHEN USING ELECTRICAL MACHINES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO PERSONS INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.

WARNING
THE MACHINE AND THE REMOTE CONTROL BOTH CONTAIN MAGNETS.

1. Pacemakers and defibrillators may be affected by strong magnetic fields. If you or someone in your household has a pacemaker or defibrillator, avoid placing the remote control in a pocket or near to the device.
2. Credit cards and electronic storage media may also be affected by magnets and should be kept away from the remote control and the top of the machine.
   TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:
3. This Dyson machine is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction by a responsible person concerning the use of the machine to ensure that they can use it safely.
4. Do not allow it to be used as a toy. Close attention is necessary when used by or near children. Children should be supervised to ensure that they do not play with the machine.
5. Always plug this machine directly into a wall outlet/receptacle. Never use an extension cord or relocatable power tap (outlet/power strip).
6. This machine must not be located immediately below a socket outlet.
7. If there is a loose fit between the plug and the outlet or the plug becomes very hot, the outlet may need to be replaced. Check with a qualified electrician to replace the outlet.
8. CAUTION – Risk of electric shock, do not open the machine, and no user-serviceable parts inside.
9. This machine is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. When moving the machine, hold it by the base and not the air loop amplifier. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the machine and keep them away from the sides and rear.
10. This machine has hot parts inside. Do not use it in areas where petrol, paint, or flammable liquids are used or stored or where their vapors are present.
11. Extreme caution is necessary when any machine is used by or near children or infirm persons and whenever it is left operating and unattended.
12. Do not operate any machine with a damaged cord or plug or after the machine malfunctions, or has been dropped or damaged in any manner. Discard the machine, or return it to an authorized service facility for examination and/or repair.
13. Do not run the cord under the carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not route the cord under furniture or machines. Arrange the cord away from traffic areas and where it will not be tripped over.
14. To avoid a tripping hazard, wind the cord when not in use.
15. This machine is not intended for use in bathrooms, laundry areas, and similar indoor locations. Never locate the machine where it may fall into a bathtub or other water containers. Do not store this machine in the immediate surroundings of a bath, shower, or swimming pool.
16. WARNING: In order to avoid overheating, do not cover the machine.
17. To prevent a possible fire, do not block air intakes or exhausts in any manner. Do not use it on soft surfaces, like a bed, where openings may become blocked.
18. Use this machine only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
19. Do not use this machine if it has been dropped or if it has visible signs of damage.
20. Always use this appliance on a horizontal and stable surface.
21. Do not use it outdoors or on wet surfaces and do not handle any part of the machine or plug with wet hands.
22. Keep this machine and cord away from heated surfaces. Do not position the cord under the furniture or machines.
23. If the supply cord is damaged, it must be replaced or repaired by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
24. Do not use this machine if it has been damaged or submerged in water.
25. Do not put any objects into any opening as this may cause an electric shock or fire, or may damage the machine.
26. Disconnect power or unplug before cleaning, performing any maintenance or replacing a filter. Always unplug the machine when not in use.
27. Chemical Burn and Choking Hazard. Keep batteries away from children. This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Even used batteries may cause injury. POLARIZATION INSTRUCTIONS
28. To reduce the risk of electric shock, this machine has a polarized plug (one blade is wider than the other) as a safety feature. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not attempt to defeat this safety feature and do not change the plug in any way.
    SAVE THESE INSTRUCTIONS

• Each time the heating mode is selected, it conducts a short calibration cycle. Airflow will be automatically controlled during this cycle. Once the calibration cycle is complete, it will revert to the selected airflow speed. On first use, the machine will default to a temperature 3°C higher than the detected room temperature.
• Thereafter, the machine will remember the last target temperature set.
• Select the desired room temperature using the Thermostat control button. Press the large red button on the remote control to increase the target temperature by 1°C; press the small red button on the remote control to decrease it by 1°C. The machine will not operate in heating mode unless the target temperature is above room temperature.

Remote control

Remote control docks magnetically
Attach the remote control to the top of the machine with the buttons facing down.

Airflow speed control

Press the red Thermostat control button until the digital display shows the target room temperature. The power button light will change from blue to red to indicate that you have entered the heating mode. The heating symbol will be red while heating and will change to white when the target room temperature has been reached. Once the target room temperature has been reached, the machine will stop heating the air. If the room temperature falls below the target temperature, the machine will start to heat again. The red circle surrounding the power button remains on when the machine is in heating mode. To adjust the airflow speed, use the airflow control button.

Press the blue Cooling mode button to enter cooling mode. The power button light will change from red to blue to indicate that you have entered the cooling mode. To adjust the airflow speed, use the airflow control button.

Sleep timer

Tilt function

• To set the sleep timer, select the desired time. When the time reaches zero, the machine will go into standby mode. To cancel, increase the time until two dashes appear.
• When using the sleep timer, the LED display will turn off after 10 seconds of inactivity.
• Carefully hold the base and the main body. Tilt the loop amplifier forward or backward for the required airflow angle.

Diffused and Focused modes

Diffused mode
Press the wide-angle button to change from a personally directed airflow to a whole room airflow. Heating and cooling modes work in this mode.

Oscillation and Airflow speed control

Oscillation control
To start the machine oscillating, Press the Oscillation control button. To stop the machine from oscillating, press it again. The machine will not oscillate when the control buttons are pressed

Focused mode
Press the narrow-angle button to change from a whole room airflow to a personally directed airflow. Heating and cooling modes work in this mode.

Airflow speed control
To change the airflow speed, press the Airflow speed control button. The digital display will show the new fan speed. If in heating mode, after 3 seconds it will change back to displaying the target temperature

Cleaning

Unplug from the main power source. If the machine has been in use, leave it for 1 to 2 hours before cleaning to allow the machine to cool completely. Dust may accumulate on the surface of the machine. Wipe dust from the loop amplifier, filter unit, and other parts with a dry or damp cloth when dust accumulates. Do not use detergents or polishes.

Clearing blockages
Unplug from the main power source. If the machine has been in use, leave it for 1 to 2 hours in order to allow the machine to cool down completely. Look for blockages in the air inlet holes and in the small aperture inside the air loop amplifier. Use a soft brush to remove debris.

Caution: Hot when in use
This machine is hot when in use and for a short period after use. Do not let bare skin touch hot surfaces. If children are present, consider positioning the machine out of their reach.

Battery replacement
Unscrew the battery compartment on the remote control. Loosen the base and pull to remove the battery.

Replacing the filter unit

When your non-washable filter unit needs replacing the machine will display the pattern shown. To replace the non-washable filter unit, follow these steps. If the machine has been in use, leave it for 1 to 2 hours before replacing the filter unit to allow the machine to cool down completely. Your Dyson machine is programmed to remind you to replace the filter unit after 12 months based on 12 hours of usage a day. Please note that your indicator will activate sooner with more use. The indicator is only a guide. Use in heavily polluted environments may require the filter unit to be replaced more regularly.

When you have reassembled your machine, press and hold the Standby on/off button for 6 seconds on the remote control to reset the filter indicator.

USING YOUR DYSON MACHINE
PLEASE READ THE ‘IMPORTANT SAFETY INSTRUCTIONS’ IN YOUR DYSON USER MANUAL BEFORE PROCEEDING. LOOKING AFTER YOUR DYSON MACHINE

• Do not carry out any maintenance or repair work other than that shown and described in your Dyson User manual, or advised by the Dyson Helpline.
• Always disconnect the plug from the mains outlet before inspecting for problems. If the machine will not operate, first check that the mains outlet has an electricity supply and that the plug is properly inserted into the outlet.
• If the fuse needs replacing, please check ‘User servicing instructions’.

OPERATION

• Ensure that the machine is fully assembled in line with the instructions before use.
• Do not dismantle the machine or use it without the loop amplifier fitted.
• The machine will not operate in heating mode unless the target temperature is above room temperature.
• Each time the heating mode is selected, it conducts a short calibration cycle. Airflow will be automatically controlled during this cycle. Once the calibration cycle is complete, it will revert to the selected airflow speed.
• The machine will not oscillate when the control buttons are pressed.
• Do not lubricate any part of this machine.

CONTROL WITHOUT REMOTE

• Press the power button on the machine to turn on/off.
• Press and hold the power button on the machine to adjust the target temperature.
• The target temperature will increase to a maximum before decreasing. If the target temperature is set at 0°C it will switch from heating to cooling mode.
• The airflow, diffused and personal heating modes, oscillation function, and sleep timer controls cannot be operated without the remote control.

LED DISPLAY

• The LED display will dim after 10 seconds of use.
• Press any button, other than the Standby ON/OFF, to reactivate.
• Do not press Standby ON/Off as this will turn the machine off.

SLEEP TIMER
To set the sleep timer, press and hold the Sleep timer button to select the desired time. When the time reaches zero, the machine will go into standby mode. To cancel, reduce the time until two dashes appear.

• The LED display will turn off after 10 seconds of inactivity – this is a power-saving feature and avoids light interference at night time.
• Press any button, other than the Standby ON/OFF, to reactivate.
• When the sleep timer is ON, do not press the Standby ON/OFF as this will turn the machine off and turn the sleep timer off too.

TILT FUNCTION
Carefully hold the base and the main body. Tilt the loop amplifier forward or backward for the required airflow angle.

AUTOMATIC CUT-OUT
For your safety, this machine is fitted with automatic cut-out switches that operate if the machine tips over or overheats. If the switches operate, unplug the machine and allow it to cool. Before restarting the machine, check and clear any blockages and ensure that the machine is on a solid level surface. In heating mode, the machine will automatically switch off after 9 hours of continuous use and will return to standby mode. To restart the machine, press the power button on either the remote control or the base.

TROUBLESHOOTING

Fault codes F4, F5, and F6: If one of these appears on the display, unplug the machine, wait for 30 to 60 seconds, and/or plug the machine into a different socket. If you continue to receive the fault code, please contact the Dyson Helpline.
Fault codes F2, F3, and F7: If one of these appears on the display, please contact the Dyson Helpline.

REPLACEABLE PARTS BATTERY REPLACEMENT
CAUTION

• Switch off and unplug the machine before replacing the batteries.
• Unscrew the battery compartment on the remote control. Loosen the base and pull to remove the battery.
• Do not install backward or short-circuit the batteries.
• Do not attempt to dismantle or charge the batteries. Keep away from fire.
• Always replace the screw in the remote control and refer to the battery hazard in the warning section.
• Follow battery manufacturers’ instructions when installing new batteries (battery type CR 2032).
• Limited functionality is available without the remote control (see ‘Control without remote’).

NON-WASHABLE FILTER UNIT

• Your filter unit is non-washable and non-recyclable.
• To replace your filter unit follow the steps as shown.
• Failure to replace the filter when prompted may result in changes to the product

DISPOSAL INFORMATION

• Dyson products are made from high-grade recyclable materials. Recycle where possible.
• Dispose of or recycle the battery in accordance with local ordinances or regulations.
• Keep the used batteries away from children as these can still harm children if swallowed.
• Your filter units are non-washable and non-recyclable.
• Dispose of the exhausted filter units in accordance with local ordinances or regulations.
• The battery should be removed from the machine before disposal.

DYSON CUSTOMER CARE

THANK YOU FOR CHOOSING TO BUY A DYSON MACHINE.
After registering your 2-year warranty, your Dyson machine will be covered for parts and labor (excluding filters) for 2 years from the date of purchase, subject to the terms of the warranty. If you have any questions regarding your Dyson machine, visit www.dyson.com.mx for online help, general tips, and useful information about Dyson. Alternatively, you can contact us via email or phone with your serial number and details of where and when you bought the machine. If your Dyson machine needs a repair, email or phone Dyson so we can discuss the available options. If your Dyson machine is under warranty, and it is a covered repair, it will be repaired at no cost. Your serial number can be found on your rating plate which is on the base of your machine.

PLEASE REGISTER AS A DYSON MACHINE OWNER
To help us ensure that you receive prompt and efficient service, please register as a Dyson machine owner.

• Online at www.dyson.com.mx/register
• Register by phone: 01 800 872 0154
• This will confirm ownership of your Dyson machine in the event of an insurance loss, and enable us to contact you if necessary.

IMPORTANT DATA PROTECTION INFORMATION
WHEN REGISTERING YOUR DYSON MACHINE:

• You will need to provide us with basic contact information to register your machine and enable us to support your warranty.
• When you register, you will have the opportunity to choose whether you would like to receive communications from us. If you opt-in to communications from Dyson, we will send you details of special offers and news of our latest innovations.
• We never sell your information to third parties and only use information that you Share with us as defined by our privacy policies which are available on our website at privacy.dyson.com

ELECTRICAL SPECIFICATIONS
CONNECTION INSTRUCTIONS

• Connect the plug on the power cord to a 127V AC power socket
• Do not unplug by pulling on the cord, firmly grasp the plug and remove it gently.
• Unplug the device from the AC power socket if you are not going to use the product for an extended period

THANK YOU FOR CHOOSING TO BUY A DYSON MACHINE
After registering your free 2-year warranty, your Dyson machine will be covered for parts and labor (excluding filters) for 2 years from the date of purchase, subject to the terms of the warranty. If you have any questions about your Dyson machine, please contact Dyson Customer Care with your serial number and details of where and when you bought the machine. Most questions can be solved by one of our trained Dyson Customer Care staff. Your serial number can be found on your rating plate which is on the base of the machine. Visit www.dyson.com.mx/support for online help, support videos, general tips, and useful information about Dyson Note your serial number for future reference.

This illustration is, for example, purposes only.

Dyson AB14 Airblade hand dryers

IMPORTANT SAFETY INSTRUCTIONS

WARNING

All electrical installation and repair work should be carried out by a qualified electrician or Dyson Service Engineer in accordance with current local codes or regulations. Risk of electric shock! If the casing is removed or handled improperly the internal components of the unit may cause harm or become permanently damaged. The unit is designed for dry, internal location only.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

Wiring

• Check that the electrical supply corresponds to that shown on the rating plate. If the product is connected to any electrical supply other than that stated on the rating plate permanent damage or improper/unsafe operation of the product may result.
• The product must be earthed.
• A means of all –pole disconnection must be incorporated into the fixed wiring, this and all wiring to the product must comply with all federal, state and local laws and applicable regulations, codes, and standards, including fire-rated construction.

Safety

• Use of protective equipment is recommended during the installation.
• Isolate the power before installation or service.

Installation

• Make sure that the unit is installed in compliance with all building codes and/or regulations.
• The unit must be mounted on a flat vertical wall capable of supporting the weight of the unit.
• Ensure no pipework (gas, water, air) or electrical cables, wires or ductwork are located directly behind the drilling/mounting area.
• To avoid contact with water from the user’s hands, do not install the unit above any electrical equipment.

DO NOT USE ANY JETWASH EQUIPMENT FOR CLEANING ON OR NEAR THIS UNIT

LOCATION

• Consult local and national accessibility codes and regulations for relevant installation guidelines. Conformity and compliance are the responsibility of the installer.
• If you are installing this hand dryer in a food handling or food manufacturing environment, please contact the Dyson Helpline for the specialist installation guide that supports this.

Important

• Please refer to the Dyson Owners Manual for details of the guarantee.

Fixings
To install this unit you will need (5) screws, toggle or masonry bolts and appropriate fittings for the wall type and weight of the unit (recommended minimum size of 7mm).

Remove fascia.

CAUTION: The fascia may have sharp edges.

• Remove the (6) tamper-proof screws from the unit with the service tool provided. Store the screws and mounting nuts safely.
• Remove the fascia as shown.

Selecting the height.

• Allow at least 200mm clearance under the unit.
• Recommended heights are shown, but may need to be adjusted for each individual installation.
• 990mm adult male height.
• 915mm adult female height.
• 815mm child/wheelchair user height UK.
• 840mm child/wheelchair user height ANZ.

Mount bracket to wall
Secure the bracket to the wall using appropriate fixings for the wall type and the weight of the main unit. Ensure the bracket is level.

Cable entry – rear/base.
The options for cable entry are from the rear, base, or either side.

• OPTION A: Cable entry into the rear of the unit. Only pry out one knockout from the backplate. The cable route is directly from the wall into the unit.
• OPTION B: Cable entry from the base of the unit. Ensure the cable is not trapped between the backplate and the wall.

Cable entry – side.
OPTION C: Cable entry from the side.
IMPORTANT: The unit is designed to have ONLY ONE side cable entry point, left or right.

• Ensure you work only on the side you have chosen for the cable entry point.
• Drill a 20mm diameter cable entry hole through the thin-wall section as illustrated.

Secure product to wall

• Hook the product on to the wall bracket. Mark the 3 fixing points, remove the product and drill the 3 holes.
  NOTE: For easier access to the lower fixing screw, temporarily remove the filter.
• Hook the backplate onto the wall bracket.
• Install the electrical cable.
• Secure the backplate to the wall.
• Replace the filter.

Electrical Connection

WARNING: Risk of electric shock

• Secure the live, neutral and earth wires into the correct terminal block locations.
• To avoid damage to the fascia, if entry is from the left-hand point in the backplate, ensure the cable is secured in front of the duct with the cable clip.

Attach fascia

• Replace the fascia as illustrated.
• Make sure that the clips on the top of the fascia are seated correctly.
• Insert and tighten the (2) anti-tamper screws into the middle of the fascia as illustrated.
• Insert and tighten the anti-tamper screws in the order shown ensuring the nuts in drawing 4 are installed.
• Test the unit for correct operation before affixing the (2) fascia caps.
  NOTE: Do not use a sealant when fixing the unit to the wall.

dyson 214744-01 V8 Absolute Cordless Vacuum Cleaner

In the box

• Your machine will come with one or more of these cleaner heads – not all will be included.
• The main body shows the handle and the bin attached.
• A brush bar is located inside the cleaner head and a suction control slider is located on the front.
• A soft fluffy brush bar is housed within the cleaner head. There is an electrical connector end that can attach to the end of the wand or directly to the machine.

Vacuum cleaner

• A rectangular dock that needs to be fixed to a wall with screws.
• The charger is a one-piece unit with the plug, connector end, and cable.
• Motorbar™ cleaner head De-tangling vanes automatically clear wrapped hair from the brush bar as you clean.
• Fluffy™ cleaner head Soft woven nylon removes large debris, while anti-static carbon fiber filaments extract fine dust from hard floors.

Wall dock
The Dyson cordless vacuum drops into the wall-mounted charging dock, ready for your next clean.

Charger
Charges your vacuum with or without a dock.

• The narrow connector end at the top connects to the bin and the wider end at the bottom connects to the cleaner head or tool.

Wand

Some tools may not be included. You can buy additional tools at www.dyson.com.

• This tool has a combination of the brush head and crevice tool together in one unit. The brush head slides down the crevice tool when needed.
• A long tool with an angled end
• A small cleaner head with an angled body housing the motor and an electrical connector to attach to the wand or directly to the machine.
• Pliable bristles and felt bumper strip on a narrow, tapered tool.
• A short nozzle with stiff bristles on the underside.

Combination tool
Two tools in one – wide nozzle and brush, for quick switching between cleaning and dusting tasks around your home or car.

Crevice tool
Engineered for precise cleaning around tricky edges and into hard-to reach narrow spaces.

Hair screw tool
Anti-tangle conical brush bar spirals hair off and into the bin. Motor-driven cleaning for smaller spaces.

Mini motorized tool
Motorized brush bar, concentrated in a smaller head to remove stubborn dirt from mattresses, upholstery, and stairs.

Soft dusting brush
Enclosed in a skirt of soft nylon bristles for a gentle, vacuum-assisted dusting of delicate objects and surfaces.

Stubborn dirt brush
Stiff nylon bristles dislodge ground-in dirt from coarse carpets, high traffic areas and car interiors.

• A wide, triangular-shaped nozzle.
• A flexible hose engineered from tough wire and durable plastic.

Fabric and mattress tool
Removes dust, dirt and allergens from mattresses and upholstery.

Extension hose
Adds up to 61cm of flexible reach to any tool attachment, to clean up high or down low in your home or car.

Getting started

Pull trigger to start cleaning

Two power modes
Toggle between Powerful mode – for longer suction – and MAX mode, for stronger suction. Just hold down the trigger and slide the control back and forth.

• The power mode button is located on the top of the machine between the bin and filter. Slide to the left for powerful cleaning and to the right for max mode.

Switch accessories quickly
The quick-release tools click into place, and release in moments by simply depressing the release switch.

Motorbar™ cleaner head
De-tangling vanes automatically clear wrapped hair from the brush bar as you clean.

Clean awkward spaces
Remove the wand and connect your chosen tool directly to the inlet pipe to use the vacuum as a handheld.

• Diagram showing the connection of the wand onto the main body, with the wand release button aligned with the top of the main body.
• A brush bar is located inside the cleaner head and a suction control slider is located on the front.
• Pointers to demonstrate that the tools can be connected directly to the main body or to the end of the wand.

Caring for your floors

Check that the underside of the cleaner head or tool is clean and free from any objects that may cause damage. Before vacuuming your flooring, rugs, and carpets, check the manufacturer’s recommended cleaning instructions. The brush bar on your machine can damage certain flooring. Some rug materials may fuzz if a rotating brush bar is used when vacuuming. If this happens, we recommend vacuuming without the motorised floor tool and consulting with your flooring manufacturer.

Charging your machine

Fully charge your machine before your first use. Connect to charger either directly or in the dock. A full charge will take approximately 4.5 hours. While your battery is charging, the LEDs will flash with the current level of charge. These lights will turn off once your machine is fully charged.

• Insert the charging cable into the charging point at the back of the vacuum, at the bottom of the handle. Plug the cable into a wall socket to begin charging.
• The charger connected from the power supply using the wall dock.
• The LED lights are located on the side of the battery unit.

Emptying your bin

Empty as soon as the dirt reaches the MAX level – don’t overfill. Using your machine when the dirt is above the MAX line may affect the performance and require more frequent filter washing.

• The MAX mark on the bin of the machine, showing that the dirt should not be filled over the Max mark when the machine is at the angle of normal use.

Release the dirt
Remove the wand from your machine. Hold your machine over the bin and pull the bin release catch upwards. The cyclone will slide up and the bin base will open.

• The bin release catch is located on the top of the cyclone where it joins the main body of your machine.

Minimise dust contact
Cover your bin tightly in a dustproof bag while you empty. Remove the bin carefully, seal the bag tightly and dispose.

Close the bin
Push down on the cyclone until it slides into position. Push the bin base upwards until it closes securely.

Cleaning your bin

Empty your bin as soon as the dirt reaches the MAX mark. You may need to clean the filter more often if you use your machine with a full bin.

Empty your bin
Remove the wand from your machine. Hold your machine over a bin and pull the bin release catch upwards. The cyclone will slide up and the bin base will open.

Remove the cyclone
Pull the bin release catch upwards. The cyclone will slide up and the bin base will open. Locate the cyclone release button behind the cyclone and push to remove the cyclone from your machine.

• The cyclone release button is located on the main body and is visible once the bin release button has been activated. The button to remove the bin is located on the bottom of the handle.

Remove the bin
Pull back on the red catch located on the base, slide the bin down and pull it off your machine.

Clean the bin
Wipe your bin with a damp, lint-free cloth. Don’t put the bin in a dishwasher or use detergents, polishes or air fresheners. Make sure the bin is completely dry before replacing.

Replace the bin
Align the tabs on the bin with the grooves on the main body and slide it upwards until it clicks into place.

Replace the cyclone
Slide the cyclone into the grooves of the main body and push down until it is in position. Push the bin base up until it clicks firmly shut.

Clearing blockages

Your machine is fitted with an automatic cut-out. If any part of it is blocked, your machine’s motor will pulse and won’t function until the blockage has been cleared. Disconnect your machine from the charger before looking for blockages. Be careful not to touch the trigger and be aware of sharp objects. Leave your machine to cool down before looking for blockages. Don’t use your machine when looking for blockages as this could cause injury.

• With the wand removed from the machine, check for blockages at both ends of the wand.

Washing filter A

Remove your filter

Lift the filter out of the top of the cyclone. Tap to remove excess dust and debris.

• The filter has a top with five arms that fit onto the cyclone body

Wash your filter

• Hold the open end of the filter under a running tap, until the water runs clear. Turn the filter upside down and tap it to remove excess water. Run water over the outside of the filter until the water runs clear. Squeeze and twist with both hands to make sure the excess water is removed.

Dry your filter
Leave your filter to dry for at least 24 hours in a well-ventilated, warm place. Do not dry your filter in a tumble-dryer or near a naked flame.

Important: your filter must be completely dry before you put it back into the machine. Your machine could be damaged if used with a damp filter.

• The filter will only fit correctly if the arms are aligned and the arrow on the top is pointing towards the main body of the machine.

Refit your filter
Align the arrow on the top of the filter with the bin release button. Push down to fit securely in place.

Washing filter B

Twist off your filter
Twist your filter anti-clockwise and pull it away from your machine.

Wash your filter
Wash the inside of the filter under cold, running water, rotating the filter to make sure all the inside is clean. Repeat until the water runs clear.

• The filter is placed under the tap with the water flowing into the open end of the filter

Shake out the water
Empty the filter and shake firmly to remove excess water. Keep shaking it until there’s no water coming from the filter.

Dry your filter
Place your tilter, with the open end tacing up, to dry. Leave your filter to dry for at least 24 hours in a well-ventilated, warm place. Do not dry your filter in a tumble-dryer or near a naked flame.

Important: your filter must be completely dry before you put it back into the machine. Your machine could be damaged if used with a damp filter.

Clearing obstructions from your Motorbar” cleaner head

Your Motorbar” cleaner head doesn’t have a washable brush bar. To maintain optimum performance, check your brush bar regularly and clear any obstructions. Make sure your machine is disconnected trom the charger and take care not to touch the trigger.

Remove your brush bar
Don’t put any part ot your machine in a dishwasher or use detergents, polishes or air fresheners. Press the cleaner head release button on the end of the wand. Place the cleaner head upside down. Use a coin to unlock the end cap. Twist the end cap and remove it from your brush bar. Don’t wash the end cap. Slide your brush bar out ot the cleaner head.

• The removal of the brush bars showing the lock in a horizontal position and the unlock symbol in the 6 o’clock position and the lock symbol in the 12 o’clock position.

Look for obstructions
Clear any debris from your brush bar. Check inside the cleaner head and remove any debris or blockages. Your Motorbar” cleaner head and brush bar aren’t washable. Wipe over with a damp lint-free cloth.

• The brush bar reinserted into the cleaner head and the end cap rotated to the locked position.

Replace your brush bar
Push the end cap back on to your brush bar and slide it back into the cleaner head. Turn the end cap clockwise into the locked position. Your cleaner head isn’t washable and should only be wiped over with a damp lint-free cloth.

Clearing blockages from your Hair screw tool

Your Hair screw tool doesn’t have a washable brush bar. To maintain optimum performance, check your brush bar regularly and clear any obstructions. Make sure your machine is disconnected from the charger and take care not to touch the frigger.

Remove the cover and brush bar
Remove the Hair screw tool from the wand or machine. Push the base plate open. Press the red lever down to rele ase the cleaner head cover. Pull the cleaner head cover off the main body of the tool.

• The location of lever to release the brush bar is located at the back of the Hair screw tool.

Look for obstructions
Pull your brush bar firmly to remove it from the main body. Check and remove any obstructions from all three parts of your Hair screw tool.

Re–assemble Hair screw tool

Put your brush bar back into position and press firmly until it clicks back into position. Check the red locking lever is in the unlocked position. Align the cleaner head cover with the guide on the main body. Push it down until it clicks into position. Push the red locking lever up until it clicks into position and push the base plate back into place.

• Slide the housing back on to the brush bar and push the lever on the back of the Hair screw tool upwards to lock.

Washing your Fluffy” cleaner head brush bar

Your Fluffy” cleaner head has a washable brush bar. To maintain optimum performance, check and wash your brush bar regularly. Make sure your machine is disconnected from the charger and take care not to touch the trigger.

Remove your brush bar
Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners. Press the cleaner head release button on the end of the wand. Place the cleaner head upside down. Push the end cap up fully and pull the brush bar out of the cleaner head. Remove the end cap from the brush bar. Don’t wash the end cap.

• The end cap is located atthe side of thecleaner head. Push this upwards to unlock the brush bar. Don’t wash the end cap.
• The two ends of the main brush bar showing the closed in end being the correct one to have facing upwards when leaving the brush bar to dry.
• The brush bar has an open end and a closed end. Stand upright, with the closed end facing upwards, to dry.

Wash and dry your brush bar
Hold your brush bar under running water and gently rub to remove any lint or dirt. Remove as much excess water as possible, run your hand down the length of the brush bar to squeeze out the water. Stand your brush bar upright, with the closed end at the top. Leave to dry completely for at least 24 hours.

Replace your brush bar
Before replacing, check that your brush bar is completely dry. Reattach the end cap to your brush bar. Slide your brush bar into the cleaner head. Push the end cap back down to the closed position.

• The end cap should be attached to the cleaner head at an angle less than 90°, any angle greater than this will not allow the end cap to close.
• The brush bar reinserted into the cleaner head and the end cap rotated to the locked position.

Cleaning your fools

Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners. Wipe with a damp, lint-free cloth, without touching the connector end. Make sure your tools are completely dry before using.

Looking after your machine

To always get the best performance from your machine, i’s important to clean it regularly and check for blockages.

Look after your machine
If your machine is dusty, wipe with a damp lint-free cloth. Check for blockages in the cleaner head, tools and main body of your machine. Wash your filter regularly and leave to dry completely. Don’t use detergents or polishes to clean your machine.

Look after your battery
To get the best performance and life from your battery, use Powerful suction mode. Your machine won’t operate or charge if the ambient temperature is below 5°C (41°F). This is designed to protect both the motor and the battery.

Your serial numbers
You can register your machine using the serial number found on the bottom of your machine.You can find your serial numbers on your machine, battery and charger. Use your serial number to register.

DYSON CUSTOMER CARE

THANK YOU FOR CHOOSING TO BUY A DYSON MACHINE

After registering your two-year Dyson guarantee, your Dyson machine will be covered for parts and labour (excluding replacement filters where there is no defect) for two years from the date of purchase, subject to the terms of the guarantee.
If you have any questions about your Dyson machine, call the Dyson Helpline with your serial number and details of where and when you bought the machine. Most questions can be solved over the phone by one of our trained Dyson Helpline staff.
Your serial number can be found on your rating plate which is on the base of your machine
Visit our website to register your Dyson full parts and labour guarantee online, and for online help, support videos, general tips and useful information about Dyson.
AU: www.dyson.com.au/support NZ: www.dyson.co.nz/support Note your serial number for future reference

REGISTER YOUR DYSON 2-YEAR GUARANTEE TODAY

IMPORTANT SAFETY INSTRUCTIONS

BEFORE USING THIS APPLIANCE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN THE USER MANUAL AND ON THE APPLIANCE.
When using an electrical appliance, basic precautions should always be followed, including the following:

THE APPLIANCE AND THE REMOTE CONTROL BOTH CONTAIN MAGNETS.

1. Implanted medical devices such as pacemakers and defibrillators may be affected by strong magnetic If you or someone in your household has an implanted medical device or defibrillator, avoid placing the remote control in a pocket or near to the device.
2. Credit cards and electronic storage media may also be affected by magnets and should be kept away from the remote control and the top of the

These warnings apply to the appliance, and also where applicable, to all tools, accessories, chargers or mains adaptors.

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:

1. When used in heating mode the appliance is hot when in use and for a short period after To avoid burns, do not let bare skin touch hot surfaces. When moving the appliance hold it by the base, not the air loop amplifier.
2. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains, at least 9m (3 feet) from the front of the appliance and keep them away from the sides and rear when the appliance is plugged in.
3. Use only as described in the Dyson User Do not carry out any maintenance other than that shown in the manual, or advised by the Dyson Helpline. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
4. Ensure that the machine is fully assembled in line with the instructions before Do not dismantle the machine or use without the loop amplifier fitted.
5. Do not allow to be used as a toy. Close attention is necessary when used by or near children. Children of less than 3 years should be kept away unless continuously Children should be supervised to ensure that they do not play with the appliance and remote control.
6. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards Children aged from 3 years and less than 8 years shall not plug in, regulate and clean
   the appliance or perform user maintenance. CAUTION – Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

7. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction by a responsible person concerning use of the appliance to ensure that they can use it
8. Suitable for dry locations ONLY. Do not use outdoors or on wet surfaces. Do not use in bathrooms, laundry areas or similar indoor locations. Never locate the appliance where it may fall into a bath or other water Do not use or store where it may get wet or in the immediate surroundings of a bath, a shower, or a swimming pool.
9. This appliance has hot parts Do not use it in areas where petrol, paint, or flammable liquids are used or stored or where their vapours are present. Do not use in conjunction with or directly next to an air freshener or similar products.
10. Do not locate directly below a mains electricity supply
11. Always plug directly into a wall Never use with an extension cable as overloading may result in the cable overheating and catching fire.
12. Do not handle any part of the plug or appliance with wet
13. Do not use with a damaged cable or If the supply cable is damaged it must be replaced by Dyson, its service agent or similarly qualified persons in order to avoid a hazard.
14. Do not unplug by pulling on the To unplug, grasp the plug, not the cable.
15. Do not stretch the cable or place the cable under Keep cable away from heated surfaces.
16. Do not run cable under Do not cover cable with throw rugs, runners or similar coverings. Arrange cable away from traffic areas and where it will not be tripped over.
17. To prevent a possible fire, do not use with any opening or exhaust blocked, and keep free of dust, lint, hair, and anything that may reduce airflow. Do not put any object into the inlet grille or the exhaust opening as this may cause an electric shock or fire, or damage the
18. Do not use on soft surfaces, such as a bed, where openings may become
19. In order to avoid overheating, do not cover the
20. For the best performance, place on the floor, in the corner of the room, at least 1m from any wall and facing into the centre of the
21. Turn off all controls before Unplug before connecting any tool or accessory.
22. Do not use any cleaning agents or lubricants on this Unplug before cleaning or carrying out any maintenance.
23. If there is a loose fit between the plug and the socket or the plug becomes very hot, the socket may need to be Check with a qualified electrician to replace the socket.
24. Chemical Burn and Choking Hazard. Keep batteries away from children. This product contains a lithium button/coin cell If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
25. If the appliance is not working as it should, if it has received a sharp blow, if it has been dropped, damaged, left outdoors, or dropped into water, do not use and contact the Dyson
26. Contact the Dyson Helpline when a service or repair is Do not disassemble the appliance as incorrect reassembly may result in an electric shock or fire.
27. Do not put any object into openings or the inlet Do not use with any openings blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
28. Always carry the appliance by the base, do not carry it by the loop
29. To avoid a tripping hazard wind the cable when not in
30. Do not use near furnaces, fireplaces, stoves or other high temperature heat
31. Do not use in conjunction with or directly next to an air freshener or similar products. Do not spray or apply perfumes directly on or near the Keep essential oils and chemicals away from the appliance.
32. The appliance should not be forcefully turned or oscillated, under any This will cause damage to the oscillation mechanism.
33. When removing or replacing the filter, take care to keep your fingers
34. Do not use this appliance in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is

IMPORTANT SAFETY FEATURES

For your safety this appliance is fitted with automatic cut-out switches that operate if it tips over or overheats. If the switches operate, unplug the appliance and allow it to cool. Before restarting, check and clear any blockages and ensure that the appliance is on a solid level surface.

READ AND SAVE THESE INSTRUCTIONS

THIS DYSON APPLIANCE IS INTENDED FOR HOUSEHOLD USE ONLY

Power

Each time the heating mode is selected, it conducts a short calibration cycle. Airflow will be automatically controlled during this cycle. Once the calibration cycle is complete, it will revert to the selected airflow speed
On first use, the machine will default to a temperature 3°C higher than the detected room temperature.
Thereafter, the machine will remember the last target temperature set
Select the desired room temperature. Pressing the large red button increases the target temperature by 1°C; the smaller red button decreases it by 1°C. The machine will not operate in heating mode unless the target temperature is above the room temperature.

Remote control

Remote control docks magnetically. Attach the remote control to the top of the machine with the buttons facing down.

Airflow speed control

Press the red thermostat control button until the digital display
shows the target room temperature. The power button light will change from blue to red to indicate that you have entered heating mode. The red circle will disappear when the target room temperature is reached. Once the target room temperature has been reached, the machine will stop heating the air. If the room temperature falls below the target room temperature, the machine will start to heat again.

Press the blue cool mode button to enter cool mode.
The power button light will change from red to blue to indicate that you have entered cool mode. To adjust the airflow speed use the airflow control button.

Sleep timer

To set the sleep timer, select the desired time. When time reaches zero, the machine will go into standby mode. To cancel, increase the time until two dashes appear
When using the sleep timer, the LED display will turn off after 10 seconds of inactivity.

Tilt function

Carefully hold the base and the main body. Tilt the amplifier forward or backward for the required airflow angle.

Diffused and focused modes

Diffused mode
Press the wide angle button to change from a personal directed airflow to a whole room airflow.
Heating and cooling modes work in this mode.

Focused mode
Press the narrow angle button to change from a whole room airflow to a personal directed airflow.
Heating and cooling modes work in this mode.

Oscillation and airflow speed control

Oscillation control
To start the machine oscillating, press the oscillation control button. To stop the machine oscillating, press it again. The machine will not oscillate when the control buttons are pressed.

Airflow speed control
To change the airflow speed press the airflow control button.
The digital display will show the new speed; after 3 seconds it will change back to the target temperature

Clearing blockages

Unplug from the mains electricity supply. If the machine has been in use, leave for 1 to 2 hours before cleaning to allow the machine to cool completely. Dust may accumulate on the surface of the machine.
Wipe dust from the loop, filter unit and other parts with a dry or damp cloth when dust accumulates. Do not use detergents or polishes.

Cleaning

Ensure that the machine is unplugged. If the appliance has been in use, leave for 1 to 2 hours in order to allow the machine to cool down completely. Look for blockages in the air inlet holes and in
the small aperture inside the air loop amplifier. Use a soft brush to remove debris.

Caution: hot when in use

This machine is hot when in use and for a short period after use. Do not let bare skin touch hot surfaces. If children are present, consider positioning the machine out of their reach.

Battery replacement

Battery type CR 2032

Unscrew the battery compartment on the remote control. Loosen the base and pull to remove the battery.

Replacing the filter unit

When your non-washable filter unit needs replacing, the machine will display the pattern shown. To replace the non-washable filter unit, follow these steps. If the machine has been in use, leave for 1 to 2 hours before replacing the filter unit to allow the machine to cool down completely. Your machine is programmed to remind you to replace the filter unit after 12 months based on 12 hours usage a day. Please note your indicator will activate sooner with more use. The indicator is only a guide and you may need to replace the filter unit more regularly.

Replacing the filter unit

USING YOUR DYSON MACHINE

PLEASE READ THE ‘IMPORTANT SAFETY INSTRUCTIONS’ IN YOUR DYSON USER MANUAL BEFORE PROCEEDING.

LOOKING AFTER YOUR DYSON MACHINE

• Do not carry out any maintenance or repair work other than that shown in your Dyson User manual, or advised by the Dyson
• Always disconnect the plug from the mains before inspecting for If the machine will not operate, first check that the mains socket has an electricity supply and that the plug is properly inserted into the socket.

OPERATION

• Ensure that the machine is fully assembled in line with the instructions before Do not dismantle the machine or use without the loop amplifier fitted.
• The machine will not operate in heating mode unless the target temperature is above the room
• Each time the heating mode is selected, it conducts a short calibration Airflow will be automatically controlled during this cycle. Once the calibration cycle is complete, it will revert to the selected airflow speed.
• The machine will not oscillate when the control buttons are
• Do not lubricate any part of this

CONTROL WITHOUT THE REMOTE

• Press the Standby on/off button on the machine to turn it on and off.
• Press and hold the Standby button on/off on the machine to adjust the target The target temperature will increase to a maximum before decreasing. If the target temperature is set at 0°C it will switch from heating to fan mode.
• The airflow, diffused and focused heating modes, oscillation function and sleep timer controls cannot be operated without the remote

LED DISPLAY

• The LED display will dim after ten seconds of use (the Standby on/off button does not dim).
• Press any button, other than the Standby on/off button, to reactivate.
• Do not press the Standby on/off button as this will turn the machine off.

SLEEP TIMER

• To set the sleep timer, select the desired time. When time reaches zero, the machine will go into Standby mode. To cancel, increase the time until two dashes appear.
• The LED display will turn off after ten seconds of inactivity – this is a power saving feature and avoids light interference at night
• Press any button, other than the Standby on/off button, to reactivate.
• When the sleep timer is on, do not press the Standby on/off button as this will deactivate the sleep timer and turn the machine

TILT FUNCTION

• Carefully hold the base and the main Tilt the amplifier forward or backward for the required airflow angle.

AUTOMATIC CUT-OUT

• For your safety, your machine is fitted with automatic cut-out switches that operate if the machine tips over or overheats. If the switches operate, unplug your machine and allow it to Before restarting your machine, check and clear any blockages and ensure that your machine is on a solid level surface.
• In heating mode, the appliance will automatically switch off after nine hours of continuous use and will return to Standby To restart the machine, press the Standby on/off button on either the remote control or the base.

TROUBLESHOOTING

• Fault codes F4, F5, F6: If one of these appears on the display, unplug the machine, wait for 30 to 60 seconds and/or plug the machine into a different socket. If you continue to receive the fault code, please contact the Dyson
• Fault codes F2, F3, F7: If one of these appears on the display, please contact the Dyson

REPLACEABLE PARTS BATTERY REPLACEMENT

CAUTION

• Unscrew the battery compartment on the remote Loosen the base and pull to remove the battery.
• Do not install backwards or short circuit the
• Do not attempt to dismantle or charge the Keep away from fire.
• Always replace the screw in the remote control and refer to the battery hazard in the warning
• Follow battery manufacturers’ instructions when installing new batteries (battery type CR 2032).
• Limited functionality is available without the remote control (see ‘Control without the remote’).

NON-WASHABLE FILTER UNIT

• Your filter unit is non-washable and non-recyclable.
• To replace your filter unit follow the steps as
• Failure to replace the filter when prompted may result in changes to product performance and
• A new filter unit can be purchased at dyson.com.au

DISPOSAL INFORMATION

Dyson products are made from high-grade recyclable materials. Please dispose of this product responsibly and recycle where possible.

When your Dyson machine reaches the end of its life, we can assist with its safe disposal. You can send your old Dyson machine back to us (at our cost) and we will organise for it to be recycled.*

*Please note that not all parts are recyclable. Recycling of parts is subject to the capabilities of third party suppliers. Available in Australia only.

Simply:

1. Box up your old Dyson
2. Take the package to your local post office and send it to the address below:

Dyson We Recycle Reply Paid 83215 Dyson Service Centre 8–10 Mangrove Lane

Taren Point, NSW 2229

• Keep the used batteries away from children as these can still harm children if
• Dispose of the exhausted filter unit(s) in accordance with local ordinances or
• The battery should be removed from the machine before

DYSON CUSTOMER CARE

THANK YOU FOR CHOOSING TO BUY A DYSON MACHINE

After registering your two-year Dyson guarantee, your Dyson machine will be covered for parts and labour for two years from the date of purchase, subject to the terms of the guarantee. If you have any questions about your Dyson machine, call the Dyson Helpline with your serial number and details of where and when you bought the machine. Most questions can be solved over the phone by one of our trained Dyson Helpline staff.

Your serial number can be found on your rating plate which is on the base of your machine.

• If your Dyson machine needs a service, call the Dyson Helpline so we can discuss the available

DYSON 2-YEAR GUARANTEE

Terms and conditions of the Dyson 2-year guarantee

AUSTRALIAN CONSUMER LAW

In addition to your rights under the Dyson guarantee, we also provide the following statement as required by the Australian Consumer Law: In Australia, your Dyson machine comes with statutory guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have your Dyson machine repaired or replaced if it fails to be of acceptable quality and the failure does not amount to a major failure.

NEW ZEALAND CONSUMER LAW

Under the New Zealand Consumer Guarantees Act 1993, if the product is not of acceptable quality but that defect is not substantial, Dyson may choose whether to repair or replace the product. If a repair will be difficult, Dyson may instead provide you with a refund. If a product’s defect is substantial or cannot be fixed, you can ask for either a refund, replacement product, or compensation for any reduction

in that product’s value. You are also entitled to compensation for any other reasonably foreseeable loss caused by that substantial defect.

WHAT IS COVERED

• The repair or replacement of your Dyson machine (at Dyson’s discretion) if it is found to be defective due to faulty materials, workmanship or function within two years of purchase (if any part is no longer available or out of manufacture, Dyson will replace it with a functional replacement part).
• This Dyson guarantee will only be valid if the machine is used in the country in which it was

WHAT IS NOT COVERED

Under your Dyson guarantee, Dyson shall not be liable for costs of repair or replacement of a product incurred as a result of:

• Damage caused by not carrying out the recommended machine
• Accidental damage, faults caused by negligent use or care, misuse, neglect, careless operation or handling of the Dyson machine which is not in accordance with your Dyson User
• Use of the Dyson machine for anything other than normal domestic purposes in the country of
• Use of parts not assembled or installed in accordance with the instructions of
• Use of parts and accessories which are not genuine Dyson
• Faulty installation (except where installed by Dyson).
• Repairs or alterations carried out by parties other than Dyson or its authorised
• Blockages – refer to the illustrations and the section ’Clearing blockages‘ in your Dyson User manual for details on how to look for and clear
• Normal wear and tear (e.g. fuse ).
• Reduction in battery discharge time due to battery age or use (where applicable).
• Whether or not the Dyson guarantee applies, you may have rights and remedies available to you under Australian or New Zealand Consumer

OTHER TERMS RELATING TO THE DYSON GUARANTEE

• The Dyson guarantee becomes effective from the date of
• All work will be carried out by Dyson Appliances (Aust.) Pty Limited, Dyson New Zealand Limited (NZ) or their authorised
• Any parts replaced by Dyson or its service agents will become the property of Dyson Appliances (Aust.) Pty Limited or Dyson New Zealand Limited (NZ).
• You must provide proof of purchase for your Dyson machine in order to make a claim under the Dyson
• Under the Dyson guarantee, the repair, replacement and any associated delivery charges (both to and from Dyson) will be at no cost to
• Whether or not the Dyson guarantee applies, you may have rights and remedies available to you under Australian or New Zealand Consumer

IMPORTANT DATA PROTECTION INFORMATION

When registering your Dyson machine:

• You will need to provide us with basic contact information to register your machine and enable us to support your Dyson
• When you register, you will have the opportunity to choose whether you would like to receive communications from If you opt-in to communications from Dyson, we will send you details of special offers and news of our latest innovations.
• We never sell your information to third parties and only use information that you share with us as defined by our privacy policies which are available on our website privacy.dyson.com.

Why register?

Expert advice
Free phone and live chat support.

Hassle-free replacement
The Dyson Guarantee includes replacement of your machine when it can’t be repaired. Fast.

How to’ Videos
To help you get the most from your machine. Quick and easy.

Exclusive owner benefits
Priority access to previews of new Dyson technology, events and offers.

Helpful tips
Tailored reminders that will keep your machine working at its best, for longer.